Elden Reese
“I use a mixture of used motor oil and transmission fluid on rusted parts or bolts. After applying some, I soak an old sock and put it over the parts to keep them soaked.
Read the complete tip →5957 shop tips and stories · page 16 of 100, newest issues first.
“I use a mixture of used motor oil and transmission fluid on rusted parts or bolts. After applying some, I soak an old sock and put it over the parts to keep them soaked.
Read the complete tip →In fact, old socks often come in handy in my shop. They’re a good way to keep loose parts together.
Read the complete tip →“I bought a tilting car ramp from a car dealer going out of business for $175. I couldn’t build one for that. I set it up outside on a sloping concrete pad so it’s self-cleaning.”
Read the complete tip →“I learned the hard way that you should never buy the cheap 134a refrigerant that you see on sale all over the place. This stuff is mostly propane, which is why it’s so cheap at $4 to $5.…
Read the complete tip →“I had a belt that had been slipping on my riding mower for quite a while. I tried various belt dressings over the years without much luck. I went searching on the internet for a solution and came…
Read the complete tip →“When the metal body of my trusty old ShopVac rusted out, I got the idea of trying to fit the still-functioning vacuum onto the top of a plastic 5-gal. bucket. It was a perfect fit! The handle makes…
Read the complete tip →“Having a small shop, I don’t have a lot of room to attach tools to the floor – such as my metal bender, tire changer, vise, etc. So I put a pocket in the floor to accept posts…
Read the complete tip →You can update your Farmall tractor’s worn governor rockshaft bearings, seals, and bushings with Steiner’s new governor rockshaft repair kit. It’s designed to fit IH/Farmall A, B, C, Supers, 100, 130, 200, and 230 models. The 11-piece kit…
Read the complete tip →“When I buy products in aerosol cans, I write the date on the cans with a permanent marker so I can always tell which cans are older and use those up first.”
Read the complete tip →“I made what I think might be the world’s first 3-handed sandblast cabinet,” says Andy Sewell, North Yorkshire, England.
Read the complete story →“Our new flange bushing kit for planters makes old and worn parallel linkage arms and bushings work better than new. All the wear takes place on replaceable parts instead of on your planter’s parallel linkage arms,” says Dave…
Read the complete story →Minnesota handyman Mark Rinke bought a used Land Pride 4211 batwing mower that had issues with the gauge wheels, the wings, and the pto shaft and hitch. After he made improvements to all those components, the mower is…
Read the complete story →If you’re tired of dismantling half your Dodge pickup just to change the oil, you’ll like the new PacPro oil filtration relocation kit that moves the oil filter out into an open area for quick, hassle-free oil changes.
Read the complete story →“Our new Tailgate Sawhorse extends your pickup or utility vehicle bed by 3 ft. using only a pair of ordinary 2 by 4 boards. Your vehicle then becomes a portable workbench,” says Tyler Daly, Erickson Mfg. Ltd., Thamesville,…
Read the complete story →If you’ve ever had to remove baseboards, you know that damaging the wall can be a problem. Inserting a prybar behind the baseboard can easily punch a hole in the wall.
Read the complete story →Paul Bickford likes the weed control his rotary hoe provides. His homemade jig for replacing worn out spoke or tooth tips with Ho-Bit spoons (Vol. 41, No. 2) makes it even better.
Read the complete story →“I converted our 1978 Hefty-G cultivating tractor from a gas engine to electric motor drive,” says Reid Allaway of Tourne-sol Farm in Quebec.
Read the complete story →When Richard Batstone bought a 1953 Farmall Cub in the early 1980’s, he didn’t realize it marked the beginning of a new career for him. He spent 3 years restoring the well-used tractor.
Read the complete story →“I got tired of the coolant in my metal cutoff saw freezing so I decided to give RV anti-freeze a try. The pink stuff really works great with no freezing, no mess, no rust, and not much cost.
