Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW

Tools

5957 shop tips and stories · page 95 of 100, newest issues first.

From the archive · Full text
Reader shop tip 1 of 3

Clark Dysle

Individual tip 1 of 3 from this reader’s published contribution.
Clark Dysle, Scio, Ore.

“Our 1987 Ford 250 diesel pickup is strong and runs good but the hydraulic clutch is poorly engineered. The master and slave cylinders are made out of plastic and wear out about every 50,000 miles. The cost to…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 3

Clark Dysle

Individual tip 2 of 3 from this reader’s published contribution.
Clark Dysle, Scio, Ore.

“When welding thin steel I use a stainless rod with A.C. power. It seems to flow without blowing a hole in the thin metal. It’s much faster than gas welding and less heat is used, presenting damage to…

Read the complete tip →
From the archive · Full text
Reader shop tip 3 of 3

Clark Dysle

Individual tip 3 of 3 from this reader’s published contribution.
Clark Dysle, Scio, Ore.

“To safely change the rear transmission on my 10-yard dump truck, I built a wood frame that goes just behind the cab, and I hung a chain and come-along from both the wood frame and from the hydraulic…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Leonard J. Arenz

Individual tip 1 of 2 from this reader’s published contribution.
Leonard J. Arenz, Streator, Ill.

“The drive chain on the rotary screen on the radiator on my 510 Massey combine kept breaking. I read an article in FARM SHOW about a farmer who had the same problem. I called the man and did…

Read the complete tip →
From the archive · Full text
Reader shop tip

Roland Beckmeyer

Roland Beckmeyer, Hoyleton, Ill.

When Roland decided to add flashing safety lights to the back of his machinery, he decided to use battery-operated units rather than running wire to operate 12-volt lights. This way he can transfer one set of lights between…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Andy R. Hodges

Individual tip 1 of 2 from this reader’s published contribution.
Andy R. Hodges, Galax, Va.

“One tough maintenance job I’ve got is putting bearings on the rollers of a New Holland Haybine. It’s extremely tough and time-consuming. I made it easier by using a torch to cut the old bearings off the shaft.

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 3

Chris Palmer

Individual tip 1 of 3 from this reader’s published contribution.
Chris Palmer, Enumclaw, Wash.

“I couldn’t unbolt a tie rod off the steering arm on my Massey 65. My 3/4-in. Craftsman expandable wrench broke but my Stanley Proto wrench took it off with a 3-ft. piece of pipe on it. The Proto…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Don Booth

Individual tip 1 of 2 from this reader’s published contribution.
Don Booth, Leoville, Sask.

“I had a problem with erratic operation of the Powershift on my 1986 Case-IH 4494 tractor. The dealer couldn’t fix it and the company service rep was no help either. I finally found the problem myself - bad…

Read the complete tip →
From the archive · Full text
Reader shop tip

John Cernius

John Cernius, Climax, Mich.

“I break beads on tractor tires by using down pressure from my backhoe stabilizer arm. The bucket is positioned to hold the wheel flat on the ground and the stabilizer is used to unseat the bead. It’s safe…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

John Hoegl

Individual tip 1 of 2 from this reader’s published contribution.
John Hoegl, Lloydminster, Sask.

“We installed a hand-operated winch on the left side of our two Deere 8820 combines so we can raise or lower the straw chopper by simply turning a crank. We lower the chopper whenever we want to drop…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

John Hoegl

Individual tip 2 of 2 from this reader’s published contribution.
John Hoegl, Lloydminster, Sask.

“When using our Deere 535 auto-wrap round baler we had a problem getting enough twine wraps on the left side of the bale, especially when we had to bale dry straw. It would compress, allowing the twine to…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Tim Beirnes

Individual tip 1 of 2 from this reader’s published contribution.
Tim Beirnes, Cambridge, Ontario

“The wagon hitch on my Massey-Ferguson 124 baler was built too light and often broke. The hitch was made up of a 2-in. dia. steel pipe that slid inside a 2 1/4-in. (inside dia.) light wall sleeve and…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Tim Beirnes

Individual tip 2 of 2 from this reader’s published contribution.
Tim Beirnes, Cambridge, Ontario

“We broke a knuckle on the baler’s pto shaft on a Saturday night. A new yoke would have cost about $100 and my dealer was closed for business on Sunday. I solved the problem by borrowing the pto…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Tom Graham

Individual tip 1 of 2 from this reader’s published contribution.
Tom Graham, Henderson, Minn.

“Instead of removing the straw chopper on Massey Ferguson 300, 410 and 510 combines when switching from corn to beans, I remove the front two bolts and hinge the chopper down on the back two bolts, then put…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Tom Graham

Individual tip 2 of 2 from this reader’s published contribution.
Tom Graham, Henderson, Minn.

“I’ve discovered that auto salvage yards that wreck late model cars have used anti-freeze available. I bought a 55-gal. drum for $25 and use it in all my older cars, truck and farm machinery. Works as good as…

Read the complete tip →