Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 25, No. 2 (2001)

Vol. 25, No. 2 (2001)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 38–41

32 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Rich Bednarski

Rich Bednarski, 215 South Buffalo Rd., Washington, Pa. 15301 (ph 800 832-6350 or 724 345-3546)

“I can supply all the parts necessary to rebuild mechanical-style torque amplifiers found on old International Harvester tractors made in the 1950’s and early 1960’s, and I can also rebuild them. My torque amplifier parts are less expensive than the ones sold by most implement dealers. If you want the unit rebuilt, most of the time I can rebuild it cheaper than you can buy a re-built unit from someone else.

“The tractor models include the Farmall Super MTA and models 300, 350, 400, 450, 460, 560, 666 and 686. The price to rebuild an amplifier depends on the parts that are needed and can vary from $110 to $400. Re-built units come with a 5-year warranty.”

From the archive · Full text
Reader shop tip 1 of 2

Joel Waldner

Individual tip 1 of 2 from this reader’s published contribution.
Joel Waldner, Lethbridge, Alberta

“We use a homemade, portable battery cart to jump start cars, trucks, and tractors. It eliminates the need to start up another vehicle and is really handy to use. The batteries sit inside a wooden box mounted on a metal frame, and there’s a handle at one end. The cart rides on two big rubber wheels which makes it easy to pull. A telescoping leg supports the front side of the cart. If we need a lot of power to jump start the vehicle, we can hook up both batteries at the same time. A compartment on front of the box can be used to store booster cables as well as a battery tester.

From the archive · Full text
Reader shop tip 2 of 2

Joel Waldner

Individual tip 2 of 2 from this reader’s published contribution.
Joel Waldner, Lethbridge, Alberta

“We also came up with our own portable wood working table that makes it easy to clamp and glue together pieces of wood. The working area is 4 ft. off the floor which is much easier than working on the floor. An-other advantage is that the clamps are held firmly in place by the table.

“The metal table is 4 ft. wide and 6 ft. long and mounts on four caster wheels. The 4-ft. long clamps on top of the table are spaced about 8 in. apart and fit through holes drilled into one side of the table. The handle end of each clamp has a hole drilled into it, allowing the clamps to be fitted over small metal tabs welded onto the opposite side of the table.

“A 3/4-in. plywood shelf below the top of the table is used to store extra clamps.”

From the archive · Full text
Reader shop tip

Leonard Seltzer

Leonard Seltzer, Manhattan, Ill.

“I used a couple of Army surplus wooden ammuni-tion boxes and 2 by 4’s to make a low-cost, double stacker toolbox. I bought the boxes at a gun show for $5 apiece. The boxes measure about 3 ft. long and 1 ft. wide. I used screws to attach the legs to the boxes. The boxes came with hinges and a rope handle at each end. I screwed 1 by 4 wood spacers on the back side of the boxes, allowing me to raise the lids and prop them up with metal rods.

“I use the boxes to store heavier tools such as pipe wrenches, plumbing tools, big hammers - anything that would otherwise bang up an expensive commercial metal toolbox.”

From the archive · Full text
Reader shop tip

Ronald Lubke

Ronald Lubke, Quality Metal Works, Inc., 101 N. Division St., Stanford, Ill. 61774 (ph/fax 309 379-5311)

“I’ve recently begun marketing an electric cord winder that really works neat. The Wonder Winder is a heavy duty plastic housing equipped with a crank on one side, and a nylon net underneath it for storing the cord. One end of the cord extends from the bottom of the net and plugs permanently into a wall outlet. To wind up the cord, you just wind it back up inside the net. You do that by pushing back on a lever on top of the housing and then turning the crank. The lever pushes the cord against a wheel inside the housing so that the cord comes out the bottom of the housing and winds up neatly inside the net. The crank can be mounted on either side of the housing.

“It keeps the cord up off the floor, stored neatly inside the net. The cord always stays plugged into the wall so you never have to unplug it. The net can store up to 150 ft. of cord. It takes only about 30 seconds to wind up 100 ft. of cord. It’ll handle cord sizes from 16 ga. on up. It mounts with one pin to a bracket. By ordering more than one bracket you can easily move it from place to place. Sells for $22.95 plus S&H.”

