Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 20, No. 6 (1996)

Vol. 20, No. 6 (1996)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 30–32

62 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip 1 of 2

John Hoegl

Individual tip 1 of 2 from this reader’s published contribution.
John Hoegl, Lloydminster, Sask.

“We installed a hand-operated winch on the left side of our two Deere 8820 combines so we can raise or lower the straw chopper by simply turning a crank. We lower the chopper whenever we want to drop the straw into a windrow for baling. A cable runs from the winch up over a pulley mounted on top of the combine and down to the chopper drum. We cut a hole on top of the combine to make room for the cable. We also made this modification to our Deere 7720.

From the archive · Full text
Reader shop tip 2 of 2

John Hoegl

Individual tip 2 of 2 from this reader’s published contribution.
John Hoegl, Lloydminster, Sask.

“When using our Deere 535 auto-wrap round baler we had a problem getting enough twine wraps on the left side of the bale, especially when we had to bale dry straw. It would compress, allowing the twine to slide off the bale. We solved the problem by converting the baler’s automatic cut-off control to a manual twine knife control that lets us wrap twine around the bale as many times as we want. We bolted a chain link onto the end of the twine arm and tied a rope to the link that leads up to the tractor cab. We also turned the plate that engages the knife sideways so that the knife can’t cut twine until the operator pulls on the rope. It lets us reduce the number of wraps across the center of the bale and wrap extra twine on one end. It works great and also reduces the amount of twine normally needed by about one third.”

From the archive · Full text
Reader shop tip 1 of 2

Tim Beirnes

Individual tip 1 of 2 from this reader’s published contribution.
Tim Beirnes, Cambridge, Ontario

“The wagon hitch on my Massey-Ferguson 124 baler was built too light and often broke. The hitch was made up of a 2-in. dia. steel pipe that slid inside a 2 1/4-in. (inside dia.) light wall sleeve and was pinned to it. I threw the sleeve away and replaced it with a cold-rolled 2 1/2-in. sq., 1/4-in. wall tube which solved the problem. I drilled a hole in the sq. tube to match. I made this conversion on three different Massey-Ferguson balers.

From the archive · Full text
Reader shop tip 2 of 2

Tim Beirnes

Individual tip 2 of 2 from this reader’s published contribution.
Tim Beirnes, Cambridge, Ontario

“We broke a knuckle on the baler’s pto shaft on a Saturday night. A new yoke would have cost about $100 and my dealer was closed for business on Sunday. I solved the problem by borrowing the pto shaft off an old manure spreader. I shortened the shaft to the right length. Then I cut off the machined part of the knuckle on the baler pto shaft and welded it to the heavier knuckle on the spreader shaft. Eight years and 30,000 bales a year later it still works beautifully.”

From the archive · Full text
Reader shop tip

Bruce Gamble

Bruce Gamble, La Feria, Texas

“I’ve found a relatively inexpensive way to re-pair worn knuckle joints on any Deere MFWD tractor. The problem is, the seals on the double U-joints that couple the two parts of the axle together cut grooves in the yokes as they wear. Replacing the yokes is neither an easy nor cheap chore. I take the knuckle joint and turn the yoke down in my lathe. I then install a stainless steel bushing I make out of pipe to bring the yoke back to correct size. This repair will work on any Deere tractor with MFWD. Cost is $150 per side, compared with anywhere from $300 to $1,200 per side to replace them depending on the model of tractor.”

From the archive · Full text
Reader shop tip

Roger Baldwin

Roger Baldwin, Rock Rapids, Iowa

Back in the early 1960’s, before the advent of portable AC welders, Roger built a DC welder from a 32-volt generator out of a surplus WW II airplane.

“I ordered one from a surplus depot after seeing an ad in a magazine about making such a welder,” says the retired Lyon County extension agent.

