Jim Taylor
“I remove the magnets out of old audio speakers and screw them to the bottom of a shelf by my workbench. It works great to keep track of small parts when I’m working on a project.”
Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 36–39
37 selected entries · Complete text of selected entries
This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.
“I remove the magnets out of old audio speakers and screw them to the bottom of a shelf by my workbench. It works great to keep track of small parts when I’m working on a project.”
“When changing oil on a tractor in the field, you can use your belt as a filter wrench if you forget to bring a wrench with you. The wider the belt the better.”
“To clean rust out of sprockets and hubs, I use a 3/8-in. dia. rod about 6 in. long. I use a hacksaw to cut a slot in one end about 1 in. deep. Then I take a piece of emory cloth and slide it into the slot. You can then put the rod in a drill and it will wrap up into a circle. Then insert it into the hub to clean it out.”
“Last summer we did a lot of haying. I ran a 150 hp. White diesel tractor on the mower at 6 1/2 mph using only 2 gal. of fuel per hour. Our White 80 hp American ran on 1 gal. per hour. We credit this to a slower engine speed and the fact that White tractors have 18-speed on-the-go transmissions. They have 15 speeds up to 10 mph.
“My advice to people trying to save money on fuel is to throttle back. Don’t run any more than you really need on your job. Most bigger diesel tractors shouldn’t run at over 2,000 rpm’s for good economy.”
“A good idea I had when I built my shop was to insert a 4-in. sq. steel tube post into the ground before the floor was poured. There’s a flat steel plate on top for mounting a large vise. This stand alone vise has plenty of room around it so it’s easy to work with. And no heavy workbench is required for mounting.”
“I came up with a portable chainsaw sharpening vise by bolting a small vise to the top of a 3-ft. high steel pipe, which is welded into an old car wheel hub that serves as a stand.
“To provide more sharpening area, I welded in new material to lengthen the vise jaws by about eight inches. To sharpen the chain, I just the clamp it into the vise and use a file to sharpen the area inside the vise. Then I loosen the vise jaws and sharpen another section of chain until I’ve gone all the way around it.
“It really comes in handy because I can use it anywhere and even haul it in my pickup when cutting firewood in the woods. A metal tube welded onto the pipe serves as a handy place to keep saw files.”
You can do anything with duct tape, except for cutting it off the roll in a smooth, straight piece. This new product solves that problem. The Tape Wrangler is like a giant scotch tape dispenser for duct tape. The tape roll fits on a spool and pulls off across a cutting blade that keeps the cuts neat and straight, without any partial tears. It even lets you tear duct tape one-handed. The caddy can be mounted on a wall or bench top, or clipped to a belt so you can carry a roll with you as you work on a job. It’ll hold a 70-yard roll of 2-in. tape.
Sells for $25.
The company also offers flexible magnetic tape that allows you to put a magnetic backing on nearly any object around your home, shop or office. You get 25 ft. of 1/2-in. wide adhesive-backed magnetic tape. Just cut a strip off with scissors or hobby knife, peal off the backing and stick it to whatever ob-ject you want to stick. You can also stick up a long strip of magnetic tape on the shelf above your workbench for a place to stick screws while you’re working on repairs.
Sells for $9.50.
This company offers an “at-your-fingertips” hammer holder that eliminates “leg bang”. Prazi’s Hammer Holster clips onto any tool or waist belt with the hammer head inside the holster. When you’re ready to use the hammer, you grab the handle, not the head, so it’s ready to swing.
The holster is reversible for right or left handers, and it’s adjustable so you can put the hammer handle exactly where you want it. The unit can be used with any style of hammer. You can order it on the company’s website for $9.95.
“I have a problem with the feederhouse on my Deere 6600 combine. Soybean dust and stems build up inside, holding up the drum so it won’t feed evenly. Because of the uneven feeding, I broke two idler arms on the variable cylinder sheave before I started cleaning out that spot at the leveling adjustment with a piece of wire every time I unload. I can only cover about 50 acres before I have to take off the header and do both sides. Any suggestions on how to solve this problem would be appreciated.”