From the archive · Full text
Reader shop tip

Duane McHenry

Duane McHenry, Rt. 2, Box 302, Clyde, Kansas 66938 (ph 785 446-3554)

“I operate an irrigation supply business and also an aluminum welding business. To make it easier to straighten out gated pipe with dents in it, I came up with a portable pipe straight-ener. It works on anything that has a round tube, including grain augers and combine unloading augers.

“My pipe straightener rides on four wheels and is about 25 ft. long. I started out with a scissors jack and welded two steel pans onto it, one at the top and one at the bottom. The jack mounts at one end of a 20-ft. length of sq. tubing that’s mounted inside a pipe. The jack is operated by a hydraulic cylinder mounted at the other end of the tubing. I place one end of the bent pipe on a stand and slide the bent portion of the pipe over the jack, then use a 2-way control valve mounted just above the jack to operate it. One way pushes the top pan up and the other way pushes the bottom pan down. I can reach 20 ft. into a pipe. Most gated irrigation pipes are 30 or 40 ft. long so by turning the pipe around I can straighten out the entire pipe.

“The cylinder is operated by a car power steering pump that’s belt-driven by a 1 hp electric motor. I can bolt on different size pans according to the pipe size. The unit has a handle at one end, allowing one person to push it in or out of my shop.”

From the archive · Full text
Reader shop tip 1 of 2

Profi Magazine

Individual tip 1 of 2 from this reader’s published contribution.
Profi Magazine, www.profi.com

Here are a couple ideas we recently spotted in Profi, a do-it-yourself farm magazine published in England.

Have you ever wanted hot water out in the field? British farmer Philip Partridge of Ipswich mounted a 1/2-gal. metal tank on the side of his tractor engine, just below the exhaust manifold. The engine heats up the water, which is released by a small spigot below the tank.

From the archive · Full text
Reader shop tip 2 of 2

Profi Magazine

Individual tip 2 of 2 from this reader’s published contribution.
Profi Magazine, www.profi.com

When you have to clamp a bolt in a vise, most people try using wood or some other soft material to avoid damaging threads. But that often does not provide enough gripping power. Another alternative is to cut a slice out of the side of a nut, and then screw the nut onto the bolt and clamp it into the vise. The nut will clamp down on the threads without damaging them, holding tightly. When the vise is released, the nut will screw right off.

From the archive · Full text
Reader shop tip

Roger Kuntz

Roger Kuntz, K-Tech, 5251 County Road X, Grainfield, Kan. 67737 (ph 785- 673-5560)

If you’ve got a blade plow, chances are at one time or another you’re going to need a replacement turnbuckle, says Roger, who makes an extra heavy-duty replacement for Flex-King, Richardson, and Noble blade plows.

“It features a massive 1 1/2-in. hardened right and left hand threaded screw for ‘on plow’ easy leveling. It’s far stronger and less costly than original equipment and comes with leveling instructions. Sells for $69.95, including shipping.”

From the archive · Full text
Reader shop tip

Bob Hudspeth

Bob Hudspeth, Era, Tex.

“I was surprised to see the article in your last issue on the 3-headed box-end wrench because on the day I read it, I had a similar wrench all clamped together in my shop ready to be welded. I had already made another special tool out of a pair of pliers and three box end wrenches. I added 9/16, 1/2, and 7/16-in. wrenches to the handles of an ordinary set of pliers. It lets me make minor adjustments and repairs to many pieces of equipment without going to the shop for a handful of various tools. An added benefit is that the box ends also make the pliers easier to hang onto. They also add extra leverage for extra tight nuts and bolts.”

From the archive · Full text
Reader shop tip

Craig Saugstad

Craig Saugstad, Minot, N.Dak.

“In a recent issue of FARM SHOW, a reader took issue with a previously submitted method of breaking beads on tires by driving up on them. I have a different method that involves a handyman-type jack or hydraulic jack. Just lay the tire under a heavy, immovable object such as a grain truck or pickup, and put the foot of the jack on the sidewall of the tire, right next to the bead. When you jack up against the vehicle, the foot of the jack will break the bead.”

From the archive · Full text
Reader shop tip

Farley Cole

Farley Cole, Girard, Ill.

Farley needed a hydraulic press in his shop so he made one out of parts salvaged from an old truck frame. He welded the pieces of heavy channel iron into a house-shaped frame with a pair of crossbars. He runs the press with a conventional hand jack. On one side of the frame, he mounted an old time drill press, powered by an electric motor on top of the press frame.”

