Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 34, No. 2 (2010)

Vol. 34, No. 2 (2010)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 36–39

32 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Lyndon Burkholder

Lyndon Burkholder, Hyde Park, Vt.

“When working on small engines, one particularly difficult procedure is to stabilize the flywheel to loosen the nut which holds it on. A friend shared this trick with me: Unscrew the spark plug and feed a small length of rope into the cylinder. I prefer a soft natural fiber rope rather than a plastic type. Also, be sure the rope is clean. The piston squeezes this rope against the head. This prevents the piston from going beyond top dead center, allowing you to tighten or loosen the nut.”

From the archive · Full text
Reader shop tip 1 of 2

Chad Travis

Individual tip 1 of 2 from this reader’s published contribution.
Chad Travis, Drasco, Ark.

“When re-sealing a paint can, take two layers of food-type cling wrap and place it over the top of the can. Then put the lid on. The plastic prevents metal-to-metal contact, making it easier to remove the lid next time.

From the archive · Full text
Reader shop tip 2 of 2

Chad Travis

Individual tip 2 of 2 from this reader’s published contribution.
Chad Travis, Drasco, Ark.

“Many late model tractors have FWD on the front. Replacing the kingpin, or trunion bushings as they’re called, can be a difficult job if you try to knock them out with a hammer and chisel. I have taken several out by welding. Take a bolt and taper grind the head so it will fit inside the bearing on the axle housing. Use a 3/32 stick rod 275 All-State series (chrome rods). They’re expensive but work well. After welding the head in place, put a nut onto the bolt and weld it into place. Put a length of 18-24 tubing or bar stock to be welded at midpoint onto the nut. Use two hammers of some size to hammer on the bar. The bearings will come right out.”

From the archive · Full text
Reader shop tip

Gene Ferencsik

Gene Ferencsik, Fruitport, Mich.

“I’ve read several articles in FARM SHOW about narrowing up a car rear end to make a new machine. But I’ve never read how they do it. How do you cut the axle and then weld it back together? How do you keep it lined up when welding it back together? Are there any special techniques used? What kind of welding rod is best?”

From the archive · Full text
Reader shop tip

Larry Wood

Larry Wood, Waldo, Ohio

“I had trouble changing the oil on my 2002 Ford F-150 4-WD pickup. I was able to get a good grip on the filter, but there wasn’t enough room to turn it or even work it loose with my filter wrench.

“To solve the problem I used a ratchet tie down strap. I wound the end of the strap up in my hand and slid it over the filter, then pulled the strap tight around the filter and attached the hook end to the pickup frame. As I started working the ratchet, the filter came loose very easily. Then I pulled on the strap, and the filter spun almost all the way off.”

From the archive · Full text
Reader shop tip

Verl Christensen

Verl Christensen, Preston, Idaho

“Here’s a time-saving idea that we use with our service truck. We carry various sizes of small bolts in pint-sized containers that we keep inside a larger metal box, which has a corner cut out of it. When we need to look for a bolt, we dump a container out into the larger box. After finding what we need, we dump the bolts back into the smaller container.”

From the archive · Full text
Reader shop tip

Ed Kaminski

Ed Kaminski, Townsend, Mt.

“Here’s an easy way to make sure you hook up the spark plug wires to the right cylinders when tuning an engine - just use clothespins. Number the clothespins in sequence, one for each cylinder, and attach them to the spark plug wires.

“The first thing I do after I open the hood is attach the clothespins to the wires. Then after removing the wires and installing the new plugs, I match the clothespins on the wires to the corresponding cylinders. When I’m done installing the spark plugs I just remove the clothespins and throw them in a toolbox, ready for the next time.”

From the archive · Full text
Reader shop tip

Wayne Gray

Wayne Gray, Hayden, Colo.

“When re-placing the clutch on a pickup you also have to replace the pilot bearing, which can easily get stuck in the flywheel. Unfortunately, most of the time you can’t fit a tool in behind the bearing in order to pry it out.