“When the original engine on my Case 1816 skid steer loader went bad, I replaced it with a new Honda 24 hp twin cylinder engine. It now runs much smoother and quieter and has a lot more power. The new engine came complete with a starter, and the wiring and control cables fit without requiring any alterations. I did run a new wire from the starter to the ignition switch, bypassing the original starter solenoid.
“The new engine fit in the available space with about an inch of clearance all around. I drilled new mounting holes in the existing motor mount brackets. The original 1 3/16-in. dia. pulleys driving the hydraulic pumps didn’t fit the new 1 1/8-in. dia. shaft, so I purchased new double and single sheaves with a taper lock adapter to fit the new driveshaft. I drilled and bolted the new sheaves together and mounted them together on the one taper hub. Since the new engine’s driveshaft was mounted slightly higher than the crankshaft on the original engine, I bought a 1-in. longer drive belt for the bottom pump and a 1-in. shorter belt for the top pump. The original side pump belt-fit without requiring any alterations.
“The muffler system required the most custom work. I mounted a new twin cylinder engine muffler on the frame above the engine and fabricated new exhaust pipes to fit and clear everything. I’d be glad to answer any questions about the installation.”
He built a table specifically for painting tractor parts. He came up with the idea of using expanded metal because it allows the surplus paint spray to flow on through without puddling up.
He was so intent on having a shop with an ad- equate traveling hoist that when building a new shop, he first built the hoist and then the building around it. The hoist measures 16 ft. high up to the rail. The rail itself is an 18-in. I-beam, and it also has 18-in. I-beam uprights. The chain hoist carrier spans 22 ft.
Trolleys at either end of the cross track each mount on four caster wheels, running inside a channel formed by angle iron sides. He says the chain hoist can lift up to 4,000 lbs.
“A cluster of plastic containers, bolted to the frame of our Deere 4640 tractor, provides handy storage for our fire extinguisher, as well as ether and penetrating oil. The containers originally were filled with anti-freeze, motor oil or penetrating oil. After removing the labels I drilled a hole in each container, then bolted the containers all together into a cluster. Then I bolted the cluster onto the tractor, using an existing hole in the frame. It’s important to put washers on the inside to keep the containers from splitting. There is a toolbox on the other side of the tractor, but I wanted to keep these items separate for quicker access.
“A used tractor headlight bolted onto the steps on the other side of the tractor makes it easier to see and adds safety. The light is wired to the tractor’s lighting system and automatically comes on whenever the tractor’s lights are turned on. My son made a bracket for the headlight and bolted it onto the steps. It comes in handy at night whether the tractor is indoors or outdoors, because any time it’s dark it’s good to have extra light around the steps. For example, standing corn stalks in a field can be easy to trip over but with the light I can see them right away.”
“I have a money-saving tip for anyone who owns a fuel-injected vehicle. Many people complain about the expense of having to replace their fuel pump after only 60,000 to 80,000 miles. But you can avoid the problem just by changing the fuel filter once a year. I have two Chevrolet Blazers with more than 180,000 miles, and I’ve never changed a pump on them, or on any other car I’ve owned. A dirty $10 filter can easily ruin a $1,000 pump.”
“Here’s a trick I learned from my co-workers. If a bolt breaks off in any part, use a dremel tool equipped with a thin cut-off blade to cut a slot in the broken bolt. Then use a screwdriver to unscrew the bolt.”
“It’s always easier to work on trailer lights when they’re energized. So I made a wiring harness that can be operated by a standard 12-volt battery charger. The green and yellow leads are attached to a double-spaced flasher, and the brown lead goes straight to power. When a trailer is hooked up to the battery charger, the tail lights come on, and the brake lights flash as if the hazards were energized. This makes them much easier to repair, and I don’t have to work out in the cold while making winter repairs.”
“I feed shelled corn to wildlife. Adding a handle to the lower side of a 2-gal. plastic bucket makes it easier to scoop the corn out of bulk containers. I use 1/2-in. electrical conduit, flattened at both ends, to make the handle and drill two small bolt holes to bolt it on.
