From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Douglas J. Hart, Bethel, Vt.
“My 1996 Lumbermate Bandmill was originally powered by a 20 hp Honda engine which ran too slow and was underpowered. I solved the problem by replacing the Honda with a Suzuki 3-cyl. fuel-injected, overhead cam, water-cooled gas engine.…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Douglas J. Hart, Bethel, Vt.
“To put up a low-cost building to work on my equipment during below zero weather, I sawed out some 2 by 4’s to frame up a gam-brel roof-style shop and then covered the frame with inexpensive blue tarps.…
Read the complete tip →From the archive · Full text
Reader shop tip
George Wissinger, Huntington, Ind.
He fixed a common problem on his 1963 New Holland 268 small square baler.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Hebert Wodtke, Loogootee, Ill.
“I replace farm wagon tires with used 16-in. pickup tires. I like tires with 8-ply or more. Rather than buy tubes, I use a liberal amount of talc seed lubricant in each tire and on each bias tube.…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Hebert Wodtke, Loogootee, Ill.
I install a grease zerk in the dust cap on each wagon wheel. It makes lubing wheels a much quicker job. In more than 40 years of farming, I’ve accumulated more than 23 grain wagons. Most of them…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Hebert Wodtke, Loogootee, Ill.
“I believe in preventative maintenance, so whenever a motor vehicle reaches 16 years of age I start checking prices for a replacement radiator even if there’s nothing wrong with the one I already have. In my opinion, a…
Read the complete tip →From the archive · Full text
Reader shop tip
Hy-Capacity Eng. & Mfg., Inc., Hwy.
169 S., Humboldt, Iowa 50548 (ph 800 247-1824 or 515 332-2125; www.hy-capacity.com)
Anyone who owns an Oliver/White 1650 or 1750 tractor will be interested in this company’s new clutch conversion kit. The tractor’s original clutch comes with a 3-lever Borg-Beck pressure plate with an I-bolt that tends to break prematurely.…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Mark Burrow, 11221 N. 100 th St., Altamont, Ill. 62411 ph 618 483-5598
Mark mounted a homemade reel on top of his air compressor, providing fast payout of the pressure hose and equally fast winding back up. He used a pair of old discs to make the reel, fashioning them into…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Mark Burrow, 11221 N. 100 th St., Altamont, Ill. 62411 ph 618 483-5598
He also came up with a unique way to transport gas welding tanks that makes use of an ordinary hand truck. He constructed a metal stand for the welding tank, leaving a bit of extra space below the…
Read the complete tip →From the archive · Full text
Reader shop tip
Posi Lock Puller, Inc., 805 Sunflower Ave., P.O. Box 246, Cooperstown, N. Dak. 58425 ph 800 533-5761 or 701 797-2600; www.posilock.com
This company recently introduced new Hold-Et magnetic vise clips that eliminate the need for an extra pair of hands when working with a vise. They also let you close the vise as tight as you want without damaging…
Read the complete tip →From the archive · Full text
Reader shop tip
Red Rock Mfg., 1117 Park Lane, Pella, Iowa 50219 (ph 641 780-1748; www.redrockmfg.com)
Anyone who owns a Ford 2N, 8N, or 9N tractor will be interested in this new combination gas cap and gauge that’s designed to replace the tractor’s original gas cap. These tractors don’t have gas gauges so it’s…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Wingfield Distributors, Inc., 4712 N. Cunningham Ave., Urbana, Ill. 61801 ph 800 637-6712; fax 217 643-7849; www.wingfields.com
This company offers a new screw-holding driver made in Germany. The design permits single-handed operation for starting a screw, allowing easier access in tight places. It allows you to place screws through holes or in hard-to-reach places without…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
When bush hogging tall, thick weeds, Paul Lowrance had trouble with the weed seeds shattering and getting sucked through the front grill of his tractor, clogging up the radiator.
Read the complete story →From the archive · Full text
Reader shop tip
Bradley Moore, Krypton, Ky.
“A reed valve on my small Sears compressor broke and no replacement was available. I made one from a feeler gauge leaf but it didn’t last very long. Then two years ago I made another one from a…
Read the complete tip →From the archive · Full text
Reader shop tip
Chris Kornkven, N6280 County P, Helenville, Wis. 53137 ph 920 699-2376)
“To help keep my shop clean, I needed some way to store metal stock or other lengths of odds and ends. I had some extra lengths of wire stock panels on hand. I cut down the panels and…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Chuck Golankiewicz, Pittsburgh, Penn.
“When Troy Bilt told me they couldn’t supply parts for my 33-in. mower, I had a local machine shop make parts and they work even better than the original ones.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Chuck Golankiewicz, Pittsburgh, Penn.
“The driveshafts on my Deere tracked snowblower rusted and froze up. After cleaning, I drilled and installed grease fittings to prevent further rusting.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Chuck Golankiewicz, Pittsburgh, Penn.