“To make it easier to pry the bearing out, I squirt three or four shots from a grease gun into the middle of the bearing. Then I find a punch that’s about the same diameter as the inside diameter of the bearing, and use the punch to force the grease behind the pilot bearing, which will then push the bearing out of the flywheel. It works almost like a hydraulic press. Electrical tape can be used to make a snug fit around the punch and the hole.”

From the archive · Full text
Reader shop tip

Tom Christensen

Tom Christensen, Blackfoot, Idaho

“Here’s an easy way to keep a handheld drill from injuring your wrist due to the counter torque when the drill breaks through. Just switch the drill’s trigger handle to your left hand right before it cuts through. That way the drill will pull out of your hand if it binds up, instead of banging into your right hand. This idea sounds almost too simple to work, but it does.”

From the archive · Full text
Reader shop tip

Janis Schole

Janis Schole, Pickardville, Alta.

“Here’s a tip for anyone who’s ever misplaced an owner’s manual for a product that was purchased a long time ago. You can usually find the manuals online and print them out. Just go to the manufacturer’s website and enter in the product’s information which is usually found on a plate somewhere on the machine.

“Going online for owner’s manuals is also a really good idea if you’re selling something at a yard sale. Having that manual sitting right next to the machine you’re trying to sell may make the difference in getting a sale or not. People are more likely to purchase a machine when there’s a manual with it. If you can’t find the manual on the manufacturer’s website, try googling the product name and model number.”

From the archive · Full text
Reader shop tip

Gary Callaghan

Gary Callaghan, Baie Saint Paul, Que- bec

“I couldn’t find parts for my Rockwell table saw or my Sears Craftsman molding head and knives, as both products had been discontinued. I looked on the internet and was able to find the companies that took over the old parts. I found that Ace Tool took over Rockwell, and Corbo Cutters took over Sears molding head and knives. The point is, don’t discard an old machine just because you can’t find replacement parts for it. Ask around and check on the internet first.”

From the archive · Full text
Reader shop tip

Paul Michener

Paul Michener, Grease Buster Tools, Waynesville, Ohio (ph 513 312-5779; [email protected])

“I recently introduced a new pneumatic version of the Grease Buster that’s called the Shop Size Grease Buster. The original Grease Buster, patented and made in the U.S. for 15 years, cleans out grease fittings and bearings using penetrating oil and hydraulic or pneumatic pressure. It’s the answer to the problem of plugged-up grease fittings and bearings.

“The new pneumatic piston (patent pending) for the Shop Size Grease Buster fits into a pneumatic hammer. I’ve used this tool to open frozen bearings that would otherwise have to be disassembled and cleaned to get lubrication into the fitting.”

From the archive · Full text
Reader shop tip

Steve Davis

Steve Davis, Performance Distributors, (ph 901 396-5782; www.PerformanceDistributors.com)

“Our new 404 International D.U.I. Distributor is the latest breakthrough in equipment ignition systems. The Davis Unified ignition is a one-piece, one-wire distributor. The high output Dyna-Module and 50,000-volt D.U.I. coil are located inside the distributor, making it virtually water, mud, and vibration proof.” The Dyna-Module and D.U.I. Coil work in tandem to produce a longer duration spark, allowing you to open up your plug gaps to .055. This burns your fuel more completely. The D.U.I. performs without a ballast resistor. Full voltage goes straight to your combustion chamber. Performance Distributors calibrates every D.U.I. on a distributor machine with a very accurate timing curve throughout the entire rpm range. This ensures instant throttle response when you “step on it.”

From the archive · Full text
Reader shop tip

Mac’s Custom Tie-Downs

Mac’s Custom Tie-Downs, (ph 866 371-5175; www.macscustomtiedowns.com)

They make a lightweight vise with full-sized jaws that installs in any standard hitch receiver and lets you make repairs right at your vehicle. The Trail D-Vise vise weighs only 17 lbs., yet has all the features of a full-size 8-in. vise, including high-grip cross-hatch jaws, a convex pipe holder and a built-in CNC-cut adjustment wrench. The compact design allows it to fit easily behind the seat of a truck or in most toolboxes. To use, just slide the vise into the receiver and tighten it down with the included Mac’s billet wrench. To prevent theft, the hitch pin can’t be removed without a socket or wrench once the unit is slightly tightened down in the receiver. The unit can also be mounted to a work bench using an optional square tube table receiver.