“I narrowed up this shovel to make it easier to dig. At 78 years old and living with arthri-tis, the smaller sized shovel allows me to work in greater comfort. I also welded a full width 1/8-in. thick steel plate onto the back side for my foot to push on.
“After emptying out 1-quart oil bottles, I shove their necks into a 1-gal. jug to catch whatever oil is left in the bottles. I use the collected oil in squirt oil cans.
“A V-belt formed into a loop, and with a washer slipped over it, works great for lifting and moving small logs.
“A great amount of our food is sold in plastic, cardboard, and metal packages. These packages can be recycled into useful items that make our lives easier and also reduce the waste going into landfills. Many of the containers that our eggs and meat come in
can be used to store small items. For example, egg cartons with their tops removed and plastic meat trays can be stored in a wood or cardboard box with dividers to fit.
“I made this heavy duty 20-in. long ma-chete from an old crosscut saw blade. The aluminum handle is attached with three heavy rivets. I’ve used this big knife to cut up to 3-in. dia. tree limbs and also bushes. I keep it on my tractor.”
“I built this numbered filing system in my garage for stuff ranging from small tools to light bulbs. The plywood shelf is about 20 ft. long and 20 in. deep and is supported by a series of metal brackets. I keep cardboard boxes on the shelf, all numbered in Roman numerals. A file-sheet, mounted on the garage wall at one end of the shelf, tells me what’s in each box so I know where to look for a particular item. It sure beats having to thrash through all those boxes to find what I want. I painted both the boxes and the shelf white to match the color of my garage walls. I keep lawn mower parts in one box, rags in another box, etc.”
“While restoring a 1939 John Deere B tractor I repowered it with the engine from a Deere 212 riding mower. I removed the tractor’s pistons, rods and block, then made a plate and put it on the crankcase so it holds oil. I plugged the holes in the crankshaft with JB Weld to provide oil pressure to the main bearings.
“Then I removed the flywheel and cut a 5/ 8-in. wide V-belt groove in it. I used a centrifugal clutch like you’d use on a go-cart.
Then I installed a jackshaft between the engine and the Deere flywheel in order to get the proper gear ratio. It lets the tractor’s clutch and transmission work without any changes.
“This tractor has no trouble pulling a trailer load of children in parades or taking them on hay rides. I drive it to our local coffee shop on nice days just for the fun of driving it.
“I’d be happy to talk about the conversion. Readers can call me at 580 363-4189 or 956 233-4695.”
“I always have problems taking tires off wheel rims. I find that when I spray the edge of the tire with WD-40 the tire will come right off later. It also makes the tire easier to mount because it’s softer and more flexible.
“The rear wheels on my old Allis Chalmers B-10 tractor are mounted with bolts instead of studs and it was always difficult to line them up. To solve the problem I put a small punch in one hole as I slide the wheel on. The punch helps hold the wheel up, and also makes it easier to line up the holes with the bolts.”
Cleaning dirty air filters is an easy job with this new air filter cleaner that uses a blast of air to instantly clean filters.
The Filt-O-Kleen is designed to clean dirt from paper air filters and was invented by Clifton Wilbourn of Versailles, Mo.
“It’s built strong and is trouble-free. If you go through a lot of filters, it’ll pay for itself in no time,” says Wilbourn.
“It’s not intended to permanently replace the purchase of new air filters. It’ll just make them last longer.”
Each tank comes with instructions and a diagram for easy assembly. Tanks are powder coated inside and outside and are pressure tested at 300 psi.
To clean a filter, the tank is placed on top of the filter with the gasket side up toward the base plate. The volume of air pressure cleans the filter of dirt and debris instantly.
“It’s a safe and efficient way of cleaning paper filters at an affordable price. It does an amazing job of cleaning dirt from filters,” says Wilbourn.
“The air tank can be pressurized and used on filters ranging in pressure from 80 to 125 psi, depending on size of filter.
