Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 29, No. 1 (2005)

Vol. 29, No. 1 (2005)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 36–39

34 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip 1 of 2

Ken Scharabok

Individual tip 1 of 2 from this reader’s published contribution.
Ken Scharabok, Waverly, Tenn.

“The jaws on pipe clamps are often too short to get a proper grip. I make jaw extensions on my clamps out of 1/4-in. thick steel plate, 1 1/2 in. wide. I drill a hole through them for the pipe and then arc weld them onto the original jaws. They work fine.

From the archive · Full text
Reader shop tip 2 of 2

Ken Scharabok

Individual tip 2 of 2 from this reader’s published contribution.
Ken Scharabok, Waverly, Tenn.

“I also added an extra handle to the top of an adjustable pipe wrench. I just welded it in place. It’s handy for getting a good grip for turning.”

From the archive · Full text
Reader shop tip

Lloyd Settle

Lloyd Settle, Ina, Ill.

“A fellow in your last issue wrote about how his Deere 4850 tractor was overheating. He’d look at the temperature gauge and it was always running too hot.

“I had the same problem. After replacing the thermostat, which did not help, I checked the engine with an infrared temperature sen-sor and found out that it wasn’t really running hot. It was just fine. The problem was a bad temperature sending unit. I changed it out and had no more problems.”

From the archive · Full text
Reader shop tip

Murray McMillan

Murray McMillan, McMillan Farms, Box 57, Arcola, Sask. S0C 0G0 Canada (ph 306 455-2543; email

[email protected]): “I came up with a way to control the hydraulics on my Deere 4-WD tractor. It’s a must-have product for anyone running an air seeder so you can adjust the fan speed from inside the cab. The add-on hydraulic flow control is easy to install. It consists of a lever that attaches to the hydraulic outlet and a control cable that runs up to the cab.

“I’m selling the flow control for $89.95 (Can.) plus tax and shipping.”

From the archive · Full text
Reader shop tip

Bayard G. Young

Bayard G. Young, Elkwood, Va.

“Here’s an easy way to change your own oil and filters and do other under-body work. I wish I had built this car rack years ago.

“The ramp is 15 ft. long and made out of treated lumber, with 2 by 8’s for the main ramp boards and 4 by 4’s for the uprights. The front post is 22 in. high and I put a stop block at the front of each ramp. The uprights on each side are staggered to balance the load and there are cross boards for strength. I used steel cable to brace the center of the ramp, running between posts on either side.

“When the ramp is not in use, I can just lift it up and store it on its side.”

From the archive · Full text
Reader shop tip 1 of 3

Albert L. Url

Individual tip 1 of 3 from this reader’s published contribution.
Albert L. Url, 4117 E. Briges Road, Elk, Wash. 99009

“I discovered an easy and inexpensive way to test radiators for leaks. I put a shop vac on the blow cycle and blow into the radiator to find out where the leaks are. I cleaned them with brake cleaner fluid.

If they’re small, I use a screwdriver to make the holes bigger. Then I use silicone to patch them up and suck with the vacuum on the radiator to pull the silicone into the hole to form a tight seal. I made repairs this way ten years ago and the radiator is still holding tight.

From the archive · Full text
Reader shop tip 2 of 3

Albert L. Url

Individual tip 2 of 3 from this reader’s published contribution.
Albert L. Url, 4117 E. Briges Road, Elk, Wash. 99009

“The same idea can be used for a cracked engine block. When you put heat to a cracked block and try to weld it, the crack will only get longer. But if you clean the crack off and buff or grind it a bit and then use a shop vac to suck caulking in, the caulking will expand and contract with the cast iron and the block will never leak again.

From the archive · Full text
Reader shop tip 3 of 3

Albert L. Url

Individual tip 3 of 3 from this reader’s published contribution.
Albert L. Url, 4117 E. Briges Road, Elk, Wash. 99009

“A seam leak is harder to find because they’re usually very fine. I use Varivain - a plastic coating designed for furniture - to plug seams. Works great.”

