Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 25, No. 1 (2001)

Vol. 25, No. 1 (2001)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 28–31

44 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

David Gammel

David Gammel, 91 Johnson Road, Scott, Arkansas 72142 (ph 501 961-9374)

“This idea makes it easier to break lug bolts loose. Take a piece of 4-in. dia. PVC pipe and drill a 3/4-in. dia. hole all the way through the pipe. Insert a 1/2-in. drive socket extension through the hole and attach it to the lug bolt. Break as many lug nuts loose as you can from this position. You can turn the pipe upside down in order to change the height of the extension and reach the other nuts. Or, you can pull the vehicle or implement forward or backward just far enough to get the other lug nuts in position.

“The pipe allows the extension to apply a steady, even pressure on the bolts so they won’t break off.”

From the archive · Full text
Reader shop tip 1 of 2

Tom Williams Machine

Individual tip 1 of 2 from this reader’s published contribution.
Tom Williams Machine, Inc., HCR 1, Box 1-A, Aurora, Mo. 65605 (ph 417 678- 3723; fax 417 678-6000)

“We made our 5-gal. wet and dry vacuum easier to carry by bolting a pair of small brackets to the sides of the vac and attaching a 5-gal. pail handle to them. Without a handle, the vac is awkward to carry, especially when it’s full.

From the archive · Full text
Reader shop tip 2 of 2

Tom Williams Machine

Individual tip 2 of 2 from this reader’s published contribution.
Tom Williams Machine, Inc., HCR 1, Box 1-A, Aurora, Mo. 65605 (ph 417 678- 3723; fax 417 678-6000)

“I also mounted a pail handle on top of a 3-gal. pump-up spray tank and mounted a 1-in. dia. PVC pipe alongside the tank for storing the sprayer wand. I ran a No. 8 wire band around the tank and secured the pail handle to it. I also ran a wire band around the bottom of the tank and used plumber’s tape to attach the pipe to the band. The tank was originally designed to be carried by a metal hand loop secured to a circular lid. However, if you accidentally twist the lid as you hold onto the loop the lid can unlock and fall into the tank. To solve the problem I installed a smooth wire lock around the raised base of the pumper to keep the lid loop from accidentally turning. I also made and inserted a filter under and inside the pump-locking device in order to keep weed seeds and small trash, etc., from getting inside the pump tank.”

From the archive · Full text
Reader shop tip

Joe Strullmyer

Joe Strullmyer, St. Peter, Ill.

“I use this modified free-stand-ing jack to lift objects in my shop. It’s always ready to go and saves a lot of time and effort. It’s supported by a base made from square steel tubing and is held steady by a pair of steel rods that extend from the back of the base up to the top of the jack. The expanded base assures a better foundation to lift from if I want to use it outside the shop in soft areas. A long handle provides extra leverage when lifting the object. I recently used the jack to lift a broken spray boom.”

From the archive · Full text
Reader shop tip

Veryl Reiher

Veryl Reiher, Gillespie, Ill.

“I came up with a tool to help me measure the distance between front wheels on tractors, cars, and pickups, etc., so that I can make correct adjustments to tie rods. I used a 40-in. length of lightweight 1/4-in. dia. pipe and a 3-ft. long, 5/16-in. threaded Redi-bolt with a nut on it. The Redi-bolt telescopes into the pipe.

“The distance between the front wheels ahead of the axle should generally be 1/8 in. less than the distance behind the axle. I measure the distance between the front wheels by loosening the nut and placing the pipe and Redi-bolt between the wheels, then running the nut down against the pipe. When I move the pipe and Redi-bolt behind the axle, there should be a 1/8-in. gap between the end of the Redi-bolt and the tire. This slight amount of tow-in is needed in order to prevent the tractor from wandering and also to save unnecessary wear on tires. It works a lot better than using a tape measure, and it costs far less than commercial units designed to do the same job.”

