Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW

Tools

5957 shop tips and stories · page 65 of 100, newest issues first.

From the archive · Full text
Reader shop tip 1 of 2

Noel Hicks

Individual tip 1 of 2 from this reader’s published contribution.
Noel Hicks, Palmyra, Ill.

He took an old foot-powered grindstone, built a stand for it and motorized the grindstone. It works a lot better than modern high-speed grinders because it grinds slowly and doesn’t burn the edges as fast, says Hicks.

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Leon Bailey

Individual tip 1 of 2 from this reader’s published contribution.
Leon Bailey, Elkton, Virg.

“I broke the cable inside the shaft on my Weedeater trimmer. A new cable would have been expensive so I welded mine using a mig welder. I just welded a little bit at a time so it wouldn’t…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Marvin Kroontje

Individual tip 1 of 2 from this reader’s published contribution.
Marvin Kroontje, Magnolia, Minn.

“I use a 1/2-in. dia., 3-ft. length of galvanized water pipe - with the last foot curved - to tighten belts on vehicle alternators, power steering units and air conditioning units. It makes a great pry bar once…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Marvin Kroontje

Individual tip 2 of 2 from this reader’s published contribution.
Marvin Kroontje, Magnolia, Minn.

“I wanted to mulch leaves during the fall when cutting my lawn with my Big Mo riding mower, so I duct taped an L-shaped chunk of tin over the mower’s discharge chute opening. The closed-off opening holds leaves…

Read the complete tip →
From the archive · Full text
Reader shop tip

Roger Kuntz

Roger Kuntz, K-Tech, 5251 County Road X, Grainfield, Kansas 67737 ph 785 673-5560

“My new blade plow leveling guide contains instructions designed to help farmers solve some technical problems with blade plows. I started working for Flex King in 1972 and served in research and development and as the head of…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Theodore Haugen

Individual tip 1 of 2 from this reader’s published contribution.
Theodore Haugen, Plummer, Minn.

“In a past issue of FARM SHOW there was a write-up by a person doing welding on cast iron using nickel rod. I’ve used that method for some time but on the last cast iron job I didn’t…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 5

Bill Reeks

Individual tip 2 of 5 from this reader’s published contribution.
Bill Reeks, Cromwell, Ky.

“Want an easy way to salvage the last few drops of motor oil from its container? Find a large bottle with a neck large enough for the neck of the 1-quart oil bottle to fit inside it and…

Read the complete tip →
From the archive · Full text
Reader shop tip 3 of 5

Bill Reeks

Individual tip 3 of 5 from this reader’s published contribution.
Bill Reeks, Cromwell, Ky.

“When I need a short piece of small wire I use a paper clip. They’re cheap, readily available, and provide the size you need when other sources aren’t there. A jumbo size clip will provide 6 3/8 in.…

Read the complete tip →
From the archive · Full text
Reader shop tip 4 of 5

Bill Reeks

Individual tip 4 of 5 from this reader’s published contribution.
Bill Reeks, Cromwell, Ky.

“Attaching a paper clip to the end of a roll of tape makes the tape end easy to find and use when needed. It saves time, frustration and tape, as some folks fold under the end ;of the…

Read the complete tip →
From the archive · Full text
Reader shop tip 5 of 5

Bill Reeks

Individual tip 5 of 5 from this reader’s published contribution.
Bill Reeks, Cromwell, Ky.

“To place a screw or nail into an inaccessible area where it’s difficult to hold, loop a string through a soda straw and around the screw or nail. Then hold the two ends of string and place the…

Read the complete tip →