From the archive · Full text
Reader shop tip

Henry M. Zubrzycki

Henry M. Zubrzycki, Jasper, N.Y.

Henry likes the Facet electronic fuel pump he installed on his 1962 Deere dozer and also on his 1954 Farmall Super A (Purolator Facet, Inc., Greensboro, N.C. ph 800 852-4449 or 336 668-4444; www.purolator-facet.com).

“Both tractors originally had no fuel pumps. They were gravity-fed. As a result, if I drove them uphill without a full tank of gas and stalled, I could end up going backward. The tractors start much better now.

“The fuel pump operates on 12 volts, which worked out well since I had already converted both tractors to run on 12 volts. The pump comes with all the necessary hose connections as well as mounting hardware. It’s small enough that you can mount it almost anywhere.

“I got the idea after my neighbor installed one on his 1936 General Motors dozer tractor. It had a mechanical fuel pump that was worn out, and he couldn’t find a replacement. I bought both pumps at a NAPA store and paid $39 apiece for them.”

From the archive · Full text
Reader shop tip

Arnold Heeren

Arnold Heeren, German Valley, Ill.

“I read about the money C.F. Marley spent at a Case-IH dealer for two hub bolts for an old IH 706 tractor (Vol. 28, No. 5). I had the same problem with my IH 756 tractor and I found what I needed for just a few dollars at the Fastenal Co. (1261 Grant St., Freeport, Ill. 61032 ph 507 454-5374; www.fastenal.com). The company’s stores stock about 356,000 products, including all kinds of threaded fasteners such as screws, nuts and bolts.

From the archive · Full text
Reader shop tip 1 of 2

Bill Wilson

Individual tip 1 of 2 from this reader’s published contribution.
Bill Wilson, 44 Gable Road, Thompson Falls, Montana 59873 ph 406 827-3006)

“I mounted a pair of standard overhead chain hoists perpendicular to each other on the ceiling of my shop. Both hoists slide back and forth on separate trolleys. I’ve used them to put a new clutch in my tractor and to lift an engine out of a pickup. The perpendicular angle of the hoists really comes in handy. For example, when lifting an engine out of a pickup I can use one hoist to hold the front part of the engine and the other hoist to hold the back part. Once the engine has been lifted out of the pickup, I can use the other hoist to move it in the other direction out of the way. If I want I can move it all the way over to my welding table.

From the archive · Full text
Reader shop tip 2 of 2

Bill Wilson

Individual tip 2 of 2 from this reader’s published contribution.
Bill Wilson, 44 Gable Road, Thompson Falls, Montana 59873 ph 406 827-3006)

“I love doing mechanical work but hate looking for shop tools, so I used a 4 by 8-ft. sheet of plywood to come up with my own two-sided toolboard. It mounts on an angle iron frame and rides on rollers. It lets me roll my tools right out to whatever I’m working on.

“It’s really handy. As soon as I’m done using a wrench I put it right back on the toolboard instead of laying it down somewhere. Whenever I need to use that size wrench again, I know right where it is without having to look for it. The toolboard is narrow enough to fit through a 32-in. wide door. I keep end wrenches and sockets on the front side. All the sockets and end wrenches of the same size line up vertically. So, a 5/8-in. impact socket will have a 5/8-in. standard socket immediately above it. Impact wrenches and hammers, hacksaws, etc., are on the back side of the board.”

From the archive · Full text
Reader shop tip 1 of 2

Murray Scea

Individual tip 1 of 2 from this reader’s published contribution.
Murray Scea, Campbellford, Ontario

“I’ve found that ordinary gutter hangers work great on my shop wall for storing stuff. I use them to store extension cords, hoses, garden tools, jumper cables, oil changing pans, etc. They’re even strong enough to hold tires.