“Keep a supply of parts and belts as replacements. Stick to one brand to make it easier. I prefer Briggs & Stratton.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Jim Matthews, Saskatoon, Sask.
“To come up with a cheap tarp, I go to our local lumber yard and pick up pieces of plastic that are used to wrap lumber when it’s shipped. Normally, most lumber yards just throw this plastic away.…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Jim Matthews, Saskatoon, Sask.
“If you have a leak in a fuel tank or an engine cooling system, you can use a vacuum cleaner on the tank opening to create a good vacuum. (You might want to drain some coolant if it’s…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Jim Matthews, Saskatoon, Sask.
“If you have a small shed without any electricity and want to have light inside it, you can use a solar battery charger to power a light. You can buy these solar battery chargers cheap at Wal-Mart and…
Read the complete tip →From the archive · Full text
Reader shop tip
Rich Vink, Topeka, Kansas
“To provide better light inside my machine shed, I’ve mounted theater stage lights on the building’s trusses and aim the light beams down toward my farm equipment. It saves the hassle of using a drop light and also…
Read the complete tip →From the archive · Full text
Reader shop tip
Robert Ellis, High Hill, Mo.
“I designed this tool to loosen the belt that drives the pickup on older model Vermeer balers to make it easier to grease the bars at each end of the pickup. It saves a lot of skinned knuckles,”…
Read the complete tip →From the archive · Full text
Reader shop tip
Roger Kuntz, K-Tech, 5251 Co. Rd. X, Grainfield, Kansas 67737 ph 785 673- 5560
You can keep your wire welding gun close at hand with this new “magnetic base” welding gun holder.
Read the complete tip →From the archive · Full text
Reader shop tip
Steve Nelson, Winston-Salem, N.C.
“I had a problem with the 2-WD shift lever on my Kawasaki Mule. The lever wouldn’t re-lease until it really torqued up and made a big bang. The problem is the spring that re-turns the selector lever at…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Timothy Locke, Bremen, Ala.
“I had trouble leaving small walk-through gates open, so I attached screen door springs to them so they would close automatically.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Timothy Locke, Bremen, Ala.
“I have a small Yanmar tractor that’s light on front, so I melted old wheel weights into an iron skillet to make front weights that hold the front end down.”
Read the complete tip →From the archive · Full text
Feature story
Featured source:
When David Curtis took an early 1980’s Cadillac to a junk yard to scrap it, they wouldn’t take it because he didn’t have the title.
Read the complete story →From the archive · Full text
Feature story
Featured source:
A tiny new hydraulic jack can get into tight spots, yet it has an amazing lift capacity of five tons.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Since they retired, Lester Rose and his wife, Andrea, have lived on the road for the past 13 years with no permanent address (see re-lated story on page 39). In that time they learned that the hitch pulling…
Read the complete story →From the archive · Full text
Feature story
Featured source:
By modifying an old No. 5 hitch off an IH planter, Leonard Seltzer built a “lift boom” that makes it easy to do maintenance work on his riding mower. A 1-ton chain hoist does the lifting.
Read the complete story →From the archive · Full text
Feature story
Featured source:
“It provides me with a safe and easy way to clean the deck and sharpen the blades on my riding mower,” says Arnold Hussong, Okabena, Minn., who recently sent FARM SHOW photos of an electric-operated hoist his son…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Anyone who does repair work will be interested in this new rig that allows you to make on-site service calls, and also works great as a backup hoist for shop work.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Lester Rose and his wife, Audrea, live on the road doing volunteer construction work, made possible by their fully equipped workshop.
Read the complete story →From the archive · Full text
Feature story
Featured source:
If you drive a semi-tractor, you probably keep the engine running whenever you drive to a location and are waiting to load or unload a shipment. That keeps the cab warm in winter and avoids difficult restarts of…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Working fields as far as 35 miles from home is less of a hassle than it used to be for Cary Urka, thanks to a couple of service trucks he customized for farm work.
Read the complete story →From the archive · Full text
Reader shop tip
Bob Johnson, Irvington, Ky
“To get rid of my old oil without having to go outside in winter, I put a 55-gallon barrel on a stand outside the building and ran a piece of 3/4-in. heater hose from the barrel into the…
Read the complete tip →From the archive · Full text
Reader shop tip
Charles Carson Sr., Bridgewater, Conn.
“For tubeless tires around the farm that get slow leaks, I just put a bit of used crankcase oil inside to seal them up. Solves the problem.”
Read the complete tip →From the archive · Full text
Reader shop tip
Don Hofer, Wrentham, Canada
“My uncle Dave built a large table-mounted belt sander for his blacksmith shop. It has a swivel so you can sand sideways on the long plate or small plate by tilting the sander straight up with the swivel.…
Read the complete tip →From the archive · Full text
Reader shop tip
Everett W. Gustafson, Brockway, Penn.
“I added a step to my Farmall Cub tractor to make it easier to get on. I used a 2-in. wide piece of strap iron, twisted and bent into the shape of a stirrup. I hooked one end…
Read the complete tip →From the archive · Full text
Reader shop tip
H.L. Baggett, Hollow Road, Tenn.
