Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 28, No. 6 (2004)

Vol. 28, No. 6 (2004)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 36–39

37 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Albert L. Url

Albert L. Url, 4117 E. Briges Road, Elk, Wash. 99009 ph 509 292-5119

“I came up with a way to align a shaft without using any tools. I got the idea while installing a Plymouth 318 cu. in. car engine in an International 4-WD truck. The Plymouth engine has a longer tail stock, and the easiest way to make the change was on the universal joint. But when I put the new engine in, there wasn’t room for two drive shafts - one for the transfer case and one for the rear wheels. So I mounted the universal joint between the car engine and the International transfer case, eyeballing it as best as I could. In order to get the drive shaft correctly aligned, I idled the engine so the universal joint was going in a circle and was able to align itself. Then, with the engine running, I welded the transfer case in place (be sure to weld the old frame of the transfer case onto the truck because it saves a lot of alignment work). As the weld cooled, the transfer case centered itself so the two shafts were perfectly aligned with each. The last step was to mount the rear driveshaft.

“The bottom line is that any time you want to align a driver and a driven transmission or any driven unit, if you can operate them before they set where they’ve got to be they’ll align themselves. But you can’t be more than .3000 of an inch off or else the bearings will get out of whack and vibrate, which will quickly wear them out.”

From the archive · Full text
Reader shop tip

Red Rock Mfg.

Red Rock Mfg., 1117 Park Lane, Pella, Iowa 50219 (ph 641 780-1748; www.redrockmfg.com)

Anyone who owns a Ford 2N, 8N, or 9N tractor will be interested in this new combination gas cap and gauge that’s designed to replace the tractor’s original gas cap. These tractors don’t have gas gauges so it’s pretty handy. You simply re-move your existing cap and replace it with the gauge. The unit consists of a float that moves up and down along a spiral twisted piece of metal that turns the pointer on the gauge. This same kind of gauge is used on some riding mowers.

“It lets you see at a glance how much fuel is left in the tank,” says developer Phil Smith.

“It fits neatly under the lid so it won’t dis-tract from the appearance of your tractor.”

Sells for $23 including S&H. The company offers other products for N-Series tractors including Dowden foot throttles, parking brakes, Sherman transmission lever, auxilliary pto lever, and Greene Drawbar lock. A free catalog is available.

From the archive · Full text
Reader shop tip 1 of 2

Douglas J. Hart

Individual tip 1 of 2 from this reader’s published contribution.
Douglas J. Hart, Bethel, Vt.

“My 1996 Lumbermate Bandmill was originally powered by a 20 hp Honda engine which ran too slow and was underpowered. I solved the problem by replacing the Honda with a Suzuki 3-cyl. fuel-injected, overhead cam, water-cooled gas engine. I did the job myself and got the power and speed that I needed.

From the archive · Full text
Reader shop tip 2 of 2

Douglas J. Hart

Individual tip 2 of 2 from this reader’s published contribution.
Douglas J. Hart, Bethel, Vt.

“To put up a low-cost building to work on my equipment during below zero weather, I sawed out some 2 by 4’s to frame up a gam-brel roof-style shop and then covered the frame with inexpensive blue tarps. I used spring clamps to hold the ‘plastic’ doors together. A wood stove and small kerosene heater, along with the sun, kept me warm enough to work out of the wind. It was a cheap but effective solution.”

From the archive · Full text
Reader shop tip 1 of 3

Hebert Wodtke

Individual tip 1 of 3 from this reader’s published contribution.
Hebert Wodtke, Loogootee, Ill.

“I replace farm wagon tires with used 16-in. pickup tires. I like tires with 8-ply or more. Rather than buy tubes, I use a liberal amount of talc seed lubricant in each tire and on each bias tube. I always inflate to the recommended pressure, and I mount my own tires.

From the archive · Full text
Reader shop tip 2 of 3

Hebert Wodtke

Individual tip 2 of 3 from this reader’s published contribution.
Hebert Wodtke, Loogootee, Ill.

I install a grease zerk in the dust cap on each wagon wheel. It makes lubing wheels a much quicker job. In more than 40 years of farming, I’ve accumulated more than 23 grain wagons. Most of them are 165 bu. or smaller.

