Mark Vimont
“I was doing a job where I needed both ends of my flarenut wrench at once. Buying another wrench would have cost $19. So I just cut the wrench in two and then slid pieces of steel tubing onto the stubs. Worked great.”
Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 36–39
27 selected entries · Complete text of selected entries
This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.
“I was doing a job where I needed both ends of my flarenut wrench at once. Buying another wrench would have cost $19. So I just cut the wrench in two and then slid pieces of steel tubing onto the stubs. Worked great.”
“I came up with a quick way to repair belts on my Deere 435 round baler. When I find a cut in the belt, I use a cordless drill to bore 3 small holes above and below the cut. Then I double up a length of nylon mason cord and thread it back and forth through the holes several times and then tie a knot. The mason cord I use is the kind used to plug leaks in car tires (www.tractorsupplycompany.com).
“This fix will last a long time. It works a lot faster than cutting a belt in two and splicing in a new belt section. It’s a quick, economical way to keep on baling.”
“When welding or working under a piece of machinery that requires laying on the ground, I’ve found that a scoop shovel laid upside down makes a great shoulder or head rest.”
“I recently restored an early 1970’s Graveley 816S garden tractor that had been in storage for more than 21 years.
“The tractor was completely disassembled and every part was sand blasted and painted before reassembly. The forward and reverse clutches were replaced as well as the bushings and bearings in the front axle and the rear axle hubs. The 16 hp Briggs & Stratton engine was beyond repair. I ended up installing a 20 hp Honda V-twin engine purchased from Northern Tool, which required only minimal modifications. The new engine runs smooth, and the extra horsepower it provides now makes this an exceptional tractor. In fact, it now looks and runs better than new.”
“I installed a Chevy 350 cu. in. engine in an English-made 1963 Fordson Major tractor, and also made several other modifications that worked out quite well. I put an electric fuel pump on to be able to fit the tractor frame. The tractor has a Case power steering system, a Deere combine governor, and a Pontiac electric fan. I used stainless steel pipe to make new mufflers for the tractor, turning the stock manifolds upside down. I also used 1 1/8-in. flat steel to make an adapter plate for the transmission. I used a lot of stainless steel polished bolts for this project.”
This company offers a new line of automotive manuals on CD Rom for Ford, GM, and Chrysler cars. The manuals make it easy to print out clean pages to work from so there’s no concern about getting valuable factory manuals greasy. The company offers CD manuals for most GM, Ford and Chrysler cars from 1909 to 1981. The manuals are reproduced from the original books, with an easy-to-use menu-driven format that includes all the original illustrations. The company also offers parts locator books and directories of places to buy obsolete or hard-to-find parts for classic or antique cars.
Cole offers a low voltage disconnect switch, a device that warns users of low batteries. The voltage-sensing relay and timer has the ability to shut off battery loads when voltages drop.
According to the company, many times when a vehicle is left idling with onboard loads remaining powered, a battery can become depleted to the point that it can’t serve the starting circuit. The “FlexMod” switch alerts the operator when starting voltages are low and then temporarily cuts off any nonessential electrical loads, conserving amps to start the vehicle. The solid-state accessory measures 4 by 3 by 1 in. and has a service life of more than a million on-off cycles. It’s rated at 10 amps and can handle loads from direct circuits. Or it can drive solenoids and relays for higher-current accessories.
“I solved a problem with the battery and charger for my Sears Craftsman 18-volt cordless drill. The charger has 3 lights – yellow, green and red. Normally when you plug the battery into the charger, the red light comes on. Once the battery is fully charged the green light comes on.
“The problem was that sometimes when the battery was put into the charger, the yellow and green light would come on and the battery wouldn’t charge. Yellow and green lights indicate a defective battery. I found that by plugging and unplugging the power cord about 6 times, the red light would come on and the unit would charge the battery.”
“When using my table saw, instead of pushing the wood being cut with my hand I use a homemade wooden block that’s designed to fit over the saw’s guide bar. The handle off an old crosscut saw is screwed and glued into the block, which is made from 3/4-in. thick plywood and painted white. A side board extends down on each side of the block to the table saw’s surface.”