From the archive · Full text
Reader shop tip

Dale Simon

Dale Simon, 1993 E. 1650 th St., Coatsburg, Ill. 62325 (ph 217 936-2459; Website: [email protected])

“I used parts from old photocopy machines, including the electric motor, rollers, bearings, chains and sprockets, to make a tumbling parts cleaner. It’s not very high tech but it works great. It uses two rollers, spaced 5 in. apart, inside a plywood box. One of the rollers is chain-driven by the motor while the other roller rotates freely. I put the parts I want to clean into a 1/2-gal. plastic jar along with some degreaser and some drywall screws or 1/4-in. square nuts that act as an abrasive to help clean the parts. Then I place the jar between the two rollers and let it tumble for a while. The parts come out nice and clean. To give the jar more ‘traction’ against the rollers I place large rubber bands around it.

“I made a second model using a smaller 1/ 8 hp electric motor and rollers made from 5/ 8-in. dia. wooden dowels covered by rubber hose. The motor is geared down by a jackshaft so the jars don’t turn too fast. I use a 1-gal. jar with this model. I also mounted a mechanical counter on it. I let it roll 70,000 rounds or about 7 to 8 hours. The motors on both models are cooled by small computer fans.

“I had a problem with some of the contents sliding rather than tumbling inside the jar. To solve the problem I wedged a block of wood or wire mesh inside the container. I plan to make another model using a 5-gal. bucket, which would be big enough to clean couplings clevises and old antique tools.”

From the archive · Full text
Reader shop tip

Lloyd Meffert

Lloyd Meffert, Hettick, Ill.

Lloyd built this foldup tire changer to conserve precious floor space in his shop. He uses it to repair all sizes of tires from lawn mower on up. He built a hinged frame that bolts to the base of his overhead crane. When he needs to work on a tire, he just folds it down.

From the archive · Full text
Reader shop tip

Bayard Young

Bayard Young, Elkwood, Va.

“I used to have problems losing my place when working on corn picker chains, and other chains like that. I solved the problem by keeping a small can of paint handy to mark the master link. Lets me know at a glance where I’m at.”

From the archive · Full text
Reader shop tip

Carmen Mawson

Carmen Mawson, Ardmore, Alta.

“Replacing the clutch spring on Case 1070 tractors is tough. I came up with an easier way to do it. Simply fill each ring of the spring with washers. Then put the spring in place and step on the clutch. All the washers will fall out and the spring will stay in place.”

From the archive · Full text
Reader shop tip

William Fazer

William Fazer, Powers, Mich.

“I salvaged an old computer desk to make this portable storage unit for my Lincoln wire feed welder. A hole cut near the back of the top shelf allows the CO2 tank to set on the lower shelf. The bottom of the tank is held in place by small strips of wood. Pegboard on the rear of the lower storage area holds spare tips, spools and small parts. To handle the extra weight, I replaced the plastic casters with steel wheels. I also added two small handles to the top of the unit to make it easy to roll the cart out from under the workbench.”

From the archive · Full text
Reader shop tip

Kevin Gogerty

Kevin Gogerty, Hubbard, Iowa

Here’s how Kevin keeps his Deere cornhead looking like new. Each year, before putting it away for the winter, he cleans it up good and then gives it a light coat of John Deere green paint using an aerosol spray can. He says it’s quick and easy to do and prevents corrosion from taking hold.

From the archive · Full text
Reader shop tip 1 of 2

Pete Peters

Individual tip 1 of 2 from this reader’s published contribution.
Pete Peters, Osler, Sask.

“I made a nifty funnel stand that avoids the mess of storing oil funnels on your workbench. It consists of concave discs mounted - curved sides down – on an upright piece of pipe. Then you drill a drain hole in the bottom of each disc so oil drains from each disc down to the one below it. You just put the empty oil container in the disc to drain. The bottom of the funnel stand sets in a metal or plastic tray to catch the oil that drips out. I also put some hooks at the top of the stand to hold grease guns.

From the archive · Full text
Reader shop tip 2 of 2

Pete Peters

Individual tip 2 of 2 from this reader’s published contribution.
Pete Peters, Osler, Sask.