From the archive · Full text
Reader shop tip 2 of 2

Murray Scea

Individual tip 2 of 2 from this reader’s published contribution.
Murray Scea, Campbellford, Ontario

“I use an ordinary hand cart to move my electric welder around my shop so I don’t have to carry it all the time. I mounted a swivel wheel on front of the welder. Then I removed some screws from the bottom of the welder. I drilled corresponding holes into the carrying plate at the bottom of the cart. After placing the welder on the cart I put the screws back in through the bottom plate.”

From the archive · Full text
Reader shop tip

Nancy C. Hainline

Nancy C. Hainline, Springfield, Mo.

“Our Deere 430 tractor and pull-type sickle mower make a good mowing combination. However, we kept having problems with the sickle mower falling off the tractor. The mower hitch is supposed to fasten onto knobs on a metal plate located at the bottom of a hydraulic tank on the tractor. The problem was that bolts on the tank weren’t strong enough to take the vibration of the mower and kept breaking off. As a result, a lot of hydraulic fluid leaked out of the tank.

“To solve the problem my husband welded in new studs and double nutted them. Then he welded a brace bar that extends from the hitch up to the tractor to stabilize the vibration. The bar is angled at both ends and welded to the outside, which keeps the vibration down.”

From the archive · Full text
Reader shop tip 1 of 2

Richard “Red” Guthrie

Individual tip 1 of 2 from this reader’s published contribution.
Richard “Red” Guthrie, Early, Texas

“If you’re a hunter and reload your own shells, the vibrating brass cleaner that you use on your shell cases can also be used to clean other small parts that are corroded or dirty. If you just pitch them in and give it time, they’ll eventually look shiny as new.

Shop feature stories

From the archive · Full text
Feature story

Chain Oiler For Round Balers

Featured source: Bayard Young

“I came up with an easy and inexpensive way to keep chains from wearing out on my 1981 New Holland 847 round baler. I bolted an oil reservoir onto the endgate that automatically applies a steady stream of oil to chains every time I raise the endgate,” says Bayard Young, Elkwood, Va.

Young enclosed the ends of an 8-in. dia. steel tube with steel plates and then bolted the plates to the top of the endgate. He attached valves fitted with rubber hose to both ends of a 1-in. dia. pipe mounted parallel to the oil reservoir and about 1 ft. ahead of it. A vertical breather pipe mounts above each valve.

“It cost only about $100 to put together,” says Young.

“My neighbor Richard Dwyer did the welding work on the tube. It took a little experimenting to get everything to go just right. The breather pipes have to be long enough to keep oil from spilling out of them whenever the tailgate is raised. I put the pipe in the middle of the tube, which can be a problem on hilly ground because all the oil flows to one end of the tube. It would probably work better if there were two pipes coming out of the tube, one at each end.”

Contact: FARM SHOW Followup, Bayard Young, 18172 Youngs Lane, Elkwood, Va. 22718 (ph 540 399-1405).

From the archive · Full text
Feature story

Dirty Oil “Crusader” Sells State-Of-The-Art Filter System

Featured source: Doug Mickelson

Doug Mickelson is a crusader for cleaner engines who has a state-of-the-art oil changing and filtering system that he says is unlike anything on the market. Mickelson will also tell you things you won’t hear anywhere else, such as, “The new oil you buy is often as dirty, or even dirtier, than the old oil you’re taking out.”

His system lets you filter new oil before it goes in and also “repurifies” used hydraulic oil back to original specs so it can be reused.

“This one machine will work on any weight or type of oil without cross contamination. It makes oil changes easier so you’re likely to do it more regularly,” says Michelson.

His Oil Transfer system has a bank of filters so that whenever you switch from one type of oil to another, you use a separate hose and a separate filter assembly. All filter assemblies have pressure gauges to indicate tank or drum. The pan has a removable 180-micron stainless steel cloth insert through which dirty oil is filtered before it’s pumped out.

The system also includes a transparent 27-gal. new oil dispensing cart with a light on it for night time work. The cart rides on a pair of 10-in. pneumatic wheels and has a 23-ft. dispensing hose. An electric-driven 3-gal. per minute pump mounts on top of the tank. A 97 percent accurate digital meter measures and dispenses oil from the cart.

