Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW

Tools

5957 shop tips and stories · page 1 of 100, newest issues first.

From the archive · Full text
Reader shop tip 1 of 2

Don Wooley

Individual tip 1 of 2 from this reader’s published contribution.
Don Wooley, Lawton, Okla.

“Lifting heavy equipment (generators, pumps, mowers, etc.) is always difficult or impossible. I mounted a 2 by 4 to a heavy crossbeam in the structure of the attic and extended it through the ceiling into the workshop. I…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Don Wooley

Individual tip 2 of 2 from this reader’s published contribution.
Don Wooley, Lawton, Okla.

“My 4-car attached garage has never seen a car as it’s my workshop. I installed my tall 60-gal. air compressor in the attic above. I dropped the drain through the ceiling into a reservoir with the drain at…

Read the complete tip →
From the archive · Full text
Reader shop tip

David Schlosser

David Schlosser, Edgeley, N.D.

“I use a plastic syringe to apply gasket adhesive in tight places. This allows better control over the tube it comes in, and you have the syringe tip to reach into tight places. It’s also easier to apply…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 3

Tim Weaver

Individual tip 2 of 3 from this reader’s published contribution.
Tim Weaver, Lititz, Pa.

“If you have a bent and twisted piece of sheet metal, the fastest way to straighten it is to use two bars of metal in the press brake or shop press and use those to straighten it.

Read the complete tip →
From the archive · Full text
Reader shop tip 3 of 3

Tim Weaver

Individual tip 3 of 3 from this reader’s published contribution.
Tim Weaver, Lititz, Pa.

“We recently put up a 1-ton bridge crane in our shop, and it makes handling parts so much better.”

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 3

Cal Miner

Individual tip 1 of 3 from this reader’s published contribution.
Cal Miner, Willmar, Minn.

“Angle grinders of all sizes need to be periodically opened up and regreased or lubed. The grease that comes with them is very thick and cakes in the housing, leaving no lubrication on the spindle and gears.

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 3

Cal Miner

Individual tip 2 of 3 from this reader’s published contribution.
Cal Miner, Willmar, Minn.

“I had a dark area in my shop where it was hard to see my tools. I bought a battery-powered twin light with a motion sensor. The motion sensitivity and duration can be adjusted.

Read the complete tip →
From the archive · Full text
Reader shop tip 3 of 3

Cal Miner

Individual tip 3 of 3 from this reader’s published contribution.
Cal Miner, Willmar, Minn.

“Sometimes, it can be hard to loosen a nut. This photo shows the friction-drive wheel on a rear-engine Snapper rider. To keep the pry bar on the studs while loosening the nuts, reverse a flange nut and turn…

Read the complete tip →
From the archive · Full text
Reader shop tip

LeRoy Ellis

LeRoy Ellis, Reliance, S.D.

“Having a rotary tool in your shop is very handy. There are numerous grinding and shaping bits. It fits into small places that larger grinders can’t reach. A diamond grinding point works well for cutting super-hard metal. I’ve…

Read the complete tip →
From the archive · Full text
Reader shop tip 5 of 6

John Rochester

Individual tip 5 of 6 from this reader’s published contribution.
John Rochester, Charlotte, N.C.

“To ground a vehicle battery to the frame, connect the negative terminal of the battery to the vehicle’s frame using a wrench and metal clamp, making sure the connection is tight and free of corrosion. This allows the…

Read the complete tip →