From the archive · Full text
Reader shop tip
Joseph Palicka, Aitkin, Minn.
“I made a simple 6-terminal throw switch in order to raise and lower my truck-mounted snowplow blade. It allowed me to convert my 12-volt winch, which would only power up, to power down, also. The throw handle sides…
Read the complete tip →From the archive · Full text
Reader shop tip
Ken Scharabok, 1645 West blue Creek Road, Waverly, Tenn. 37185 (email
[email protected]): “I have made a tool that can replace several wrenches and a heavy-duty hammer. I forge down the end of the wrench to fit into the head before being welded in place for strength. I have one…
Read the complete tip →From the archive · Full text
Reader shop tip
Mark S. Yax, Solon, Ohio.
“The tubeless tire on my wheelbarrow had some dry rot which caused a bad seal. Every time I tried to use it, the tire had gone low on air, even though I might have filled it recently. To…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Randall L. Lacy, McHenry, Md.
“The skid plates on my Vicon disc mower were wearing out too fast. So I started welding inexpensive plate steel to the skid plates. They last much longer now.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Randall L. Lacy, McHenry, Md.
“I found a similar solution for a chain that kept breaking on me. The paddles on my Patz Barn Cleaner were weak at the links so I just removed the paddles and welded new links in their place.…
Read the complete tip →From the archive · Full text
Reader shop tip
Robert A. Pyle, Pickford, Mich.
“In tight spots where I need to use a nut, I pack the socket with grease to hold the nut while I move the socket into place. This stops it from falling out but allows me to tighten…
Read the complete tip →From the archive · Full text
Reader shop tip
Roger and Bruce Elliott, Montrose, Ill.
“We made a rolling support for the heavy pieces of machinery that are worked on in our shop. The roller is actually 6-in. pipe mounted on telescoping pieces of square piping. This allows it to adjust for height.…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Ian McConaghy’s White 2-105 front wheel assist tractor needed repair but the necessary part could not be located. So the Legal, Alberta man took things into his own hands, literally.
Read the complete story →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Cary Urka, Brethren, Mich.
“Pickup-mounted snow blades can be difficult to install. To make the job easier, I mount the blade on a pallet jack. I wheel the blade up to the pickup, then use the hand jack to raise the blade…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Cary Urka, Brethren, Mich.
“I use a shopping cart to haul my wire feed welder and acetylene tank around my shop. The welder rests on a metal shelf, and the tank mounts on brackets that attach to the cart. I widened the…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Cary Urka, Brethren, Mich.
“This 10-ft. wide stainless steel kitchen sink mounts along a wall inside the paint room in my shop and is used for mixing paint, storing paint guns, etc. Rinse material drains into an old paint thinner located under…
Read the complete tip →From the archive · Full text
Reader shop tip
Craig Froman, English, Ind.
“When the magneto goes dead on an old tractor, I convert the magneto to a distributor by using the coil and condenser from an old car, which I get cheap at a junkyard. I hook the distributor wires…
Read the complete tip →From the archive · Full text
Reader shop tip
George E. Adams, Sr., Williston, Fla.
“The old New Holland forage choppers have fan knives that are really hard to keep sharp and they have to be removed to be sharpened. Part of the problem is that you have to re-move the housing to…
Read the complete tip →From the archive · Full text
Reader shop tip
George R. Moser, Hardy, Va.
“Plastic wire spools - available free for the taking from motor or transformer shops - provide a neat and safe way to hang water/air hoses, extension cords, etc. The spools can be screwed directly to a wall or…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Jack W. Griffith, Euless, Texas
“I got tired of pumping my hand sprayer during long jobs. So I decided to eliminate pumping by using air pressure. I installed a tire valve and simply fill it up with a compressor. As long as I…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Jack W. Griffith, Euless, Texas
“Similarly, I needed a plastic carrying case to tote around a small oxy/acetylene torch. But the cheapest case I found still cost $70. Instead I decided to put it in a five-gallon bucket and it still had room…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Jim Relihan, Brunswick, Ga.
“To get more life out of a faucet seat, remove the seat and rub it back and forth on a metal file until the flaw is gone. You can more than double the life of a seat this…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Jim Relihan, Brunswick, Ga.
“A retractable extension cord made from an old vacuum cleaner cord mechanism gives me 25 ft. of cord for a drill.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Otto Mildner, Kingston, Ill.
