Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 24, No. 2 (2000)

Vol. 24, No. 2 (2000)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 38–40

37 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Charles Larson

Charles Larson, Kalispell, Mont.

“Here’s how I solve the problem of air leaking out around the rims of tubeless tires. Just put some crankcase oil in the tire and it will seal right up. Works great.”

From the archive · Full text
Reader shop tip

Edwin H. Veitengruber

Edwin H. Veitengruber, Frankenmuth, Mich.

“Here’s how to break the bead on any tire. Just lay it on a concrete floor and drive your tractor or pickup over the edge of the tire. I have done this many times and it’ll break even the most stubborn tire. If it’s a large tire, you can lay down a board ramp up to the tire.”

From the archive · Full text
Reader shop tip 1 of 2

Richard Cox

Individual tip 1 of 2 from this reader’s published contribution.
Richard Cox, Jacksonville, Ill.

Richard and friend, Buddy White, Jacksonville, Ill., made this shop hoist from parts salvaged from an old portable elevator and a wagon hoist.

A hand-cranked winch mounts on the side of the hoist and runs up through pulleys on top. The lift rolls back and forth across the top of the hoist.

The winch came off a Little Giant elevator. The gantry mounts on casters, and travels anywhere it’s needed in the shop.

From the archive · Full text
Reader shop tip 2 of 2

Richard Cox

Individual tip 2 of 2 from this reader’s published contribution.
Richard Cox, Jacksonville, Ill.

The two men also came up with a handy high-speed sander-buffer for polishing steel shafts and also for rounding wood. It’s a high-speed emery blade mounted on an electric motor, mounted parallel to a small work table. They say it works as well on wood as metal because it doesn’t “fill” with gunk as it’s used.

From the archive · Full text
Reader shop tip

Lloyd Meffert

Lloyd Meffert, Rettick, Ill.

He put together a portable standby generator that mounts on the frame of a junked garden tractor. The tractor motor powers the generator via an electric-operated clutch-type pulley. The generator is a 5,000-watt Generac.

He made the frame towable with a hitch point on what had been the back of the tractor. He welded the front axle solid. An electric control box on the tractor activates the electric clutch to engage the generator.

From the archive · Full text
Reader shop tip

Alfred Amm

Alfred Amm, Michigan City, Ind.

“To make a hole with threads in sheet metal panels, burn a larger hole than needed and weld in a nut. Use a bolt to hold the nut in place while welding.”

From the archive · Full text
Reader shop tip

Weaver’s Welding & Casting

Weaver’s Welding & Casting, Corbin, Ky. (ph 606 523-4395)

“I run a small welding shop and a neighbor brought in a tie rod end from his MF 50 backhoe. The “ball” had popped out of its socket from wear. I cut a piece of 2-in. bar stock and chucked it into my old South Bend lathe and turned out a new socket “cap”, contouring the inner edge to match the ball. I then cut the old crimped cap part off the end and mig-welded mine on in place.

“I did the first rod end two years ago and recently did the other one. They’re working great, especially since I tapped grease zerks into the ends. The MF dealer wanted $400 per new tie rod end. I charged $70 for the two repairs.”

From the archive · Full text
Reader shop tip

Bruce Burns

Bruce Burns, 0935N 1100 E., LaGrange, Ind. 46761 (ph 219 367-2455)

“I built these steps in less than 2 hours on my 3010 Deere. I’ve been crawling on and off 10 and 20 Series tractors since they were new. This step is a great improvement, especially getting off. Wish I’d thought of it 35 years ago.

“What I did was to remove both existing steps. Then I took a piece of 2 by 2 by 7-in. steel tubing and drilled holes in it to match the holes where the steps were mounted. Next, I take a piece of 1/2-in. thick strap iron, 22 in. long by 2 in. wide, and make a bend at 12 in. Weld the piece of steel tubing to the back side of the L-shaped strap iron, about 5 in. from the top. Finally, turn the existing Deere steps upside down and weld them to the top and bottom of the ‘L’. And then bolt the whole assembly to the tractor.”