“Here’s a jack attachment that I use for removing transmissions. It fits onto a standard floor jack. It consists of a flat metal rack made from short pieces of strap iron. A metal shaft fits down into the jack. It slips on and off as needed. Quick and simple.”

From the archive · Full text
Reader shop tip

James L. Evans

James L. Evans, Hammond, N.Y.

“On a Ford 6610 tractor, the driveline for the front wheel assist is covered by a heavy shield. To grease the universal on the front you have to drop the shield. It’s very time consuming to get back on. I solved the problem by cutting a 4-in. hole under the universal. Now it’s much easier to keep greased.”

From the archive · Full text
Reader shop tip

Roy Crane

Roy Crane, Martinsvile, Ill.

“On an International Harvester 1460 combine, the pan under the beater was hard to raise or lower because it doesn’t have any way to get ahold of it. I replaced the short bolts on the rear of the pan that must be loosened for the adjustment with 6-in. long bolts with a jam nut at the base of the bolt. Now, whenever adjustment is needed, I just loosen the jam nut and grab hold of the bolt and put the pan where it’s needed. Then retighten the jam nut and I’m done.”

From the archive · Full text
Reader shop tip

Lloyd Armstrong

Lloyd Armstrong, Sunderland, Ontario

“Here’s an idea I came up with when we needed to pour a lot of concrete in our barn and cow yard. I built a dump chute that feeds directly into our tractor-mounted 1/3-yard cement mixer. I put the correct amount of cement in with a pail and then use a skid steer to dump in one bucket full of 3/4-in.

crushed gravel. Then you just add water, mix, and drive the tractor to wherever you need to dump. The dump chute simply mounts on a frame made out of metal pipe. Makes do-it-yourself concrete work quick and easy at a price that’s about 1/3 the cost of commercial ready mix.”

Shop feature stories

From the archive · Full text
Feature story

Roll-Around Oil Changing Tank

Featured source:

Dave and Doug Miller find changing oil in cars, trucks and tractors more convenient and less messy since they made a portable oil drain tank.

The father-son team operates Miller Golden Acres near Donnybrook, North Dakota.

When they put up a new shop building recently, they installed a vehicle lift. To change oil, Doug converted an old 15-gal. water pressure tank into the oil drain tank by first cutting it open and removing the air bladder. Then he welded it back tight and added four casters to the bottom so it could be moved around easily.

On top of the tank, he cut a couple of holes - on in the center and one to the side - and welded short lengths of 1 1/2-in. steel pipe into them.

“Both pipes are threaded on the outside end so I could put valves on them,” he says.

The center pipe is the main drain and is fitted with a telescoping drain pan that he made by inserting a piece of 1 1/4-in. dia. pipe (attached to the bottom of the pan) inside a piece of 1 1/2-in. dia. tubing. He drilled a hole in the 1 1/2-in. pipe near the upper end, threaded it, and put in a bolt for a set screw so he could lock the drain pan in place.

His drain pan is made of an old disk blade. To keep oil from slopping over the edge of the disk blade, he fastened a 4-in. wide piece of rubber around the edge.

“I welded a half in. rim around the outside edge of the disk blade and pop-riveted the rubber strip to that. Then I sealed it up on the inside with silicone so oil won’t leak out,” he says.

Finally, he added a flexible hose to the bottom of the tank to drain it out and an air inlet near the top.

“I use a small amount of pressure to empty the tank into a larger used oil barrel in the shop,” he says.

“It’s easier and less messy than trying to pour oil out of one container into another.”

Contact: Farm Show Followup, Doug Miller, Miller Golden Acres, 32400 380th St. NW, Donnybrook, N. Dak. 58734 (ph 701 482-7873; E-mail: [email protected]).

From the archive · Full text
Feature story

Where To Get Hydraulic Parts, Repairs

Featured source:

If you need hydraulic components for a machine you’re building, or if you just need repair parts for an existing machine, here’s a company that specializes in everything hydraulic.

Cylinder Services in Rochester, N.Y., runs a booming mail order business and also handles repairs of hydraulic motors, cylinders, valves, and other components. Their state-of-the-art shop can handle everything from the smallest 1/2-in. dia. cylinders up to huge industrial cylinders mearsuring 24 in. in dia.

Owned by Don Welch, Scot Anderson, and Marty Lathan, Cylinder Services has been in business since 1974. The three owners get involved in every aspect of the business, maintaining a high level of quality.