“In the past, we held the filters in our hands and tried to blow out all the dirt with a hose from the air compressor. You can spend a lot of time cleaning filters this way and possibly damage the paper in the filter. The Filt-o-Kleen works much better and it takes less time, too.”
Two models are available. An 11-gal. model sells for $290 plus S&H, and a 7-gal. model for $260 plus S&H.
Contact: FARM SHOW Followup, Clifton Wilbourn, 22875 Highway TT, Versailles, Mo. 65084 (ph 573 378-5723; wilbourn @netscape.com).
This patent-pending “Tractor Pac” tool tote hangs on the back of a tractor seat to hold a wide variety of tools in nine pockets of varying sizes.
Made from tough nylon, it’ll hold gloves, a water bottle, spray bottle, pruning shears, and just about any other tool. One of the storage pockets also has a hook and loop closure to secure a ball of string or twine for easy dispensing. In addition, there are two 18-in. hook and loop accessory straps for bigger items that won’t fit in a pocket.
Tractor Pac fits most full height seats. Sells for $24.95 plus S&H. Dealer inquiries are welcome.
Contact: FARM SHOW Followup, Innova Products Company, De Forest, Wis. 53532 (fax 608 846-2655; [email protected]; www.innovaproducts.net).
The balcony storage area in Ron Mickle’s shop is much more useable now that he can get there by elevator.
The shop balcony area is 8 ft. deep and 25 ft. long.
“It’s 80 inches off the floor, so lifting anything up for storage presented a problem for someone who’s only 5 ft. 8 in. tall,” says Mickle.
“Now I can ride up to the bal-cony with whatever I want to store.”
He made the elevator-lift using a no. 1700 Warn winch, some purchased steel, two old riding lawn mower tires and two small caster wheels. The winch is powered by a 12-volt battery and is operated by a remote controller attached to a 10-ft. long cord.
“The unit converts from a forklift to a 3 by 4-ft. platform, so I can use it as a work bench for a tiller or snowblower at standing height. No more lying on the ground to work on small equipment or to change the oil,” says Mickle.
The 3 by 4-ft. platform is contained by a pair of wooden 2 by 4’s on either side and held secure by 1/8 by 2-in. steel straps.
A pair of pulleys give the elevator a 3 to 1 reduction on the cable lift, slowing it down and adding to its lifting ability. The winch is rated at 1,700 lbs.
“It goes up at a nice, comfortable slow speed,” says Mickle.
“A lever-operated brake is used to take the weight off the rear tires and hold the unit steady as I ride it up. The system works on an overcenter principle. Pulling up on the lever drives a pair of steel rods into the floor, and lifts the back end of the elevator 3/8 of an inch, which is just enough to take the weight off the tires so the unit can’t slide.
“I’m very happy with it, and my friends think it’s pretty snazzy,” says Mickle.
“I spent only about $300 to build it. I use a handle on back of the elevator to move it around.”
The lift carriage is made from 2-in. sq., 1/ 4-in. thick tubing. The mast is made from 11/ 2-in. sq. tubing and with 3-in. wide, 3/16-in. thick steel plate.
Contact: FARM SHOW Followup, Ron Mickle, S30 W37174 School Section Lake Rd., Dousman, Wis. 53118 (ph 262 965-2479; [email protected]).
A personal quest to convert his vehicles to burn waste vegetable oil led Oz Cheek to become a distributor for Dieselcraft oil cen-trifuges. Along the way he discovered they’re also a great way to completely eliminate con-ventional oil filters on gas and diesel engines.
“They do a better job of filtering out both water and solids, improving engine performance and longevity,” says Cheek.
The fact that the centrifuges don’t have any parts that need to be replaced appealed to Cheek.
“No more filters to throw away. That’s the big thing,” agrees John Nightingale, Dieselcraft’s owner.
Involved in the manufacturing business for 30 years, Nightingale started Dieselcraft in late 2002.
The centrifuge is an old concept. A rotor that looks like an upside down Rainbird sprin-kler spins inside a drum at about 7,000 rpm’s. The solids stick to the rotor and the clean oil gets pumped through the system.
“It looks like peanut butter stuck to the rotor after waste vegetable oil runs through it,” Nightingale says.