From the archive · Full text
Reader shop tip

Gordon Lawson

Gordon Lawson, Houston, Texas

“We saved a lot of money using a 2-ton engine hoist to set 18-in. dia. sections of concrete pipe which weighed 700 lbs. each. We used a come-along to draw the pipes together. It was so easy, my wife was able to operate the come-along while I pushed the pipe to its final position.”

From the archive · Full text
Reader shop tip

Richard Jaescke

Richard Jaescke, Northampton, Mass.

“My New Holland 565 twine tie arms came from the factory too rough. The knots were okay but the string would often get cut. I solved the problem by filing excess casting off until they were smooth. Works great now.”

From the archive · Full text
Reader shop tip

Paul Gilster

Paul Gilster, Bangor, Wis.

“Here’s a money-saving repair that saved me some money. It involved my 1984 Gleaner M3. The tube under the feederhouse that locks the head to the combine was rusted and bent. A new one was $130. I went to the local hardware store and bought a piece of 1-in. pipe the same length with threads and caps to screw over the ends. I took the insides out of the old tube and put in the new pipe, and drilled holes in the caps for the ends to come out. It works better than new and I’ve got just $8 invested.”

From the archive · Full text
Reader shop tip 1 of 2

Mike Ruppert

Individual tip 1 of 2 from this reader’s published contribution.
Mike Ruppert, Wapakoneta, Ohio

“For the times when I need an air compressor in the field, I put a valve and male air hose adaptor in the air tank on my grain truck. This gives me a portable air compressor.

From the archive · Full text
Reader shop tip 2 of 2

Mike Ruppert

Individual tip 2 of 2 from this reader’s published contribution.
Mike Ruppert, Wapakoneta, Ohio

“An idea I had in my shop was hanging some old school lockers on the wall, horizontally, three-high. They’re excellent for power tools, cords, and other miscellaneous equipment or parts.”

From the archive · Full text
Reader shop tip

Toby Truex

Toby Truex, Warrensburg, Mo.

“I have a 4-ft. tractor mower. The bottom gearbox seal was bad and needed to be replaced. I tried two gear pullers that didn’t work so I heated the hub and put in melted wax. The wax ran through the hub and out of the splines. Then I put the gear puller back on and the gear came off on the first try.”

From the archive · Full text
Reader shop tip

John Hill

John Hill, Millington, Md

“If you have a pit, or a hoist, for draining oil in your shop, put a 55 gal. drum on a set of caster wheels. Cut another 55 gal. drum in half and thread a 2-in. nipple into it. Turn it upside down into the drum on wheels. Works like a big funnel.”

From the archive · Full text
Reader shop tip

Tim Gest

Tim Gest, Grafton, Ohio

“The spring clutch on our Case 970 tractor broke and we couldn’t get enough leverage to attach it. So to make the spring longer, we inserted a washer on both sides. That gave us enough extra length so we could pop the spring into place. To remove the washers, we just pushed down on the clutch and they fell out.”

From the archive · Full text
Reader shop tip

LeRoy C. Mack

LeRoy C. Mack, Manistique, Mich.

“When a tie rod end came apart on our Ford 7000 tractor, I found that the nylon bushing was shot. A new end would have cost $60. I cleaned everything out and replaced the O-ring with a loop of #6 copper wire. Then I reinserted the ball, set the unit level, and poured in liquid lead babitt. When it started to cool, I just tapped the end to free the ball and then drilled in a hole for a grease fitting. This fix has worked very well.”

From the archive · Full text
Reader shop tip

Art Skoog

Art Skoog, Eagle River, Alaska

“The traction clutch had been sticking on my ’93 Deere 5300 tractor, which I bought new. It has MFWD with a loader, low hours, and does only light duty. It’s always shedded.

The problem was it would stay in gear with the pedal pushed. The clutch would disengage as soon as I touched the brake. I adjusted the free travel, moved the seat closer, and checked the pedal for obstructions. I couldn’t spot the problem so I guessed that maybe the clutch springs weren’t able to slide the clutch plates apart on the shaft. It might be binding on the spline. Another possibility was that popping the clutch could put a slight twist on the splines.