The company’s mail order catalog stocks a full line of hydraulic equipment from Prince Hydraulics, an OEM supplier to many large manufacturers. Cylinder Services also carries components from other manufacturers, and offers custom services like custom machined rods, chromed rods, seal kits, and more.

They’re willing to consider any custom job. Their shop is equipped with custom-built equipment you won’t find anywhere else.

For a free copy of the Cylinder Services’ catalog, featuring hundreds of hydraulic components and more information about the company, contact: FARM SHOW Followup, Cylinder Services, Inc., 900 Maple St., Rochester, N.Y. 14611 (ph 716 328-0670).

From the archive · Full text
Feature story

Do-It-Yourself Air Filter Cleaner

Featured source:

Cleaning dirty air filters is a piece of cake at Miller’s Golden Acres, Donnybrook North Dakota, since Doug Miller made his own filter cleaner that uses a blast of air to instantly clean filters.

Miller, who farms with his father Dave, started with a small air tank that he bought at a local farm supply store.

At the farm supply store, he also picked up a 2-ft. length of 2-in. steel pipe, with threads already cut at both ends. And he bought a valve that would fit on the 2-in. pipe.

Back at the shop, he cut a hole in the bottom of the air tank and fitted it with a 1-ft. long piece of 2-in. dia. pipe. He welded the pipe into the hole.

He then cut a 15-in. circle from a piece of 1/8-in. thick sheet metal. He cut a hole in the center of that and welded in another 1-ft. long piece of 2-in. pipe.

He screwed the free ends of the two pipes into a shut-off valve.

To clean a filter, he puts about 80 lbs. of air pressure into the air tank. Then he places the filter on the shop floor or on the ground and sets the tank on top of it with the sheet metal circle over the filter.

“I just press down a little to help seal it on the filter and then open the valve,” he says.

“The big burst of air pressure cleans the dirt and debris off the filter instantly.

“Before I made this, we held the filters in our hands and tried to blow out all the dirt with a hose from the air compressor. This works much better and it takes less time, too,” he says. He figures he spent less than $100 on the filter cleaner.

Contact: Farm Show Followup, Doug Miller, Miller Golden Acres, 32400 380th St. NW, Donnybrook, N. Dak. 58734 (ph 701 482-7873; E-mail: [email protected]).

From the archive · Full text
Feature story

They Specialize In IH Manuals, Service Guides

Featured source:

A tractor and its owner’s manual are soon parted and, to the dismay of most people who restore or collect tractors, the two are seldom reunited.

If you’re looking for an owner’s manual for your IH or Farmall antique or collectible, chances are Scott and Cyndi Satterlund, Tigard, Oregon, have it.

The Satterlunds operate Binder Books, a company that specializes in original and reprint manuals for all International Harvester products. So whether you have a McCormick Deering Tractor, a Cub Cadet garden tractor or an IHC Scout, they’ve got the manual.

While his professional background is in printing, Scott’s grandfather was a Case-IH dealer. Having grown up with “red” blood, Scott began collecting IH literature as a child. This collection increased significantly in size when he bought a wealth of material from a retiring IH dealer in the late ’80s.

As a collector of IH machines (the Satterlunds own several tractors, engines, a couple of vintage Scouts and a pickup), they realized there was a market for manuals and materials. They acquired the right to reprint International books and literature and, in 1991, opened their business. It was part time at first, but in the past year, they’ve opened a store where they sell books and manuals as well as toy tractors, tin signs and other collectible items.

They’ve continually added to their offerings. They have International Harvester Co. owner’s instruction manuals, parts catalogs, service manuals and even some of the sales brochures used by dealers to sell products. They also stock manuals and parts catalogs for several other makes of farm tractors and implements, including Allis Chalmers, Ford, Case (VA Series only on hand), David Bradley, Avery, Minneapolis Moline and Oliver tractors and Page garden tractors. They don’t have all the books for these manufacturers but they’re adding more literature all the time. If the original manufacturer is still around and has a supply of the item you need, they can get it for you. Don’t hesitate to ask about manuals for products from companies that no longer exist, too, as they can usually help find them.

In addition, they have decals, seat pads, painting masks, and even canvas storm covers for Ford 8N, 2N and 9N tractors.

As a Red Power collector, Scott is always looking to add to his collection, but there’s one tractor he’d really like to find.

