Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 34, No. 3 (2010)

Vol. 34, No. 3 (2010)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 36–39

37 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

William Snyder

William Snyder, Nauvoo, Ill.

“You can buy duct tape in various colors at Wal-Mart and Home Depot. It works great to repair cracked vinyl seats on tractors and other equipment. Much better than just using gray tape.”

From the archive · Full text
Reader shop tip

Carl Boutilier

Carl Boutilier, Freeport, Ohio

“I needed to make wheels for a school project and I needed them right away. I came up with a quick and easy way to make them out of wood scraps.

“I made a T-shaped holder out of wood that slides in the groove on the table saw. The piece that extends toward the blade has holes drilled 1 in. apart in it. I just put a pin in the center of a square block of wood, fit it into a hole, and then just push the piece of wood back and forth through the saw blade, rotating it a little bit each time until it’s perfectly round. This was a quick and easy way to make a wheel.”

From the archive · Full text
Reader shop tip 1 of 3

J.L. Findley

Individual tip 1 of 3 from this reader’s published contribution.
J.L. Findley, Letohatchee, Ala.

“I use hex nuts and bolts to make thread cleaners to clear rust and dirt buildup out of threads on any piece of equipment.

“To clean the threads on a bolt, I use a hacksaw to cut all the way through one side of a nut so it will expand to fit onto the bolt. I screw it on using oil or WD-40 to lubricate. Passing the nut over the bolt several times is enough to clean off most bolts.

From the archive · Full text
Reader shop tip 2 of 3

J.L. Findley

Individual tip 2 of 3 from this reader’s published contribution.
J.L. Findley, Letohatchee, Ala.

“To make a thread cleaner out of a bolt, I cut an ‘X’ in the end of the threaded end of a bolt and use a file to taper the threads at that end of the bolt. Helps it slip into a rusted nut or engine fitting.

From the archive · Full text
Reader shop tip 3 of 3

J.L. Findley

Individual tip 3 of 3 from this reader’s published contribution.
J.L. Findley, Letohatchee, Ala.

“I do the same thing to make a spark plug hole thread cleaner. Just cut off the electrode on a spark plug and cut an ‘X’ in the threaded end, file it down a bit, and insert into the hole to clear it out.”

From the archive · Full text
Reader shop tip

Robert Wilson

Robert Wilson, Hancock, Md.

“I have a lean-to attached to one of my barns that collapsed under a snow load. I needed a way to jack the roof back up for repairs. I got some square tubing (2 1/2 by 1 1/2 by 38-in. long). I slid it over the shaft on my barn jack and used it to lift up the roof. Worked like a charm. You could use tubing of any length to do this.”

From the archive · Full text
Reader shop tip

Greg Posch

Greg Posch, Holdingford, Minn.

“I got the idea because I was tired of opening drawer after drawer of my toolbox before finding the tool I wanted,” says Greg about his “Tools In Sight” stickers for toolbox drawers. Each of the 16 stickers shows a picture of a tool and its name.

“They’re helpful to me but also when I send my wife or kids to get me a tool. Makes it much more likely they’ll bring me what I asked for.” A set of 16 stickers sells for $10 including S&H. Contact: FARM SHOW Followup, Greg Posch, 39725 Co Rd 3, Holdingford, Minn. 56340.

From the archive · Full text
Reader shop tip

Dick Clevenger

Dick Clevenger, 17174 County Road G40, Letts, Iowa 52754 (ph 319 726-3502)

“I’ve owned a 1955 Allis Chalmers CA with an L-306 Woods belly mower for 20 years. It’s pretty much bullet-proof except for one thing – if you move the adjuster idlers to tighten the belt, it’ll start wearing because it won’t be perfectly lined up with the sheaves. It starts to scuff and wear itself out. This belt is 20 ft. long and rather expensive.

“The Woods people in Oregon were no help so I made my own tightener. It consists of a 2 by 4 by 16-in. piece of white oak with a 4-in. dia. idler pulley on one end and a 1/2-in. wide slot cut down the middle. A 2 degree taper is cut on the bottom of the wood so the pulley mounts at a slight angle to match the angle of the belt. That keeps the belt from wearing. Two bolts go through the slot at the center of the tightener. To tighten the belt, you just loosen the bolts and slide the pulley into the belt.