“It eliminates the need to carry jugs of oil up ladders to fill big equipment. And it ensures that you’re not getting contaminants into engines, which are built with much tighter tolerances today than in the past,” says Michelson.

“Most farmers don’t realize the level of contaminants in the new oil they’re putting often careless in reusing containers,” says Mickelson.

“Many of the 55-gal. barrels that farmers return to their dealer get reused, even though they have water and gravel and sludge in them. It’s pretty hard to clean them out completely.”

Michelson also thinks most farmers are missing the boat by not recycling dirty hydraulic fluid.

“No one promotes the idea because they want to sell you new oil. But there’s really no reason not to reuse it if you filter it properly,” he says.”

He says Caterpillar is recycling all new hydraulic oil in their own in-house equipment.

“They run some of their equipment for more than 10,000 hours on the same hydraulic fluid, filtering it over and over again.”

Problems with new fluid have become so bad that Caterpillar factories now require that new oil be of a minimum cleanliness level of 16 13 ISO code in order to satisfy the warranties on its new equipment. But typically, new oil is far dirtier.

“One Caterpillar labo-ratory manager told me that before they started scrubbing their new oil in house, he was telling his service people to leave old hydraulic oil in because it was cleaner than the new oil.”

Michelson’s Oil Transfer System sells for about $3,000. His website is full of detailed information.

Contact: FARM SHOW Followup, Doug Mickelson, Oil Transfer Systems LLC, 7009 Sunnyside Street, Horace, N. Dak. 58104 (ph 701 282-3617; website: www.oiltransfer.com).

From the archive · Full text
Feature story

“The Best Scraper On The Market”

Featured source: Jim Howe

After Jim Howe, Jr. bought what Gemplers calls “The Best Scraper On The Market” from the company’s mail order catalog (www.gemplers.com), he wasn’t happy. So he rebuilt it in a way that lets it live up to its headline.

He liked the fact that the blade of the scraper was made of lightweight poly that could be reversed for extra long life. What he didn’t like was that the handle was attached parallel to the blade. He couldn’t get any leverage for pushing.

So with an 18-in. piece of 1 1/2 by 1 1/2 angle iron, some flat stock and a few bolts, he modified the scraper so that the handle runs into the back of the blade, braced by four angled struts.

“Now I can really push snow, manure or whatever,” he says.

Contact: FARM SHOW Followup, Jim W. Howe, Jr. 22 Maple St., East Windsor, Conn. 06088 (ph 860 627-6515).

From the archive · Full text
Feature story

First-Of-Its-Kind Backpack Welder

Featured source: A. Blazina

Here’s a welder you can take anywhere because you carry it on your back!

“There’s never been anything like it on the market,” says A. Blazina of ZENA, Inc., about the company’s new lightweight go-any-where welder.

The backpack welder is powered by a small 2-cycle gas engine that was originally developed to power racing go-carts and military drone aircraft. It’s a precision engine that Blazina says has a lot of power, yet it’s light enough to keep the entire weight of the welder down to 62 lbs.

Blazina, who also manufactures the popular ZENA welder that can be fitted to existing engines, including motors in tractors and pickup trucks or even garden tractors, says the 150 amp, 100 percent duty cycle backpack welder does the job of big commercial welders that cost considerably more.

“The great thing about this welder is that you can take it anywhere. For example, you can ride out with the welder on your ATV rack to fix equipment in the field and then carry the welder to other locations where even your 4-WD can’t go. You’re not tethered to anything,” says Blazina.

“We already have a customer flying these units in small helicopters to remote locations, climbing 200-ft. towers with the welder on their back to make repairs that previously could only be accomplished with large welders carried to the site by huge, expensive-to-operate cargo helicopters. Just the welding cables for those kind of setups would weigh more than the backpack welder.”

The welder, which just came on the market this winter, sells for $2,595.