“The generator had a short shaft with a spline on one end. I found a driveshaft with spline that matched it at an auto junk yard. I shortened that shaft and welded a knuckle onto it so it would match the pto shaft on our early 1940’s Allis Chalmers B. I wired welding cables into the outlets where the generator’s wires had been. I mounted the welder on a two-wheel trailer I pulled behind the tractor to keep the two shafts from vibrating apart. Then I just started the tractor and instantly had a welder. It worked beautifully.”

From the archive · Full text
Reader shop tip

James C. Perley

James C. Perley, Little Sioux, Iowa

“To unstuck pistons on an IH tractor, we put a chain around the engine, poured oil in the cylinders and put a round, wood block in one cylinder. Using the chain as a brace, we used a jack to push the wood against the piston until it came loose.”

From the archive · Full text
Reader shop tip

Dale E. Nielson

Dale E. Nielson, Chapman, Neb.

“We’ve had good luck using a new-style plastic welder to repair cracks in plastic irrigation pipe. Seems to work well.” (Fouillard Farm Supplies Ltd., Box 524, White City, Sask., Canada S0G 5B0)

From the archive · Full text
Reader shop tip 1 of 3

Chris Palmer

Individual tip 1 of 3 from this reader’s published contribution.
Chris Palmer, Enumclaw, Wash.

“I couldn’t unbolt a tie rod off the steering arm on my Massey 65. My 3/4-in. Craftsman expandable wrench broke but my Stanley Proto wrench took it off with a 3-ft. piece of pipe on it. The Proto is expensive ($300 for a 12-piece set) but if it won’t break in the field, it’s worth it.

From the archive · Full text
Reader shop tip 2 of 3

Chris Palmer

Individual tip 2 of 3 from this reader’s published contribution.
Chris Palmer, Enumclaw, Wash.

“My best maintenance tip is to clean, clean, clean. If you keep your equipment clean, problems will show up easier - like oil leaks, cracks, and so on.

From the archive · Full text
Reader shop tip 3 of 3

Chris Palmer

Individual tip 3 of 3 from this reader’s published contribution.
Chris Palmer, Enumclaw, Wash.

“One of our handiest shop tools is an old bearing press we bought for $10. It helps push all kinds of bushings, bearings and bolts in and out.”

From the archive · Full text
Reader shop tip

Allen Reimer

Allen Reimer, Capron, Ill.

“We had a problem. Our cattle needed more vitamins. We mounted an insecticide-type Gandy attachment on the elevator that runs from the silo to the belt feeder. As the elevator runs, vitamins are dropped on the silage. We simply ran a chain from the elevator drive to the Gandy unit. Works great.”

From the archive · Full text
Reader shop tip 1 of 2

Andy R. Hodges

Individual tip 1 of 2 from this reader’s published contribution.
Andy R. Hodges, Galax, Va.

“One tough maintenance job I’ve got is putting bearings on the rollers of a New Holland Haybine. It’s extremely tough and time-consuming. I made it easier by using a torch to cut the old bearings off the shaft.

From the archive · Full text
Reader shop tip 2 of 2

Andy R. Hodges

Individual tip 2 of 2 from this reader’s published contribution.
Andy R. Hodges, Galax, Va.

“The electric power window on my 1985 Ford LTD would not work. A new motor would have cost $85. When I took the panel off the door I found that the plastic rollers were broken. I installed four steel balls in place of the plastic and the window works now. I saved the $85.”

From the archive · Full text
Reader shop tip

John Cernius

John Cernius, Climax, Mich.

“I break beads on tractor tires by using down pressure from my backhoe stabilizer arm. The bucket is positioned to hold the wheel flat on the ground and the stabilizer is used to unseat the bead. It’s safe and quick.”

From the archive · Full text
Reader shop tip 1 of 2

Tom Graham

Individual tip 1 of 2 from this reader’s published contribution.
Tom Graham, Henderson, Minn.

“Instead of removing the straw chopper on Massey Ferguson 300, 410 and 510 combines when switching from corn to beans, I remove the front two bolts and hinge the chopper down on the back two bolts, then put a brace made of flat or angle iron between the mounting holes on the combine chopper.