From the archive · Full text
Reader shop tip

James W. Proffitt

James W. Proffitt, Harrison, Tenn.

“Here’s an easy way to remove the spark plugs from the 5.4-liter gas engine on a Ford F-150 pickup. Loosen the plugs and spray around each one with WD 40. Let the plugs soak for eight hours, then spray more WD 40 around the plugs and start working the plugs back and forth in order to break the carbon. Apply more WD 40 while working the plugs back and forth.”

From the archive · Full text
Reader shop tip

Jeff Fox

Jeff Fox, Dacula, Ga.

“I used zip-lock ties to attach 2-ft. lengths of 2-in. dia. pvc pipe to the back screen of my Kawasaki Mule. I put my tool handles inside the pipes, so they stick up in the air rather than taking up space in the bed.”

From the archive · Full text
Reader shop tip

Jeff Lang

Jeff Lang, Newport News, Va.

“This drill press was built by my father Gilbert more than 60 years ago, and it still works. It’s made out of a Model T rear axle. A keyway was cut the length of the axle shaft so it could slide up or down through the gear. I don’t remember where the steering wheel came from, or the wheel rim the unit stands on. To start the press, I step on an old-fashioned starter button located on the wheel rim.

“A flywheel ring gear is used to move the drill chuck up or down. It was removed and straightened out, and an opposing gear had to be found to match. The press has only one speed – slow. The chuck can travel 12 to 14 in., and the narrow table is adjustable as well. I can still remember watching my father use this press in his farm workshop 40 years ago.”

From the archive · Full text
Reader shop tip 1 of 4

Roger Gutschmidt

Individual tip 1 of 4 from this reader’s published contribution.
Roger Gutschmidt

“I always wash my tractors and equipment before parking them for the winter. But this year, I did it a little differently.

“I bought a 2-gal. industrial hand pump sprayer (from Gemplers) that’s designed for spraying degreasers and solvents. Then, I dumped in 1 gal. of water along with 1 gal. of Citrol, which is a degreaser sold by Schaeffers Lubricants. I sprayed the mixture on my tractors wherever there was grease and grime.

“Doing it this way was much more economical than using spray can degreasers and I didn’t have to deal with all the empty spray cans. After the solution had a chance to soak in for 15 to 20 min., I just sprayed it off with water and it dried with no oily residue. A 2-gal. container of the mix was enough to presoak several tractors.”

From the archive · Full text
Reader shop tip 2 of 4

Roger Gutschmidt

Individual tip 2 of 4 from this reader’s published contribution.
Roger Gutschmidt

“I built these overhead ladder racks for my 6-ft. and 8-ft. stepladders. I was tired of leaning them against the wall or equip- ment, where they were always in the way.

“The racks were pretty easy to build and are made of 2 1/2-in. formed angle and miscellaneous flat straps for bracing. I made each of them in less than 1 hr. and they were inexpensive, as far as the materials I used. I painted them, and then bolted them to the ceiling of my loft area in my shop. They’re low enough that I can just reach up and pull the stepladders out.

“I really like them because now I have a bit more floor space and they’re still really handy and visible when I need them.”

From the archive · Full text
Reader shop tip 3 of 4

Roger Gutschmidt

Individual tip 3 of 4 from this reader’s published contribution.
Roger Gutschmidt

“Here’s a little hint for drilling holes in sheet metal or anywhere that large hole saws tend to “drift” away from the location you’re trying to drill (like in a piece of sheet metal).

For example, I recently installed a B&W brand turnover ball hitch in my pickup bed, and used this trick to make the hole-drilling easier.

“It’s pretty important that you get the hole exactly in the right place or the underside attachment brackets won’t line up. Although there’s a 1/4-in. pilot hole in the center, the hole saw still wanted to move around. So I used a simple piece of 1/2-in. plywood to solve the problem. It needs to be large enough to stand on to keep it in place. I use the weight of my body, but you can clamp it down too, if you’re able to.