Contact: FARM SHOW Followup, A. Blazina, ZENA, Inc., 330 Club Springs Road, Elmwood, Tenn. 38560 (ph 615 897-2011 or 877 936-2462; email: [email protected]; website: www.zena.net).

From the archive · Full text
Feature story

“Tasteless” Way To Siphon Gas

Featured source: Four Wheeler Magazine

Here’s an idea we spotted in Four Wheeler Magazine that makes siphoning gas easier and safer.

Just buy a gas hose like those used on out board boat engines – the ones with a primer bulb - and fit tubes to each end. It’s that simple.

From the archive · Full text
Feature story

Litter Holder Uses Free Plastic Bags

Featured source: Roger Stein

Here’s a way to make use of those plastic bags that retailers give us to carry our “stuff”.

The Plastic Bag Hanger, created by Roger Stein, Fargo, N.Dak., makes it easy to hang up bags anywhere to hold trash. The plastic bar is 9 by 1 1/2 in.

Two screws or double-sided tape attach it to any flat surface. Plastic bag handles hang on notches at each end of the bar.

“The beauty of it is that they can be used almost anywhere inside or outside,” he says of the idea, which he and his daughter created while fishing.

Stein is looking for a company interested in licensing the product.

He sells a set of three for $6.00 which includes S&H.

Contact: FARM SHOW Followup, Roger Stein, Tri-Ota Enterprises, 3944 15 Street South, Fargo, N. Dak. 58104 (ph 701 232-3757; email: [email protected]; website: plasticbaghanger.com).

From the archive · Full text
Feature story

Replacement Pump On NH Sicklebar

Featured source: J. Blaine Runner

“The sicklebar on our New Holland 1475 16-ft. haybine is powered by a 1,000 rpm pto-driven 30 gpm hydraulic pump running at 3,000 psi. The pump attaches to a pto coupler, which hooks up to the tractor pto. On Deere tractors especially, the pump tends to vibrate too much at the high 1,000 rpm speed.

“I solved the problem by replacing the New Holland pump with a Prince 40-gpm pump that runs at the 1,000 pto speed with 2,500 psi capacity. The itself pump fits right over the pto shaft, eliminating the vibration problem. I lowered the hydraulic oil pressure by backing off the bypass valve on the cutter one quarter turn. The cutter performs adequately and the compromise protects the pump, which is not rated for over 2,500 psi operation. I also had the holes for the torque bar mounted on the pump tapped to 1/2-in. bolts instead of the standard 3/8-in. bolts for better reliability. A second advantage is that to pump 30 gal. per minute the pump only has to operate at 3/4 speed – 750 rpm’s on the pto and 1,575 for the tractor. No need to run the tractor at full rpm’s. The Prince pump cost $400 and has served two seasons with no problems.”

Contact: FARM SHOW Followup, J. Blaine Runner, 89641 Runner Road, Ashby, Neb. 69333 (ph 308 458-2267).

From the archive · Full text
Feature story

PVC “Oil Caddy” Works Great For Changing Oil

Featured source: Chris Kornkven

PVC tubing works great for adding oil to engines, transmissions and rear ends where there’s not enough room to pour out of a standard quart oil container, says Chris Kornkven, Helenville, Wis.

Kornkven made an oil caddy out of a 6-in. dia., 3 1/2-ft. length of pvc pipe. He got the idea after reading about a fire extinguisher used for changing oil in FARM SHOW (Vol. 27, No. 5). Both ends of the pipe are capped off. He threaded a valve stem into the top cap and screwed a small outlet into the bottom that’s connected to a piece of flexible tubing with a valve at the end. He unscrews the top of the pvc tube to add oil and then uses an air compressor to put a bit of air pressure in it.

“It can hold up to 2 gal. of oil. It really comes in handy when changing oil on my truck since the Cummins engine holds up to 11 quarts. It takes only a small amount of air pressure, about 10 to 15 psi.

