Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW

Tools

5957 shop tips and stories · page 49 of 100, newest issues first.

From the archive · Full text
Reader shop tip 1 of 2

Larry Genge

Individual tip 1 of 2 from this reader’s published contribution.
Larry Genge, Glovertown, Newfoundland; ph 709 533-2798, [email protected]

“I built this 20-ton press from scrap metal, using 10-in. channel iron for the side posts and 6-in. channel iron for the bed. I can use 3 different sizes of interchangeable dies with it, ranging from 3/4 to…

Read the complete tip →
From the archive · Full text
Reader shop tip

Dick Clevenger

Dick Clevenger, 17174 County Road G40, Letts, Iowa 52754 (ph 319 726-3502)

“I’ve owned a 1955 Allis Chalmers CA with an L-306 Woods belly mower for 20 years. It’s pretty much bullet-proof except for one thing – if you move the adjuster idlers to tighten the belt, it’ll start wearing…

Read the complete tip →
From the archive · Full text
Reader shop tip 3 of 3

J.L. Findley

Individual tip 3 of 3 from this reader’s published contribution.
J.L. Findley, Letohatchee, Ala.

“I do the same thing to make a spark plug hole thread cleaner. Just cut off the electrode on a spark plug and cut an ‘X’ in the threaded end, file it down a bit, and insert into…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 3

Jeff King

Individual tip 1 of 3 from this reader’s published contribution.
Jeff King, Harwood, Md. (ph 443 506-9012)

“When fixing tires I use a skid loader-mounted forklift to break the bead. It works great because I can tilt the forks to almost any angle and slip them under the bead. The forklift only works to get…

Read the complete tip →
From the archive · Full text
Reader shop tip 3 of 3

Jeff King

Individual tip 3 of 3 from this reader’s published contribution.
Jeff King, Harwood, Md. (ph 443 506-9012)

“One shop tip I discovered is to put sheets of plywood down over the concrete floor. I just lay the plywood down without fastening it down. It’s a lot easier on my 70-year-old legs.”

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 3

Dennis Jannusch

Individual tip 2 of 3 from this reader’s published contribution.
Dennis Jannusch, Zimmerman, Minn.

“A few years ago a main drive sprocket broke in half on my forage box. I solved the problem by clamping the sprocket’s two broken halves back onto the shaft with a hose clamp and welding it –…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Ernie Oshust

Individual tip 1 of 2 from this reader’s published contribution.
Ernie Oshust, Star, Alta.

“I’ve tried all kinds of chain lubricants on our round baler without much success. Finally I tried Motul motorcycle chain oil, which seems to be a superior chain lube (www.motorcycle-superstore.com).

Read the complete tip →
From the archive · Full text
Reader shop tip

Louie Waelti

Louie Waelti, Monroe, Wis.

“I wanted to place an aluminum ladder up against my tractor’s hood without scratching it. So I placed a 5-ft. strip of 3/4-in. self-adhesive, auto body rubber trim on back of the ladder’s rails. Such body trim is…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Chad Travis

Individual tip 1 of 2 from this reader’s published contribution.
Chad Travis, Drasco, Ark.

“When re-sealing a paint can, take two layers of food-type cling wrap and place it over the top of the can. Then put the lid on. The plastic prevents metal-to-metal contact, making it easier to remove the lid…

Read the complete tip →