From the archive · Full text
Reader shop tip

Edward M. Storch

Edward M. Storch, RR 4, Mannville, Alberta, Canada T0B 2W0 (ph 780 763- 2214)

“My hand-made knives are satin finished and are in use world wide. I custom make them using the same “forge welding” process that was used by old time blacksmiths. The idea behind forge welding is to heat the metal, put the flux on, and hammer-weld objects together. Using this process I can take a piece of steel cable or roller chain from a farm machine, heat it, flux it, and forge weld it into a bar which I later turn into a knife. The pattern of the different types of alloys in the steels shows up in the finished product. It looks quite artistic. I could use more common coal forges, but they’re hard to get and are messy to use. Using my propane-powered forge welding equipment I can have the material hot enough to weld in only about 10 minutes.

“I use a tangental venturi propane forge equipped with a central salt pot to heat treat the steel. It consists of a 16-in. long, 8 1/2-in. dia. steel pipe mounted on rollers. I line the inside of the pipe with a high temperature, heat-resistant fiber and cut a rectangular hole in the side of the pipe for the flame to exit. The flame cuts in at an angle and corkscrews around inside the pipe through a smaller 2-in. dia. pipe that’s welded inside.

“After I’ve heated the steel I use a homemade 42-ton hydraulic press to shape it. The press is equipped with a 2-stage hydraulic pump and a 6-in. dia. hydraulic cylinder. It has a capacity of 16 gal. per minute at 600 psi or 4 gal. per minute at 3,000 psi. I made different dies for the press which allow me to weld the material together flat or square. Or, I can use a homemade, air-operated, 65-lb. hammer that cycles up and down up to three times per second. Using both the hydraulic press and the air hammer makes for a much better end product.

“I also built my own 2 by 72-in. belt grinder for shaping the knives and for other general shop work. It’s operated by a 2 hp electric motor.

“I teach knife-making classes in my shop. You can see examples of my work at my W e b s i t e : www.Storchknives.com.”

From the archive · Full text
Reader shop tip

Frankie Purser

Frankie Purser, 680 Purser Rd., Vanceboro, N.C. 28586 (ph 252 244-0750)

“I installed a kit from Ford New Holland on my TW 15 tractor that lets me disconnect the remote hydraulic outlets without having to get off the tractor and use levers. The kit consists of a small Teflon plate with double-sided tape on it. Unfortunately, the first time I used a power washer to clean the tractor the Teflon plate blew off. Oil started leaking out of the outlets and they also became exposed to dust and moisture, etc. The only way to cover the remotes is to buy new lever-less remote outlet housings from the company that sell for $250 to $275 apiece.

“I solved the problem on my own using a 1 by 1 1/2-in. piece of aluminum flat bar that’s 1/8 in. thick. I drilled a hole in the middle of the bar and threaded it to accept a 8/32-in. machine screw, which I inserted through the original housing that held the lever. I put high temperature silicone around the plate and a little on the threads of the machine screw to form a seal. I haven’t had any problems since I installed it. I think this idea would work on all 10 and 30 series New Holland tractors equipped with remote lever systems.”

From the archive · Full text
Reader shop tip

Kenton Brewer

Kenton Brewer, Herndon, Ky.

“In a re-cent issue of FARM SHOW a reader described how he breaks down tire beads. He lays the tire on a concrete floor and drives his tractor or pickup over the edge of the tire. However, I don’t think this method is the safest way to break seals because if you drive up on the side of a tire, it can spring up and damage the fender and/or bumper or bend the wheel rim and even cause personal injury.”

From the archive · Full text
Reader shop tip

James Feldman

James Feldman, Northfield, Minn.

“I have a 12-ton wagon gear that carries a center dump, 375-bu. gravity box. I lost the dust cap on one wheel (a 20-in. truck tire and rim) and put off fixing it for some time. When I finally cleaned up the hub to put in new bearings and seals, I discovered the race had turned in the hub and wore a deep groove in it. I had been hearing about JB Weld so I decided to try it on the hub. I’ve used the gravity box to haul a lot of loads since then without any problems. JB Weld is a great product.”