“In the past I was using 1 belt every year.

Now I get 5 years or more out of each belt, which I buy at Motion Industries (www.motionindustries.com) for about 1/3 the cost of belts from Woods.

“I think this idea would work on many other tractor mowers. I’d be willing to make these idlers for the cost of materials.”

From the archive · Full text
Reader shop tip 1 of 3

Jeff King

Individual tip 1 of 3 from this reader’s published contribution.
Jeff King, Harwood, Md. (ph 443 506-9012)

“When fixing tires I use a skid loader-mounted forklift to break the bead. It works great because I can tilt the forks to almost any angle and slip them under the bead. The forklift only works to get the bead loose from the wheel - I still have to use tools to get the tire off the rim.

From the archive · Full text
Reader shop tip 2 of 3

Jeff King

Individual tip 2 of 3 from this reader’s published contribution.
Jeff King, Harwood, Md. (ph 443 506-9012)

“My fabricating shop specializes in antique cars, and I don’t have a car lift. Instead, I use a forklift to put vehicles on top of four steel barrels. I can use one forklift to pick up a car, but if I’m going to work on a super-duty pickup I need two forklifts, one at each end of the vehicle.

From the archive · Full text
Reader shop tip 3 of 3

Jeff King

Individual tip 3 of 3 from this reader’s published contribution.
Jeff King, Harwood, Md. (ph 443 506-9012)

“One shop tip I discovered is to put sheets of plywood down over the concrete floor. I just lay the plywood down without fastening it down. It’s a lot easier on my 70-year-old legs.”

From the archive · Full text
Reader shop tip

Kenneth Hall

Kenneth Hall, Jamestown, N. Dak.

“The front wheels on my Bobcat Toolcat locked up so the machine wouldn’t move. I spent more than $1,000 at the shop to replace the disk brakes, but that didn’t solve the problem. Then I went online and found that someone in Ohio with the same problem had discovered the speed sensor was faulty. He solved the problem by simply unplugging the speed sensor. So that’s what I did, and now everything works. It would have cost $300 to replace the sensor.

“It’s getting to the point where I’m just as well off trying to fix my own equipment instead of taking it to the shop. The shop mechanics don’t seem to know much and waste a lot of money on stuff that doesn’t need fixing.”

From the archive · Full text
Reader shop tip

Travis Harrison

Travis Harrison, Leadwood, Mo.

“The hydraulics on my 1986 Prime Mover skid loader stopped working. Several people told me the problem was with the hydraulic pump, which I knew would be expensive to replace. I went to the internet for more information and learned that in most hydraulic systems there’s a screen in the reservoir where the fluid exits. I checked that screen on my skid loader and found that it was completely stopped up. After I cleaned the screen, everything worked fine.”

From the archive · Full text
Reader shop tip

Louie Waelti

Louie Waelti, Monroe, Wis.

“I wanted to place an aluminum ladder up against my tractor’s hood without scratching it. So I placed a 5-ft. strip of 3/4-in. self-adhesive, auto body rubber trim on back of the ladder’s rails. Such body trim is available at most auto parts stores.”

From the archive · Full text
Reader shop tip

David B. Dittmer

David B. Dittmer, Calhoun, Mo.

“The tracks on compact track loaders can freeze up in winter. We’ve found that cleaning the tracks, and then soaking the track system with recreational vehicle antifreeze, helps.”

From the archive · Full text
Reader shop tip

David Martin

David Martin, Hamlin, N.Y.

“I’m happy with the American Lubrication automatic oil dispenser that I installed in my shop (ph 888 252-9300; www.americanlube.com). It operates using air pressure and is equipped with a digital control meter that keeps track of how much oil is going out. It’s a lot easier to use than handling containers of oil when servicing tractors and trucks.

