Spencer Turrentine
“This is my solution for carrying my chainsaw on my Gehl skid steer. My carrier also…
717 shop tips and stories · page 1 of 12, newest issues first.
“This is my solution for carrying my chainsaw on my Gehl skid steer. My carrier also…
“When splitting or having a hydraulic or oil line open, wrap aluminum foil around the line…
“To keep oil containers clean, store them in a 5-gal. bucket with a lid.”…
“In Vol. 49, No. 3, Rick Nudd shared a tip for using a box, especially open-front…
“Cargo straps are a total pain. So I took a wall hook rack and made a…
“A paint bucket used as a stool helps you keep a steady hand while working at…
“Taping a nail to the clip on a test light makes a good handle and is…
“Screwing a piece of auto brake line onto an air hose blower makes a very precise…
“Flat cookie sheets with curved sides from thrift stores make good trays for sorting items. I…
“Old bolt bins make handy storage for sockets (metric and ASAE). It’s not original, but it’s…
“Tired of sorting through loose wrenches, I used a large carabiner for 9/16 to 3/4-in. wrenches and a medium-sized one for 1/2-in. and smaller wrenches. It’s easy to remove them for use.”
Read the complete tip →“I use an old fold-up ping-pong table in my shop as a large parts and tool storage table when working on equipment. I can roll the table to where I’m working, spread out my old and new parts…
Read the complete tip →Dale Freeman doesn’t believe in wasted space. When he found room under his backhoe seat for a cooler, he put it to use. As with his chainsaw holders (Vol. 50, No. 3), he used a receiver hitch mount…
Read the complete story →“In retirement, it seems I have more projects than time. One recurring problem is remembering where I left a specialty tool or piece of equipment. Recently, I couldn’t find my cordless drill (again). After unsuccessfully looking in the…
Read the complete tip →“Battery cables slipping out of the clamp is a common problem. No cable means no battery charge. Try stripping extra wire and putting a bend on the end. Allow plenty of extra stripped wire.
Read the complete tip →“Take a mushroom box (or other small container) and put a magnet inside to keep small steel bits from spilling or getting lost. It can be stored at any angle as needed. It works great under the truck.
Read the complete tip →“Before sorting items on a bench, lay a towel down and place a 4 by 4 near the edge. No more small bits falling off and getting lost, and the towel lets you pour them back into the…
Read the complete tip →“For many of us, finding the tool we need can be impossible. Try taking the tools you seldom use and store them separately.”
Read the complete tip →“Tractor steps and running boards can be very slippery in winter when snow gets on them. After a couple of slips that could’ve been worse than they were, I decided to put some 1/4 by 1-in. bolts through…
Read the complete tip →“The rack from a buck makes a nice place to hang miscellaneous stuff.”
Read the complete tip →Nylon block chainsaw holders keep Dale Freeman’s chainsaws safe and secure. Modified receiver hitches mounted to the subframe of his tractor-mounted backhoe make chainsaws easy to access whenever needed. One hitch even serves double duty, holding a box…
Read the complete story →“Moving my auxiliary diesel fuel tank in and out of my truck bed with forks can be tricky. It came with angle-iron pieces at each end and along the sides of the tank. I bolted a piece of…
Read the complete tip →Leonard Wranosky converted old Baker scaffolding into a rolling storage unit. The scaffolding is only 29 1/2-in. wide and easily adjustable. It includes lockable casters and can be stacked.
Read the complete story →“We needed a better way to store planter plates, so we built this simple wall-mounted rack. Longtime friend and employee Mardy Dosland came up with the idea of using conduit and lids from 5-gal. pails.
Read the complete tip →“An easy way to manage zip ties is to store them in a scrap piece of pipe and hold them in place with a rubber band or, for better durability, a piece of shock cord. Individual ties can…
Read the complete tip →“Two 5-gal. buckets, plywood and foam from a seat cushion make a quick, comfortable bench for working while lying on your back.
Read the complete tip →“If you’re looking for more stable storage, glue a piece of wood to a jar or can. A larger piece of wood (maybe 2 by 6) works better for heavier items.
Read the complete tip →“A toothpick trimmed square is really good for fine-touch glue application.”
Read the complete tip →“Putting a cable tie on a pen or pencil makes it easier to pick up with gloves on or with arthritic hands.”
Read the complete tip →Rylan Steiner of Dalton, Ohio, makes and sells 3D-printed, Deere-compatible cup holders at his print shop on eBay. Each cup holder is designed to mount on the fender of a Sound Guard cab.