From the archive · Full text
Reader shop tip 1 of 2

Murray Blackstone

Individual tip 1 of 2 from this reader’s published contribution.
Murray Blackstone, Caribou, Maine

“I used pieces of scrap metal to make a ‘spark guard’ to contain the sparks on my 14-in.

chop saw. My shop has wooden walls and I was worried that sparks could cause a fire. The spark guard consists of a 14-in. sq. steel plate that angles toward the saw and mounts on a pair of angle irons. There’s a handle on top. Whenever I use the saw I simply set the spark guard in front of it.

From the archive · Full text
Reader shop tip 2 of 2

Murray Blackstone

Individual tip 2 of 2 from this reader’s published contribution.
Murray Blackstone, Caribou, Maine

“Another idea I had was to use a 6-in. dia., 2-ft. length of well casing pipe to make a prybar holder. It keeps my prybars organized and makes it easy to find the one I want without having to dig around in toolbox drawers. I welded short lengths of small diameter pipe around the pipe and then welded one end of the pipe to a square steel plate. I keep large prybars in the big pipe and smaller prybars, as well as screwdrivers, in the shorter pipes. I keep it on my work bench.”

From the archive · Full text
Reader shop tip

Daniel Homes

Daniel Homes, 2/3 Station St East Kew, Melbourne, Victoria, Australia 3102 (ph 011 3 985-98120; E-mail: [email protected])

“I’ve invented a new tool for marking out contour lines on landscapes. Works great for laying out tracks, fences and tree belts along contour lines. My idea can be simply described as a scooter with a liquid level attached, which allows the operator to see that the scooter is level. An aerosol spray can is mounted on the front forks so the operator can easily mark the ground. The operator marks a series of points which will be on contour if the level is kept horizontal.

“I’m looking for a company to market the idea.”

From the archive · Full text
Reader shop tip

Eugene G. Johnson

Eugene G. Johnson, Rapid River, Mich.

“I had a 10 cu. ft. lawn trailer equipped with 16.00 by 4.00 pneumatic tires that I pulled behind my 3-wheel ATV. However, the tires were undersized and the axle was so narrow that when the trailer was loaded it could eas-ily tip over. I solved the problem by replacing the tires with 18 by 800 by 8 turf tires off a scrapped-out riding mower which I already had. I also lengthened the axle to match the ATV track and lowered the axle by welding in two new sockets so the new tires clear the box. I also milled a new keyway with a slight arc in each wheel bearing socket in order to provide a better surface for the bearing.

“Now the trailer is much more stable and I can use it to pull heavy loads with ease. Also, the wider tires pull much easier over soft ground.”

From the archive · Full text
Reader shop tip

John R. Spaetti

John R. Spaetti, Evansville, Ind.

“To make sure that the hydraulic couplers on my tractor are hooked up correctly, I paint the remote hydraulic tips red for the first outlet; white for the second outlet; and blue for the third outlet. Now my co-workers always get the hoses hooked up right the first time.”

From the archive · Full text
Reader shop tip

Matthew Lebold

Matthew Lebold, Kennabeek, Ontario

“Over the years we’ve worked on different IH tractors with stuck priority valves and have come up with an easy way to remove the valves. We push a 6-in. long, 1/4-in. dia. fuel line onto a 1/4-in. threaded rod and put a nut on each end of the rod. Then we install the entire assembly inside the priority valve and tighten the lower nut to expand the hose. By pulling on the assembly the valve will come out.”

From the archive · Full text
Reader shop tip 1 of 4

Glen Teel

Individual tip 1 of 4 from this reader’s published contribution.
Glen Teel, Hays, Kansas

“The clutch slave cylinder on my 1988 Chevrolet S-10 pickup started leaking and the company wanted more than $90 for repair parts. I didn’t want to spend that much so I bought a 50 cent O-ring and mounted it over the plunger and rubber seal. I made this modification more than a year ago and it still works fine.