“To make rusty tools look like new again, I simply soak them in white vinegar for two or three weeks. Then I use a brush to remove any leftover residue and shine up the tools.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Otto Mildner, Kingston, Ill.
When I’m done, I sometimes use the rust-colored liquid to stain furniture.
Read the complete tip →From the archive · Full text
Reader shop tip
Phillip L. White, Murfreesboro, Ark.
“My son and I welded chain hooks to the top of our front end loader bucket and hay fork. The hooks come in handy for all kinds of pulling and lifting jobs. We also welded a short length…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Steve Spiering, Milbank, S. Dak.
“Here’s an easy way to put threads all the way through lengths of pipe or square tubing. Use a woodworker’s dowling jig to make a centered, true pilot hole. Drill a hole and insert a nut. Weld around…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Steve Spiering, Milbank, S. Dak.
“My Volvo truck is equipped with two large oil filters. Whenever I change the oil, I have to lie on my back directly below both filters to remove them. I didn’t want hot oil splashing on my face…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Steve Spiering, Milbank, S. Dak.
“To cleanly bend light or medium gauge sheet metal without using a brake, I use a thin grinder blade and a guide to score a line halfway through the metal. After bending the metal to the desired position,…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
You can access any area of a big vehicle’s engine compartment easily and comfortably with this new, portable “caddy.”
Read the complete story →From the archive · Full text
Feature story
Featured source:
“Oliver is tradition in my family and was the tractor of choice for my father, grandfather, uncles and cousins. We worked on our own equipment,” says Steve Laue.
Read the complete story →From the archive · Full text
Reader shop tip
Bruce Graham, Tyler, Texas
“Not long ago I stripped out a thread where a flywheel bolts onto the crankshaft of an engine. I didn’t want to have to pull the engine again in order to fix the threads, but I was concerned…
Read the complete tip →From the archive · Full text
Reader shop tip
Elmer Pinkerton, Elmwood, Neb.
“Power grease guns are high on the want list of a lot of people. These units will save time right now, but cost you money in the long run because they will double your annual grease cost. And…
Read the complete tip →From the archive · Full text
Reader shop tip
Handy Chainsaw Transport, Town & Country Magazine
This idea was written up in a recent issue of Town & Country Magazine. A reader sent in a photo of a chainsaw sitting inside an old tire with a couple of cuts made in the sidewalls for…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
“If the wide front axle on your Deere tractor breaks, I can help you no matter what the tractor’s year or model,” says Ed Beem, Hornick, Iowa, who has been offering replacement wide front axles for more than…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Gene Kuyrkendall, Canyon Lake, Texas, re-stored a 1948 Allis Chalmers WD 45 tractor and wanted to mount an aftermarket front-end loader on it. But to make the loader fit he had to remove a belt pulley on one…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Clair Wilson has been salvaging and collecting parts and equipment from all kinds of places for a long time. When he first found a 22 by 5 1/2-ft. slab of steel that’s 1/2 in. thick at a burned…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Paul Begin was tired of hurting his hands when trying to dislodge stubborn nuts and bolts on older salvage equipment. He finally decided to make a big wrench that used a worm gear to loosen bolts even in…
Read the complete story →From the archive · Full text
Feature story
Featured source:
If you need parts for a Bobcat skid steer loader, you may want to contact Skid Steer Parts, Inc. in Hialeah, Fla.
Read the complete story →From the archive · Full text
Feature story
Featured source:
If you own a Ford, Chevrolet, or Dodge diesel pickup, you’ll be interested in this on-line source for diesel parts.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Imagine cutting in half the time it takes to change your engine oil, while eliminating most of the mess at the same time. That is just what the Fumoto Valve promises to do.
Read the complete story →From the archive · Full text
Reader shop tip
Bud Etzler, Motley, Minn.
“Three parts charcoal lighter fluid and one part automatic transmission fluid works good to free up frozen engines.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Cary Urka, Brethren, Mich.
“I built an inexpensive wood stove out of an old fuel barrel. I mounted the barrel on four metal legs, then cut a door into one end of the barrel and installed a baffle inside. A stovepipe chimney…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Cary Urka, Brethren, Mich.
“I wash all my equipment outside the shop using an Alcoa hot pressure washer that mounts inside my shop. The washer’s hose reel mounts about 3 ft. off the floor. I feed the hose out through a hole…
Read the complete tip →From the archive · Full text
Reader shop tip
Donald Bunch, Bunch Farm Services, Inc., Box 712, Aberdeen, Miss. 39730 ph 662 369-9570
“I like the idea of using tire sealants, but I often find that it’s not easy to get the sealant into the tire. To solve the problem I made this little device. It consists of a 12-in. length…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Douglas V. Spencer, Fenwick, W. Va.