“First, I drilled the size hole I needed in the plywood. This allowed me to see the metal through the hole. When you start to drill into the metal, the board acts as a guide for the drill bit, holding it perfectly in place.

“I also used this method to drill a hole in my rubber bed liner mat, which I installed in the truck box when I was finished installing the ball hitch.

“My brother Paul thought of this little hint. He reads FARM SHOW, so I have to give him the credit or I’ll hear about it.”

From the archive · Full text
Reader shop tip 4 of 4

Roger Gutschmidt

Individual tip 4 of 4 from this reader’s published contribution.
Roger Gutschmidt

“I like to have a place for everything, and everything in its place, so I hated having my cordless tool chargers sitting all over my work bench.

“To solve this problem, I found an excellent new place to store them. Since I always keep the lid of my big Sears Craftsman toolbox open, there was space on the inside of the lid where I could mount screws to hang them from. There’s actually a false panel that sits about a 1/2-in. from the actual lid of the box, and this allowed me to put screws through without having them come through to the outside of the lid.

“I have chargers for 3 cordless impact wrenches, 2 cordless drills, and a flashlight. Most of the chargers have keyhole mounts, so they hang on the screws, but some of them don’t, so I just have those setting below on the top tray of the toolbox. It’s a great, compact spot for everything, and I like having it all together so I don’t have to scrounge around looking for them. All of the cords are plugged into a nearby power strip. This idea cost me nothing and I love it.”

Shop feature stories

From the archive · Full text
Feature story

Power Cord “Plug-Proof” Bracket

Featured source:

Anyone who’s ever accidentally yanked an appliance cord out from an electric wall outlet will appreciate this V-shaped, wall-mounted bracket that “locks” the cord in place. Richard Layden says he came up with the idea after his wife complained about the vacuum cord pulling out of the electric outlet. The bracket is made from metal and simply screws to the wall on either side of the receptacle and slightly above it.

“Not only does it keep you from accidentally yanking the cord out, but it can be used to hold an extension cord between uses,” says Layden.

“Over the years I’ve given quite a few of these brackets away to friends and neighbors. I’d be willing to sell them if there’s enough interest.” The bracket sells for $3 plus S&H. Discounted price available for large volumes.

Contact: FARM SHOW Followup, Richard P. Layden, 11443 E. 4200 North Rd., Hoopeston, Ill. 60942 (ph 217 283-6864; [email protected]).

From the archive · Full text
Feature story

Parking Brake Latch For Farmall M’s

Featured source:

After reading a story about a quick latch for Farmall M brakes in FARM SHOW (Vol. 33, No. 1), Donald Jaster, Bruce, Wis., decided to improve on the idea. In the original story, Todd Quatier got tired of reaching down to lock the brakes on his Farmall M. He came up with a simple latch that allows him to use his left foot to trigger a lock on the brakes as he steps on them with his right foot. The unit is designed to use existing bolt holes in the transmission cover.

“I liked the idea, but the problem is your left foot is always busy on the clutch while your right foot is applying the brakes. I wanted to leave my left foot free. My design lets me use my fingertips right by the steering wheel,” says Jaster. A horizontal rod with a big bend in it runs across the floor from the steering column toward the brake latch. Another rod extends vertically from the horizontal rod up toward the steering wheel and has a big knob mounted on the top end that’s located about 2 in. below the throttle.

“When my hand is on the throttle I can pull up on the knob with my fingertips to trigger a lock on the brakes.”

The vertical rod bolts to the steering column with two bolts that go through a piece of angle iron with nuts welded onto it. A metal loop welded onto the horizontal rod forms a pivot point for the vertical rod. Jaster says the same idea would work on all IH tractors with the same basic H or M floor and brake system. Contact: FARM SHOW Followup, Donald Jaster, N5516 Johnson Rd., Bruce, Wis. 54819 (ph 715 868-8250; [email protected]).

From the archive · Full text
Feature story

Welding Rod Extender

Featured source:

Patrick Malloy’s welding rod “extends” helps each out-of-the-way spots. It’s adjustable from14 to 36 in. and you can add additional 6-in. extensions as needed. For Malloy, inventing the device let him return to welding.