From the archive · Full text
Reader shop tip 2 of 4

Glen Teel

Individual tip 2 of 4 from this reader’s published contribution.
Glen Teel, Hays, Kansas

“I use my shop vac to clean hair and other debris out of the drains in our kitchen sink and bathtub. I simply stick the vac hose over the drain. If there’s an overflow in the sink or bathtub I put duct tape over it to keep it air tight.

From the archive · Full text
Reader shop tip 3 of 4

Glen Teel

Individual tip 3 of 4 from this reader’s published contribution.
Glen Teel, Hays, Kansas

“I keep some imitation vanilla in my shop in case I ever burn myself. When applied immediately to a burn, vanilla keeps it from blistering and stops the sting.

From the archive · Full text
Reader shop tip 4 of 4

Glen Teel

Individual tip 4 of 4 from this reader’s published contribution.
Glen Teel, Hays, Kansas

“If I have to work in the dark and want to use both hands, I tape a clothespin onto a miniature flashlight and then clip the clothespin onto the bill of my hat. It works like a miner’s light. Great for doing electrical work in the dark.”

From the archive · Full text
Reader shop tip

Glenn Sethre

Glenn Sethre, Longview, Wash.

“I think any place that isn’t well lit and that is subject to foot traffic at night should have motion detector lights for safety and convenience, whether it’s for a house, garage, shop or whatever. Motion detector lights are as valuable on farms as they are in town and you can pick them up cheap”

From the archive · Full text
Reader shop tip

Valen Boettger

Valen Boettger, Rose Prairie, Canada

“We got a flat tire on our 1972 Kenworth semi tractor and the bead came off. We were able to reseat it by spraying a couple seconds worth of quick-start fluid into the tire through the unseated bead and then lighting it. To light the fluid we taped a small propane torch to the end of a 10-ft. stick. We first washed around the bead with soap and water before trying to seat it. The big advantage was that we didn’t have to take the tire off the truck. This idea would probably work on any size tire. However, you must be careful to stay well out of the way of the tire in case it blows up.”

From the archive · Full text
Reader shop tip

John Dyer

John Dyer, Kalispell, Montana

“Years ago a mechanic told me how to remove bolts that break off flush without doing any drilling. You first weld a washer that’s slightly smaller than the bolt to the top of it, then weld a nut onto the washer and use a wrench to unscrew it. The heat from the welding process helps release the bolt which makes it easier to unscrew. I’ve used this idea many times and it really works. Sometimes I can remove the bolt even if it has broken off ‘below flush’ by piling up welding material in the center of the bolt. It helps to have a small wire feed welder.”

From the archive · Full text
Reader shop tip

Keith D. Hight

Keith D. Hight, Spearman, Texas

“To keep dust caps from falling off wheel bearings, I bend a metal strip into an ‘S’ shape and drill a hole into one end. Then I remove one of the lug nuts from the wheel and slide the strap over the bolt, then press the opposite end of the strap down onto the dust cap and retighten the nut. It’s a simple, low-cost solution.”

From the archive · Full text
Reader shop tip

Glen Schweppe

Glen Schweppe, Syracuse, Neb.

“We added a door on back of both of our New Holland 816 side-unload forage wagons so that we can climb inside and use a pressure washer to clean them out.

“Corn silage is corrosive and can rust things up. We clean out the wagons every time we switch crops so they’ll last longer. We often spend a half day cleaning them up, running unloading chains real slow as we wash. It keeps the wagons in like-new condition. The only way in before was to climb over the beaters on front of the wagon. However, using a door on back is a lot safer.

“The 30-in. wide, 34-in. high door swings in and up and was made by cutting a hole on back of the wooden wagon and adding a hinge on top. Strips of flat steel were used to make a 2-in. wide frame that’s bolted around the entire door. The frame acts as a ‘stop’ to keep the door from coming back too far and allowing silage to spill out. Bolt-type latches at the bottom corners of the doors keep them secure. A handle at the middle of the door allows it to be grabbed and pulled shut.”