From the archive · Full text
Reader shop tip 2 of 2

Tom Graham

Individual tip 2 of 2 from this reader’s published contribution.
Tom Graham, Henderson, Minn.

“I’ve discovered that auto salvage yards that wreck late model cars have used anti-freeze available. I bought a 55-gal. drum for $25 and use it in all my older cars, truck and farm machinery. Works as good as new.”

From the archive · Full text
Reader shop tip 1 of 2

Don Booth

Individual tip 1 of 2 from this reader’s published contribution.
Don Booth, Leoville, Sask.

“I had a problem with erratic operation of the Powershift on my 1986 Case-IH 4494 tractor. The dealer couldn’t fix it and the company service rep was no help either. I finally found the problem myself - bad electrical connections. One thing that helped is that I always buy service manuals for my tractors. They save time and more than a few trips to the dealer. Electrical wiring diagrams are especially helpful.

From the archive · Full text
Reader shop tip 2 of 2

Don Booth

Individual tip 2 of 2 from this reader’s published contribution.
Don Booth, Leoville, Sask.

“My shop makes repair work easier. It’s fitted with lots of plug-ins, a large engine hoist, a 5-ton floor jack, a hydraulic press, welders, and it’s heated for winter work.”

From the archive · Full text
Reader shop tip 1 of 2

Marshall Forren

Individual tip 1 of 2 from this reader’s published contribution.
Marshall Forren, Marshall, Ill.

“I store nails, screws, nuts and bolts in coffee cans with plastic lids. I write on top what’s inside. The lids keep moisture out and the writing makes it easy to know what’s inside.

From the archive · Full text
Reader shop tip 2 of 2

Marshall Forren

Individual tip 2 of 2 from this reader’s published contribution.
Marshall Forren, Marshall, Ill.

“To save money, I use the best sickle sec-tions out of old sickles to replace broken ones in the new sickle on my mower.”

From the archive · Full text
Reader shop tip 1 of 2

David M. Munson, Jr.

Individual tip 1 of 2 from this reader’s published contribution.
David M. Munson, Jr., Paris, Tex.

“I put a grease pit in my shop that works great and saves time. The shop also has 18 ft. of clearance and has four doors. The smallest door is 14 ft. wide and the largest is 28 ft. wide.

From the archive · Full text
Reader shop tip 1 of 2

Lanny Hecker

Individual tip 1 of 2 from this reader’s published contribution.
Lanny Hecker, Faucett, Mo.

“We put two pits in the floor of our shop to make it easier to service the bottom of vehicles. Much easier than jacking them up and using a creeper.

From the archive · Full text
Reader shop tip 2 of 2

Lanny Hecker

Individual tip 2 of 2 from this reader’s published contribution.
Lanny Hecker, Faucett, Mo.

“I came up with a handy device to check brake lights on cars and trucks when working alone. I welded a rod with a disk blade spacer on it for weight to a pair of vice grips. When I clamp it to the brake pedal it’s heavy enough to hold it down.”

From the archive · Full text
Reader shop tip 1 of 2

Paul Dean

Individual tip 1 of 2 from this reader’s published contribution.
Paul Dean, Bolton, Ontario

“When welding inside buildings, heat and fumes can be easy to remove from the welding area by installing an old furnace fan and venting it to the outside of the building. Easy to do and cheap.

From the archive · Full text
Reader shop tip 2 of 2

Paul Dean

Individual tip 2 of 2 from this reader’s published contribution.
Paul Dean, Bolton, Ontario

“The sweep assemblies on my IH vibra-shank chisel plow have a habit of breaking. To repair damaged units and strengthen others, I’ve found that welding a bead around the end of each assembly will solve the problem.

From the archive · Full text
Reader shop tip

Mark Busscher

Mark Busscher, Zeeland, Mich.

“After reading in FARM SHOW about a farmer’s overhead hoist, I copied the idea in my shop. I put two chain hoists on rollers. The first mounts on a 54-ft. I-beam and the other’s on a 12-ft. I-beam that pivots across the shop. Very handy.”

