Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Bob Payne, Coldwater, Miss.
“When working under or inside a machine, visibility can be a problem - even in a well-lit shop. I’ve tried different kinds of strap-on lights and really like the Streamlight 66318 light, which clips onto the bill of…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Bob Payne, Coldwater, Miss.
“To store long-handled tools, I cut the top off a plastic 55-gal. barrel and fill it with pieces of 4-in. dia. thin wall pvc pipe. The pipe holds the tools separate from each other. For D-handle tools, I…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Brandon Parks, Geno’s Garage, Cumming, Ga. (www.genosgarage.com; ph 800-755-1715)
“The oil filter in 2013-2018 Ram Cummins heavy-duty pickups is notoriously difficult and messy to remove. Our oil filter cap-off tool threads onto the top of the filter, allowing you to easily pull the filter straight out without…
Read the complete tip →From the archive · Full text
Reader shop tip
Glenn Wilson, Crittenden, Ky.
“I store log chains in 5-gal. buckets with the hooks hanging on the edge of the bucket. Makes it easy to grab and go and you don’t have to search for the ends.”
Read the complete tip →From the archive · Full text
Reader shop tip
H.D. Weaver, Baird, Texas
“I read where a reader had trouble with the control cable freezing in cold weather on his front end loader controls. I had the same problem on my New Holland skid steer loader’s throttle cable. I finally figured…
Read the complete tip →From the archive · Full text
Reader shop tip
James L. Fetzer, Maiden Rock, Wis.
“To remove the oil filter from my 2015 New Holland T4.75 tractor, I first have to remove the two fuel filters. Afterward, I have to call my neighbor – who is a service technician – to get the…
Read the complete tip →From the archive · Full text
Reader shop tip
James M. Driss, Lindley, N.Y.
“I had a manifold leak on the exhaust of my 2003 Ford F-150. To find the leak, I taped the nozzle on my shop vac to the tailpipe so it’s blowing into the exhaust system. Then I splashed…
Read the complete tip →From the archive · Full text
Reader shop tip
Jay Taylor, Hinton, W Va.
“In answer to the fellow who said the headlights on his 2000 Dodge Ram come on and won’t go off until he unhooks the battery, I think he may have put a single contact bulb into a double…
Read the complete tip →From the archive · Full text
Reader shop tip
Roger Gutschmidt, Gackle, N. Dak.
“The grain tank gearbox on my Deere combine, which moves grain from the clean grain elevator chain to the bubble-up auger in the hopper, failed a few years ago. A new one cost more than $2,000. The housing…
Read the complete tip →From the archive · Full text
Reader shop tip
Ted Lacey, Hay Manager, Trent, S. Dak.
“You can make an air preheater for gas or diesel tractors by taking heated air off the outside of the muffler and directing it through a pipe to the air cleaner. The preheated air goes down into the…
Read the complete tip →From the archive · Full text
Reader shop tip
Wayne Beggs, Lincolnton, Ga.
“I got tired of always having to pump up my wheelbarrow tire, not to mention the cost of replacing the tube. So I installed an old 16-in. steel wheel off an old piece of equipment. No more flat…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Brian Lough, Indian Head, Md.
“When repairing items with J-B Weld epoxy or other adhesives, I first apply a layer of epoxy. Then I place strips of storm window screen onto the epoxy to add strength to the repair. For even more strength,…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Brian Lough, Indian Head, Md.
“To keep penetrating oil from dripping away from seized or rusted fasteners and mechanical parts, I place cotton balls on the seized part and then saturate them with penetrating oil. This technique allows the oil to continuously penetrate…
Read the complete tip →From the archive · Full text
Reader shop tip
Frank Heraghty, Claremore, Okla.
“I had trouble trying to hold up a big extension ladder and guide it while raising the upper half of the ladder at the same time. So I came up with a simple and cheap solution. I inserted…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Jerry Lanser, Longmont, Colo.
“I have a 4 by 8-ft. freestanding workbench which works great, but there was never enough room to store commonly used tools close by.
Read the complete tip →From the archive · Full text
Reader shop tip
Jill Tuttle, Charlestown, N.H.
“I use ordinary plastic cups to keep the plugs on outdoor extension cords out of the weather. I cut a hole in the bottom of the cup, then slide the cord through until the plug is inside the…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
John Stuber, DeSoto, Mo.
“I use a lot of blades for utility knives and keep the blades in a jar. To prevent them from rusting, I spray clothes dryer lint with WD-40 and then place the lint in the bottom of the…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
John Stuber, DeSoto, Mo.
“Instead of buying a magnetic holder for my nuts and bolts, I make my own using a small can and magnets removed from discarded microwave ovens. A typical microwave oven has about 4 good magnets in it. I…
Read the complete tip →From the archive · Full text
Reader shop tip
Randolph Walker, Charlotte Court House, Va.