Read the complete tip →“Also, to remove aluminum buildup from an engine cylinder without filing or grinding, use some muriatic acid. Just dab it on with a Q-tip or eyedropper and it will dissolve the aluminum and not harm the sleeve.”
Read the complete tip →“I used a torch to cut a big notch in the pointed end of my shovel and then used an angle grinder to sharpen it. Makes the tough work of digging a little easier because the shovel can…
Read the complete tip →“A small squirt of starting fluid into the air intake will help start small gas engines that have not been started for a long period of time. The fluid will get you one or two firings which will…
Read the complete tip →“I mounted a garden hose reel on the top of my portable upright air compressor so I can put 50 ft. of air hose on it. Now I can easily reel and unreel air hose as needed.”
Read the complete tip →“The little screen in the bottom of a funnel came loose and ended up in the bottom of my fuel tank. Instead of throwing the funnel away, I made a big screen from some window screen and a…
Read the complete tip →“The 113-in. drive belt on my 60-in. Deere lawn mower deck stretched to the point that it was slipping. Rather than replace it, I installed a shorter tension spring on it and got 2 more years of use…
Read the complete tip →“Here’s how to make a handy siphon. Get a 1/4-in. copper tee, three 1-in. segments of 1/4-in. copper pipe, a rubber squeeze bulb, and a few feet of 1/4-in. rubber hose. Solder the copper tube segments to the…
Read the complete tip →“A lot of lawn mowers are hard to start. An older and wiser cousin of mine suggested sanding down the flywheel, cleaning the coil, and resetting the coil a bit wider. Presto! It worked!
Read the complete tip →“My advice to make your shop more efficient is to put everything on wheels or skids so you can move things around easily.”
Read the complete tip →“I was having trouble pouring tire balancing beads through valve stems into tires. I couldn’t pour, push or blow them into the tire until I started holding the side of an electric hair clipper against the metal part…
Read the complete tip →He’s a diesel mechanic at a shop that works with heavy diesel equipment such as loaders, bull dozers, and semi trucks.
Read the complete tip →“To avoid hitting electrical wires when drilling into walls, I just slip a small piece of pipe over the drill bit to keep the bit from going in too deep. Just make the
Read the complete tip →“I also came up with a way to use a regular electric drill as an impact wrench. I take a short socket wrench extension and cut off the end that fits over the socket wrench. Then I slip…
Read the complete tip →“The distributor on my Ford 8N tractor is hard to get at so my son Mike put a regular coil and condensor on the side of the block. He went right through the dead coil. Now, if the…
Read the complete tip →“Mike also fixed my wife’s wheelchair. The wiring was shot so I took it to two places in town but they wanted a lot of money to rewire the chair. Mike just cut off the ends of wires…
Read the complete tip →“Some farm equipment batteries are exposed to the elements, like on my IH 706 tractor. I cover them with rubber using an old tire tube to keep off dust, grease, and sunlight.”
Read the complete tip →“I bought a Depstech endoscope on Amazon for $38 and can’t believe how useful it is. It’s a 33-ft. length of tubing with a camera on the end that I’ve used to inspect dryer vents, plugged drains (it’s…
Read the complete tip →“Using a small amount of caulking from a tube usually leaves you with a tube full of hard, worthless caulking next time you try to use it. I’ve tried everything to seal tubes from putting a nail or…
Read the complete tip →Gene Boehler made an aerosol paint can “shaker” that makes use of an old cordless Ridgid sawzall, attaching a homemade shaker to the sawzall in place of the blade. A hose clamp attaches the can to the shaker.…
Read the complete story →“My 10-year-old Work Sharp knife sharpener does an excellent job (www.worksharptools.com; ph 800 597-6170). I can use it with 3 different sanding belts - an 80-grit to shape the blade and remove any knicks; a 220-grit to put…
Read the complete tip →“I sell a conversion kit that uses gear reduction starters to convert the 2-cyl. diesel engines on Deere tractors to electric start. It’s designed for Deere 70, 720, 730, 80, 820, and 830 models. Switching to a 12-volt…
Read the complete tip →“I turned a rolling walker into a handy, portable workbench. It’s sturdy, lightweight, easy to maneuver, and quickly folds up for storage. I used a piece of scrap aluminum to make the 16 by 24-in. top and screwed…
Read the complete tip →“I tipped over a wheelbarrow full of wood going into my woodshed,” Hohl says.