“The unit consists of an air-operated pump, a wall-mounted reel that hooks up to the pump, and a handheld dispenser equipped with an electronic digital meter. The pump mounts on my oil tank. To add oil to a vehicle I just grab the hose off the reel, bring it over to the vehicle, and pull a trigger on the dispenser. The electronic readout measures in quarts as I fill the vehicle with oil, and it’s right on the money. It’s a well-built unit.”

From the archive · Full text
Reader shop tip

Don Jaster

Don Jaster, Bruce, Wis.

“The company I work for has a Cat 257 skid steer loader, and the glow plugs on it didn’t cycle properly.

“While testing it I found the glow plug relay was an open circuit, so I replaced it with a new Cat relay which I bought for $28. It cycled about twice, but then the glow plug quit working. The problem was the contact had burned off the armature of the relay.

“I tested the glow plugs and found they each draw about 22 amps. The relay had about a 5-amp contact. I replaced it with a Ford starter relay that we already had. The new relay easily switches more than 300 amps. I made a Z bracket out of 1/2-in. strap metal to offset the larger size of the Ford relay. Note: A 1980’s GM diesel glow plug relay would work, too.

“I added wires to the Ford relay with that plug into the Cat’s original relay socket.

“Later on I learned about an owner of a 26X Cat skid loader that won’t start during winter because the glow plugs don’t work. Seems Cat has a design problem.”

From the archive · Full text
Reader shop tip 1 of 3

Dennis Jannusch

Individual tip 1 of 3 from this reader’s published contribution.
Dennis Jannusch, Zimmerman, Minn.

“My IH sickle mower kept plugging up at the end of the field when cutting short, thick grass. I solved the problem by welding 1-in. long pieces of welding rod at a 45 degree angle between the two rivet heads on the end section. The high end of the discarded rod faces toward the pitman, which makes the end self-cleaning.

From the archive · Full text
Reader shop tip 2 of 3

Dennis Jannusch

Individual tip 2 of 3 from this reader’s published contribution.
Dennis Jannusch, Zimmerman, Minn.

“A few years ago a main drive sprocket broke in half on my forage box. I solved the problem by clamping the sprocket’s two broken halves back onto the shaft with a hose clamp and welding it – even welding it onto the end of the shaft, figuring I can grind the sprocket off if I ever need to replace it. It’s still going strong.

From the archive · Full text
Reader shop tip 3 of 3

Dennis Jannusch

Individual tip 3 of 3 from this reader’s published contribution.
Dennis Jannusch, Zimmerman, Minn.

“I try to do most of my welding outside my shop on old metal barrels. The barrels are the right working height and are portable, and they keep the shop from filling with smoke.”

From the archive · Full text
Reader shop tip

Josh Hennings

Josh Hennings, Wickes, Ark.

“To fix broken splices on round baler belts I carry a bench-vise in my pickup. That way I can clamp the vise directly to the bale kicker and make splices right in the field.”

From the archive · Full text
Reader shop tip 1 of 2

Ernie Oshust

Individual tip 1 of 2 from this reader’s published contribution.
Ernie Oshust, Star, Alta.

“I’ve tried all kinds of chain lubricants on our round baler without much success. Finally I tried Motul motorcycle chain oil, which seems to be a superior chain lube (www.motorcycle-superstore.com).

From the archive · Full text
Reader shop tip 2 of 2

Ernie Oshust

Individual tip 2 of 2 from this reader’s published contribution.
Ernie Oshust, Star, Alta.

“To quickly and cheaply equip your workshop with work benches, buy some older-style steel office desks and place a 3/8-in. thick steel plate on top. You’ll have a sturdy work bench complete with roller drawers and storage cabinets.”

From the archive · Full text
Reader shop tip

Mark Newhall

Mark Newhall, FARM SHOW

“We’ve been impressed with Black & Decker’s ReadyWrench, a multisocket tool that fits 16 of the most popular standard and metric socket sizes (ph 410 716-3900; blackanddecker.com). Each 6-point socket fits a standard and a metric size, which means the ReadyWrench offers the same socket sizes as 16 different wrenches. Finding the right size is as quick as flipping one of the tool’s two rotating heads. Socket sizes are color-coded for easy visibility. The tool comes with a rubber grip handle.”