“I also built a smaller 18-in. long model which I use to hold five or six quarts of oil. I spent about $10 to $20 to make each unit.

“It eliminates having to deal with funnels and having half empty containers of oil sitting around. Because the pvc pipe is closed, as long as I keep the plug on dirt can’t get into the oil.”

Contact: FARM SHOW Followup, Chris Kornkven, N6280 County P, Helenville, Wis. 53137 (ph 920 699-2376).

From the archive · Full text
Feature story

Next Best Thing To A New Paint Job

Featured source: Jim Deardorff

“You can get an extra $1,000 for a shiny combine over a dull one,” says Jim Deardorff, president of Superior Coatings, about a product called Kleen Kote that stops rust and re-stores old paint.

Deardorff is a paint specialist who has also developed a black light paint process (Vol. 24, No. 1) and a new sandblast media that uses walnut shells (Vol. 26, No. 3).

Kleen Kote is a spray-on product which he says not only adds years to a paint job, but can add dollars to vehicles and equipment at trade-in or auction time.

“My biggest sales so far have been to shine up equipment for auctions,” he notes.

While Kleen Kote shines up a paint surface, the micro-emulsion cleaner also gets into surface cracks, cleans them out and fills them in.

“Two of the major causes of paint failure are the salts from roads and sulfates from diesel exhaust,” says Deardorff.

“Detergents used to get grease and oils off are pretty aggressive and can really tear paint up. With Kleen Kote, the contaminates never get a chance to bond with the paint, and you don’t need detergents.”

Deardorff says Kleen Kote cuts corrosion as well. Corrosion begins when moisture migrates through cracks in the paint surface to the underlying metal. In cold climates, the process is speeded up as moisture drawn into micro cracks freezes and expands to make the cracks bigger, allowing in more moisture. By cleaning out dust and dirt and sealing the cracks, moisture is kept away from the metal.

“If you apply it twice a year, you will keep the moisture from getting into the paint,” says Deardorff.

While he advises getting the surface as clean as possible in preparation, the product can be sprayed over dust. If sprayed on thick enough, it will migrate through the dust to saturate the paint.

Once the paint is saturated it can be left as is, leaving the surface with a smoky or foggy look. If a glossy surface is desired, Deardorff suggests wiping it with a damp rag before it dries.

“I recommend using a high volume, low pressure spray gun with only about 10 lbs. air pressure at the nozzle for larger applications,” he says.

“That will gently lay it on the surface. If you use a hand pump or Hudson-type spray gun, use a wet rag to wipe it on for a good coat.”

Deardorff suggests the new product is especially valuable when used on farm equipment. Fertilizer, chemical and manure spreaders/applicators are especially subject to corrosion. He says a layer of Kleen Kote will cut corrosion in half.

The basic ingredient in Kleen Kote is a concentrated industrial product from Progressives Industry. Deardorff sells it in concentrated form or mixes it with water and other additives depending on final uses. He recommends a 15:1 mix for general use and 20:1 mix for general maintenance for combines and tractors. For high corrosion potential vehicles, like feed trucks and fertilizer spreaders, he markets an 8:1 product with a corrosion inhibitor added. He does recommend a pretreatment with Chlo-Rid, a salt remover agent, before applying Kleen Kote to farm, fertilizer or road equipment.

“I put it on a car in December, ran it all the way through the winter without washing,” says Deardorff.

“In March, I ran it through the car wash on just the rinse cycle, and it came out shiny.”

Kleen Kote is available from Superior Coatings for $35/gal. in its concentrated form. It is also available by the quart, gallon or bulk amounts in solution. A gallon of 15:1 solution is enough to treat a combine at a cost of $20 plus shipping. A quart of the same at $10 would be enough for a mid-sized tractor.

Contact: FARM SHOW Followup, Jim Deardorff, Superior Coatings, P.O. Box 317, 205 McCormack St., Chillicothe, Mo. 64601 (ph 660 646-6355; email: [email protected]).