Read the complete tip →You can use a cordless drill to power this portable, lightweight winch that you can take anywhere. The Warn 500-lb. capacity winch comes with 30 ft. of wire rope with front and rear rigging hooks. A free spool…
Read the complete story →Overhead oil tanks, drip collectors and organized filters keep Howard Ewen’s shop clean and neat, making oil changes a lot easier. With 4 IH 4586 diesels, around 30 Olivers, 5 or 6 farm trucks, 3 pickups and several…
Read the complete story →The older the baler, the more likely its owner will end up calling Vernon Hershberger for parts and repair, or at least advice. Fixing balers is a big part of Hershberger’s farm equipment repair business. If a customer…
Read the complete story →If you’ve ever used a shop vac to dry out a flooded basement, you’ll be interested in this “quick connect” vacuum pump that hooks up to Ridgid vacs that have a drain. It lets you use an ordinary…
Read the complete story →Paul Petrocchi at American Windmill restores gear cases to better than new with a special oil seal and roller bearings.
Read the complete story →Scott Urschel is a bonafide expert in the repair, restoration and general maintenance of Cub Cadet lawn and garden tractors. Urschel’s Cub Cadet Connection business carries a large supply of new, used and reproduction parts for virtually every…
Read the complete story →“The traditional ‘motor-on-the-top’ air compressor that I got from a friend had a rusty 80-gal. tank and bad seals, so I decided to fix it up rather than throw it away,” says Mark Rinke, Lakeville, Minn.
Read the complete story →“Our new Ladder Lockdown saddle prevents almost all ladder movement to greatly reduce the possibility of accidental falls,” says inventor Troy Kumprey, Ladder Lockdown, El Segundo, Calif. Ladder Lockdown consists of an 8-lb., powder-coated steel saddle that serves…
Read the complete story →“Replacing a bad fuel line in a small plastic gas tank, such as on a weedeater, can be a difficult job. Over time the fuel line hardens and doesn’t seal properly against the hole where it enters the…
Read the complete tip →“I use an old drop-down lawn fertilizer spreader to apply asphalt sealer on my driveway. I cover all the holes in the spreader with duct tape, except for the metering holes at the bottom. I fill the spreader…
Read the complete tip →“When you’re drilling or milling metal, shavings which can fly everywhere and make a big mess. To catch the shavings that come off my drill press, I place a small magnet from an old car speaker on the…
Read the complete tip →“I used to have a lot of problems with gummed-up carburetors on equipment that gets used infrequently. I eliminated the problem by using Star Tron fuel enzyme before storage. It works much better than Seafoam or Stabil and…
Read the complete tip →“When the factory spring broke on my garden tractor’s shift lever, the lever wouldn’t stay in place. I came up with a quick fix by attaching a door spring to the housing in a way that keeps the…
Read the complete tip →“One of the handiest ideas I’ve added to my farm shop is putting in motion detector lights right by where I come in. Not only is it safer and easier when entering the shop, especially when my hands…
Read the complete tip →“I clean out used equine wormer tubes and fill them up with Anti-Sieze lubricant from NAPA auto parts and keep them in my tool bag. I use them to lube any bolt, shaft, or gearbox where rust or…
Read the complete tip →“I use old refrigerator produce drawers to store bolts, home clamps, springs, etc. They fit into shelves I made between studs in my shop.”
Read the complete tip →“I set up a battery charging station using an old Dewalt tool case. Using a rotary tool, I cut out the dividers in the case to make room for the chargers, which are held in place by a…
Read the complete tip →“Here’s a tip I learned a long time ago for an easy way to check points to see if you’re getting a good spark without turning the engine over with a key. Just pull the distributor cap and…
Read the complete tip →