From the archive · Full text
Reader shop tip

Andrew Sewell

Andrew Sewell, North Yorkshire, England

Andrew likes these flat nose pliers made in England by Maun Industries Ltd. (ph 011 44 1623 554599; www.maun-industries.co.uk). The 6 1/2-in. long pliers are equipped with spring-return knurled jaws that always stay parallel, making it easy to hold objects for welding, etc.

From the archive · Full text
Reader shop tip

Alan Szynkowski

Alan Szynkowski, Cabazon, Calif.

“I have one of those home shop-type tire changing kits – an $80 manual set equipped with bead breaker, mount/dismount bars, etc. I take it with me on road trips where I almost always blow a tire or two. I welded a 2-in. sq. tube on the tire changer assembly that fits into my pickup’s receiver hitch. I also welded an extra receiver tube on the tongue of my trailer, which allows me to change tires on the road without having to drop the trailer. It works great and has saved me a lot of money over the years.”

Shop feature stories

From the archive · Full text
Feature story

“Made It Myself” Shop Air Filter

Featured source:

When Ron Isaac owned a welding shop, he made his own air cleaner by building a box lined with fiberglass insulation and fitted with a large ventilation fan.

“I got a lot of smoke in the welding shop, but this filter took care of it and also the fine dust,” he explains.

“A friend with a paint shop said the idea worked well for him, too.” Initially Isaac was concerned about fiberglass particles floating in the air, and there are some for the first couple of hours it’s used. But after that they vanish. Isaac built a 32 by 48-in. box with a 2 by 4 frame to hold a 1 1/2 hp fan. It can be a blade fan or squirrel cage fan, and Isaac suggests mounting the fan on rubber pads or springs to reduce noise. He nailed 1 by 2-in. (or smaller) slats every 6 in. on the inside of the box to prevent the insulation from pulling inside. He split the batt insulation to about 1 1/2 in. thick and slipped eight 4-ft. pieces between the 2 by 4’s all the way around the box. A piece of plywood covers the front with an opening for the fan. The entire unit is secured to the wall with lag screws.

“It pulls air in through the batts and blows clean air into the room,” Isaac says. He changed the fiberglass batts every three or four months as needed. As a test, he let a diesel tractor idle to the point where it filled the 40 by 60-ft. shed with smoke. He shut it off, turned the fan on and within 1 1/2 hours there was no diesel smoke. Contact: FARM SHOW Followup, Ron Isaac, P.O. Box 204, Hythe, Alta., Canada T0H 2C0 (ph 780 356-2727).

From the archive · Full text
Feature story

Rolling Stands Handy For Tractor Restoration

Featured source:

“I’ve seen many pictures in magazines where the tractors are sitting on blocks while being restored. That can be very dangerous and you can’t move them to clean the shop. With my carts, I can move tractor parts and frames wherever I need to paint or sandblast or just to get them out of the way,” says Bill Hinckley, West Bend, Wis.

“The first photo shows a rack I made to hold small parts while painting. It turns 360 degrees so you can paint and dry parts without touching them.

“The second photo shows a frame I use to work on garden tractors. After tearing a tractor down, I mount the frame in the stand to sandblast and paint. I just have to adjust the mounting brackets at either end to adapt to whatever tractor I’m working on. I actually assemble the entire tractor on the stand up until I put oil in the engine. Really works well because it’s at a comfortable working height.

“Photo three is a rack I use to paint wheel rims. It’s adjustable to any size wheels. It holds the wheel inside the rim and you can spin the rim around as needed to paint.

“Photo number four is a cart I made for tractor restoration. I’ve used it on 9 different models including Deere, Allis Chalmers, and Minneapolis Moline. The picture shows a Case tractor frame I’m working on. The back part of cart is from an old trailer running gear, flipped upside down with angles welded on for brackets to bolt to the rear axle. The front is tricycle wheels. I just revamp the brackets to fit different tractors.” Contact: FARM SHOW Followup, Bill Hinckley, 921 Birchwood Rd., West Bend, Wis. 53095 (ph 262-338-8404).