From the archive · Full text
Reader shop tip

Veryl Reiler

Veryl Reiler, Carlinville, Ill.

Veryl bought a metal desk for a bargain price and brought it to his shop. He put the desk on caster wheels so he can roll it easily around his shop. Miscellaneous parts and equipment can be stored in the drawers. Makes a handy mobile work table that he uses all the time. Veryl points out that you can often pick up old metal desks for nothing, or just a few bucks.”

From the archive · Full text
Reader shop tip 1 of 3

Robert Dunton

Individual tip 1 of 3 from this reader’s published contribution.
Robert Dunton, Topeka, Ill.

Robert found a good use for salvaged plastic elevator buckets. Unlike the old metal buckets, the plastic ones are light in color which makes it easier to spot needed items inside because of the way the light hits them.

Robert mounted a couple rows of buckets on an A-shaped plywood frame, with buckets on each side. He put caster wheels under the A-frame to roll it around the shop. He also mounts the elevator buckets on the shop wall.

From the archive · Full text
Reader shop tip 2 of 3

Robert Dunton

Individual tip 2 of 3 from this reader’s published contribution.
Robert Dunton, Topeka, Ill.

Robert had a problem with his dump auger, which originally had just two wheels. To make it easier to maneuver into place when unloading grain, he added caster wheels to the front and back end of the hopper.

From the archive · Full text
Reader shop tip 3 of 3

Robert Dunton

Individual tip 3 of 3 from this reader’s published contribution.
Robert Dunton, Topeka, Ill.

He also made a full-size wood cover to go over the top of the hopper. There are two handles on top of the cover to lift it off.

From the archive · Full text
Reader shop tip

Tim Hays

Tim Hays, Decatur, Ill.

For precise drilling, Tim salvaged a cross slide from a lathe and bolted it to the base of a drill press. The cross slide has its own small vise for holding metal parts precisely. Then, using left and right cranks, you can get absolute accuracy when drilling.

From the archive · Full text
Reader shop tip

Ed Dillard

Ed Dillard, Dade City, Fla.

“I plugged a leaking fuel tank on a jeep with JB Weld. It worked very well, and saved a lot because a replacement tank would have been expensive.”

From the archive · Full text
Reader shop tip

Jerry Hessman

Jerry Hessman, Dodge City, Kan.

“I was having problems keeping wheel bearings from wearing out on my New Holland side delivery rakes until I drilled and installed grease zerks in each hub. Now I grease them as often as I grease the other bearings on the rakes. No more wheel bearing problems.”

From the archive · Full text
Reader shop tip

Bill Reeks

Bill Reeks, Cromwell, Ky.

“I made this welding table from scrap steel. The top is 1/ 4-in. steel plate measuring 48 by 61 in. with “T” iron braces underneath for added strength. Legs and frame are made from 2-in. dia. pipe. I move it with a floor jack, lifting one end of the table. The legs on the other end are fitted with two 4-in. steel wheels. A lower shelf holds a variety of short materials and welding rods. This is a heavy-duty table that’s easy to move around.”

Shop feature stories

From the archive · Full text
Feature story

Simple Modification Boosts Air Conditioning On Cat Challenger

Featured source:

Orlin Schanz boosted performance of the air conditioner in his 1975 Cat Challenger by making a simple modification using a piece of pvc pipe.

“It improves performance 100 percent,” says Schanz, who came up with the idea after several years of sweltering heat inside the cab of his Challenger.

The idea is to recirculate air from inside the cab to the air conditioner, rather than continuously bringing in outside air.

“It lets you cool down air that is 70° rather than air from under the hood that’s 195°. And the way I did it, the recirculated air is filtered.”

He used a piece of 2-in. dia. plastic pipe fitted with threaded end couplers and nuts. He fitted the pipe into holes cut into the bottom of the air conditioner unit, just below the filter, and in the firewall of the cab. Then he simply taped over the air intake louvers on the side of the air conditioner so air must be drawn in through the pipe.