“I traded for a Snapper SRI30 riding mower with a 12 hp. Briggs & Stratton engine. Unfortunately, it had a lot of problems so I had to do some work on it.
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Illinois Glove Company
Have you ever looked at the pieces of a project and wondered how you were ever going to keep from losing all the screws and other parts? Now, with Silver Back Magnetic Gloves, you won’t have to worry…
Read the complete tip →From the archive · Full text
Reader shop tip
Ken Scharabok, 1645 West Blue Creek Rd., Waverly, Tenn. 37185
“The blacksmithing tools I make for sale on eBay (See Vol. 28, No. 3) require that I keep a small quantity of many sizes of steel on hand. To use space efficiently, I built this rack onto the…
Read the complete tip →From the archive · Full text
Reader shop tip
Lee Dietsch, Hamler, Ohio
Here’s a quick and easy way Lee came up with to fix leaks in pipe such as hydraulic lines on heavy equipment and copper plumbing. Great for farmers and excavators and anyone else running heavy equipment where hydraulic…
Read the complete tip →From the archive · Full text
Reader shop tip
Mark Bruellman, Rolfe, Iowa
“Whenever I use the chop saw in my shop, I don’t like all the dust and smell it makes. To solve the problem, I placed the chop saw on a workbench in front of a d o u…
Read the complete tip →From the archive · Full text
Reader shop tip
Stan McDonald, Foxboro, Ontario
“Re-cently I was asked to cut some small diameter round stock using a lathe. The problem arose when I attempted to cut the thread. The pressure applied by the tool caused the material to bend out of the…
Read the complete tip →From the archive · Full text
Reader shop tip
Steering Wobble On GM Pickups
On 1973 to 1991 GM vehicles equipped with steering column tilt assembly, often the assembly comes loose and wobbles as the vehicle ages. Most people believe the column is worn out but that’s not the case. For some…
Read the complete tip →From the archive · Full text
Reader shop tip
Steve Nienow, Rochester, Minn.
“I use old, worn-out V-belts to hold ropes, hoes and extension cords on hooks. They grip well and are easy to use by looping them around. Works great.”
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Here’s an oldie but goodie that we spotted recently in an auto repair magazine.
Read the complete story →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Dave Nicholas, Martinsville, Ohio
“Whenever I find a big discount store like Walmart with rubbing alcohol on sale for 25 cents a pint or so, I buy a case. Twice a year, around Easter and Thanksgiving, I dump a pint of rubbing…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Dave Nicholas, Martinsville, Ohio
“Once every year I put two teaspoons of brake fluid into the auto transmissions on my vehicles. The brake fluid keeps the front seal and other seals inside the transmission soft so they don’t crack and dry up.…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Gary Anderson, Bowden, Alberta
“After the ‘turtles’ on the cutterbar on our Deere 935 discbine started showing wear, we simply swapped the clockwise turning units with the counter clockwise turning units. This doubled their life expectancy.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Gary Anderson, Bowden, Alberta
“We use several older house dressers with large drawers to store spare parts for our major machines. Each dresser and drawer is labeled clearly as to what’s inside.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Gerald A. Borders, Sullivan, Ind.
“To extend the life of sealed bearings I use a grease needle like the kind used on chainsaw tips. I simply poke a hole in the seal and shoot some grease in. Saves a lot of down time.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Gerald A. Borders, Sullivan, Ind.
“A radiator hose clamp can temporarily replace a locking collar on a bearing.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Gerald A. Borders, Sullivan, Ind.
“I use a non-contact electronic thermometer to check the temperature of bearings, radiators, engines, electrical connections, etc. Saves a lot of problems and time.”
Read the complete tip →From the archive · Full text
Reader shop tip
Jake Penner, Winnipeg, Manitoba
“I found a cheap way to obtain carbide-tipped cutting tools for my metal lathe. I remove carbide tips from junked 10-in. table saw blades and silver solder them onto my lathe tool, then grind them down to fit…
Read the complete tip →From the archive · Full text
Reader shop tip
Jason Godfrey, ph 828 453-8527; email
[email protected]: “On the farm working out of my truck, I sometimes find myself needing a vise for tough jobs. So I came up with this simple vise stand that fits into the receiver hitch on my pickup. The…
Read the complete tip →From the archive · Full text
Reader shop tip
Larry Hershberger, Kalona, Iowa
“I needed a cart for my welding torch so I converted an old gas grill into a torch cart. I re-moved the lid from grill and cut holes the size of my welder’s tanks into the bottom. Then…
Read the complete tip →From the archive · Full text
Reader shop tip
Larry Johnson, Ontario, N.Y.
“I have three 25-year-old pieces of equipment that are all powered by single cylinder Kohler engines that won’t start after they sit idle for a day or two. To solve the problem I put the primer bulbs off…
Read the complete tip →