From the archive · Full text
Feature story

Best Penetrating Oil Is The Cheapest

Featured source:

Machinist’s Workshop magazine recently tested penetrating oils for break-out torque on rusted nuts. They “scientifically rusted” a bunch of nuts, treated them with various penetrants, and then measured the torque it took to remove them. Here are the results: • Nothing 516 pounds • WD-40 238 pounds • PB Blaster 214 pounds • Liquid Wrench 127 pounds • Kano Kroil 106 pounds • ATF-Acetone Mix 53 pounds The ATF-Acetone mix was a “home brew” mix of 50-50 automatic transmission fluid and acetone. Note that the “home brew” was better than any commercial product. Note also that Liquid Wrench was as good as Kroil for about 20 percent of the price. Thanks to reader Larry Heineman at L&G Products Co. (manufacturer of “Add-A-Stick” excavator extensions - www.add-a-stick.net) - for passing along this story.

From the archive · Full text
Feature story

“Solar Powered” Shop

Featured source:

Steven Ratliff, Spring Grove, Penn., used old sliding glass doors to build solar collector panels that he uses to heat his shop.

“It’s maintenance-free and keeps our farm shop comfortably warm at virtually no cost, even on the coldest winter days,” says Ratliff. The solar collector panels cover almost the entire south wall of his 30 by 60-ft. machine shop. They consist of a series of sliding glass doors on the outside, with a thin black plastic curtain to absorb heat behind them that hangs from a length of rebar. The 6-ft. sq. glass doors and the curtain mount inside a 2 by 10 wooden frame that bolts onto the side of the shop. There’s 12 in. of space between the window and the plastic, with cold air entering through a vent at each end of the 25-ft. long collector. The heated air is drawn in by a 2-ft. dia. louvered fan that sets inside a 1-ft. wide gap at the center of the plastic. The fan is hooked up to a thermostat and turns on whenever the temperature in the panel reaches 90 degrees.

“Even if the outside temperature is only 10 degrees, as long as the sun is shining the temperature in the shop will rise by at least 50 degrees during the day. In fact, when the sun is shining the furnace doesn’t even come on,” says Ratliff.

“I bought the sliding glass doors on Craiglist for $35 apiece. I open the windows to let the welding fumes out or whenever it gets too hot. In the summer I just slide the doors open all the way.” Contact: FARM SHOW Followup, S teven Ratliff, Ratliff Technical Services, Inc., 2818 Pine Tree Rd., Spring Grove, Penn. 17362 (ph 717 968-5366 or 717 744-1043; [email protected]).

From the archive · Full text
Feature story

Home-Built Hydraulic Press

Featured source:

When Don Ramberg needed a way to straighten snowmobile crankshafts, he built a 12-ton press. More than 30 years later, it can still handle any job he throws at it.

“It’s nothing fancy,” he says.

“I used 6-in. C-channel for the sides and top and steel plate for the press table and jack platform.”

Ramberg’s press stands about 6 1/2 ft. tall at its top. The side legs stand about 5 ft. tall. Holes drilled in the sides of the channel allow Ramberg to raise and lower the work table as needed. The work table consists of two pieces of channel iron with gussets welded in the middle and a steel plate laid on top of it. Simple pins hold the table in place until it needs to be moved.

Two more lengths of C-channel are welded across the top of the legs leaving a gap between them for the press post. Centered on these cross beams are two more C-channels about 18 in. in length with a third C-channel topping them off. The hydraulic jack that provides the pressure is housed inside this upside down U.

“The jack rides on a steel plate that fits inside the C-channel sides,” explains Ramberg.

“The steel plate is suspended on either side from the top of the compartment by two, 1-in. coiled springs that ride against the inside of the side C-channels.”

The press ram is, in turn, suspended from the bottom of the jack table. When hydraulic pressure is applied, the jack table and the ram are forced down. When pressure is released, the springs pull them and the jack upwards.

“I made the ram from a piece of tractor axle, boring out a 1-in. hole to hold different types of punches,” says Ramberg.

“A hole drilled in the side of the ram holds a spring and a ball bearing. The hole on the inside of the bore isn’t quite large enough for the ball bearing to come through, so it catches and holds punches when they are inserted. Punches are made out of 1-in. stock as needed.”