From the archive · Full text
Reader shop tip 3 of 3

Hebert Wodtke

Individual tip 3 of 3 from this reader’s published contribution.
Hebert Wodtke, Loogootee, Ill.

“I believe in preventative maintenance, so whenever a motor vehicle reaches 16 years of age I start checking prices for a replacement radiator even if there’s nothing wrong with the one I already have. In my opinion, a total replacement is less expensive than repairing the original radiator. I don’t want problems on the road, and the cost for a tow bill will go a long way toward the cost of a new replacement radiator. If you replace a radiator before it develops problems, you can do it when you have time - not on the road in a panic.”

From the archive · Full text
Reader shop tip

Posi Lock Puller, Inc.

Posi Lock Puller, Inc., 805 Sunflower Ave., P.O. Box 246, Cooperstown, N. Dak. 58425 ph 800 533-5761 or 701 797-2600; www.posilock.com

This company recently introduced new Hold-Et magnetic vise clips that eliminate the need for an extra pair of hands when working with a vise. They also let you close the vise as tight as you want without damaging the threads.

Hold-Ets consist of a pair of 3-in. lengths of angle iron that magnetically hold sockets in a vise for assembling and disassembling universal joints and other jobs. They’re made from rigid aluminum so they won’t damage any threads. Hold a number of shapes and sizes of objects including screws, rings, c-clips and springs, etc. You can use them as a jaw liner for non-marking material. The unit can hold 5 1/2 lbs. vertically and 2 3/4 lbs. horizontally.

Hold-Ets sell for $14.99 plus S&H.

From the archive · Full text
Reader shop tip

Wingfield Distributors, Inc.

Wingfield Distributors, Inc., 4712 N. Cunningham Ave., Urbana, Ill. 61801 ph 800 637-6712; fax 217 643-7849; www.wingfields.com

This company offers a new screw-holding driver made in Germany. The design permits single-handed operation for starting a screw, allowing easier access in tight places. It allows you to place screws through holes or in hard-to-reach places without the screw falling off.

The driver is equipped with a quick release thumb switch that allows fast, easy screw release. You place the screw inside a spring-loaded holder. Once the screw is started, you pull back on the driver shaft and pull the driver down and away, then go back and finish the operation. Two different driver models are available to handle Phillips or slotted-type screws. Call for size application.

Sells for $24 plus S&H.

From the archive · Full text
Reader shop tip 1 of 2

Mark Burrow

Individual tip 1 of 2 from this reader’s published contribution.
Mark Burrow, 11221 N. 100 th St., Altamont, Ill. 62411 ph 618 483-5598

Mark mounted a homemade reel on top of his air compressor, providing fast payout of the pressure hose and equally fast winding back up. He used a pair of old discs to make the reel, fashioning them into a spool which he bolted onto the tank.

“The reel is ready for use whenever and wherever I need air pressure in my shop,” says Mark.

From the archive · Full text
Reader shop tip 2 of 2

Mark Burrow

Individual tip 2 of 2 from this reader’s published contribution.
Mark Burrow, 11221 N. 100 th St., Altamont, Ill. 62411 ph 618 483-5598

He also came up with a unique way to transport gas welding tanks that makes use of an ordinary hand truck. He constructed a metal stand for the welding tank, leaving a bit of extra space below the base. It allows him to slip the hand truck under the base. Now he can move the tank and welding torch anywhere, even if it’s in a close place, and then remove the transport wheels by simply removing the hand truck.

From the archive · Full text
Reader shop tip

George Wissinger

George Wissinger, Huntington, Ind.

He fixed a common problem on his 1963 New Holland 268 small square baler.

“It’s not unusual in that line of balers for the belt to slip on the pickup when you’re in heavy hay or long stubble,” he explains.

“I found a simple modification that I was able to make in an hour and a half after I got the parts.”

He removed the belt drive (V-belt and the V-belt pulley) from the pickup and replaced it with sprockets and no. 2040 roller chain. He installed the two sprockets he bought at a parts store with two “Weld-a-Hubs.”