“I mounted a standard, off-the-shelf 14-in. long toolbox on the hitch of my Kuhn 3-pt. mounted, 8-ft. rotary hay mower. I used angle iron and flat steel to make a mounting bracket for the toolbox that welds to the hitch frame. The toolbox bolts to the bracket.
“I use the toolbox to store mower blades and the wrenches that I use to install them. It eliminates a lot of extra clutter on my tractor. I call it ‘point-of-use’ tooling.
“I also installed an extra guard on top of the bar on which the rotary blades are mounted. Sometimes it’s possible for a rotary blade to bend downward into the mower bar, causing the blade to cut into the gearbox which then loses oil. The extra guards prevent that from happening. I used 3/16-in. thick steel plate to make the guards, mounting one guard between each set of rotor blades.
“After reading in Farm Show about grooving cylinder heads (Vol. 35, No. 4), I decided to try the idea on a Briggs & Stratton 5 1/2 hp engine and found that it worked and was fairly easy to do. I use the engine to operate a water pump for my livestock and it cut fuel use by 20 percent. The photo shows a white mark that looks like a bird’s foot where I used a rotary end mill file on a milling machine to make the grooves in the engine head.
“Basically, the grooved head channels the explosion to the edge of the cylinder. This channeling scours the ring area by creating more effective turbulence. The burn is more complete and more energy gets transferred to the crankshaft. After modification, leaning of the fuel-to-air mix helps maximize efficiency.
“I had problems with sediment in the biofuel I use in my tractor. The sediment settled in the tractor’s factory fuel filter, so I had to change the filter often and it got expensive. To solve the problem, I installed two extra spin-on fuel filters. One is located underneath the tractor’s footboard and the other behind a homemade metal guard.
“The add-on filters I used are the same kind of filters used on many bulk storage tanks. They’re a lot bigger than the factory filter and they catch a lot of sediment so I don’t have to change the factory filter nearly as often.
“My homemade wire stretcher, designed to be used with a come-along, saves a lot of hassle. It’s made from a length of twisted, 3/4-in. dia. metal rod with a hook at each end. A tapered metal ‘gripper’ with a donut-shaped hole at one end fits over each hook.
“I fit the wire under a loose ring on the gripper, then slide the ring up over the wire until the tapered rod grips it tight. The hooks are spaced about as far apart as the distance between two wires in a fence. That way the rod keeps the wire strands separated so they don’t get tangled up.
“Each gripper can be used individually, or I can stretch two wires together at the same time.”
“To discourage rodents from getting under your vehicle’s hood and chewing up wires and insulation, sprinkle about a dozen mothballs around the perimeter of the vehicle. Don’t put any under the hood, as you could get mighty sick when you get back in the vehicle. Also, remember to keep children and pets away.”
Greg came up with a simple solution for tool storage in his crew cab pickup. Although retired, he does a lot of handyman work and likes to have his tools with them. But he didn’t want to have a big toolbox in the box. So he made some shelves that simply rest on top of the back seats in the cab. They can be quickly lifted out to make room for grandkids or guns and they protect the seats from damage that would be caused by placing toolboxes directly onto them.
“I couldn’t find a replacement battery for my old Sears cordless drill. The drill was still in good shape, so I came up with a low-cost way to give it new life.
“I removed the battery from the drill and attached one end of a lamp cord to the battery terminals inside the drill. Then I attached a pair of alligator clips to the other end of the cord, allowing me to hook up the drill to any 12-volt battery.
“It works great and was simple to do. I use it often at our cabin, which doesn’t have any electricity. I also take it with me on my 4-wheeler. I hook it up to a lawn mower battery that I carry around in a box on back of the 4-wheeler. It really comes in handy when I’m at my deer blind.”
After more than 60 years, Forrest Spindler’s homemade drill press still works great. His father Joseph made it while Spindler was serving in World War II. When he got home and took over the family car repair business, he got the drill press, too.
“What parts he couldn’t adapt from car parts directly, like the pulleys and hand tightener knobs, he cast from old pistons he melted down,” recalls Spindler.