From the archive · Full text
Reader shop tip

Bayard E. Young

Bayard E. Young, Elkwood, Va.

“This is a simple idea but it works well. I use wide mouth plastic peanut butter jars to hold nuts, bolts and miscellaneous parts. You can see what’s inside and unlike glass jars, they won’t break if you drop them.”

From the archive · Full text
Reader shop tip

Ruth & Sylvester Riehle

Ruth & Sylvester Riehle, Sunman, Ind.

“Parts and repairs for older Massey Ferguson combines are costly and time consuming. We have bought several used junk combines at auctions and now have many replacement gears and bearings and belts readily available.”

From the archive · Full text
Reader shop tip

Kenneth Roberts

Kenneth Roberts, Quanah, Texas

“Changing the last stage fuel filter on my 930 Case diesel tractor is difficult, as is checking and filling the power steering reservoir. I solved the problem by cutting a door in the hood, with hinges and a latch.”

From the archive · Full text
Reader shop tip 1 of 2

Mark E. Hansen

Individual tip 1 of 2 from this reader’s published contribution.
Mark E. Hansen, Sherman, Ill.

“I cut the bottoms off detergent bottles and turn them upside down to use as funnels with handles. Helps when adding hydraulic fluid to my Deere 2740 tractor.

From the archive · Full text
Reader shop tip 2 of 2

Mark E. Hansen

Individual tip 2 of 2 from this reader’s published contribution.
Mark E. Hansen, Sherman, Ill.

“The wood decks on hay wagons wears out rapidly. I replaced mine with 1 1/4-in. thick treated deck wood that’s strong and should last over 20 years. It’s cheap in the long run because of the longer wear.”

From the archive · Full text
Reader shop tip

Matt Biggs

Matt Biggs, Chesterton, Ind.

“I made a handy bead breaker for all types of farm tires by welding a 15-in. curved chisel plow point to a used hydraulic cylinder. Then I mounted an air chuck in the end of the hydraulic cylinder so I can use air pressure to break beads. The tool mounts on the wall of my shed. It works great.”

From the archive · Full text
Reader shop tip

Donald L. Stobaugh

Donald L. Stobaugh, Jennings, Ohio

“The stabilizer bars on my Ford 8N, 800, and 3000 tractors fasten under the rear axle. The problem is that regardless of the type of pin used to secure them, they catch on brush or weeds and get lost. Then the bar drops off, sticks in the ground, bends, or gets caught under your implement. I solved the problem by using a medium-sized padlock. Since I started doing this I haven’t lost another stabilizer bar. I keep the key on a ring on the tractor.”

From the archive · Full text
Reader shop tip

Richard Bowman

Richard Bowman, Chambersburg, Penn.

“I used Pyro-Putty to fill a long 3/ 8-in. wide crack in the exhaust manifold on an old 855 Hercules engine. I think the re-pair is now stronger than the rest of the manifold. The putty stays in there even when the engine backfires. It’s easy to use. You just work it into the crack and let the heat of the engine cure it. Works on headers, manifolds, mufflers, catalytic converts, and more.” Contact: Aremco Products, Inc., P.O. Box 429, Ossinging, N.Y. 10562 (ph 914 762-0685).

From the archive · Full text
Reader shop tip

O.J. Thompson

O.J. Thompson, Grand Junction, Iowa

“I’ve had trouble with my pressure water system in that it waterlogs. My plumber inserted a rubber bladder in the pressure tank but it burst and got into the water lines and I had to dig up the lines. Since then I have repeatedly had to drain the tank and use compressed air for pressure. I’ve thought of putting an insulated tank up on stilts or maybe a float device in the tank to fill it to the correct level. Any solutions out there?” (ph 515 738-2525).

From the archive · Full text
Reader shop tip 1 of 2

William C. Reeks

Individual tip 1 of 2 from this reader’s published contribution.
William C. Reeks, Cromwell, Kent.