Read the complete story →Retired farmer Brian Haubrich enjoyed planning and developing new ideas while he was still actively farming. His ideas have been featured in FARM SHOW several times over the years, and his shop tool tree was featured in Vol.…
Read the complete story →“I built roll-around frames for all my woodworking equipment with screw-down locks to secure them in place, but I can move them when needed.”
Read the complete tip →“We began to notice after every drive to work or every adventure, whatever gear we carried in our truck beds was all over the place, tangled and sometimes even broken. We were tired of wasting time reorganizing or…
Read the complete story →“A clamp and a washer can be used to prevent a cut from dropping down and splitting. This works for bigger stuff using a piece of wood.
Read the complete tip →“Fold a piece of barrier tape into a repair manual you use often. Label if needed. It saves a lot of searching.
Read the complete tip →“Rubber bungee cords, hooked where convenient, make great, easy-to-use hangers for cords and hoses. Just attach the bottom hook to the top hook.
Read the complete tip →“These socket hangers are meant to be screwed into a wall. If you use a toolbox like I do, they often slide off and get lost. The fix is to add a small bolt, pointed upward, at each…
Read the complete tip →“To ground a vehicle battery to the frame, connect the negative terminal of the battery to the vehicle’s frame using a wrench and metal clamp, making sure the connection is tight and free of corrosion. This allows the…
Read the complete tip →“Store a 4 by 4 and a plank behind the seat until needed. Use them for parking on a hill or changing a tire.”
Read the complete tip →Rich Meyer, inventor of The Tool Swing, aims to improve the functionality of your workbench. This specially designed workshop aid quickly and easily swings up a vise, bench grinder, sander, chop saw or other tool, then swiftly unlatches…
Read the complete story →“I’ve made a couple of mobile workbenches from old gas grills. First, I removed the grill. The cart had a frame and a nice cabinet. I used an old solid-core door on top to make a mobile workbench.…
Read the complete tip →Dexter Brahn has made his shop vice more useful by adding additional tools and storage to keep things close by when working.
Read the complete story →Drawing from over 20 years of hunting experience and a career as an electrical lineman, Chris Rodgers invented a handy carry-around tool.
Read the complete story →If you’re looking for a quick and easy way to store air tools in your shop, Air Wrangler modular locking pneumatic holders may do the trick. The 1/4-in. quick-connect plug patent-pending design locks tools in automatically.
Read the complete story →Gary Swensen, Yankton, S.D.: “I shared in modifying a one-ton pickup box and rear frame into a field trailer. I’d mounted an 80-gal. propane tank to the tongue to serve as a high-capacity air supply. Recently, I made…
Read the complete story →Socket Straps can keep wrenches, sockets, screwdrivers and pliers, as well as nuts, bolts and screws, in place. The magnetic strips come in various sizes and feature powerful magnets.
Read the complete story →The Stupid Car Tray provides a stable, flat surface for various tasks.
Read the complete story →Unlike traditional ratchet straps, KwikFeed straps are designed with a unique ratchet mechanism that allows for quicker tightening and release. This can save time, whether hauling hay, securing equipment on a trailer, or keeping materials organized on the…
Read the complete story →“I put ratchet straps inside PVC pipe to keep them untangled.”
Read the complete tip →“Like many readers, FARM SHOW is my favorite publication. I’m glad to see I’m not the only one who braids baling twine. I built a cargo net with mine.
Read the complete tip →“Acetone and power steering fluid (50/50) make great penetrating oil.
Read the complete tip →Heating the nut and touching it with a candle also works to loosen a stuck nut or bolt.
Read the complete tip →“An iron rake head attached to the wall holds box end wrenches and sockets. Save the broken handle; they make great stakes.
Read the complete tip →“Soak tools that are rusted shut in water.
Read the complete tip →“I found that a 2-in. eye bolt fastened to the hitch of my lawn tractor let me pull my utility trailer easily. I never bent it, even with the trailer loaded.
Read the complete tip →“Cutting grooves in your mower blade (like a Ginsu knife) doesn’t make for a better cut; it only wears the blade faster.
Read the complete tip →“I beg everyone that uses old motor oil in their saws or as a stain to stop it. You can’t filter out dissolved solids. Burnt oil is carcinogenic. Dispose of it correctly.”
Read the complete tip →“I had trouble lining up the hitch pin on my receiver. So, I welded a stop block on the top of my hitch. I first put the pin in and then welded a 1/4-in. steel block on the…
Read the complete tip →“I always carry my pintle hitch with me in my truck. But it was constantly sliding around in the truck bed. I came up with the idea of mounting it under the truck behind the bumper. I welded…
Read the complete tip →“I pick up lots of equipment with my skid steer forks, but I was always afraid that my lifting straps or chains would slip off the end of my forks. I drilled a 1/2-in. hole near the end…
Read the complete tip →