Ramberg welded a half moon of 5/8-in. steel over the top of the jack compartment to reinforce the top beam that takes half the pressure exerted by the jack. Two pieces of triangular shaped, 1/2-in. flat iron with 18-in. sides are welded to the bottom outsides of the two press legs. These “feet” stabilize the press.

“It’s pretty heavy,” says Ramberg.

“I’ve only moved it twice since it was built. It has worked well, and with the adjustable work table, I can handle large pieces. I do a lot of work on shafts for area farmers.”

Contact: FARM SHOW Followup, Don Ramberg, 33501 155th Ave. S.E., Mentor, Minn. 56736 (ph 218 637-2595).

From the archive · Full text
Feature story

Lawn Tractor “Rotisserie”

Featured source:

Gary Hast built a garden tractor “rotisserie” using a small photo from an old parts manual as his only guide. Hast built it for a Deere 110 tractor he picked up cheap that needed lots of work. He wanted to have a way to move it around easily to store out of the way between the times he had to work on it.

“Plus, doing the engine work was a pleasure - no backaches,” Hast says, because the tractor was off the ground about 30-in. He started with two inexpensive 750-lb. engine stands, and a worm gear and bull gear from a 1-ton winch.

“Bore out the bull gear to slip over the engine stand shaft and weld it,” Hast says. He welded it “sloppy” so it turns freely.

“Mount the gear drive below the bull gear.” He welded two nuts inside the arms of the engine stand and bolted it to the tractor’s front draft plate. For the back of the tractor, Hast welded short pieces of 1 1/2-in square tubing to the stand arms and bolted them to the tractor’s transmission. Hast notes he would make the tubing a couple of inches longer for more stability if he were to build it again. A piece of 1 1/2-in. square tubing connects the two stands. To create the right width for his 110 Deere, Hast cut an 18-in. piece and put 2 in. of both ends in the stands and bolted them. The length will vary according to the model tractor the rotisserie is designed for. Hast uses a hoist to lift the tractor to attach it to the engine mounts. He cranks the gear drive to turn the tractor in any position he wants. It holds without any extra locking system. While it worked out, Hast would make changes if he built it again. He’d buy better quality stands - ones with bearings would be the best. Hast spent about $200 to purchase the engine stands, winch and castors. He offers one last suggestion: Grease up the rotating parts of the engine stands so the plates spin easily - before you mount the tractor. Contact: FARM SHOW Followup, Gary Hast, 7334 Helms Circle, Pinson, Ala. 35126 (ph 256 609-7353; [email protected]).

From the archive · Full text
Feature story

“Larry Lugs” Revive Worn Rubber Tracks

Featured source:

The rubber track on a CAT/ASV skid steer may look like it’s in good shape on the outside, but if too many inner lugs break off, the track becomes useless. Bair Products Inc., in Louisburg, Kan., offers bolt-on replacement lugs that solve the problem.

“It can cost $1,400 to $2,300 for new tracks,” says Tonya Bair, co-owner of the company that specializes in after market parts for CAT/ASV and MTL skid loaders. Her father, Larry, invented “Larry Lugs” which are made out of a tough composite material. The individual lugs can be installed with the track on or off. You grind off the remainder of the broken lug. Center the template that comes with the lugs over the area and use a 1/2-in. drill bit to drill holes at a 90-degree angle. Place the lug’s washers on the outside of the track and alternately torque the bolts until the bolt heads are 3/16 to 1/4-in. embedded in the tracks.

“Each only takes about 10 minutes to install,” Bair says. Once installed the durable lugs extend the life of the track. And they outlast it.

“The great thing about Larry Lugs is that when the track becomes unusable, you can remove the lugs and reuse them on another track,” Bair says. Larry Lugs sell for $20 each, with volume discounts. They are available at CAT/ASV dealerships and at Bair Products, Inc.

Contact: FARM SHOW Followup, Bair Products Inc., 2785 West 247th St., Louisburg, Kan. 66053 (ph 913 947-3934; www.bairproducts.com).