“Other pieces like the Morris taper for the chuck were turned on his lathe. The only things he didn’t make were the Jacobs chuck, fan belt and electric motor.”
The base is an old flywheel, and the upright column is a piece of drive shaft. The housing for the drill press head is from parts of an old car frame, cut and welded together. The press table is also made from a flywheel. It is attached to the column with a clamp from a shackle for springs. Loosening the hand cast knob on the clamp lets Spindler move the table up and down to accommodate larger work pieces.
The spindle assembly itself is made from a torque tube from an old truck. A piece of sprocket from a starter drive attached to it controls vertical movement within the shaft assembly. The shaft handle turns a ring gear that turns into the straightened out sprocket.
A double set of ball bearings top and bottom in the shaft assembly hold the spindle in place. Exactly how the spindle is constructed is a mystery to Spindler, as it is encased in the drill head housing and he has never taken it apart.
“It had been set aside for many years,” says Spindler.
“A few years ago, I dusted it off, and it started right up. It still works great.”
Contact: FARM SHOW Followup, For-rest Spindler, 106 8th St. W. Park Rapids, Minn. 56470 (ph 218 732-3170; [email protected]).
“Hanging your welder from a telescopic boom frees up shop space and makes welding jobs easier. The welder hangs above your work, so you don’t have to worry about trying to maneuver around everything,” says Carl Peters of Polar Mfg. The wall-mounted boom is free to swivel up to 180 degrees (optional brackets are available for up to 270 degrees). The welder hangs from a cable. To pull the boom out you just grab the welder and pull it to where you want it. By mounting the boom close to the shop door, it can be extended outside the shop for working on equipment parked just outside the door. Peters builds 3 sizes – 14, 20 and 28 ft. – and can custom-build other sizes as well. The 14-ft. model has a 2-stage boom and can retract to 8 ft. The 20-ft. and 28-ft. models have 3-stage booms and can retract to 8 ft. 8 in. and 12 ft., respectively.
“Since the boom sections are hollow, all welder leads and gas hoses can be tucked inside for a neat appearance. With your welder overhead, there’s no running into power cords or other items on the floor every time you move your welder.
“In a steel frame shop the boom attaches to a vertical column, such as a steel rafter. In a wood frame building, a separate column from floor to ceiling may need to be installed first,” says Peters “All the boom sections run on ball bearing rollers, which makes it easy to position the welder. You can also run power cords and air hoses through the boom sections.
“Another benefit is that your welder always stays cleaned up and out of the way, whether it’s in use or not.” The boom is designed primarily for 2-piece welders where the power source is separate from the wire feeder, says Peters.
“Most all-in-one welding units are too heavy for the boom. However, some all-in-one units can be used as the main power source and then all you need to do is add a remote wire feeder. That way you don’t have to upgrade the entire all-in-one welding unit.”
Brian Johnson turns steel cable into Damascus steel bars, bending and forging as many as 56 layers for strength and appearance. The steel bars, or “billets”, are used for making knife blades. He has also made a steel vise, anvil and a multitude of other tools out of the metal. To reshape the hard steel, he uses heating and forging furnaces that he built himself using a beer keg and a propane tank.
“My single burner forge furnace puts out more than 2,600°F," says Johnson. "The body is a 16-gal., stainless steel beer keg with castable refractory interior."
Making the flux-proof forging furnace was a more complex job. The easy part was cutting a hole for the fire chamber. The refractory cement had to be poured all at once.
"I cut one end off the beer keg and centered a cylinder for the fire chamber inside the keg," recalls Johnson. "Insulation anchors had to be welded inside the shell to anchor the refrac-tory material should it crack. I bought some anchors and made more, placing them every 6 in. on center. They give the refractory mud something to hold to while it cures."
Refractory material also had to be formed for the furnace mouth. An earlier furnace had a steel mouth, but it oxidized with heating and cooling. With this furnace, he made an outside form for the door and mouth with an inside square tube. Once the refractory cement was poured and cured, the form and the inside tube were cut away, and Johnson had a furnace with no interior steel to oxidize.