“It’s a wide-front end 1948 C Farmall, serial number 69578. My father bought it when he farmed near my grandfather’s dealership just outside Cumberland, Wis. I look for it whenever I’m back there, but no luck so far,” he says.

You can find a complete list of Binder Books’ products on the Internet at www.binderbooks.com. Or you can call them between 10 a.m. and 6 p.m. Pacific time. If you have manuals you’d like to sell, you can contact the Satterlunds about those, too.

Contact: FARM SHOW Followup, Binder Books, Box 230269 Tigard, Oregon 97281-0269 (ph 503 684-2024; fax 503 684-3990; Web site: www.binderbooks.com; E-mail: [email protected]).

From the archive · Full text
Feature story

Filter Systems Clean Up Shop Air

Featured source:

Welding, grinding, cleaning, cutting, painting, and just about anything else you do in your shop puts dust particles into the air that you’d probably be better off not breathing.

Wayne Hughes, owner of Air-Vac Systems, Cedar Falls, Iowa, can help keep shop air clean. For 13 years, Hughes has been making and selling air cleaners for repair and body shops, factories, restaurants, and other places of work. He recently started selling to farmers for use in farm shops.

Hughes’ air cleaners are housed in simple 16 gauge steel cabinets that measure 2 ft. square by 6 ft. long. An electric fan mounted at the center of the box pulls dirty air through filters in both ends and blows clean air out a vent at the center.

Air-Vacs use two types of filters. Air enters through a 4-in. pre-filter and continues through a bag-type filter. Because there are two sets of filters, Hughes says his air cleaner has twice the filtering capacity of most of his competitors.

Installing an Air-Vac system is simple. Hughes says the best installation is to suspend the unit by four chains from a ceiling or rafter. Or, it can be set on a shelf or bracket along the wall if that’s more convenient. Four eyebolts for hanging the unit are standard equipment.

He makes two sizes of air cleaners.

Model M-30 uses 115-volt single-phase power to operate a 3/4 hp electric motor. It has two fan speeds and can filter a maximum of 3,000 cu. ft. of air per minute. Hughes says it will easily handle air filtering needs in a 1,500 to 2,500 sq. ft. area. It weighs 175 lbs., and sells for $1,890 plus S&H.

Model M-30C is powered by a 220/440-volt 3-phase 2 hp motor. Its single speed fan processes 4,000 cu. ft. of air per minute. It will handle up to about a 3,000 sq. ft. area. While the cabinet is identical to the smaller unit, this higher capacity unit weighs 270 lbs. and sells for $2,290 plus S & H.

Air-Vacs will remove most particles from the processed air, but will not remove odors or gases that could be harmful.

Contact: FARM SHOW Followup, Air-Vac Systems, 3325 Terrace Dr., Cedar Falls, Iowa 50613 (ph 800-234-2473; fax 319 266-2524; E-mail: [email protected]).

From the archive · Full text
Feature story

Hard-To-Find Parts For Older Model Pickups

Featured source:

If you’ve got an older model pickup that you still use or would like to restore, here are several companies that specialize in replacement parts. Many older parts are no longer available from the original manufacturers so some of these companies make their own parts - often with better specs than the originals. All the companies listed below have catalogs of available parts.

Obsolete Chevrolet Parts Co. P.;O. Box 68 Nashville, Ga. 31639 ph 800 248-8785 Website: www.obschevy.com Specializes primarily in Chevy trucks 1929 to 1972, but has parts for some newer models as well. Three catalogs available for $3.00 apiece: 1929-59; 1960-72; and 1973 and up. Catalogs available on-line at no charge.

LMC Truck Parts P.O. Box 14991 Lenexa, Kan. 66285 ph 800 222-5664 All Chevrolet trucks 1947 to 1987. Three catalogs available at no charge: 1947-1959; 1960-1972; and 1973-1987.

Cheyenne Pickup Parts Box 959 Noble, Okla. 73068 ph 405 872-3399 Website: www.cheyennepickup.com Parts and accessories for full-size Chevy pickups from 1960-1987 and full-size Chevy Blazers and Suburbans from 1969-1991. Catalog $4.00.

KC Obsolete Parts Inc. 3343 N. 61 Kansas City, Kan. 66104 ph 913 334-9479 Specializes in Ford truck parts 1948 to 1972. Catalog $2.00.