From the archive · Full text
Feature story

Brush-On Electrical Tape

Featured source: North American Oil

Brush-on liquid electrical “tape” is superior to tape on a roll because it forms a tighter seal against dirt and moisture and it won’t work loose due to vibration, according to the manufacturer, North American Oil.

“It dries in 5 min. and can’t unravel. It’s ideal when working in tight places,” says company president Cal Yudin.

He says the product is especially useful on battery terminals, especially in cold weather areas where moisture is drawn in by the electrical system. Brush-On Electrical Tape is great for boat trailers and underground irrigation systems, too.

“People even use it to repair vinyl above-ground swimming pools, to coat bleached boat upholstery (it’s easy to thin it), and for coating screws to keep them from shaking loose,” he says.

“This product is made from liquefied PVC chips.”

It also comes in a variety of colors, allowing the user to match color-coded electrical wires. The retail price ranges from $3.99 to $5.99 and it’s available in most automotive and hardware stores.

Contact: FARM SHOW Followup, North American Oil, Cal Yudin, 2200 May Court, Kennesaw, Georgia 30144 (ph 800 554-3014 or 678 355-0575; email: [email protected]; website: www.northamericanoil.com).

From the archive · Full text
Feature story

Farmer “Recycles” School House

Featured source: Dale Flohaug

When Dale Flohaug went to school in a one-room school house as a young boy, he never dreamed he’d spend hundreds of hours in the building later in life. But that’s what happened because he uses the tiny one-room white school house, which is about the size of a single car garage, as his farm shop. The school’s annex, which once served as the cloak, boot and wood room, sits a short distance away and now houses lubricants and miscellaneous tools.

Flohaug’s father, Clarence, moved the buildings to his farm in the 1960’s when the school closed.

The elder Flohaug also made sure that the original windows, lighting and interior siding remained intact. He put strong wire mesh over the windows to protect the glass, attaching hooks through the mesh to hold tools and small parts.

Dale and his wife Gail have added their own creative touches to make the shop even more workable.

• On one side of the shop an old clothes washer cabinet houses the arc welder. The top surface is plate steel with edging made from worn combine rasp bars.

“We made this to save space, and with the heavy top and sides, we could hit it with a maul and not do any damage,” says Dale.

• “Changing big truck or wagon tires was always a problem for one man,” says Dale, “and we’re always concerned about safety. That’s why we mounted a bead breaker to the frame of the shop. It gives one person extra leverage and it’s a lot safer than doing this with a maul and bar.”

• “Plastic tool bins are good, but metal ones are better because they don’t crack and break,” says Dale.

“My dad made these bins 40 years ago from cups that were riveted on a grain belt. They’re still in perfect condition today.”

• Gail Flohaug doesn’t do as much canning as she used to, but her jars and lids are put to good use. By mounting the lids to the underside of shelves, she and the hired help don’t have to spend as much time looking for odd size nuts and bolts.

Says Dale, “I started my education in this building more than 40 years ago, and I’m still learning how to do a better job repairing things today. I guess it’s only right that we can preserve this ‘learning’ heritage and have the building serve us as a great farm shop.”

Contact: FARM SHOW Followup, Yellow Rose Farm, Dale and Gail Flohaug, Aneta, N. Dak. (ph 701 322-5677).

From the archive · Full text
Feature story

Small Machine Lift Platform

Featured source: Lloyd Meffert

Lloyd Meffert, Hettick, Ill., bought an air-powered auto lift from Harbor Freight Tools (www.harborfreight.com; ph 800 444-3353) and then built a platform for it to work on ATV’s, lawn mowers and other machines.

He made the 6-ft. long platform out of 1-in. sq. tubing with 10-in. legs in each corner and a drive-on ramp at an end. Plywood run-ners for the tires go down either side.

The platform simply rests on top of the lift arm so it can be removed easily when not being used.

Contact: FARM SHOW Followup, Lloyd Meffert, 25921 Mt. Ragan Rd., Hettick, Ill. 62649 (ph 618 778-5519).