Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW

Tools

5957 shop tips and stories · page 81 of 100, newest issues first.

From the archive · Full text
Reader shop tip

Rich Bednarski

Rich Bednarski, 215 South Buffalo Rd., Washington, Pa. 15301 (ph 800 832-6350 or 724 345-3546)

“I can supply all the parts necessary to rebuild mechanical-style torque amplifiers found on old International Harvester tractors made in the 1950’s and early 1960’s, and I can also rebuild them. My torque amplifier parts are less expensive…

Read the complete tip →
From the archive · Full text
Reader shop tip

Dale Simon

Dale Simon, 1993 E. 1650 th St., Coatsburg, Ill. 62325 (ph 217 936-2459; Website: [email protected])

“I used parts from old photocopy machines, including the electric motor, rollers, bearings, chains and sprockets, to make a tumbling parts cleaner. It’s not very high tech but it works great. It uses two rollers, spaced 5 in.…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Profi Magazine

Individual tip 2 of 2 from this reader’s published contribution.
Profi Magazine, www.profi.com

When you have to clamp a bolt in a vise, most people try using wood or some other soft material to avoid damaging threads. But that often does not provide enough gripping power. Another alternative is to cut…

Read the complete tip →
From the archive · Full text
Reader shop tip

Roger Kuntz

Roger Kuntz, K-Tech, 5251 County Road X, Grainfield, Kan. 67737 (ph 785- 673-5560)

If you’ve got a blade plow, chances are at one time or another you’re going to need a replacement turnbuckle, says Roger, who makes an extra heavy-duty replacement for Flex-King, Richardson, and Noble blade plows.

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Pete Peters

Individual tip 1 of 2 from this reader’s published contribution.
Pete Peters, Osler, Sask.

“I made a nifty funnel stand that avoids the mess of storing oil funnels on your workbench. It consists of concave discs mounted - curved sides down – on an upright piece of pipe. Then you drill a…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Pete Peters

Individual tip 2 of 2 from this reader’s published contribution.
Pete Peters, Osler, Sask.

“Here’s a jack attachment that I use for removing transmissions. It fits onto a standard floor jack. It consists of a flat metal rack made from short pieces of strap iron. A metal shaft fits down into the…

Read the complete tip →
From the archive · Full text
Reader shop tip

Roy Crane

Roy Crane, Martinsvile, Ill.

“On an International Harvester 1460 combine, the pan under the beater was hard to raise or lower because it doesn’t have any way to get ahold of it. I replaced the short bolts on the rear of the…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Tom Williams Machine

Individual tip 1 of 2 from this reader’s published contribution.
Tom Williams Machine, Inc., HCR 1, Box 1-A, Aurora, Mo. 65605 (ph 417 678- 3723; fax 417 678-6000)

“We made our 5-gal. wet and dry vacuum easier to carry by bolting a pair of small brackets to the sides of the vac and attaching a 5-gal. pail handle to them. Without a handle, the vac is…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Tom Williams Machine

Individual tip 2 of 2 from this reader’s published contribution.
Tom Williams Machine, Inc., HCR 1, Box 1-A, Aurora, Mo. 65605 (ph 417 678- 3723; fax 417 678-6000)

“I also mounted a pail handle on top of a 3-gal. pump-up spray tank and mounted a 1-in. dia. PVC pipe alongside the tank for storing the sprayer wand. I ran a No. 8 wire band around the…

Read the complete tip →
From the archive · Full text
Reader shop tip

Frankie Purser

Frankie Purser, 680 Purser Rd., Vanceboro, N.C. 28586 (ph 252 244-0750)

“I installed a kit from Ford New Holland on my TW 15 tractor that lets me disconnect the remote hydraulic outlets without having to get off the tractor and use levers. The kit consists of a small Teflon…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 4

Glen Teel

Individual tip 1 of 4 from this reader’s published contribution.
Glen Teel, Hays, Kansas

“The clutch slave cylinder on my 1988 Chevrolet S-10 pickup started leaking and the company wanted more than $90 for repair parts. I didn’t want to spend that much so I bought a 50 cent O-ring and mounted…

Read the complete tip →