“I was a welder until an accident put me in a wheelchair,” says Malloy.

“It lets me get the rod where I need to, even from my chair.”

The head swivels 180°. It seats rods up to 1/8-in. dia. without changing collet and tips. Adapters for larger rods are available. The thumb clamp has a quick connect/disconnect.

Malloy says the Expander, as he calls it, gives excellent control of the electrode. It also puts an end to jury-rigging rods to give them a little "added" reach.

“No more bending rods, breaking flux or welding rods together,” says Malloy.

The Welding Rod Expander sells for $69.95. Extensions (6-in.) sell for $10 each.

Malloy markets the device himself.

Contact: FARM SHOW Followup, Patrick Malloy, 101 Bunting Bridge Rd., Cookstown, N.J. 08511 (ph 609 758-8706; mobile 609 346-6150).

From the archive · Full text
Feature story

How To Upgrade Your Farm’s Electric Power

Featured source:

Variable frequency drives (VFD’s) let you use 3-phase motors without paying for 3-phase power. What’s even better, they provide infi - nitely variable speed control on big electric motors and the tools they drive.

“Three-phase power is typically 150 percent more efficient than single-phase and allows smaller motors to be used,” says Philip Myers, Myers Machine & Mfg.

These cost savings, explains Myers, are why 3-phase motors are used almost exclusively in industrial applications. As a result, used motors are readily available and economically priced. Myers frequently finds them in good condition for $5 to $10 per horsepower.

To use them, Myers buys VFD’s. They rectify incoming AC power to DC current and back to higher quality AC power that can be controlled.

“A VFD provides infinitely variable speed control, up to double or more than the 60 cycles the motor was originally designed to run at,” explains Myers.

“It also gives control of the rate of acceleration and deceleration with dynamic breaking and stopping. Another advantage is that torque doesn’t drop off as speed decreases.”

Standard single-phase AC induction motors switch on or off at full voltage supply. VFD’s let a motor develop 150 percent of rated torque while drawing less than 50 percent of rated current.

“VFD’s eliminate the need for gear reduction because of the way you can adjust the electrical power,” says Myers.

“We put them on all our shop equipment. It’s amazing to be able to easily adjust speeds.”

For a number of years, Myers used 3-phase motors on single-phase current by using static converters or rotary phase converters. However, when he switched his shop from manual controlled machines to CNC (computer numerically controlled) machine tools, the power provided by the converters wasn’t high enough quality.

“They required purer 3-phase power,” says Myers.

“The $24,000 estimated fee from the power company for bringing 3-phase power one mile to our farm provided the incentive to search for another solution.”

The answer Myers found was the VFD. He bought a 125-hp, 230V drive for about $6,000 and coupled it to a 50 kW, 480V, 3-phase generator. This gave him a dependable power supply for his entire shop at roughly half the cost of the electric company fee, plus it was a cheaper power with no extra demand charges.

Myers also uses individual VFD’s on each motor. He has used one drive on a 3-phase, 5 hp lathe for 14 yrs. with no problems. Myers cautions that drives and motors must be connected directly without a switch or transformer between them.

“Drive voltage must match that of the motor, and you need to use a drive with 30 to 50 percent higher hp rating than the motor if input is single-phase,” he says.

“The exception to that is 3 hp drives and under.”

Myers stocks used and new surplus drives from 1⁄4 hp drive with 115V single-phase input and 220V, 3-phase output for between $130 and $150, depending on enclosure.

“We’ve used these drives to power our Myers.

“My nephew uses one to provide variable feed and auto reverse on his band saw. A local fire department bought one to power their 3-phase siren. We’ve sold them Contact: FARM SHOW Followup, Myers Machine & Mfg., 587 Thomas Rd.. Holl-sopple, Penn. 15935 (ph 814 629-9632).