“After about 15 years of use, my Marlow irrigation pump wouldn’t prime any more. When I took it apart I discovered that not only was the seal on the impeller shaft bad, but also the shaft itself was…
Read the complete tip →From the archive · Full text
Reader shop tip
Roy Phlipot, Scott, Ohio
“When applying caulk or silicone, wear rubber gloves and coat them with liquid hand soap. Then use your finger to smooth out the caulk or silicone. It won’t stick to the gloves.”
Read the complete tip →From the archive · Full text
Reader shop tip
Ted Kalvitis, Romney, W. Va.
“Congratulations to the FARM SHOW reader who beat a proposed $1,800 repair bill when the clutch cross-shaft on his Kubota tractor seized in the bell housing. While he realized success with a mixture of acetone and transmission fluid,…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Lyle Mack
Lyle Mack loves gear making so much he’ll even help you make your own. The young machinist set up LM Gear and Machine on his family’s farm to make gears, sprockets, and splined shafts.
Read the complete story →From the archive · Full text
Feature story
Featured source: Bob Lenz
“I make parts for the throttle shaft and new oversize hardened weight pins for Farmall governors,” says retired farmer and governor repair specialist Bob Lenz.
Read the complete story →From the archive · Full text
Feature story
Featured source: Glen Wasmuth
Glen Wasmuth takes his tools to the job, whether in the shop or around the yard. His shop on wheels is loaded with tools of all sizes, from wrenches and bits to grinders, cutting torches, drill presses and…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Dustin Yoder
If you need a replacement seal, be it an O-ring, oil seal, rod wiper, piston seal, U-cup or other, Yoder Hydraulics probably has it in stock. If not, they can get it.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Steve Rea
Steve Rea and his company, Ploworx, produce tough-to-find fitted plowshares, moldboards, landsides and other parts for old and outdated plows. Rea says his company is one of the few anywhere in the U.S. or Canada to manufacture new,…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Randy Wyant
Precision Tractor Parts offers hard-to-find, U.S.-made parts for older International Harvester, Farmall and Cub tractors.
Read the complete story →From the archive · Full text
Reader shop tip
Allen Pederson, Nashua, Iowa
“You left out a crucial piece of information in your blurb in the last issue about how I attach a microwave magnet to a 3-ft. chain in order to pick up nails in the driveway and around my…
Read the complete tip →From the archive · Full text
Reader shop tip
Alvin Francis, Evansville, Wis.
“For the second time in 20 years, the rear axle on my Case IH 60 Series combine broke. It must be a common problem because our local dealer has a skid loader attachment designed to lift the rear…
Read the complete tip →From the archive · Full text
Reader shop tip
Bob Moty, Crystal Lake, Ill.
“I was a welder for 35 years and always kept a bottle of Vitamin E cream in my toolbox. Everyone in the shop would use it because it worked so well on burns and even cuts. I’ve seen…
Read the complete tip →From the archive · Full text
Reader shop tip
Carl Jolley, Monroe Twp., N.J.
“When filing a chainsaw chain, I mark the link I start on with chalk. Makes it easy to know when I’ve sharpened the entire chain.”
Read the complete tip →From the archive · Full text
Reader shop tip
D.S. Lindsay, Val Caron, Ontario
“I regularly fill old flat tires with expanding foam designed for insulating cracks in buildings. It works great on the right tires. You don’t use it on high-speed car or truck tires. But for tires used around the…
Read the complete tip →From the archive · Full text
Reader shop tip
Don Holzerland, Waubay, S. Dak.
I drill holes in wheel bearing caps to install grease zerks. Lets me grease bearings quickly and easily whenever I want. Haven’t replaced a bearing in a long time.”
Read the complete tip →From the archive · Full text
Reader shop tip
Doug Clark, Ilderton, Ontario
“I was reading my copy of your “Great Shop Ideas – Volume III” and came across an idea from a fellow who suggested adding a couple gallons of gas to the fuel tank of a worn-out diesel engine…
Read the complete tip →From the archive · Full text
Reader shop tip
Frank Brossart, Rugby, N. Dak.
“I converted an old gas grill that didn’t work any more into a portable table saw stand. I replaced the grill with a piece of 1/2-in. thick plywood and set the saw on top of it.
Read the complete tip →From the archive · Full text
Reader shop tip
Ken Siroky, Roy, Mont.
“I couldn’t see whether or not the twine was moving on my Vermeer 554 XL round baler so I wasn’t sure if the tying cycle was engaged or not. To solve the problem, I looped the twine around…
Read the complete tip →From the archive · Full text
Reader shop tip
Marge Simpson, Macon, Ga.