Johnson reattached the keg end, first fabricating 1/2-in. grooved rings in each edge. Using 3/8-in. thick, 1-in. bar stock, he made a steel ring to fit inside the two grooves for a tongue and grooved effect.
“I split the ring so it can expand and con-tract as the forge heats,” he says.
The forge sits on a 10-ga. steel cone with a shelf and door. The cone serves as both a base and storage for fluxes and other materials. Heavy-duty caster wheels provide mobility. Each wheel is mounted on a steel tube within a tube for easy height leveling.
He also fabricated a Venturi tube to feed the burner. He describes the Venturi as a tube within a tube that he slides back and forth to The 14-ft. boom sells for $1,790 plus S&H; the 20-ft. model for $2,990 plus S&H; and the 28-ft. model for $3,190 plus S&H. Contact: FARM SHOW Followup, Carl achieve the right mix of oxygen and fuel to the burner. Because he runs the propane at tank pressure, the flow of fuel pulls the air into the burner.
“I like a slightly fuel-rich flame,” he explains.
“If you have an oxygen-rich flame, you have more problems with oxidation.”
Johnson mounted a small electric fan at the end of the mouth. It blows a curtain of air across the handle of pieces being forged, keeping them cooler and easier to work with. It also disperses heat coming out of the forge, making it more comfortable to work around.
“The furnaces make it easy to work with metal, which I enjoy,” says Johnson.
“I make tools and Damascus knife billets, but not the knives. I let others do that.”
Contact: FARM SHOW Followup, Brian Johnson, 16777 County Rd. 751 N.W., Clear-water, Minn. 55320 (ph 320 558-6898).
Peters, Polar Mfg., P.O. Box 322, Taylor, B.C., V0C 2K0 Canada (ph 250 271-0554; [email protected]).
Anyone who spends a lot of time on a mechanic’s creeper working under semi trucks or large farm equipment will appreciate BatWing, made by Eidos Corporation in Lincoln, Neb. It’s the company’s lowest profile unit.
“A bad back costs a lot more than $600,” points out Stu Rafos, president of the company that has manufactured industrial grade ergonomic seating for more than 25 years. At $600, the BatWing is designed more for the consumer market than the company’s other 8 products, which are generally used on assembly lines at companies such as Boeing, Peterbilt Motors and Deere. All of Eidos’ products are designed to provide ideal body support to prevent fatigue and injury.
“Most of the products have to do with a particular application as far as height,” Rafos says. The BatWing is just 8 in. off the ground and perfect for working under ag equipment and large trucks.
“Basically it’s a modern day, ergonomic version of a mechanic’s creeper,” Rafos says.
“The back is controlled by a gas spring. The handle on the side is adjustable from zero to 90 degrees, and you don’t have to get off to adjust it. The molded foam cushioning is industrial grade.” Made of 12-ga. steel the BatWing is rated for more than 400 lbs. The back is controlled by a 600 to 800-lb. capacity spring. It rolls on ball-bearing castors, each with a 400-lb. capacity.
“Everything is over-engineered,” Rafos says.
“Less than 1 percent of our business volume is for service parts. They just don’t break.” The company’s other industrial grade products, made out of 12 and 14-ga. steel, range in price from $900 to $1,400. They are designed for specific tasks such as welding, bench work, and much more.
Contact: FARM SHOW Followup, Eidos Corporation, P.O. Box 29666, Lincoln, Neb. 68529 (ph 402 466-1119; www.eidosergonomics.com).
Brian Johnson’s steel vise is big enough for anything he can throw at it. Its jaws open 14 1/2 in., and the length of the wide-open vise is nearly 4 ft. The face of each jaw is 10 in. by 2 1/2 in.
“Making the vise was a combination of a good challenge and a display of my welding abilities,” admits Johnson.
“Besides, it’s fun to have something different from what others have.”
The starting point for his vise was plans published by the James F. Lincoln Arc Welding Foundation (www.jflf.org). Gordon Hen-nen, the author, described it as a rugged steel vise that “will not break or distort”. Johnson says the sliding tube design has lived up to Hennen’s promise.