Contact: FARM SHOW Followup, Orlin Schanz, 80417 Ave., Langdon, N.Dak. 58249 (ph 701 256-2878).

From the archive · Full text
Feature story

Hand Clutch Makes Farmall M Easier To Use

Featured source:

Robert Dunton, Topeka, Ill., uses his vintage Farmall M for a lot of pto work. To keep from having to get on and off every time he needs to engage the pto, he installed a hand clutch that can be engaged from the ground. There’s a pivoting lever at back and a bar that runs up to the clutch pedal. The bar simply affixes it to bolts on both the lever and the pedal.

To use a hand clutch like this one, Dunton says you must be certain to have all guards in place on the pto.

From the archive · Full text
Feature story

New Manifolds For Old Engines

Featured source:

If you or your parts dealer are having trouble finding the right manifold for an older engine, try Vinson Tractor Co., Murray, Kentucky.

The company is one of the nation’s largest replacement manifold makers. It manufactures manifolds for Massey Ferguson, John Deere, Ford, Allis Chalmers, International Harvester, Oliver, and many others. They make both farm and industrial equipment manifolds. All are based on OEM specs and about 75% of what they sell is considered original equipment.

Their biggest sellers are for Farmall M and Allis Chalmers WD series engines. Much of what they make and sell is no longer available from the engine maker. While they don’t have every out-of-stock manifold, they are continually adding to their line. They have dealers throughout the U.S. and prefer to sell through them when possible. Many of their dealers are independent repair shops. Contact the company for product availability or to find a dealer in your area.

Contact: FARM SHOW Followup, Stan or Steve Downs, Vinson Tractor Co., 1935 State Rt. 94 E., Murray, Ky. 42071 (ph 800 443-8099; fax 270 753-5380).

From the archive · Full text
Feature story

Professional Quality, DC-Powered Impact Wrench

Featured source:

“It provides the power and reliability of an air impact wrench, but with the convenience of DC power,” says Lyndol Hollingsworth, inventor and manufacturer of what he calls “the most exciting new development in professional quality shop tools in years.”

Hollingsworth was a Snap-On Tools dealer for 15 years and says the most common complaint he heard from farmers, ranchers, tire service people, and others was the hassle of hauling air compressors – along with generators or gas motors – to the field to power air-driven tools. FARM SHOW featured Hollingsworth’s first prototype eight years ago (Vol. 17, No. 6). After years of research and development, he recently put the heavy-duty tools on the market.

The 1 1/2-in. drive impact wrench comes with a rechargeable battery pack that’s permanently attached, and an automatic battery charger. Recharge time is two to four hours. It even has an onboard work light for faster, safer nighttime use. Maximum torque of the heavy-duty tool is 45 ft.-lbs. The unit is compact enough to fit inside a 5-gal. canvas bucket or behind the seat of a pickup.

“Fully charged, our DC impact wrench will run for many hours of constant use before it needs recharging,” says Hollingsworth.

“It can do a full day’s work for such jobs as changing tires, drilling holes in wooden fence posts, or putting lag screws in a deck. It sells for $1,299 plus S&H which may seem high at first. However, when you consider the cost of buying and maintaining a compressor, along with generators or gas motors as well as cords and a separate impact wrench, it compares favorably. Also, it doesn’t require any maintenance and you don’t have to haul anything else with you.”

The wrench weighs 8 1/2 lbs. while the battery weighs 21 lbs. Both the wrench and battery come with grab handles for easy handling and portability.

Contact: FARM SHOW Followup, DC Power Equipment, LLC, 3007 Longhorn Blvd., Suite 113, Austin, Texas 78758 (ph 888 588-3545 or 512 835-9511; fax 512 836-9025; Website: www.dcimpact.com).

From the archive · Full text
Feature story

Where To Buy All Kinds Of Control Cables

Featured source:

If you need a control cables for a restoration project or just an overhaul, Ontario Control Cables either has what you need or will custom make one.