“I welded a 1 by 2-in. piece of scrap iron to the hub, and drilled a hole through this tab, and also the sprocket. Then I put in a 1 by 2 by 1/4-in. thick shear bolt for protection. If something happens to the pickup, it will shear the bolt. In the 20 years since I made the modification, I’ve only sheared two bolts. It’s a totally different performing machine.”

Wissinger says the job was quick because he only had to weld one sprocket. The other sprocket is driven by the tab with the 1/4-in. bolt in it. The more positive drive to the pickup gives the baler more capacity.

“I’ve done three of these balers – mine and two others in the neighborhood. People were so impressed with mine that they wanted it on theirs, too,” he says.

From the archive · Full text
Reader shop tip

Robert Ellis

Robert Ellis, High Hill, Mo.

“I designed this tool to loosen the belt that drives the pickup on older model Vermeer balers to make it easier to grease the bars at each end of the pickup. It saves a lot of skinned knuckles,” says Robert Ellis, High Hill, Mo.

The baler’s pickup is equipped with five or six bars, with grease fittings at both ends. To grease the bars, the operator has to either loosen the belt or remove it so he can rotate the pickup. The tool that Ellis fabricated simply takes the tension off an idler on the belt, allowing the operator to slip the belt off the pulley. The idler is attached by a short metal bracket to a shaft.

Ellis welded a 6-in. length of rectangular tubing and a short stub pipe together, with a metal tab on one side. The device slips onto a 2-ft. steel pipe handle. When the tool slips over the shaft, the tab extends over the idler bracket. The operator pushes down on the pipe handle to lower the idler and release tension on the belt.

“My brother Kermit uses it on his baler. He had been using a crescent wrench to rotate the shaft, but it didn’t work very well and he often skinned his knuckles,” says Ellis.

From the archive · Full text
Reader shop tip

Roger Kuntz

Roger Kuntz, K-Tech, 5251 Co. Rd. X, Grainfield, Kansas 67737 ph 785 673- 5560

You can keep your wire welding gun close at hand with this new “magnetic base” welding gun holder.

It stands 17 in. tall and has a 5-in. dia. magnetic base at the bottom, and a pair of “V” shaped, foam-cov-ered metal prongs at the top.

“The magnet has 60 lbs. of pulling power, so it provides a firm grip on any metal surface and won’t tip over. Yet you can easily move it to wherever you need it,” says inventor Roger Kuntz.

“The foam grips are gentle on the wire gun and insulate it from arcing.”

Wire welding guns are becoming more popular all the time, says Kuntz, but there’s one big problem.

“When you lay the gun down, the trigger can accidentally discharge and cause an unplanned wire feed with the gun sending out electrode sparks. It can be dangerous and annoying. It takes time and effort to lay the gun down just right so that it doesn’t go off.

“To solve the problem, some people weld small metal prongs onto the sides of their welding table. But that won’t help if you have to use the gun somewhere else and the holder is out of reach.”

Sells for $21.95 plus $5 S&H.

From the archive · Full text
Reader shop tip 1 of 3

Jim Matthews

Individual tip 1 of 3 from this reader’s published contribution.
Jim Matthews, Saskatoon, Sask.

“To come up with a cheap tarp, I go to our local lumber yard and pick up pieces of plastic that are used to wrap lumber when it’s shipped. Normally, most lumber yards just throw this plastic away. I’ve found a variety of uses for these tarps. For example, I place them behind the doors inside grain bins in order to keep grain from leaking out. It works better than trying to seal the outside because the grain pushes the tarp against the door, sealing any cracks and holes. It’s amazing how well this stops grain from leaking. It also saves a lot of duct tape.

From the archive · Full text
Reader shop tip 2 of 3

Jim Matthews

Individual tip 2 of 3 from this reader’s published contribution.
Jim Matthews, Saskatoon, Sask.

“If you have a leak in a fuel tank or an engine cooling system, you can use a vacuum cleaner on the tank opening to create a good vacuum. (You might want to drain some coolant if it’s very full). Once a good seal is formed, you can take the hose off or the drain tap and reseal it. Or, you can replace the hose while the vacuum is on the tank without having to drain the system. You can use this idea to change fuel filters or hydraulic fittings without spilling a drop.