From the archive · Full text
Feature story

Where To Buy Parts For Japanese Mini Trucks

Featured source: MacTown Mini Trucks

“Off-road” mini trucks from Japan have caught on fast since they were first imported 7 or 8 years ago. New dealers and importers have sprung up in many areas. Buyers like the price – often as low as $3,500 to $4,500. But finding parts can sometimes be a problem. Jimmy Johnson of MacTown Mini Trucks in McLeansboro, Ill., recently called FARM SHOW to say his company specializes in new, used and rebuilt parts for mini trucks including models such as Honda, Daihatsu, Mitsubishi, Mazda, Suzuki, and Subaru. They even manufacture some of the parts.

“We’ve been selling parts for Japanese mini trucks for 7 years and offer a wider selection of parts than almost anyone else,” says Johnson.

“One problem with getting parts for these trucks is they weren’t built for export to North America. As a result, the parts numbers for them aren’t of any help when you go to Auto Zone or Napa.

“I hear every day from people who couldn’t get parts anywhere else, and they’re elated when they find we can help them. We’ve gained a lot of knowledge about these little trucks over the years and are willing to share what we’ve learned with our customers. We also offer workshop manuals (in English) for sale on our website for anyone who needs them.” Other companies sell parts for Japanese mini trucks, says Johnson.

“However, most of them ask you to fill out a parts request form, which is then reviewed and sent off to Japan to see if the part is available and what it’s priced at. It can take two weeks to get a reply. Then the company calls you back and quotes you a price. As a result, it can take a month or more before you finally get the part. We’ll probably already have the part you need in stock. But if we don’t, we can usually get it within 7 to 10 business days.” The company stocks a wide selection of engine parts including engine rebuild kits, transmissions, hydraulic pumps, starters, alternators, water pumps, fan belts, bearings, oil seals, voltage regulators, manifolds, mufflers, clutches, steering shafts, ignition switches, glow plugs, brake shoes, filters and more, says Johnson. They also sell windshields, struts, doors, and CV axles. Other items for sale include “Camoclad” camouflage kits, which consist of permanent “peel-off” vinyl that adheres to the pickup’s surface to form a new camouflage skin for the truck. The company also manufactures and sells lift kits for 1999 to 2007 models. They also sell new and used trucks, wheels and tires, and bolt-on or weld-on bumpers with 2-in. receivers, as well as Blackline snowplows. Contact: FARM SHOW Followup, MacTown Mini Trucks, 100 S. Heard, McLeansboro, Ill. 62859 (ph 618 643-3373; [email protected]; www.mactownminitrucks.homestead.com).

From the archive · Full text
Feature story

Wireless Inspection Camera

By Jim Ruen, Contributing Editor
Featured source: Circuit Specialists, Inc.

You don’t need to tear an engine apart to check a cylinder wall for scoring or rip out a wall to check for bugs or water damage, thanks to new remote video cameras.

High-end video scopes have been available for sometime. What’s new is that instead of paying thousands of dollars, new scopes are priced in the $250 range.

When Circuit Specialists offered FARM SHOW the opportunity to try out an Aardvark video borescope, we grabbed it. I asked my mechanic, Herman Miller, and his crew to take a look at it. They were impressed, and so was I.

Miller, located in Fountain, Minn., already owned a scope he bought several years ago. When he saw the Aardvark from Circuit Specialists, he liked its features and its price tag.

“Ours was a lot more expensive, and the Aardvark does as much or more,” says Miller.

“We use ours to check under the hood for fluid leaks as well as to look inside the engine,” he adds.

“You can twist it around to see behind stuff and inside closed spaces without tearing everything apart.”

The Aardvark’s 3 1/2-in. wireless color monitor can be attached to the pistol grip camera unit or used separately up to 50 ft. away or more. The camera can be used for viewing as well as recording still and video of what’s being viewed. Interchangeable, flexible 9-mm and 17-mm shafts are available for use with the camera. The shafts are equipped with LED lights mounted at the lens to ensure clear viewing.

Using the Aardvark takes some practice as you learn to adjust the shaft to get the image right side up. The downloadable manual helped immensely, and the company’s help line operator actually had experience operating the unit.