“I couldn’t find any replacement grass seed tubes for my Massey Harris grain drill so I simply cut a cheap, plastic 1/2-in. dia. water hose to the proper length.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Douglas V. Spencer, Fenwick, W. Va.
“To keep a pencil handy at all times, I tape a clothes pin to the pencil and then clip it to the bill of my cap. The pencil is always there when I need it.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 4
Individual tip 1 of 4 from this reader’s published contribution.
Elmer Pinkerton, Elmwood, Neb.
“There are several suggestions around on how to remove the nut that holds the blade on push lawn mowers. Forget them all. An air impact wrench will bring that nut off in seconds without anything holding the blade.…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 4
Individual tip 2 of 4 from this reader’s published contribution.
Elmer Pinkerton, Elmwood, Neb.
“One of your readers suggested using two nuts as a gauge to sharpen drill bits. Fine idea, but it’s easier to use crazy glue to weld the nuts into one gauge.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 4
Individual tip 3 of 4 from this reader’s published contribution.
Elmer Pinkerton, Elmwood, Neb.
“I use 80-weight gear oil to seal the beads on all my tires. It works better than soap.
Read the complete tip →From the archive · Full text
Reader shop tip 4 of 4
Individual tip 4 of 4 from this reader’s published contribution.
Elmer Pinkerton, Elmwood, Neb.
“In a recent issue someone said he used a short length of pipe to protect tire valve stems from damage. I like this idea because you can safely leave a trailer in a hog lot without having to…
Read the complete tip →From the archive · Full text
Reader shop tip
Karl Rosendahl, Spring Grove, Minn.
“I came up with a simple way to find the causes of shorts in a car, pickup or tractor. I solder a wire to each end of a blown fuse and then connect a headlight bulb to the…
Read the complete tip →From the archive · Full text
Reader shop tip
Max Serr, Paul, Idaho
“Here in Idaho we use a lot of 8 and 12-in. dia. underground pipe for irrigation. Eventually, the bottom side of the pipe rusts out. To fix it, you have to cut an entrance hole through the top…
Read the complete tip →From the archive · Full text
Reader shop tip
Newell Franks, Kansas City, Mo.
“To make furnace cement, I just mix Portland cement and wood ashes in a 50-50 ratio.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Steve Spiering, 48594 Hwy. 158, Milbank, S. Dak. 57252 (ph 320 568-2246)
“The cable on my bin’s stirrator kept falling off. I had to put the cable back on up to four times a day, which got old. I solved the problem by welding on a shield off a rolling…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Steve Spiering, 48594 Hwy. 158, Milbank, S. Dak. 57252 (ph 320 568-2246)
“Our 7-in. dia., 55-ft. long, pto-driven grain auger wasn’t big enough to meet our needs any more, so I converted it to an electric-op-erated model to boost capacity. A 5 hp electric motor mounts on two lengths of…
Read the complete tip →From the archive · Full text
Reader shop tip
Tom Billingsly, Buckeye, Ariz
“Here’s an idea that a custom manure-hauling contractor came up with for his trucks with side-mounted gas tanks. He was working in extremely dusty, dirty conditions, hauling sludge onto cotton fields. The problem was that he had to…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Vic Smith, Parkville, Mo.
“While restoring my great grandfather’s old 2-row Ford planter, I found that some springs were old and rusted. To solve the problem I bought surplus spring kits at Tractor Supply. I treated some of the old and rusted…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Vic Smith, Parkville, Mo.
“Instead of buying expensive penetrating oil, I mix diesel fuel with baking soda. Works just as well.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Vic Smith, Parkville, Mo.
“I lined my shop walls with pegboard and mounted exhaust fans on them. The fans are hooked up to timers. They keep my shop well ventilated.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Bill Reeks, Cromwell, Ky.
“Lawn tractors usually get used only for mowing and maybe for towing a small cart or trailer. To make my new Sears Craftsman 17 1/2 hp riding mower more versatile, I removed the hood and installed a bumper…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Bill Reeks, Cromwell, Ky.
“To charge more than one battery at a time I line up the batteries so that the positive posts are aligned, and then use a vise grip to clamp a wire to all the positive posts. The negative…
Read the complete tip →