“If I put something in the vise, it doesn’t come out, and it doesn’t turn,” he says.
“It’s not like the imported vises available today.”
Johnson modified his vise to make it bigger and stronger than Hennen’s original. His moving jaw mounts on 1/2-in. thick, rectangular steel tubing. Johnson’s crank is 1 3/8 in. in dia. with four threads to the inch (Acme).
The Hennen vise crank attached to the bottom of the fixed jaw. Johnson explains that that would allow flex and forward movement and possible binding. Johnson used a straight through draw bolt design that allows the most mechanical advantage possible and prevents binding.
“I salvaged chrome plated hydraulic shaft-ing for handles, handle knob and also for the draw bolt screw,” says Johnson.
“It’s high tensile and machines well.”
Another bit of luck went into the vise’s massive hammer block that sits behind the fixed jaw. Johnson found it at a local scrap yard. The piece is 2 1/2 in. thick and 4 in. wide at its narrowest end and a bit wider at the opposite end.
“All I had to do was bevel it a bit and weld it in place,” he says.
Johnson says the vise comes in handy when he makes forges. He designed a brake that fits in the vise for bending both treated and diamond 10-ga. steel plate.
Contact: FARM SHOW Followup, Brian Johnson, 16777 County Rd. 75 N.W., Clear-water, Minn. 55320 (ph 320 558-6898).
Brian Johnson can make a bashed up old anvil look like new. He also made a new anvil from scratch. An experienced blacksmith, Johnson knows how vital a smooth anvil surface is. He also knows how beat up most old anvils are and how poorly made many new anvils are. That’s why he made his own “giant” anvil and fixes up others.
“I made an 8-in. wide, 1,000-lb. anvil out of 1,237 lbs. of steel,” he says.
“The top and base are 4-in. thick steel plate, and the stem is 6-in. thick steel plate.”
The proof of a good anvil is how resilient the top is. Johnson says the way to test an anvil is to drop a ball bearing from about a foot above the surface. It should bounce back up into your hand. The resiliency is what makes a blacksmith’s hammer bounce back into the air when he strikes hot iron on the anvil.
Wrought iron anvil tops and bases are Johnson’s preference. Since wrought iron is no longer made, he settled for mild steel for the top, base and stem on his new anvil. To get the resilient top, he needed a final hard surface. Johnson applied two layers of Rockwell 62 hard facing, 6010 (super buildup) class rod or wire. The second layer was laid down perpendicular to the first, with each layer measuring from 5/32 to 3/16 of an inch thick.
He follows a similar procedure in repairing old anvils. Once he has ground out any rust in pits or cracks, Johnson uses penetrant dye to find fine cracks. He then grinds until no more die can be seen, indicating fresh metal.
In both his new and old anvils, Johnson heats the anvil to a surface temperature of around 400 degrees Farhenheit. This helps ensure an even weld. If the welding process is interrupted, he will reheat before resuming welding. Johnson also fills pritchel and hardy holes with pieces of carbon block to prevent weld deposit.
“Each pass overlaps the previous one,” he explains.
“If you lean the anvil away from you, the passes get thicker.”
Johnson uses bumper bars to either side of the welding path. These are copper plates that are clamped in place. This allows him to make a complete pass each time from one end to the other or side-to-side.
On old anvils, the first layer fills in cracks and holes.
“You need to lead the forward edge of the puddle into a vertical crack to be sure it fills in properly,” he advises.
As the second layer is finished, Johnson advises using a measuring tape to be sure the new surface is even from the base. He then uses a square to evaluate how level it is at the surface. If needed, more weld is added.
Again Johnson applies heat to the entire surface of the anvil as he finishes layering the weld.
“Oftentimes, the welding will leave one part of the surface hotter than other areas,” he explains.
Even cooling is as important as even heating, he adds.
“I will turn a smaller anvil over into a pile of barn lime to cool overnight,” he says.
“It’s a good insulator and slows the process. Larger anvils will get barn lime heaped over the top, and the entire anvil will then be wrapped in fiberglass insulation and left to cool slowly.”