From the archive · Full text
Reader shop tip 3 of 3

Jim Matthews

Individual tip 3 of 3 from this reader’s published contribution.
Jim Matthews, Saskatoon, Sask.

“If you have a small shed without any electricity and want to have light inside it, you can use a solar battery charger to power a light. You can buy these solar battery chargers cheap at Wal-Mart and other stores. Just hook the charger up to a car battery. For lights you can use marker lights or other spare lights you already have around the farm or buy them cheap at surplus stores. If you want to get fancy you can hook up to an on-off wall switch.”

From the archive · Full text
Reader shop tip

Rich Vink

Rich Vink, Topeka, Kansas

“To provide better light inside my machine shed, I’ve mounted theater stage lights on the building’s trusses and aim the light beams down toward my farm equipment. It saves the hassle of using a drop light and also results in better lighting.”

From the archive · Full text
Reader shop tip

Steve Nelson

Steve Nelson, Winston-Salem, N.C.

“I had a problem with the 2-WD shift lever on my Kawasaki Mule. The lever wouldn’t re-lease until it really torqued up and made a big bang. The problem is the spring that re-turns the selector lever at the transmission is too weak in its original location. I decided to release the tension and index the base of the spring to the next ridge on the housing. Then I retensioned the lever and connected the spring to the lever. Problem solved.”

From the archive · Full text
Reader shop tip

Bradley Moore

Bradley Moore, Krypton, Ky.

“A reed valve on my small Sears compressor broke and no replacement was available. I made one from a feeler gauge leaf but it didn’t last very long. Then two years ago I made another one from a plastic Pennzoil oil container, and it’s still working.”

From the archive · Full text
Reader shop tip 1 of 3

Chuck Golankiewicz

Individual tip 1 of 3 from this reader’s published contribution.
Chuck Golankiewicz, Pittsburgh, Penn.

“When Troy Bilt told me they couldn’t supply parts for my 33-in. mower, I had a local machine shop make parts and they work even better than the original ones.

From the archive · Full text
Reader shop tip 2 of 3

Chuck Golankiewicz

Individual tip 2 of 3 from this reader’s published contribution.
Chuck Golankiewicz, Pittsburgh, Penn.

“The driveshafts on my Deere tracked snowblower rusted and froze up. After cleaning, I drilled and installed grease fittings to prevent further rusting.

From the archive · Full text
Reader shop tip 3 of 3

Chuck Golankiewicz

Individual tip 3 of 3 from this reader’s published contribution.
Chuck Golankiewicz, Pittsburgh, Penn.

“Keep a supply of parts and belts as replacements. Stick to one brand to make it easier. I prefer Briggs & Stratton.”

From the archive · Full text
Reader shop tip 1 of 2

Timothy Locke

Individual tip 1 of 2 from this reader’s published contribution.
Timothy Locke, Bremen, Ala.

“I had trouble leaving small walk-through gates open, so I attached screen door springs to them so they would close automatically.

From the archive · Full text
Reader shop tip 2 of 2

Timothy Locke

Individual tip 2 of 2 from this reader’s published contribution.
Timothy Locke, Bremen, Ala.

“I have a small Yanmar tractor that’s light on front, so I melted old wheel weights into an iron skillet to make front weights that hold the front end down.”

From the archive · Full text
Reader shop tip

Chris Kornkven

Chris Kornkven, N6280 County P, Helenville, Wis. 53137 ph 920 699-2376)

“To help keep my shop clean, I needed some way to store metal stock or other lengths of odds and ends. I had some extra lengths of wire stock panels on hand. I cut down the panels and hung three of them from the rafters in my shop, which are spaced 10 ft. apart. I hung one panel from one rafter, and two panels from another rafter. Since the panels flex a little, I was able to spread apart the bottom ends of the two panels that hang from the one rafter. This setup lets me store long stock as well as shorter stock by putting the short stuff on the two panels that are close together.”

From the archive · Full text
Reader shop tip

Hy-Capacity Eng. & Mfg., Inc.

