Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW

Tools

5957 shop tips and stories · page 12 of 100, newest issues first.

From the archive · Full text
Reader shop tip 1 of 2

Lee Roy Pipkin

Individual tip 1 of 2 from this reader’s published contribution.
Lee Roy Pipkin, Gilroy, Calif.

“I clean grease and dirt from my hands with Goop grease remover that you can buy at Walmart or Amazon. I used to clean tools separately but now I combine the two, cleaning both my tools and hands…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Ready Davis

Individual tip 1 of 2 from this reader’s published contribution.
Ready Davis, Bigfoot Equipment & Repair, Willow Creek, Calif.

“As a small town Husqvarna dealer, I like to check your Best & Worst Buys to see how my brand is doing. I recently saw reports by a couple readers who I might be able to help.

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Ready Davis

Individual tip 2 of 2 from this reader’s published contribution.
Ready Davis, Bigfoot Equipment & Repair, Willow Creek, Calif.

“Another reader, Larry Johnson in Ontario, N.Y., is unhappy with his Husqvarna TS354D tractor’s deck mounting. He said he was having issues with the rear bar once the front was disconnected and didn’t like taking the belt off…

Read the complete tip →
From the archive · Full text
Reader shop tip

L.D. Shumaker

L.D. Shumaker, Richfield, Ohio

“I wish there was a company out there that sells new or rebuilt rear drives for zero-turn mowers. They’re usually the first thing to go on these machines, especially the left drive since we trim counter clockwise. Or…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Larry Frederickson

Individual tip 1 of 2 from this reader’s published contribution.
Larry Frederickson, Monmouth, Ill.

“Years ago I stopped using liquid soap to mount tires on steel rims because it causes rusting along the rim edges and takes some of the softness out of the tire bead so that it tears when dismounting…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Thomas Dart

Individual tip 1 of 2 from this reader’s published contribution.
Thomas Dart, Northport, Ala.

“To hook up heavy 3-pt. implements to a tractor, I use an engine hoist to do the lifting. It works well because it’ll slide in under the hitch.

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Aaron M. Miller

Individual tip 2 of 2 from this reader’s published contribution.
Aaron M. Miller, Orwell, Ohio

“To keep grass from sticking under a mower deck, first clean the deck as well as you can. Then coat liberally with Fluid Film undercoating. Then heat with a propane torch so the film soaks into the rusted…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 3

Ben Parks

Individual tip 1 of 3 from this reader’s published contribution.
Ben Parks, Austin, Texas

“When I did a mechanical restoration of my 1970 Jeep, the first thing I did was to replace the distributor points with a Pertronix ignition kit (www.pertronixbrands.com; ph 909-599-5955). I also installed a Pertronix ignitor coil. With the…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 3

Ben Parks

Individual tip 2 of 3 from this reader’s published contribution.
Ben Parks, Austin, Texas

“I did have a problem with the jeep overheating when sitting still in traffic in hot weather. After upgrading the radiator, I looked around for a better cooling fan to replace the original 4-blade fan and found a…

Read the complete tip →
From the archive · Full text
Reader shop tip 3 of 3

Ben Parks

Individual tip 3 of 3 from this reader’s published contribution.
Ben Parks, Austin, Texas

“When the Jeep’s speedometer quit working, I sent it to Bob’s Speedometer to repair. They customized it with a voltmeter, repaired the fuel gauge, and recolored the face. Their service is expensive but worth the money and it…

Read the complete tip →