“You can sharpen old files by soaking them in sulfuric acid for several hours. It cleans them to like new condition and sharpens the edges.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Martin E. Matousek, Lake Geneva, Wis.
“After working on vehicle brake systems, I smear chassis grease on the brake bleeder screws and over the threads on steel brake lines and hoses. It seals them to keep out road salt and water. Next time you…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Martin E. Matousek, Lake Geneva, Wis.
“I made a transmission jack out of an old engine hoist to use under my car lift. A transmission cradle from Harbor Freight mounts on the end of a hand-pumped hydraulic cylinder off an engine hoist. It’s U-bolted…
Read the complete tip →From the archive · Full text
Reader shop tip
Murray Schrader, Adrian, N. Dak.
“We use anti-sieze compound when replacing bearings. Then the next time we have to replace them we don’t have to cut them off.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Paul Moore, Batavia, Ohio
“I had a problem with rust forming on the hydraulic cylinder on my moldboard plow. The cylinder is used to raise and lower the moldboard bottoms, and the chromed rod was exposed to dirt and rocks. I solved…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Paul Moore, Batavia, Ohio
“Oil began forming on the brake pads on my 1955 Minneapolis Moline 435 Mini Mo tractor. Roller bearings on both sides of the brakes were worn, which knocked out the seal between the transmission and brake shoes and…
Read the complete tip →From the archive · Full text
Reader shop tip
Phillip Taylor, Haleyville, Ala.
“You can make worn and rusty files like new by soaking them in white vinegar inside a glass gallon jug. Put the jug in a window so the sun warms the vinegar, causing it to bubble. Leave it…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Ron Byelich, Higgins Lake, Mich.
“My best advice to anyone when it comes to maintaining equipment is to look, listen, and keep things greased.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Ron Byelich, Higgins Lake, Mich.
“The best additions to my shop are steel-top work tables. They’re great to work on and you don’t have to worry about damaging them or burning them up.”
Read the complete tip →From the archive · Full text
Reader shop tip
Tony Ryba, Johnstown, Penn.
“I have a 2016 Ford F150 XL truck. Sometimes, when backing up, I’ll open the door and look behind me. The warning chime goes off and the warning lights come on telling me the transmission is not in…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Michael Merrigan
The cost of an expensive plasma table prompted Michael Merrigan of Hampton, Nova Scotia, to build his own out of a bathtub and some old bandsaw blades. The bathtub is screwed onto a 4-legged wooden stand with wheels…
Read the complete story →From the archive · Full text
Reader shop tip
Bob Payne, Coldwater, Miss.
“I bolted my stationary grinder onto an inexpensive 2-wheeler cart so that I can move it around wherever there’s good light and ventilation. The cart also makes the grinder easy to store out of the way. The base…
Read the complete tip →From the archive · Full text
Reader shop tip
Combined Manufacturing, Inc., Wildwood, Mo. (www.ezpourspout. com)
Their EZ-Pour Replacement Spout is designed to fit a variety of fuel and water containers that have some sort of safety spout automatic shutoff and no vent. Two threaded collars are included to fit most fuel cans, and…
Read the complete tip →From the archive · Full text
Reader shop tip
Garlon Peterson, Wild Rose, Wis.
“My old Sears riding mower sat around for a long time because the steering gear on it didn’t work. I finally got it fixed, but by that time the mower’s tires were flat from sitting so long. I…
Read the complete tip →From the archive · Full text
Reader shop tip
Jim Ellinger, Hanna, Ind.
“In a recent issue of FARM SHOW a reader said the Behr DeckOver coating he applied to his deck was peeling off. I think the problem was that he didn’t prep the wood properly. You have to pressure…
Read the complete tip →From the archive · Full text
Reader shop tip
Roger H. Keil, Bellevue, Iowa
“I used old 8-in. long railroad spikes to replace some of the worn-out teeth on a 10-ft. drag that I pull behind my roller harrow. The drag has 2 rows of teeth which are bolted to pipes. I…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Shawn Wagner, Plainwell, Mich.
“We had problems on my grandfather’s farm with panels on the combine breaking and cracking but were able to use JB Weld to solve the problem.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Shawn Wagner, Plainwell, Mich.
We also used it to repair a 2-in. shaft on my stump grinder. We filled in a worn out spot on the shaft and let the material harden, then used a lathe to turn it down. It has…
Read the complete tip →From the archive · Full text
Reader shop tip
Start Your Engines Fuel Systems Revitalizer, www.startyourenginesus.com (as printed)
This fuel system additive is designed to ensure easy starting of equipment that has been sitting for a long time (www.startyourenginesus.com; ph 773 376-4400). It works by adding combustibility to old fuel and removes gum and varnish sediment…
Read the complete tip →