Hy-Capacity Eng. & Mfg., Inc., Hwy. 169 S., Humboldt, Iowa 50548 (ph 800 247-1824 or 515 332-2125; www.hy-capacity.com)

Anyone who owns an Oliver/White 1650 or 1750 tractor will be interested in this company’s new clutch conversion kit. The tractor’s original clutch comes with a 3-lever Borg-Beck pressure plate with an I-bolt that tends to break prematurely. When that happens, you have to buy a new clutch.

The new clutch conversion kit uses a diaphragm pressure plate with a disc and bearing. It has the same spring pressure holding power but doesn’t have any I-bolts to break. Kits are available with pressure plates and include anything from woven to padded type discs. A pressure plate with four pads per disc retails for $236.

Shop feature stories

From the archive · Full text
Feature story

Barrel Stopped Radiator Clogging

Featured source:

When bush hogging tall, thick weeds, Paul Lowrance had trouble with the weed seeds shattering and getting sucked through the front grill of his tractor, clogging up the radiator.

“I had to clean out the grill constantly,” says the Soper, Okla., farmer, who went looking for an inexpensive solution to the problem.

“I cut a plastic barrel in half and drilled some holes along the edge, then wired it to the front grill guard. It protects the grill opening from flying debris and pushes everything to one side or the other,” says Lowrance.

“Air is still able to come in from the back side of the barrel. I also folded a double layer of window screen in between the grill and the radiator to catch whatever material gets sucked up.”

Contact: FARM SHOW Followup, Paul Lowrance, P.O. Box 64, Soper, Okla. 74759 (ph 580 345-2713; email: [email protected]).

From the archive · Full text
Feature story

Mini-Jack Gets Into Tight Spots

Featured source:

A tiny new hydraulic jack can get into tight spots, yet it has an amazing lift capacity of five tons.

The Sidewinder 9105A mini-jack has a retracted height of just 2 9/16 in. It operates either horizontally or vertically and can be used as either a jack or a spreader. Works great wherever there’s not enough room to swing a hammer for driving out pins, and to take out dents, etc. It can also be used with a manual gear puller to apply force onto the jaws that hold the gear.

Sells for $99.99 plus S&H. Contact: FARM SHOW Followup, Tool Warehouse, Inc., 3410 East 42nd St., Minneapolis, Minn. 55406 (ph 800 753-4086 or 612 722-4260; website: www.tool warehouseinc.com).

From the archive · Full text
Feature story

He Used Dynamite To “Pull” Car Engine

Featured source:

When David Curtis took an early 1980’s Cadillac to a junk yard to scrap it, they wouldn’t take it because he didn’t have the title.

“They told me that without the title, they couldn’t lawfully take the car unless the engine was removed from it,” says David.

“The law is designed to make it more difficult for thieves to sell stolen cars at scrap yards.”

His son tried using a torch to cut the engine out of the car, even turning it upside down with a front-end loader to make it easier to get at the engine mounts. However, something caught on fire and before long the entire car was on fire.

“It was a big smoking mess,” says David.

They smothered the fire by dumping dirt onto the car.

They used 10 sticks of dynamite in the engine area with the car upside down, putting five sticks on each side of the frame rails. The sticks of dynamite were connected together with Primacord so they would go off at the same time. The scrap yard wouldn’t take the car with an enclosed gas tank on it so they used dynamite to get rid of the tank, too.

To reduce the noise and force of the blast, they used the loader to dump a pile of clay on top of the car again. Then they lit the fuse. The blast cut the car in half, separating the front part from the rear, and sent the engine flying.

“The funniest part was that a column of fire and smoke 60 to 80 ft. in diameter immediately shot about 200 ft. up into the air. It even had a mushroom cloud on top of it,” says David.

After the explosion, they loaded the two halves of the car onto a trailer and hauled it to the scrap yard.

David, who is a licensed dynamite blaster, says he doesn’t recommend this idea to anyone who isn’t licensed to blast dyna-mite.

“I use dynamite to make irrigation ditches deeper, to remove big rocks from dirt roads, on beaver dams, and so on,” he notes.