The company, based in Toronto, makes control cables for accelerators, throttles, brakes, clutches, hydrostats, PTOs, spool valves, and anything else that relies on either a push-pull cable or a pull-only cable to get the job done.

Company spokesman Gord Fram says most of the company’s cables are sold through dealers, but adds, “About 25 percent of our business is direct to farmers. Any-body can call us for price quotes on ready-made or custom length cables. Our prices are usually around 50 percent less than original equipment cables from dealers.”

While the buyer pays the shipping, Fram says most cables can be shipped for $6 or $8 just about anywhere in Ontario, with shipping a bit higher to the rest of Canada or the U.S. They accept VISA, MasterCard and American Express cards and offer same day shipping on orders received by noon.

Contact: FARM SHOW Followup, Ontario Control Cables, 33 Comstock Road, Scarborough, Ontario, Canada M2L 2G6 (ph 416 755-5440; fax 416 755-0377; E-mail: [email protected]).

From the archive · Full text
Feature story

Three-Headed Wrench Saves Time And Space

Featured source:

On a rainy day last fall when it was too wet to work outside, Robert Lamczyk, Ashley, Ill., found himself confined to his shop.

“We didn’t have a lot to do, and I happened to notice I’d left three open-end wrenches out on my workbench,” he says.

The 1/2-in., a 9/16-in., and 5/8-in. wrenches were lying on the bench because they were the three wrenches Lamczyk used most often. As he looked at them lying on the bench, it occurred to him that he could save time and space if he had just one wrench with all three heads on it.

With his chop saw and a welder, it didn’t take long to remake the three old wrenches.

“The handle is actually longer than on a regular wrench,” he says.

“I put the 5/8-in. head on one end of the handle and the other two in a Y on the other end.

“That was about three months ago. It’s really been handy since then,” he says.

In fact, its so handy he’s started the paperwork to patent the idea and make a full set of three-headed wrenches, to fit bolts from 3/8 in. up to 1 in. in size. Contact: FARM SHOW Followup, Robert Lamczyk, 8253 Tucker Road, Ashley, Ill. 62808 (ph 618 485-6630; E-mail: [email protected])

From the archive · Full text
Feature story

They Specialize In Pto Parts

Featured source:

Bauman Manufacturing, Ltd., Hawkesville, Ontario, specializes in pto parts, both metric and English. In addition to OEM parts for most equipment, Charles Bauman, manager, says they have a fully equipped machine shop where they can make nearly anything.

So if you need something for an antique or collectable, or just an older machine that’s no longer available from the manufacturer, give them a call.

They also have roller chain for most applications and conveyor chains, either stock or custom-made.

Bauman Manufacturing sells through dealers and direct to farmers and repair shops. The company promises low prices, particularly on roller and conveyor chains.

Contact: FARM SHOW Followup, Charles Bauman or Brian Burnes, Bauman Manufacturing, Ltd., P.O. Box 79, Hawkesville, ON N0B 1X0 (ph 519 699-4333; FAX: 519 699-5571; email: [email protected]; Internet: www.baumanmfg.com).

From the archive · Full text
Feature story

Durable Alternators Built To Survive Dirty Air

Featured source:

If you’ve ever had tractor alternator problems caused by dirt, dust, straw, chaff, etc., Buzz Equipment, Perryton, Texas, may have a solution for you.

Frank Buzzard, owner of Buzz Equipment, has designed a special alternator, the Buzzanator, that fits most applications for farm and industry. Buzzanator alternators are designed for peak performance under the toughest conditions.

“They have a front fan that draws large volumes of air through the alternator (from the rear to the front). A specially designed rear fan throws straw, CRP grass, dirt and other trash away from the alternator. This eliminates choking and allows clean air to flow throughout the alternator for cooler running,” Buzzard says.

Buzz Equipment makes several versions of the Buzzanator. All feature Delco-style one-wire hookup. If the company doesn’t have what you need, Buzzard says they can make it for you.

