Handy “4-In-1 Tool” Built For New Holland Haybine
Edward Fett, Lennox, S. Dak., says the “4-in-1” tool he made for his New Holland 499 swing tongue haybine saves him a lot of time and trouble.
Read the complete story →717 shop tips and stories · page 4 of 12, newest issues first.
Edward Fett, Lennox, S. Dak., says the “4-in-1” tool he made for his New Holland 499 swing tongue haybine saves him a lot of time and trouble.
Read the complete story →Gary Houdek can push his propane/oxy torch kit around the shop floor or tow it to the field behind an ATV. Equipped with car wheels, the cart is just as stable either way, and adding the tongue for…
Read the complete story →Anyone who does a lot of maintenance work on cars and trucks in their shop will like this new QuickJack portable car lift that eliminates the need for conventional jacks and stands. The electric-hydraulic lift raises and lowers…
Read the complete story →“I use inexpensive dog collars purchased from our local Dollar Store to hold cords, tow straps, and cargo ratchet wraps together for tidy storage. You can buy different size collars and adjust them to fit. The collars come…
Read the complete tip →“Another solution for small strap storage is to place a wrapped-up strap inside an old sock. I store several straps together this way inside a duffel bag so all my straps are in one place when I need…
Read the complete tip →“By mounting the stator from a discarded permanent magnet motor onto a wooden plate, I can use it to store small magnetic parts such as drill bits or even sewing pins and needles. I remove the stators from…
Read the complete tip →Mike Becker has no problem parting with his collection of manuals, brochures and ag equipment memorabilia. He says it helps that he is a “paper farmer”, not a collector.
Read the complete story →This portable work table quickly folds out like a pop-up tent to provide a 4 by 8-ft. work surface.
Read the complete story →“Our new sealed bearing rebuild service for Deere planters improves the performance of old and worn parallel linkage arms. We replace the original bushings with sealed bearings that never need grease. The rebuilt arms work smooth and stay…
Read the complete story →“I made a caddy to store and transport planer blades. It’s a long rectangular wood box with 3 slots that keep the blades separate. A hanger goes through holes in brackets at the top of the holder so…
Read the complete tip →“Having a small shop, I don’t have a lot of room to attach tools to the floor – such as my metal bender, tire changer, vise, etc. So I put a pocket in the floor to accept posts…
Read the complete tip →Minnesota handyman Mark Rinke bought a used Land Pride 4211 batwing mower that had issues with the gauge wheels, the wings, and the pto shaft and hitch. After he made improvements to all those components, the mower is…
Read the complete story →“My 10-year-old Work Sharp knife sharpener does an excellent job (www.worksharptools.com; ph 800 597-6170). I can use it with 3 different sanding belts - an 80-grit to shape the blade and remove any knicks; a 220-grit to put…
Read the complete tip →“I turned a rolling walker into a handy, portable workbench. It’s sturdy, lightweight, easy to maneuver, and quickly folds up for storage. I used a piece of scrap aluminum to make the 16 by 24-in. top and screwed…
Read the complete tip →Overhead oil tanks, drip collectors and organized filters keep Howard Ewen’s shop clean and neat, making oil changes a lot easier. With 4 IH 4586 diesels, around 30 Olivers, 5 or 6 farm trucks, 3 pickups and several…
Read the complete story →Paul Petrocchi at American Windmill restores gear cases to better than new with a special oil seal and roller bearings.
Read the complete story →“The traditional ‘motor-on-the-top’ air compressor that I got from a friend had a rusty 80-gal. tank and bad seals, so I decided to fix it up rather than throw it away,” says Mark Rinke, Lakeville, Minn.
Read the complete story →“I used to have a lot of problems with gummed-up carburetors on equipment that gets used infrequently. I eliminated the problem by using Star Tron fuel enzyme before storage. It works much better than Seafoam or Stabil and…
Read the complete tip →“I use old refrigerator produce drawers to store bolts, home clamps, springs, etc. They fit into shelves I made between studs in my shop.”