“Here are two grease gun ideas that work for me. I wire a small plastic pill bottle to the handle of my gun where I can slip the nozzle of the gun when not in use. Keeps the tip clean.

From the archive · Full text
Reader shop tip 2 of 2

William C. Reeks

Individual tip 2 of 2 from this reader’s published contribution.
William C. Reeks, Cromwell, Kent.

The other idea is the way I converted a hand grease gun to a foot-pumped grease gun. I added extra hose to the gun, mounted it on a board with U-bolts, and made a toe stirrup out of heavy wire to mount on the handle.”

From the archive · Full text
Reader shop tip

J.S. Adams

J.S. Adams, Cross Plains, Texas

“To protect air valves on impact tools from dirt, I use plastic hydraulic valve covers. Saves many hours of cleaning out dirt and prevents damage.”

From the archive · Full text
Reader shop tip

Kenneth Koenen

Kenneth Koenen, Burlington, Wis.

“The rear teeth on our Brillion Culti-Mulcher always acted like a rake, plugging up with residue. To solve the problem, we mounted Danish tines on the rear bar. They do the job yet let trash flow through. That’s the only modification but it worked.”

From the archive · Full text
Reader shop tip

Klaus Nielsen

Klaus Nielsen, Dunwoody, Ga.

The trickiest part of trying to sharpen a metal drill bit is trying to get the 118-degree tip angle so the drill will run true. Klaus re-cently pointed out in an article in Woodshop News that you can vary the angle slightly to 120 degrees by using two standard machine nuts as a guide. Just grind the tip down to fit the angle of the two nuts and it’ll work fine, he notes.

From the archive · Full text
Reader shop tip

Wayne Bates

Wayne Bates, Emmet, Neb.

“Here’s a handy shop tool I put together years ago. I mounted an older style post vise (the type many shop men now call obsolete because they prefer swivel-type bench vises) on a fairly heavy engine flywheel. I can roll this around anywhere in my shop. I mainly use it to hold things when welding.”

From the archive · Full text
Reader shop tip

Ronald H. McConnell

Ronald H. McConnell, Brookville, Penn.

He saves money by making many of his own replacement parts.

“Years ago I set up a complete machine shop and taught myself to use the machine tools. It’s amazing how cheaply a part can be fabricated compared to what dealers charge. My other shop advice is to use lots of air-powered tools and get a big MIG welder. They make all repairs quicker and easier.”

From the archive · Full text
Reader shop tip

Joe Thomas

Joe Thomas, Mattson, Miss.

“When we bent a driveshaft on a mower-condi-tioner, we decided to repair it rather than replace it. The shaft is hollow. We cut out the bent part and found a pipe in our scrap pile that just fit over the outside of the shaft. We then drove the two cut shafts inside the pipe and spot welded the shaft to the pipe. It works as good as new now.”

From the archive · Full text
Reader shop tip

Jack Griffith

Jack Griffith, Arlington, Texas

“When I got a welder, I knew I would need a heavy- duty extension cord to power it. I bought a 100 ft. roll of 3-wire cable and plugs for each end. We just figured what size wire we would need for a 200 amp welder. It’s real stiff and I knew it would be difficult to roll it up for storage so I bought a water hose storage reel (for $16) on wheels. Now it’s simple to pull out the cable and wind it back up.”

From the archive · Full text
Reader shop tip

Arnold C. Weber

Arnold C. Weber, Frankenmuth, Mich.

“I’m sending along photos of a bead breaker I made for tractor tires. I always had trouble getting tires off but this little tool gets the job done. It’s completely adjustable for different size tires. It’s made from one piece of channel iron that lies face down as a base and two smaller pieces of channel that act as uprights. A cross bar pins to holes drilled in the two uprights. There’s a curved push plate on one end and a hand-pumped 10-ton hydraulic jack on the other end. Raising or lowering the cross bar makes it easy to adapt to different size tires.”