Contact: FARM SHOW Followup, Buzz Equipment, Inc., Box 1094, 17 S.E. 12th, Perryton, Texas 79070 (ph 800 762-9641 or 806 435-2441; E-mail: [email protected]; Web site: www.buzzequipment.com).

From the archive · Full text
Feature story

Railroad Wheels Make Ideal Hoist Carrier

Featured source:

Railroad-type wheels off an old brick cart from a factory kiln make ideal carrier wheels for an overhead chain hoist, says Allen Vinyard who uses two sets of wheels in his shop to easily move his hoist around.

“I used a roll-around floor crane to pull engines before, but I always had to clear a path so I could move it,” says the rural Hillview, Ill., machinist.

Two carriers are made from 3 by 6-in. rectangular tubing. Each is fitted with two of the 12-in. dia. wheels. Tracks were mounted on the outside walls of the shop. A 26-ft. I-beam runs between the rolling carriers. A chain hoist rolls back and forth on the I-beam.

Contact: FARM SHOW Followup, Allen Vinyard, R.R. 1, Box 129, Hillview, Ill. 62050 (ph 217 927-4289).

From the archive · Full text
Feature story

Fuel Tank Sand Blasting Cabinet

Featured source:

“We do custom painting and sand blasting of tractors, forklifts, and other equipment. We recently bought a big commercial sand blaster for our work. My son said he thought we needed another sand blaster for doing small stuff. So we made our own out of a 300-gal. diesel fuel tank, a cheap commercial pistol-type siphon blast gun, and a shop vac,” says Skip Kirkland of Mahomet, Ill.

Kirkland cut the tank stand’s legs down to 2 ft. and fitted them with caster wheels. A 1 by 2-ft. window was cut into one side along with a pair of 7-in. dia. access holes, spaced 16 in. apart. He fitted the holes with lengths of inner tubing to act as protective gloves.

On one end of the tank he cut out a 2-ft. sq. hole and mounted a hinged plywood door over it to serve as an access door. A large metal shelf at the opposite end supports a standard electric-powered shop vac that’s used to suck dust out of the tank. The vac’s hose is inserted through a fill hole on top of the tank. The air-powered siphon blast gun is inside the tank and is hooked up to a big 10 hp, 3-phase, electric-powered air compressor. A steel pipe runs from the siphon blast gun through the end of the tank and down into a bucket of sand that mounts on a second shelf below the shop vac. When Kirkland pulls the trigger on the siphon blast gun, sand is sucked up out of the bucket and is blown out.

A water filter/regulator mounted on one side of the tank is used to catch any moisture in the air compressor line.

“It works great and can be easily moved around our shop,” says Kirkland.

“To operate the sand blasting cabinet, we simply flip a switch on the compressor. A 4-ft. long fluorescent shop light hangs inside the tank to provide light,” notes Kirkland.

Contact: FARM SHOW Followup, Skip Kirkland, 19 CR 2150 N, Mahomet, Ill. 61853 (ph 217 586-6121).

From the archive · Full text
Feature story

Another Washing Machine Sand Blaster

Featured source:

Last issue we showed you a sand blaster made from an old washing machine cabinet (Vol. 24, No. 6). Tim Hays, Decatur, Ill., also built a sand blaster using a washing machine cabinet, but he took a different approach.

The cabinet sets sideways on top of an angled hopper. Hays cut two round holes in the side for hand access and installed an slanted window at eye level for good viewing. The window has a replaceable plastic liner to keep it from becoming sand pitted.

Hays hinged the old front of the washing machine so the entire panel hinges out for easy access to the inside of the cabinet.

To clean a part, Hays reaches inside to hold a blasting gun. A conventional air compressor supplies air to the gun through a regulator on the side of the hopper. Hays generally runs it at 40 to 50 psi. Sand is picked up by vacuum and then blown out the gun, then falls back to the bottom of the hopper.

Contact: FARM SHOW Followup, Tim Hays, Decatur, Ill. (ph 217 877-2209).