Read the complete tip →“I set up a battery charging station using an old Dewalt tool case. Using a rotary tool, I cut out the dividers in the case to make room for the chargers, which are held in place by a…
Read the complete tip →“Here’s a quick tip that I use all the time around my shop and farm equipment. I buy shrink-wrap plastic in 4-in. wide rolls
Read the complete tip →The article in our last issue on the Zoha grinder disc fitted with chainsaw teeth prompted 87-year-old Niles Schulz of Loweville, N.Y., to send FARM SHOW a photo of a similar grinder disc he made himself about 20…
Read the complete story →“I built these heavy-duty, infinitely adjustable roller stands out of angle iron and square tubing. I use them with my drill press and table saw when handling long material. When spaced 4 ft. apart, they provide a sliding…
Read the complete story →If you need parts for an older lawn or garden tractor, check with HAPCO or Deaven Tractor Parts. If one doesn’t have what you need, the other likely does. Brandon Pfeiffer started restoring a 1966 Deere 110 he…
Read the complete story →“By mounting the stator from a discarded permanent magnet motor onto a wooden plate, I can use it to store small magnetic parts such as drill bits or even sewing pins and needles. I remove the stators from…
Read the complete tip →“It works great for storing the mower deck, snowblower, and landscaping blade on my riding mower, as well as my leaf blower and other accessories,” says Cal Miner about the hospital medication cart he converted into a multi-purpose…
Read the complete story →“Over the years I’ve had trouble keeping small parts separated and organized, especially those tiny screws, drill bits and special parts that disappear when thrown into a drawer. My liking for cigars fixed that problem. Now I use…
Read the complete story →“I use my 2,500 sq. ft. shop to maintain farm equipment, build furniture, and do welding work. I built a 35-ft. long work bench along one wall, but instead of adding shelves or cabinets above I made a…
Read the complete tip →Mike Bengtson of Brandon, Minn., was inspired by ideas in FARM SHOW to use an I-beam frame to hold toolboxes.
Read the complete story →If you need a part for a riding mower, LeRoy Oleson, Jr., likely has it. He has mowers by the hundreds waiting to be parted out and mower parts on shelves numbered in the thousands. His South Dakota…
Read the complete story →“The control gate on my fertilizer speader rusted shut. I oiled it with WD-40 when putting it into storage but it was frozen shut the next time we went to use it. Then I read in FARM SHOW…
Read the complete tip →“I converted a non working upright freezer to a handy winter storage cabinet that I keep in my shop. I use the cabinet for items that shouldn’t freeze, such as paint and other liquids. I spend my winters…
Read the complete tip →If you’re restoring a Cockshutt or Co-op tractor and need parts, chances are very good that Pennsylvania collector Phil Heisey has exactly what you’re looking for. Heisey and his wife, Noreen, have more than 1,000 parts on hand,…
Read the complete story →“The 12-ft. diameter by 36-ft. tall cement stave silo adjacent to my barn looked good, but I didn’t trust it because of its deteriorating staves,” says Minnesota handyman Mark Rinke.