Being able to capture video and stills for later playback via an SD card was very helpful. You can also connect the camera to a standard TV monitor or to a computer via USB cord.

The unit runs on four AA batteries, but also comes with an AC adapter. The basic Aardvark package is priced at $249. Similar packages are available from A&I Products, Milwaukee Tools and others. Prices and attachments may vary.

Contact: FARM SHOW Followup, Circuit Specialists, Inc., 220 S. Country Club Dr., Mesa, Arizona 85210 (ph 480 464-2485; toll free 800 528-1417; www.circuitspecial-ists.com).

From the archive · Full text
Feature story

He Built His Own Air Compressor

Featured source:

Eugene Schwanbeck couldn’t justify the cost of a new air compressor. So the League City, Texas man built his own.

“It’s built mostly from salvaged parts but looks like it’s new. I spent less than $500 to build it,” says Schwanbeck.

“Comparable commercial models sell for $3,000 or more.” He started with an 80-gal. tank that he fished out of a dumpster.

“It was a certified air tank so it still had many years of useful life left in it,” says Schwanbeck. He cleaned up the tank and repainted it. A 2-stage pump, which he got from his father-in-law, is driven by a 5 hp single phase, 220-volt electric motor that he bought new for $300. The air compressor is complete with a magnetic starter, automatic electronic drain valve, and low oil cut-off switch. All components mount on a rectangular frame made from 2-in. sq. tubing, with an expanded mesh safety guard.

“I’m happy with the way it turned out,” says Schwanbeck.

“I painted the air compressor Dewalt yellow and black and just for fun stenciled the Dewalt name on the tank because Dewalt is one of my favorite tool companies.

“I use it to operate tools in my home shop. My old compressor couldn’t keep up with my plasma cutter, but my home-built model can and now I can use it to operate a decent sized sandblaster, too. The pump and motor combination are rated for 17 cfm at 175 psi, which is a lot more capacity than I need.

“My biggest expense was for the motor and paint. The power cord and locking plug that I used came from a gas-powered generator, the conduit is from an outdoor patio project, and the expanded metal and steel tubing frame are left over from a shelving project for my garage.” Schwanbeck says the compressor has state-of-the-art features.

“The low oil cutoff switch ensures that if there’s not enough oil in the pump a circuit will open to prevent the unit from operating. And the automatic electronic drain valve prevents condensate from building up inside the tank and rusting it out. It’s a feature usually found only on industrial compressor models.” Safety wasn’t spared either, says Schwanbeck. The air compressor is equipped with 3 separate high pressure relief valves that protect the pump, the plumbing, and the tank.

“If the pressure gets to a certain point the valves relieve the pressure to prevent any components from exceeding their ratings,” notes Schwanbeck. Contact: FARM SHOW Followup, Eugene Schwanbeck, 420 Jessamine Way, League City, Texas 77573 (ph 281 483-0722 or 832 385-3322; [email protected]).

From the archive · Full text
Feature story

Portable Welding Cart

Featured source:

“It rolls easily on big wheels wherever I need to use it,” says Tom Chaney, Chrisman, Ill., who converted an old Roper riding mower into a towable welding cart. He got the junked riding mower, equipped with 18-in. rear wheels, from an uncle. He threw the engine away and cut the front end off, leaving only the frame, rear wheels and axle. He welded a 4 by 4-in., 1/4-in. thick angle iron onto the front of the frame and mounted a 10-in. caster wheel on it. Then he welded on a U-shaped handle between the rear wheels. He welded the original gearshift lever to the side of the frame, with a U-shaped length of rod on top, to hang welding cables and a welding helmet.

“The original welder could be bought with a cart, but it had small wheels,” says Chaney.

“I wanted a portable welder because I have a 3-pt. mounted generator on my tractor. Now I can pull my welder outside anywhere I want to go and hook it up to the generator. The top part of the mower frame consists of a flat metal plate, which I use to store tools.” Contact: FARM SHOW Followup, Tom Chaney, Sr., 14732 E. 1800th Rd., Chrisman, Ill. 61924 (ph 217 269-3507; [email protected]).