From the archive · Full text
Reader shop tip 1 of 2

Gregory Peltier

Individual tip 1 of 2 from this reader’s published contribution.
Gregory Peltier, Danbury, Texas

“One day I was greasing my 1460 International combine and had to climb almost all the way up the combine tire to grease four hard-to-reach zerks. I slipped and fell hard onto the ground. That got me thinking there had to be a better way. I made grease hoses out of 1/8-in. dia. hydraulic line and plumbed them in place of the original zerks by drilling and tapping the holes. I clamped the zerks to the other end of the hose and attached the hose to the side of the combine with conduit clamps. Works great.

From the archive · Full text
Reader shop tip 2 of 2

Gregory Peltier

Individual tip 2 of 2 from this reader’s published contribution.
Gregory Peltier, Danbury, Texas

“Another problem on the combine was tightening the reel chain. I welded a big nut to the reel motor bracket and to the side of the combine. Then I put a long bolt through both nuts. To tighten the chain I just tighten the bolt. I welded a small nut on the side of the motor mount to insert a set screw to hold the bracket in place once it’s tightened.”

From the archive · Full text
Reader shop tip

Darl Blackman

Darl Blackman, Bloomingdale, Mich.

“When the power steering pump on our Massey Ferguson 175 tractor went out, I found out a new one would cost $348. I saved the money by putting a GM automotive power steering pump on it. My only cost was $20 for a pulley and belt to run the pump off the alternator. Worked very well.”

From the archive · Full text
Reader shop tip 1 of 2

James S. Wilson

Individual tip 1 of 2 from this reader’s published contribution.
James S. Wilson, Celeste, Tex.

“Here’s how I made a 360° swivel mount for my bench vise. I bolted a 3/8-in. thick piece of steel plate to the bottom of the vise and then welded a short length of pipe to the center of the base. Then I cut a 1/4-in. slot out of a slightly larger piece of pipe, welded two tabs to it, and mounted it on the side of the work bench. Vise turns 360° inside the slotted pipe, which can be quickly tightened down at any point. Great for welding jobs.

From the archive · Full text
Reader shop tip 2 of 2

James S. Wilson

Individual tip 2 of 2 from this reader’s published contribution.
James S. Wilson, Celeste, Tex.

“I was installing wire leads to an arc welder and didn’t have any terminals on hand. Instead, I found some copper pipe about the diameter of the wire and cut off two pieces about 2 1/2 in. long. I flatened half of each piece and drilled a hole through the ends to bolt to the welder. I slipped the wire into the open end and soldered it in place. Worked just fine.”

From the archive · Full text
Reader shop tip

Dale L. Williams

Dale L. Williams, Maple, Wis.

“We mounted low-cost duals on our 1992 New Holland 855 baler. It makes heavier, 1,800-lb. bales than the early New Holland 850 we had before so it had more of a tendency to bog down in wet fields. We’d seen duals used on balers before so we decided to see what we could come up with on our own.

“We discovered that the 13-in. wheel rims off an old Escort car fit perfectly inside the baler rims so we used them for spacers. We used 1-ft. threaded rods for the long bolts to attach the car rims to the baler’s. We then fitted the rims with tires off one of our hay wagons. They’re only 1/2-in. shorter in height than the baler’s tires so they’re ideal for adding flotation on wet ground. Plus, we’ve found they add stability to the baler, which is rather narrow and squat, on dry ground. We put the duals on three years ago and haven’t taken them off since. By this time, many of our neighbors are running duals on their balers, too.”

Shop feature stories

From the archive · Full text
Feature story

Modified 6-Cylinder Engine Uses 3 Cylinders To Compress Air

Featured source:

If you’ve ever thought of turning an old engine into a high-volume air compressor, you’ll be interested in the way Clayton, Ill., farmer David Buss modified a 1961 Ford car engine to compress air. Buss left three of the cylinders intact so they run normally, but then modified the other three cylinders to compress air. He first blocked off the intake manifold on the compressor end of the engine so it wouldn’t draw in gas. He next removed a frost plug from the compressor end to let in air. He installed an air cleaner off an old lawnmower in the frost plug port. He replaced the spark plugs on the “compressor cylinders” with commercial check valves to keep pressure from backfeeding into the cylinders. The engine starts and runs normally on the three remaining unmodified cylinders,” Buss says.