Contact: FARM SHOW Followup, David K. Curtis, 1613 North Perry Park Rd., Sedalia, Colo. 80135 (ph 303 688-4285).

From the archive · Full text
Feature story

Air Hitch Smoothes Ride For Truck And Trailer

Featured source:

Since they retired, Lester Rose and his wife, Andrea, have lived on the road for the past 13 years with no permanent address (see re-lated story on page 39). In that time they learned that the hitch pulling their travel trailer is pretty important.

The Roses travel in a 1 1/2-ton cargo van equipped as a travelling shop. Because the truck is so stiff, it destroyed the hitch on a travel trailer over a period of four years.

So, Lester invented a hitch that he says has worked perfectly for nine years. Although there are now similar hitches on the market, he thinks his hitch is “light years ahead” of anything out there.

“The hitch plate rides on a pair of air-loaded shock absorbers,” he explains.

“Not only does this keep the trailer from getting beat to pieces, but it also smoothes out the ride in the truck. Since last winter, we’ve been pulling a 30-ft. travel trailer behind this truck that weighs in at close to 17,000 lbs. and it has worked great.

”To carry the tongue weight of the trailer, Rose runs about 180 psi to the shocks from a compressor he carries with him.

“I’ve never built anything that has worked so well over such a long period,” he says.

Contact: FARM SHOW Followup, Lester Rose, 2180 Pear St. S.E., Deming, New Mexico 88030 (email: [email protected]).

From the archive · Full text
Feature story

Trailer Doubles As A Service Lift

Featured source:

Anyone who does repair work will be interested in this new rig that allows you to make on-site service calls, and also works great as a backup hoist for shop work.

This Lift-A-Way trailer has a built-in hoist, allowing it to double as a service lift that can lift vehicles from 4 to 6 ft. high. It can handle vehicles weighing up to 8,000 lbs.

The trailer measures 25 ft. long and has a frame made from 6-in. channel iron, with the space between the frame rails left open leaving room to make repairs to the underside of the raised vehicle. The vehicle is raised by four adjustable lift legs - two on front and two on back. A pair of 3-in. dia. dual action hydraulic cylinders, equipped with safety interlock valves, do the lifting and are operated by a built-in, self-contained 110-volt hydraulic power pack.

Dual side hydraulic levers - one on each side - are used to raise the trailer. Side walk-way rails provide access to either side of the engine.

The trailer is loaded via a flip-up pair of loading ramps on back. To raise the vehicloe, you pull a pin from each of the four legs, then hydraulically raise the unit and reinsert the pins.

Sells for $9,300. Contact: FARM SHOW Followup, Oldenkamp Inc., P.O. Box 630, Hull, Iowa 51239 (ph 712 439-1240; email: [email protected]; website: www.liftaway.com).

From the archive · Full text
Feature story

“Lift Boom” For Riding Mower

Featured source:

By modifying an old No. 5 hitch off an IH planter, Leonard Seltzer built a “lift boom” that makes it easy to do maintenance work on his riding mower. A 1-ton chain hoist does the lifting.

The 10-ft. long, Cat. I bridge hitch was designed to pull a field cultivator going ahead of a planter.

He started by removing the rear dolly wheel and welding a steel plate over the open end. Next, he heated the hitch plate and bent it down to conform with the shape of the boom. Then a hole was cut at the bend and a slot made to accommodate a medium duty chain, which serves as the top link hook-up. At the bottom of the boom, he removed the original clamps. Then he took the boom to a local machine shop where the holes were bored out to 1 1/8 in. for Cat. II size pins that attach to the tractor’s lower lift arms. On the top end, a 3/4-in. hole was bored and a 3/4in. I-bolt put in place to support the chain hoist.

The factory Cat. II pins were an inch short due to the thickness of the 2 by 3-in. tubing that makes up the main frame of the boom, so he made new ones on a lathe to fit the 3-pt.’s lower lift arms. To complete the hook-up, he removes the 3-pt. top link and places a chain around the original pin that held the top link.

“I use it to service my Woods model 6170 zero turn riding mower, and it works great,” says Seltzer.