Though the centrifuges were initially marketed for oil filters in industrial vehicles and semis, the interest in recycling vegetable oil has sent sales soaring, he says.
The size of a half roll of paper towel, the centrifuge also fits in passenger vehicles and tractors (hydraulic lines as well) and other equipment to replace standard oil filters. They come with brackets and can be mounted in several locations near the engine. Cheek has added them to cars in his collection, from Studebakers to a Jaguar.
Installing a centrifuge requires additional plumbing. Most people add a T to the place where the oil pressure sending unit attaches, Cheek says. Either rubber hydraulic hose or steel lines can be used to connect to the cen-trifuge. Regular oil filters are left on, but don’t need to be changed very often because the centrifuge does most of the work.
“Anything you can do to extend the life of your equipment to me is good insurance,” Cheek says. He simply cleans out the centri-fuges every 3,000 to 5,000 miles.
“They’re easy to take apart. You just clean and wash the rotor and put it back in,” Cheek says.
“Regular oil filters catch solids down to 35 microns in size. These go down to less than 1 micron. It’s common sense that if you’re taking 350 percent more particulates out of the oil, you’re reducing abrasive material and the life is going to be extended.”
Nightingale has distributors in various re-gions of the U.S., and centrifuges are sold for a variety of applications, from the marine industry and backup generators to industrial equipment and personal vehicles.
The centrifuges cost $289, including brackets and hardware for the smallest unit (OC-20). A larger unit, OC-50, handles 110 gph and costs $479. The largest centrifuges, OC-200, for industrial equipment start at $1,550. Contact: FARM SHOW Followup, Dieselcraft, John Nightingale, P.O. Box 7670, Auburn, California 95604 (ph 530 823-7075; [email protected]; www.diesel craft.com).; or Oz Cheek, 899 Mica Dr., Carson City, Nevada (ph 775 720-3555; [email protected]).
If you plan to buy a diesel-powered vehicle in 2007 or beyond, be aware that you’ll need to use a new heavier duty motor oil designed for low-emission diesels with particulate traps.
While specially formulated for the new engines, the CJ-4 oils are also backward compatible to older engines.
“All industry experts say that the new CJ-4 category is the most robust category of lubricants from a performance standpoint that has ever been put out in the marketplace,” says Bob Theisen, technical service manager, CHS.
“They offer great improvements in wear protection, oxidation protection and in ability to handle soot. That is as important for old engines as new.”
The new oils have lower levels of sulfated ash, phosphorous and sulfur (SAPS.) Higher levels of SAPS can clog the particulate filter on the new engines. In the past, it was SAPS that neutralized acids and prevented wear. The new ultra low sulfur diesel fuel reduces acid levels in today’s fuel, and other additives replace the benefits lost with lower levels of SAPS.
The new oils are expected to cost 10 to 15 percent more than previous lubricants.
“They’re definitely worth the increased cost,” says Theisen.
“Ultra low sulfur diesel fuel has gotten into the market a lot quicker and is distributed a lot wider than people thought.”
CHS, marketer of Cenex lubricants, is so confident in the quality and value of the new oil formulation, it is all they plan to market. Other oil companies plan to continue offering the older generation oils.
Mike Svobodny of Greenway Co-op in southern Minnesota says, “There are very few of the new engines out there yet. Until you have the 2007 engine, you can continue to use the older oils, but we will see a transition to CJ-4 oils as time goes on.”
Theisen says CHS is working to confirm the potential for extended drain use of the new lubricants.
“We are working with customers on used oil analysis,” he says.
“We can’t make a blanket statement that time between drains will dramatically increase, because it depends on how the tractor or truck is used. We can say it adds a good reason to start making more use of used oil analysis programs.”
Contact: FARM SHOW Followup, Robert Theisen, CHS, Inc., CENEX Lubricants, 5500 Cenex Drive, Mail Station 525, Inver Grove Heights, Minn. 55077 (ph 651 355-8443; [email protected]).