“It develops up to 170 psi’s, more than enough power to operate air tools. It really works well.”

He mounted the air compressor on a home-built 5 by 7-ft. trailer that’s also fitted with a Lincoln welder and an acetylene torch. Total cost of the project was $700, including $27 apiece for the check valves. Contact: FARM SHOW Followup, David Buss, R.R. 2, Box 27, Clayton, Ill. 62324 (ph 217 894-6417 or 7070).

From the archive · Full text
Feature story

Urethane Sprockets For Rock Pickers & More

Featured source:

“Conventional steel sprockets last maybe 400 hours. Our polyurethane sprockets are proven to last easily twice as long,” says Dick Sydor, a sales representative for PCO, a Marshfield, Wis., manufacturer.

“Another advantage is they’ll increase life of belted chains on the equipment. ‘Our new Harvesthane urethane sprockets are made for rock pickers as well as sugar beet, potato, carrot and onion harvesters.”

They’re available in a wide variety of sizes and are competitively priced from $40 to $80 apiece for most standard sizes.

Contact: FARM SHOW Followup, Dick Sydor, PCO, 2515 West Arnold, Marshfield, Wis. 54449 (ph 715 387-6303, ext. 22; fax 389-1926).

From the archive · Full text
Feature story

Portable Bead Breaker

Featured source:

This portable bead breaker uses hydraulic jack pressure to press the tire off the bead lip.

“It easily handles even the toughest tires,” says inventor Bob Sagen, noting that it’ll work on anything from car to tractor tires.

The “Bead Jacker” has a pair of jaws that go between the tire and rim, and a lock-down handle equipped with a plunger. Pushing the handle back forces the plunger against the rim which in turn forces the jaws under the rim. Once the handle is pushed all the way down it overcenters to lock the plunger in place so it can’t come off.

“The jack is at a right angle to the work area so the tire is pushed exactly straight down with the jack,” says Sagen.

“The plunger is equipped with an adjustable bolt for adapting the unit to different size wheels.”

Comes with an 8-in., 2-ton hydraulic jack. Sells for $159.95.

Contact: FARM SHOW Followup, Pro-Chassis, Inc., County Road 34 East, Box 211, Arthur, N. Dak. 58006 (ph 701 967-8386).

From the archive · Full text
Feature story

New Machine Flushes Sludge From Engines

Featured source:

When you change the dirty oil in your tractor or combine’s engine, you probably think the job is done.

Not Kevin Lea of Lubbock, Texas. He’s come up with a new, self-contained “engine flusher” that’s designed to be used after dirty oil is removed but before new oil is added. Called “Tractor Flush”, the just-introduced machine uses air pressure to inject a cleaning solution into the engine to remove sludge that coats the inside even after dirty oil is removed. The machine can also be used to clean transmissions and hydraulic systems.

“It can add years to the life of an engine or transmission,” says Lea, who showed his innovative new system to the public for the first time at the recent Texas Farmer-Stockman show near Lubbock.

“It removes over 84% of wear metals and other harmful contaminants that a normal oil change misses and keeps it from being recirculated throughout the engine after new oil is added. It’s designed mainly for preventative maintenance and will reduce the need for overhauls. However, if an overhaul is necessary the job will be much easier if you flush the engine out first.

“Sludge can form inside an engine no matter how new it is or often you change the oil. Removing it reduces the engine’s operating temperature and increases oil pressure, resulting in increased horsepower and improved fuel efficiency.”

The “Tractor Flush” unit is equipped with hose adapters that attach to the vehicle’s oil filter port and also to the oil drain hole. It’s equipped with controls for a variety of pressure settings and for various soaking- circulating cycles. The cleaning solution is continuously filtered. Dirty solution goes directly into the waste oil for recycling.