“I put a light chain around the mower’s dolly wheels and arms, then hook the chain hoist to the chain. It’s a heavy mower but the boom has no problem lifting it. I think it could be used to lift any garden tractor with up to 20 hp.”

Contact: FARM SHOW Followup, Leonard Seltzer, 16040 W. Elmwood, Manhattan, Ill. 60442 (ph 815 478-3578).

From the archive · Full text
Feature story

Mower Hoist Makes Service Easy

Featured source:

“It provides me with a safe and easy way to clean the deck and sharpen the blades on my riding mower,” says Arnold Hussong, Okabena, Minn., who recently sent FARM SHOW photos of an electric-operated hoist his son made for him. It allows him to raise his Snapper riding mower.

The hoist was built from 3-in. sq. tubing and measures 12 ft. high and wide, with the legs spread 4 ft. apart. A winch on top is powered by a 1/2 hp electric motor. Hussong attached a short length of chain to the front part of the mower, which he hooks up to the winch cable “I’m getting on in age and don’t have the strength I used to have, so this really helps,” says Hussong.

Contact: FARM SHOW Followup, Arnold Hussong, 306 N. Grove St., Okabena, Minn. 56161 (ph and fax 507 853-4591).

From the archive · Full text
Feature story

Service Trucks Make Fieldwork Easier

Featured source:

Working fields as far as 35 miles from home is less of a hassle than it used to be for Cary Urka, thanks to a couple of service trucks he customized for farm work.

His knuckle boom straight truck is handy for transporting and repairing field equipment, while his home-built service truck gives him a shop on wheels.

“The knuckle boom truck eliminates the need to find a place to load and unload trailers,” says Urka.

“It will easily handle about 2 1/2 tons, so I can pick up pallets, cultivators, fertilizer tanks and even small tractors. The boom is out of the way, so I have full use of the bed.”

Urka bought the snub-nosed 1984 Mack truck cheap, complete with the boom on back. It was operable, but not well maintained. He fixed it up with new brake lines, a valve job and a new cab, put a new axle under the front end and got it back in shape. He also put a heavy-duty under-ride bumper on the back to prevent a car from sliding under if it hit him from the rear. He added a full set of slings and straps to use instead of tie downs, and put a toolbox on either side. When finished, he had a state inspector check it out and got a clean bill of health.

“It’s extremely easy to drive, which is important with workers who are not trained truck drivers,” says Urka.

“I’ve hauled logs with it and even hauled a couple of pieces of a train engine. When I need to sharpen my Bushhog blade, I just lift it up on edge and grind down the blade. It’s the ultimate utility truck.”

Urka’s other service truck may be the ultimate shop on wheels. The ‘74 Chevy truck was in good shape when he bought it, needing only a brake job. Though it had toolboxes on it, Urka stripped it down and rebuilt it to hold a 20 hp air compressor engine, welding generator and bottle racks, and even its own chop saw. Everything is enclosed with doors and drawers for easy access. It even has a couple of outlets for electrical hook ups.

“Everything is out of the weather and out of eyesight,” he says.

“The tailgate folds down with a couple of vises on it for field repairs.”

The old bed had wheel wells sticking up into it, so he narrowed the new box down and covered it above the wheel wells. The new higher floor created storage space between the wheels for steel supplies. In the drawers is a full selection of nuts and bolts and pipefittings. When he changed steel cultivator shovels recently, he had the 50 nuts he needed right there.

Urka estimates that he has put about $6,000 into the truck after buying it for $3,500. He says the heavy truck beats worrying about constantly overloading.

“I wanted something to carry tools, stock and other supplies so I didn’t have to go hunting,” he explains.

“It weighs about 17,000 to 18,000 lbs. fully loaded.”

Contact: FARM SHOW Followup, Cary Urka, 16919 Pole Rd., Bretheren Mich. 49619 (ph 231 477-5364; email: [email protected]).

From the archive · Full text
Feature story

Mobile Workshop Travels The Country

Featured source:

Lester Rose and his wife, Audrea, live on the road doing volunteer construction work, made possible by their fully equipped workshop.