Need more power and torque from your diesel engine when the going gets tough? Diesel Propane Injection (DPI) may be the answer. It’s a closed loop ECM (engine control module) that injects propane as needed into a diesel fuel system, such as when pulling a load uphill.
Introducing the propane creates more power and torque. It works like the addition of nitrous oxide in a regular gas engine, explains a company spokesman.
The system was created by MSD, a company known for performance and racing components and is marketed by a subsidiary called Superchips. DPI systems are programmed for each application, so no customization of the existing fuel system is needed, no jets drilled or external adjustments required. GM DuraMax, Ford Powerstroke or Dodge Cummins each require a specific kit designed for that engine.
Kits come with detailed instructions, but the company recommends taking them to a certified dealer, especially to have the propane tank installed. Installation should take no more than an afternoon.
The closed loop ECM can be programmed to kick in at a certain rpm or boost pressure, but is never always on or always off unless disabled by manually flipping the switch on the system. The system also logs engine parameters for monitoring system performance.
A DPI system for a 2003 Chevy CK3500 Duramax 6.6LB7 sells for $1,040.
Contact: FARM SHOW Followup, Super-chips, Inc., 1790 E. Airport Blvd., Sanford, Fla. 32773 (ph 407 585-7000; fax 407 585-1900; www.superchips.com).
Not everyone has the skill or the patience to make their own metal replacement parts for older equipment. But for those who do, a 3-in-1 “Smithy” from Smithy Tools may be just the ticket.
“I’ve used my Smithy for some tough jobs,” says John Fell, San Jose, Calif.
“A while back I lost a pin out of a Massey 300 dozer. It was about 2 1/2 in. diameter and about 12 in. long. I cut a piece out of an old bus axle and made the pin on the Smithy. To buy a pin for an old tractor like that would have cost me a fortune.”
A much tougher project for Fell was a smashed steering gear on a Ford tractor. When the dealer couldn’t find a replacement, Fell took the broken pieces out and chucked them into the lathe using centers on the lathe to line the parts up. He then covered the lathe and other machine parts with wet sacking and a leather welding apron and arc welded the pieces back together. After taking the piece out of the lathe, he ground away the broken metal leaving him with a straight shaft. He then built it up using arc welding, getting it roughly back to its original shape.
“I put it back in the lathe and used the Smithy surface grinder to get it back to its exact original size and shape,” says Fell.
“The people at the New Holland dealership said they couldn’t have done it.”
Starting at just under $1,000 for the Midas 1220, a Smithy 3-in-1 can pay for itself quickly. The combination machine lets an operator shape faces with mirror quality finishes with the mill, cut holes with precision with the drill, and turn cylinders with the lathe. As Fell found, the lathe also works for lining up broken parts.
Fell has a top-of-the-line Granite model. Prices run as high as $3,999 for the Granite 1340-I. According to Michelle Rowe, Smith spokesperson, the Granite line is their best selling and contains features such as a quick change gearbox, cam lock spindle and a 1 1/ 2 hp variable speed motor. However, even the economy line Midas can machine to within 0.0001-in. tolerance.
“I bought my Smithy to replace a lathe with a burned up motor,” says Fell.
“Instead of buying a new motor and a lathe attachment, I bought the Smithy. It isn’t intended for big production runs, and you have to be patient and take small and medium cuts, but my machine has paid for itself over and over again.”
Contact: FARM SHOW Followup, John Fell, Eagle Mountain Ranch, 5550 Felter Rd., San Jose, Calif. 95132 (ph 408 258-5851); or Smithy Co., 170 Aprill Drive, P.O. Box 1517, Ann Arbor, Mich. 48106 (ph 800 476-4849; [email protected]; www.smithy.com).
Owners of Dodge and Ford 4-WD trucks can beef up their front ends, improve mileage, and reduce road vibration by reworking factory front axle assemblies.
“In the 1990’s Dodge and Ford did away with the fixed spindle design bolted to the steering knuckle with replaceable bearings,” explains Jim McGean, president, Dynatrac Products.