Dodge Connection P.O. Box 149 Moorefield, W. Va. 26836 ph 304-538-2666 Website: www.dodgeconnection.com Specializing in 1972-1980 Dodge truck parts. Free catalog.

American Classic Truck Parts P.O. Box 409 Aubrey, Texas 76227 ph 940 365-9786 Website: www.americanclassic.com Parts for 1936 to 1972 Chevy and GMC pickups.

Dennis Carpenter P.O. Box 26398 Charlotte, N.C. 28221 ph 704 786-8139 Website: www.dennis-carpenter.com Ford pickups 1932 to 1986, 1966 to 1979 Broncos, and 1961 to 1967 Econoline vans. Also Ford cars and tractors. Full range of catalogs available.

LeBaron Bonney Co. P.O. Box 6 Amesbury, Mass. 01913 ph 800 221-5408 Website: www.lebaronbonney.com Upholstery and supplies for 1928 to 1954 Ford and Chevy pickups. Free catalog.

Steel Rubber 6180 Highway 150 East Denver, N.C. 28037 ph 800 544-8665 Website: www.steelerubber.com GM trucks.

Obsolete Ford Parts Company P.O. Box 787 Nashville, Ga. 311639 ph 912 686-2470 Website: www.obsoleteford.com Ford pickups 1948 to 1979 and 1966 to 1977 Broncos.

From the archive · Full text
Feature story

Grain Bin Converted To Farm Shop

Featured source:

An Iowa farmer put an abandoned grain bin back into productive use by converting it into a farm shop and storage area.

Jim Spaid started with a 3,000-bu. bin. A section of railroad track supports an overhead hoist. A stairway that runs to an upper level storage area is pulled down as needed by a rope. An underground line brings compressed air from another building to the grain bin shop.

He cut a large door into one side and hung lots of storage hooks around the outside walls.

Contact: FARM SHOW Followup, Jim Spaid, 16141 290 St., Radcliffe, Iowa 50230 (ph 515 864-2431).

From the archive · Full text
Feature story

No-Mess “Barrel Buddy” Drains Used Oil Fast

Featured source:

Anyone who has tried to pour used oil into a barrel using an ordinary funnel knows that it’s a slow and messy process. You pour a little oil into the funnel and then wait to let it drain, then have to repeat the process several times.

Randy Duden, Gifford, Ill., came up with a solution. He made a large capacity, square steel box with a screen on top and a 1-in. drain at the bottom, which is flat. The box is designed to mount on top of any 30 or 50-gal. drum. Duden simply places used oil filters, or an upside-down bucket, etc., on top of the screen and lets the oil drain into the barrel.

“It allows me to drain oil into the drum quickly and without making a mess. It also makes it easy to flush all the oil out of filters,” says Duden.

“The box is made from 12-ga. steel and holds about four gallons. The screen catches any drain plugs or other foreign objects.”

The “Barrel Buddy” is now on the market. Sells for under $70 plus S&H.

Contact: FARM SHOW Followup, The Spreader, Inc., Hwy. 136, Box 189, Gifford, Ill. 61847 (ph 800 428-9046 or 217 568-7219; fax 7619).

From the archive · Full text
Feature story

Convert Older GM Vehicles To Electronic Ignition

Featured source:

It’s easy to change an older model GM vehicle (pre 1973) to electronic ignition, eliminating the need to change points and rotor, says Pete Peters, Osler, Sask.

“Once you convert to electronic, they start and run better,” says Peters, who made the conversion on a 1969 Chevy half-ton with a 350 engine.

“I was tired of replacing points and looked into making a conversion. I discovered it was easy to do.”

First, remove the old distributor and coil and then replace them with an electronic distributor from a 1974 or newer vehicle. Electronic distributors have the coil mounted on the distributor cap. Run a 12-ga. wire from the distributor to a fuse box terminal, which is live only when the ignition switch is turned on.

Adjust the spark plug gap to .045, remove the old spark plug wires and replace them with new high-energy wires. You’ll also have to readjust the timing.

“This change will work on any older car, half-ton, or grain truck with a 305 or 350 engine,” says Peters.

Contact: FARM SHOW Followup, Pete Peters, Box 166, Osler, Sask. S0K 3A0 Canada (ph 306 239-2045).