Once two even layers are in place and evenly cooled, Johnson grinds them down. Initially he uses a grinding wheel on edge to take off the ridges. Once the surface is down to ripples not ridges, he begins a horizontal grinding pattern using a 6-in. cup wheel. He stops frequently to be sure he is maintaining an even, level top. Chalk rubbed on high spots make it easier to level.
“For the final finish, I use a lunchbox grinder with special disks,” says Johnson.
“I also chamfer out the pritchel and hardy holes to reduce the chance of chipping.”
Johnson also dresses up the edges of the anvil top. On some anvils he has reworked or rebuilt the horn, pritchel and hardy holes and even the base prior to adding the hard surface to the top.
While some anvils may be too far gone to repair, most can be renewed. The exception in Johnson’s mind is cast iron anvils.
“An old wrought iron anvil is my first preference, followed by mild steel,” he says.
“However, if it’s cast iron, it’s not worth anything.”
Contact: FARM SHOW Followup, Brian Johnson, 16777 County Rd. 751 N.W., Clear-water, Minn. 55320 (ph 320 558-6898).
Melvin Erskin got an old Oliver 1250 up and running with the aid of a scavenged Isuzu diesel engine and help from family and friends. The Oliver 1250 was originally equipped with a Fiat gas engine. When Erskin saw it at the implement dealership where he worked, the engine was shot. When he retired, he asked about it and his boss said to take it.
“I needed a tractor and flgured if I could flnd an engine, I could get it going again,” said Erskin.
“My son-in-law and a friend are machinists, and they told me if I found an engine, they would put it in.”
A trucker friend gave Erskin an Isuzu diesel off a Thermo King refrigerated reefer. John Cornell, Erskin’s son-in-law, and his friend, Kevin Buck, went to work. In order to slip the Isuzu with its 24-qt. oil pan into the Oliver, changes had to be made. The bottom half of the oil pan was cut away to flt the frame of the tractor. With its reduced size, the pan still holds about 11 qts.
New motor mounts had to be made. The machining got more difflcult when it came to the bell housing. In order to match the new engine to the tractor’s bell housing, an adapter plate had to be fabricated. At the same time, the flywheel had to be cut down to flt the available space.
The engine was still two inches longer than the Fiat had been; so the three men cut the fan shroud down to flt it in. They also installed a hydraulic pump on front.
“The machining was so exact that we have never had to adjust the clutch since,” says Erskin.
“Without John and Kevin, I couldn’t have afforded to have it done.”
Contact: FARM SHOW Followup, Melvin Erskin, 2656 Dale Dr., Six Lakes, Mich. 48886 (ph 989 365-3398).
If you need a unique cast part for older equipment, talking to Gary Martin might be your best first step. He has made models for castings that range from 25 grams to 25 tons. His work varies from miniature parts for antique tractor collectors to man-sized steam engine flywheels.
“I’ve been a pattern maker for 35 years and can make a model for anything that needs to be cast,” says Martin.
“I’m kind of known as a steam engine expert. I have done work on parts for antique railroads for Disneyland, Knox Berry Farm and various amusement parks and individuals who own their own trains. However, I also do a lot of antique car work.”
In addition to making models or patterns for castings, Martin is the largest supplier of model engine flywheels in the world. He stocks more than 30 sizes from 3-in. to 22-in. dia. and has patterns for larger models and full-size engines. He also makes and sells machine tool kits and engine kits, including a 3/10 scale Deere 1 1/2 hp Model E gas engine. It’s priced at $895.
“I made the patterns for it and oversaw the castings of the kit,” explains Martin.
“Jerry Frisbie of Dinky Dears developed the castings, drawings and instructions. It’s a kit the first time machinist or father and son team can build.”
Martin has also made patterns for and markets kits and castings for a number of machining tools, including a Quorn Universal Tool & Cutter Grinder for sharpening lathe tools and other cutting tools.
A former industrial arts teacher, Martin fears that skills such as his are going to disappear. He teaches pattern making through a local college and privately to individuals in his own shop. Classes run for ten weeks and cost $300.
“My students are using their new skills to make antique car parts, wood plane and lathe parts, steam engines and other projects,” says Martin.