From the archive · Full text
Feature story

Solar-Powered “No-Hydraulics” Hoist

Featured source:

“My solar-powered portable boom hoist requires no hydraulics, and I can use it anywhere,” says Scott Knutson, Crookston, Minn. The hoist rides on four 10-in. high, 6-in. wide rubber wheels with another large single caster wheel on back. It measures 8 ft. long by 4 ft. wide. A 30 by 20-in. solar panel, mounted on top of the boom, charges a car battery that powers a 12-volt electric winch with a working capacity of 1,800 lbs. The operator grabs a 1-in. dia. pipe handle to move the hoist around. A voltage regulator monitors the battery so Knutson knows when it needs recharging.

“With the combination of the car battery and the solar panel for recharging, I can let the unit set outside or under the lights in my shop and it’ll charge itself. I never have to plug it in to recharge it,” says Knutson.

“I use the boom mainly to lift 15-gal.

chemical containers into my pickup or semi trailer. By pulling a pin I can adjust the boom’s height to different working levels. I also use it to mount quick hitches on tractors, to move combine concaves around the shop, and to mount weights on tractors. With the large caster wheel on back it’s easy to maneuver into tight corners.” Knutson says the solar panel he uses is typically used to charge RV units. He paid $150 for it.

“At the rate I use the lift, I can recharge the battery in only about 2 1⁄2 hours,” he notes. Scott and his brother Curtis also own KB Mfg., LLC, through which they sell other products that they use. The company’s website is www.rrv.net/kbmfg/Contact: FARM SHOW Followup, Scott Knutson, 31109 290th St. S.W., Crookston, Minn. 56716 (ph 218 281-6426; [email protected]).

From the archive · Full text
Feature story

He Built His Own Car “Rotisserie”

Featured source:

“I built it by borrowing the best ideas I could find in catalogs and on the internet. My total cost was about $300, which is only about 1/4 as much as commercial models sell for,” says Tim Hays, Oreana, Ill., about his home-built, portable car “rotisserie”. It lets him rotate a car body 360 degrees so it’s easier to work on. The unit mounts on six 4-in. caster wheels and is equipped with a pair of telescoping steel rails supported by a 3-pt. stand at each end. Tim places the car body on rails and fastens it in place. After that he can easily rotate the car body to either a 45 or 90 degree angle, and then insert a pin to hold the car where he wants it. When he’s done working on the car, he can roll the entire unit off to the side and work on something else.

“It makes the car much more accessible and eliminates the need to crawl under the vehicle,” says Hays.

“It allows me to securely bring the car to the desired height, then rotate it to the best angle for whatever I need to do to the car. I use a ‘pivot bar’ on one of the 3-pt. stands to rotate the car. It’s so well balanced that even my 9-year-old daughter can easily turn it over with one hand.” Contact: FARM SHOW Followup, Tim Hays, 512 N. East St., Oreana, Ill. (ph 217 468-2530; [email protected]).

From the archive · Full text
Feature story

Roll-Up Tarp Protects Metal Lathe

Featured source:

Roger Gutschmidt wanted to keep dust and dirt from collecting on his metal turning lathe, so he set up a roll-tarp to protect it when it’s not in use. Four pieces of 3/4-in. metal conduit, each bent to an L-shape, hold the tarp over the machine. The two outside “support bows” are statio-nery while the two center supports are held in place by strong magnets on top that stick to metal plates attached to the wall. The bottom of each removable support has a large flat washer welded to it to act as a free standing “foot.” Gutschmidt had the tarp specially made to fit at a local shop, so that it just touches the floor when fully extended.

“The tarp has a long pocket at the top end with a 1-in. dia. pipe through it. That pipe is screwed to the wall,” he explains.

“In a pocket at the bottom of the tarp, there’s a bigger 2-in. dia. pipe, which allows me to manually roll it up faster. The size and weight also makes it unroll quickly.” The roll-tarp dust cover measures about 4 ft. tall by 3 ft. deep by 11 ft. wide. According to Gutschmidt, the custom-made tarp cost him $160, the bow material was $30, and with the rest of the supplies, the project came to around $250. Contact: FARM SHOW Followup, Gutschmidt Manufacturing LLC, Roger Gutschmidt, 6651 Hwy. 56, Gackle, N. Dak. 58442 (ph 701 698-2310; [email protected]).