Read the complete story →NEW Hydraulics can provide the hydraulic, fuel line, power steering and A/C tubes and hoses needed to rebuild, restore or customize equipment. Whether you need one tube or hose or multiples, no job is too big or too…
Read the complete story →“I have numbered all my parts drawers and alphabetized my shelves in order. I make up a 3 by 5 index card for each part and where it’s stored. All the cards are in a box so no…
Read the complete tip →“Cutting the pour spout off used plastic jugs makes it easy to store chains tangle-free. I leave the handle on and use different size jugs for different size chains. Metal pails and containers can be used to store…
Read the complete tip →If you’re looking for a used lawn mower or parts, Almost Heaven Lawn Mower Grave Yard in Bluffton, Ind., is a great place to start. It’s a “pick-apart yard,” says Tom McNamara, who helps his son, Scott, run…
Read the complete story →You can turn any seed box tote into a neat, clean waste oil collection system with this new oil collector. The patented Tote-Top Mega Funnel allows you to store all your oil changing tools and supplies such as…
Read the complete story →“I wanted a handy place to store chains on my Allis Chalmers 170 loader tractor, so I bolted an angle iron bracket onto one of the loader arm uprights and then bolted an 18-in. long, 2-in, wide metal…
Read the complete tip →“I mounted a 4-ft. long by 20-in. wire rack on my shop wall to make a handy air tool storage rack. I cut up lengths of pvc electric conduit in order to make customized tool holders that are…
Read the complete tip →The 43-in. long Faithfull flexible driveshaft extends the reach of a power drill. One end fits into the drill’s chuck and the other end has a keyless chuck to slip in a drill bit, wire brush, grinding wheel,…
Read the complete story →Roger Podoll has a quick fix for broken throttle or choke cables. If the outer sleeve is broken or too short, splice it with a second piece and slide a new wire through the two. He uses a…
Read the complete story →“I bought a bunch of used office file cabinets and attached them to an outside wall of my shop. They really work great to hold parts and tools,” says Keith Bleicher, Shushan, N.Y. Bleicher found the cabinets on…
Read the complete story →“I came up with a neat way to store aerosol spray cans and other small containers on the wall of my shop. Just cut a 3-in. dia. pvc pipe to about 4 in. long. Drill a 3/4-in. dia.…
Read the complete tip →“I store 50 and 100-ft. long extension cords inside 5-gal. plastic buckets. I cut a 2-in. dia. hole near the top to run the plug-in end of the cord through, tying a knot in the cord to hold…
Read the complete tip →“Our new Path Pro wheel guards snap onto the wheels found on welder carts and rolling toolboxes. They push small obstacles such as cords and welding leads out of the way, to keep the cart or toolbox from…
Read the complete story →“My four chainsaws and the oil and fuel needed for them were cluttering up my shop floor, so I built a chainsaw stand to keep everything organized. It cleared up a lot of floor space,” says Dave Neil,…
Read the complete story →Brothers Will and Ryan Garrett followed their father into the business of repairing radiators. Later, it was their desire for working “outside the box” that got them into custom manufacturing. Fifteen years later Radiator Supply House produces custom…
Read the complete story →“To store long-handled tools, I cut the top off a plastic 55-gal. barrel and fill it with pieces of 4-in. dia. thin wall pvc pipe. The pipe holds the tools separate from each other. For D-handle tools, I…
Read the complete tip →“I store log chains in 5-gal. buckets with the hooks hanging on the edge of the bucket. Makes it easy to grab and go and you don’t have to search for the ends.”
Read the complete tip →“I have a 4 by 8-ft. freestanding workbench which works great, but there was never enough room to store commonly used tools close by.
Read the complete tip →“Instead of buying a magnetic holder for my nuts and bolts, I make my own using a small can and magnets removed from discarded microwave ovens. A typical microwave oven has about 4 good magnets in it. I…
Read the complete tip →Lyle Mack loves gear making so much he’ll even help you make your own. The young machinist set up LM Gear and Machine on his family’s farm to make gears, sprockets, and splined shafts.
Read the complete story →Glen Wasmuth takes his tools to the job, whether in the shop or around the yard. His shop on wheels is loaded with tools of all sizes, from wrenches and bits to grinders, cutting torches, drill presses and…
Read the complete story →“I was a welder for 35 years and always kept a bottle of Vitamin E cream in my toolbox. Everyone in the shop would use it because it worked so well on burns and even cuts. I’ve seen…
Read the complete tip →“I converted an old gas grill that didn’t work any more into a portable table saw stand. I replaced the grill with a piece of 1/2-in. thick plywood and set the saw on top of it.
Read the complete tip →“I bolted my stationary grinder onto an inexpensive 2-wheeler cart so that I can move it around wherever there’s good light and ventilation. The cart also makes the grinder easy to store out of the way. The base…
Read the complete tip →This fuel system additive is designed to ensure easy starting of equipment that has been sitting for a long time (www.startyourenginesus.com; ph 773 376-4400). It works by adding combustibility to old fuel and removes gum and varnish sediment…
Read the complete tip →“My cousin and I were trying to figure out how to store and apply our home brew mix of 50-50 automatic transmission fluid and acetone that we use as a penetrating oil to loosen up rusted nuts. I…
Read the complete tip →