The Roses have put on over 100,000 miles in the last 13 years, driving their 1987 1 1/2-ton cargo van that Lester outfitted for on-site wood and metal work. The unit has a 175 hp, 6-cyl. diesel engine and a 14 by 8 by 7-ft. box on it that’s jam-packed with tools and features.

The 17,000-lb. rig also pulls a 30-ft. travel trailer that has been the Roses’ only home for 13 years.

The interior of the truck box is lined with workbenches made from 3/4-in. square tubing, with drawers below and cabinets above, all full of hand tools. There’s a steel bench with a bench grinder, a mechanical vice, an acetylene torch, planer, a 6 by 48-in. belt sander, a 12-in. band saw, an 18-in. metal turning lathe, a drill press, and a wood turning lathe that requires setting up. And that’s just one side!

On the other side, there’s a 10-in. radial arm saw, a chain saw, an air compressor, and sticking up through the table, there is a router.

The workshop has a 5,000-watt generator built into the side of the truck box. Five 4-ft. fluorescent lights provide excellent lighting.

“Everything can run off either the generator or regular AC power, if we can plug in,” Rose says.

“I made steel steps that slide under the truck bed when travelling, and they can also fold down into a ramp. There’s a little adjusting rod on each side of them so they’re always level.”

Rose says his rig is extremely compact, but it works great.

“I can cut down the middle of a 4 by 8-ft. sheet of plywood and walk past it. It’s hard to believe but there’s enough room,” he says.

“It took me a month to build this rig. We’ve been volunteering at state parks, national wildlife refuges, and national historical parks, where I work at construction of buildings, bridges and other miscellaneous smaller jobs. At one location, I built an entire RV park.”

Both Lester and his wife are on Social Security. State parks and wildlife refuges often provide them with free RV sites to park in, and some will pay stipends ($7 to $15 per day) for Lester’s work.

“We don’t have too much expense,” he explains.

Contact: FARM SHOW Followup, Lester Rose, 2180 Pear St. S.E., Deming, New Mexico 88030 (email: lester_rose @hotmail.com).

From the archive · Full text
Feature story

Pump Eliminates Need To Idle Semi-Tractor Engines

Featured source:

If you drive a semi-tractor, you probably keep the engine running whenever you drive to a location and are waiting to load or unload a shipment. That keeps the cab warm in winter and avoids difficult restarts of a hot engine.

Over-the-road trucker Robert Jordan of Juneau, Wis., says his new Orbit engine heat transfer system provides two to four hours of free heat after the engine has been shut down, or can be used to cool off a hot engine in summer.

The system uses a 12-volt pump to circulate hot engine coolant into both the cab and bunk heater cores, just as if the engine and water pump were still running. Two thermostats are used, one in the cab and one in the bunk, to control interior blower fan use. The system shuts down automatically once engine coolant temperature falls to 80 degrees.

“It provides up to four hours of heat depending on the temperature outside,” says Jordan.

“It takes advantage of the fact that a semi tractor’s engine typically weighs more than three tons, so there’s a lot of heat available in it. I use it on my own truck and never idle the engine at all. The only time the engine runs is when the wheels are turning.

“The average truck on the road today spends as much time idling as it does driving. It uses 1 1/2 gal. of fuel for every hour the engine is idling. In a year, that amounts to about 2,000 gallons.

“Another benefit is that you aren’t using any fossil fuels to keep the cab or bunk comfortable. I believe the time is coming when truckers will be allowed to run their engine only when their truck is moving.”

The magnetically-driven pump installs in line with the engine cooling system. As you drive down the road the pump is free wheeling.

“The only time the pump motor and pump drive are magnetically connected is when the pump is electrified,” says Jordan.

The system has the added benefit of engine cool down during hot months, he says.

“I have a summer switch connected to a 150-degree engine temperature switch that will shut off the pump automatically once the engine block cools to 150 degrees,” he notes.

The basic system, which includes the pump, toggle switch, fuse, and instructions, sells for $300 plus S&H. Also available are optional 80 and 160-degree temperature switches which sell for $60 apiece.

Contact: FARM SHOW Followup, Robert Jordan, N5112 Hwy. A, Juneau, Wis. 53039 (ph 920 386-2957; email: robert@idle free.net; website www.idlefree.net).