From the archive · Full text
Feature story

Brake Rotor Makes Great Base For “Third Hand”

Featured source:

With a little ingenuity and some scrap steel, Mike Erdelen of St. Charles, Mo., made a handy and inexpensive “third hand” work support for his auto repair shop. His idea can be adapted to practically any shop. The unit consists of a larger pipe welded to a brake rotor that serves as a base and a smaller pipe that telescopes in and out and is welded to a U-shaped plate that supports the work. To hold the tool at the correct height, Erdelen welded a 3/8-in. hex nut over a 1⁄2-in. dia. hole drilled near the top of the base pipe. A 3/8 by 2-in. bolt threads into the nut to act as a set screw. To make the set screw easy to tighten by hand, he welded a short rod across the head of the bolt. Depending on your needs, you could build a tall “third hand” like the one shown in the photo, or scale it down to hold work at any comfortable height.

“I like this unit because it doesn’t have a large tripod base like commercial units,” says Erdelen.

“It’s a lot easier to work around this one.” Contact: FARM SHOW Followup, Mike Erdelen, Fred’s Car Care, 1130 First Capitol Dr., St. Charles, Mo. 63301 (ph 636 946-1446).

From the archive · Full text
Feature story

Auto Light Helmet Helps Welders See

Featured source:

Kenneth Schwanz has a kit to brighten up a welder’s day or night. His Auto-Light LED’s follow a welder’s line of sight, always keeping a light on the welder’s work.

“My Auto-Light is mounted on my helmet and activates when the face shield drops and shuts off when the shield is lifted,” he says.

“It has a separate switch for use as either a spot or a floodlight. It can also be tilted up or down 120°."

Auto-darkening helmets are great when welding, but still leave welders too much in the dark before and after the weld. This is especially true if working in dark spaces or at night.

The Auto-Light floodlight produces a circle of light 10 to 12 in. in diameter. The spotlight sends a beam out from 10 to 30 ft.

"It will light up a room when totally dark," says Schwanz.

A retired electrical engineer, Schwanz got the idea from area welders who complained about poor visibility. Schwanz's son, a professional welder, used a prototype for three months in a production shop and gave it high marks.

"Other welders tape flashlights to their helmets or hold them in their mouths or have to ask a second person to hold a light," says Schwanz. "My son was doing welding for military, emergency service and fire engine production contracts. Welds had to be good, and the light really helped."

Schwanz estimates a kit including the spot/floodlight, rechargeable battery pack and plug inlet for recharging overnight would sell for no more than $225. He has designed the light system so it could easily be installed on most popular welding helmets.

The prototype uses four nickel metal hydride batteries and lasts for about 6 hours of steady use. It’s equipped with a smart charger that automatically shuts off when fully charged.

He’s currently looking for a manufacturer to take on the project. He hopes to license it in the near future.

“I think it would as useful on the farm as in the shop,” says Schwanz.

“It will help anywhere hands-free light is needed.”

Contact: FARM SHOW Followup, Kenneth H. Schwanz, 836 Ridgeview Ct., Portage, Wis. 53901 (ph 608 742-3161; [email protected]; www.kesslercorp.com).

From the archive · Full text
Feature story

New Tools Fit Reciprocating Saw

Featured source:

A reciprocating saw works great for cutting wood or metal, but by adding this new adapter you can also use the same saw for brushing, sanding and filing work. Tools attach quickly to the Reciprotools adapter. Depending on the attachment, a reciprocating saw can be used as a blade sharpener, a hole enlarger, a wood shaper, a paint and rust remover, or a fast way to clean crud off your barbeque grill. And because the attachments are hex-shanked, you can rotate the attachment to make whatever job you’re doing easier. The adapter sells for $18.49 plus S&H; the attachments sell for $6.99 to $8.99 plus S&H. Available attachments include steel and nylon brushes, cleaning pads, rasps, and a variety of files. Contact: FARM SHOW Followup, Reciprotools, L.L.C., P.O. Box 80145, Saukville, Wis. 53080 (ph 262 675-0807; www.reciprotools.com).