Lea says he plans to sell the machine for about $10,000.

“If you have three or more tractors it’ll pay for itself in extended tractor life. Several farmers could buy a unit together, or you could earn extra income off the farm by offering it as a service. It’s light enough that two people can put it in the back of a pickup.”

Contact: FARM SHOW Followup, Kevin Lea, 4200 Boston, Suite 19, Lubbock, texas 79413 (ph 806 797-0177).

From the archive · Full text
Feature story

Bumper-Mounted “Step” Makes Truck Service Easier

Featured source:

“I built it to slip over the front bumper on my Dodge 3-ton grain truck to make it easier to service the engine,” says Michel Dufault, Haywood, Manitoba, about the 5-ft. long, 1-ft. wide service step he made by bolting two 2 by 6 planks to metal clamps that simply slip over the bumper.

“I built it because the front bumper on my truck is only 2 1/4 in. wide and is often slippery,” says Dufault.

“It eliminates the need to use a step ladder or a bench and is wide enough that I can lay tools and other items on it while I work on the engine.”

Contact: FARM SHOW Followup, Michel Dufault, Box 67, Haywood, Manitoba, Canada R0G 0W0 (ph 204 379-2426).

From the archive · Full text
Feature story

Remote Battery Disconnect Safety Switch

Featured source:

You’ll never have to worry about draining power out of your batteries when machinery’s not in use, thanks to this new remote battery disconnect safety switch. The device, from Gizmos & Gadgets Inc., consists of a knife blade-type switch that disconnects power when you flip it up. It installs in minutes in any remote location, simply by running a cable to it from your battery.

Great for working on equipment without having to disconnect the battery and helps discourage theft or unauthorized use, the company adds. Sells for $24.95 plus $3.95 S&H. A top post-mounted battery switch is also available for the same price. Contact: FARM SHOW Followup, Gizmos & Gadgets Inc., 6519 Cecilia Circle, Minneapolis, Minn. 55439 (ph 800 215-

From the archive · Full text
Feature story

Add New Life To Deere Chisel Plows

Featured source:

If you’ve ever had problems with inaccu-rate depth control on your Deere chisel plow that was caused by failure of the walking beam axles, you’ll be interested in this new update kit offered by Dave Barnes of Barnes Welding, Inc., Waterville, Wash.

The kit includes a main pivot spindle, heavy duty Timken tapered roller bearing and bearing housing, and heavy duty rectangular steel tubing. You cut the original pivot spindle off the implement’s lift arm and weld the new one on in its place, then attach the steel tubing to the original wheel spindles and hubs.

“It makes your Deere chisel plow work better than new because you’re putting on a stronger spindle and using a stronger, frictionless, sealed bearing that’s packed in grease for long life. Also, maintenance is easier because no greasing is necessary,” says Barnes.

“The problem with Deere chisel plows and field cultivators is that the walking beam axle is built from 4 by 2 rectangular steel tubing that isn’t strong enough to carry the weight of the implement. Our updated walking beam axles are built from 6 by 2 tubing and use heavy duty bearings so they’ll outlast the implement.

“Another problem is that the original walking beam pivot is made with a brass bushing that should be greased daily. Dust can enter the bushing because there are no seals, which causes the bearing to wear out prematurely. The first sign of trouble is a gradual leaning of the wheels which can exert excessive wear and pressure on the sides of the tires so that they don’t follow each other. This allows the walking beam to wander left and right, compound-ing the existing wear many times over. Also, the main spindle will eventually wear through the metal housing that holds the bearing. This can lock up the walking beam and keep it from following the ground contour which results in the depth control problems.”

The kits sell for $375 apiece. One kit is required per lift arm.

Contact: FARM SHOW Followup, Dave Barnes, Barnes Welding, Inc., Box 614, Waterville, Wash. 98858 (ph 509 745-8588).