“Most classes meet once a week for ten weeks, but I am considering an intensive one week workshop if enough people are interested.”
Contact: FARM SHOW Followup, Martin Model & Pattern, P.O. Box 19792, Portland, Ore. 97280 (ph 503 329-8949: [email protected]; www.martinmodel.com).
“I discovered the Blue Cobra on YouTube a couple of years ago and realized it was a great product for our market,” says Rock Tyson, VP of sales and marketing for Ken-Tool, the world’s leading manufacturer of tire service hand tools. Invented by a company in Brazil, the Blue Cobra is an ergonomic designed tool to demount tires off semi-truck rims (22.5 and 24.5-in. dia. tires on wheels up to 13 in. wide).
“It works because of the combination of the patented shape of the head of the tool, and the leverage you get from the handle. A normal tire bar is 37 in. long. This tool is 54 in. long and gives you much more leverage,” Tyson says. Place the tire on the ground and break the bead. Insert the end of the Blue Cobra between the tire and wheel and rotate it over the top to pull the top bead off. Reverse the motion, put the handle down to your knees, which gets the tool to the bottom bead. Rotate over the top again and pull the tire off the rim. A video on Ken-Tool’s website demonstrates demounting four tires in about a minute. Made of powder-coated premium grade steel, the Blue Cobra will outlast brass and bronze competitors, Tyson says. The head has two industrial nylon rollers, which protect the rim and provide rolling fulcrum points to reduce user fatigue. The Blue Cobra is available for about $369 through auto part chains such as NAPA, O’Reilly and Car Quest. Contact: FARM SHOW Followup, Ken-Tool, 768 E. North St., Akron, Ohio 44305 (ph 855 821-7309; www.kentool.com).
Got a chainsaw that just won’t run right? Or a push mower that needs a tune up? If you’re not an expert at that kind of small engine work, you might want to check out a new “service school” online that walks members step-by-step through preventative maintenance and small engine diagnostics.
“We film professional mechanics who work on chainsaws and other small engine tools every day,” says Roger Simons, found-er, ATTN (Advanced Technical Training Network).
“They will walk through a repair scenario on all the things likely to be repaired through the life cycle of a product.”
The preventative maintenance section of the website – which costs members $9.95 a month – covers trimmers, edgers, commercial mowers, trailers and chainsaws. Chainsaw maintenance is broken into 13 segments, including Chainsaw Bar, Fuel Line, Oiler, Air Filter, Sprocket and Recoil. Overviews included “Clean, Inspect and Torque,” cov-ering basic tips such as not using excessive air pressure, especially on seals and gaskets.
Individual segments are easy to under-stand. Illustrations clearly define worn sprockets and other problems, using well-worn and damaged components. Even for an experienced chainsaw owner, the sessions offer a worthwhile refresher.
The diagnostics section covers identifying problems with both two-stroke and four-stroke engines. It uses “first glance” evalu-ations to identify generally what a problem might be. Related documents offer specific diagnostic steps for problems such as no spark, compression or fuel delivery.
“Our goal is to show people who want to do their own maintenance or diagnostics how to do it,” says Simons.
“If repairs are needed, they may well decide to take it to the repair shop. However, now they’ll understand the problem or its complexity and feel better about paying for the repair.
“If you understand the maintenance that needs to be done, you are more likely to notice if you can access this or that part eas-ily,” says Simons.
“Something as simple as draining oil is important. Do you want to have to turn the motor on its side to drain oil out of the refill hole or do you want an engine with a drain plug?”
Simons understands how important the simple things are when it comes to maintenance. His background includes starting a technical training program for Stihl chain-saws in the U.S. He then did the same for Husqvarna and also supervised their call center.
“After years of talking to end users, there were a lot of simple things that people wanted to do, but didn’t know how to do,” he says.
“We have the mechanic describe what he is doing as he does it. An important tip can be as simple as avoiding screw failure by cleaning out the slot first so you don’t strip it.”
Contact: FARM SHOW Followup, Ad-vanced Technical Training Network, ([email protected]; www.advancedttn.com).