“They went to unitized bearing assemblies, sometimes referred to as live spindle assemblies. Essentially they’re non-serviceable units that can cost $350 to $500 to replace.”
The good thing for the average truck buyer is that the units are sealed and lubed for life. However, McGean explains, if the seals break down, moisture and contamination get in and they begin to fail. This can damage brake parts as well.
For most truck buyers this isn’t a problem, allows McGean.
“They’re building trucks for 75 to 80 percent of their customers who may not use them for anything heavier than hauling trash on Saturday,” he says.
“That leaves 20 to 25 percent who need a heavier duty truck. That’s the market we serve.”
Dynatrac has been around for about 18 years and is best known for producing complete custom drive assemblies. The company’s new free-spin hub conversion kits fit Ford and Dodge pickups.
The kits include Timken bearings, cromoly spindles, cast nodular wheel hubs, Warn Pre-mium manual locking hubs, and massive 1 1/2-in. dia., 35-spline outer axle shafts, all made in the U.S.
“The bearings require a little more attention from the owner and mechanic, but all mechanics know how to adjust and lubricate wheel bearings,” says McGean.
The Dynatrac bearings are held in place by steel cages.
“With our bearings, if they start to fail they make noise, and you can drive to where you can get them fixed,” says McGean.
“With sealed units, sometimes the only indication is when the ABS light comes on just before they go, and you’re completely disabled.”
Dynatrac kits for Fords from model years 1999 through 2004 are priced at $1,795 and $1,895 for 2005 and newer models. All Dodge kits are priced at $1,895.
Dodge owners reap the greatest fuel economy, adding 2 to 4 mpg in diesel fuel use. The reason for the improvement is Dodge front wheel drive shafts are constantly spinning, as owners are unable to unlock the hub. The spinning also adds vibration and inter-feres with steering.
“Dodge has 125 lbs. of steel axle shafts, pinion gears and drive shafts rotating all the time, whether in 2-WD or 4-WD,” explains McGean.
“With our Free Spin Hub Conversion kits, Dodge owners report a smoother ride with lighter, easier turning.”
Ford still has the locking hub. However, McGean points out that the OEM hub often fails.
“The locking hubs that come with the Free Spin Hub kits are more reliable and longer lasting,” he says.
Contact: FARM SHOW Followup, Dynatrac Products, 7392 Count Circle, Hun-tington Beach, Calif. 92647 (ph 714 596-4461; [email protected]; www.dynatrac.com).
“You can use it on everything from leaky oil pans or gas tanks to plumbing lines or fittings damaged by freezing,” says Ken Pehovic, Coventry Products, Ocqueoc, Mich., about a new metal patching kit that lets you make leak-proof, dependable repairs on thin steel and copper.
It consists of a flexible, 1-in. wide metal mesh that easily forms to any shape, making it easy to repair inside or outside corners, or curves of a metal part, as well as flat surfaces. The mesh can be easily cut with a scissors to fit the area needing repair. High strength 95-5 solder and a premium liquid flux are then applied to the mesh.
The quick, leakproof repair will withstand heat up to 450 degrees, says Pehovic.
“If you keep a car or truck long enough, you’ll find corrosion and leaks in oil pans, rocker arm covers, fuel tanks, power steering pump reservoirs, cooling system tubing, and other thin materials. Often, these leaks are small and located in spots where the paint or plating finish has worn off and rust has perforated the metal. If the leaking part is still structurally sound and the damage isn’t excessive, it’s much more economical to repair the part than to buy new.”
Heavier castings can also be repaired with the kit, but a propane torch may be required to provide enough heat to complete the repair.
“Copper water lines that freeze usually split along a short length of the tube. If cutting and replacing the damaged section isn’t practical, repairing it with this product is a good alternative. You’re repairing it with materials that are compatible with the copper, and the product is lead-free so it’s safe to use on potable water systems,” he notes.
The kit sells for $10 plus S&H. Contact: FARM SHOW Followup, Cov-entry Products, 15012 Balsam Lane, Ocqueoc, Mich. 49759 (ph 989 734-4990; fax 989 734-2794; www.coventryproducts.com).