“The pto shaft runs inside of the hollow traction shaft on this tractor. I bought a mirror and was able to peer into the clutch housing from the top. I couldn’t get light in there with even the smallest flashlight so I got the idea of lowering a single Christmas tree bulb into the inspection hole. Then I could clearly see the driveshaft splines. I pushed in the clutch and saw the splines get covered with about 1/4-in. of movement.

“So I slid a small clear tube into the hole right up to the spline and sprayed in a bit of WD40. I could see it hit the target. I jacked up one tire, turned the shaft, and sprayed again. No more sticking for the past month since I did that.

“The Deere mechanic I talked to had wanted to split the tractor apart to access the clutch.”

From the archive · Full text
Reader shop tip

Larry Miller

Larry Miller, Spencer, Wis.

“I bought a Delta 14-in. chop saw which lasted less than 2 years before the motor burned out. I then rebuilt the saw at about 3/4 the cost of new only to have it burn out again 2 years later. At that point I decided to build my own. I built a frame and had a machine shop make a 1 1/4-in. arbor shaft for me. I had the bearings, 3 hp. motor, and switch. I used the vise and blade holder from the old chop saw. It’s well-balanced and with plenty of power to cut through 1/2 by 3-in. steel bar faster lying flat than the old saw did with metal lying on edge. I use standard blades. No problems at all after 3 years. It runs at 3250 rpm’s. The drive pulley is 6 5/8 in. dia. The driven pulley is 3 1/2 in. dia.”

From the archive · Full text
Reader shop tip

Tyler Plocinski

Tyler Plocinski, Williamsport, Penn.

“I repair garden tractors and the best idea I’ve come up with lately is using plastic quart oil bottles to change oil. I cut a square hole out of the wide side of it. The work great to catch oil from the engines. They fit into tight spaces. Once one is full of oil, you can use the original spout to pour it out.”

From the archive · Full text
Reader shop tip

Chris Lynch

Chris Lynch, Sabina, Ohio

“When we poured our shop floor we installed four 4-in. well casings in the ground and welded 18-in. long chains in the bottom. We placed them in the floor on 8-ft. centers so we can use them to hold equipment for repair.”

From the archive · Full text
Reader shop tip

O. Douglas Holland

O. Douglas Holland, Bedford, Va.

He came up with a method that makes it easy to install sleeves in a Massey Ferguson Perkins diesel. He freezes the sleeves to shrink them and heats the block with a space heater to the point where it’s too hot to the touch. Then he just presses the sleeves in.

From the archive · Full text
Reader shop tip

Thomas F. Jackson, Jr.

Thomas F. Jackson, Jr., Bowling Green, S.C.

Thomas tried an idea that has been in FARM SHOW before and says it really works.

“To remove a bearing race that’s in a recessed or hard-to-reach place, just weld a short bead onto the race. The heat and drawing effect of the weld will make removal easy.”

From the archive · Full text
Reader shop tip

Charles Huegel

Charles Huegel, Venus, Penn.

“My 1977 Belarus 400 tractor didn’t turn very sharp so I cut a 1 1/4-in. section out of each spindle arm. Then I welded the arms back together. This really quickened the steering and sharpened the turning radius. I’m sure the idea would work on other tractors.”

From the archive · Full text
Reader shop tip

John Meyer

John Meyer, Walton, N.Y.

“We had a problem hauling manure in winter to the top of hills. So we attached a bumper to the back of our Deere flail-type spreader. Metal brackets were welded on and a hardwood 2 by 6 plank attached. Then we put a metal pusher with an old tire attached on front of another tractor that we used to push from behind. Worked well.”

From the archive · Full text
Reader shop tip

Tom Macy

Tom Macy, Spencer, Ind.

“I stopped a 3-pt. leak on my Deere 3020 tractor by not letting it down when parking it. Just remember to push the lever down again before starting.”

From the archive · Full text
Reader shop tip

Colin Collins

Colin Collins, Myrtle, Miss.

“The Powershift on older Deere tractors with cables can be hard to shift. I clamped a rubber hose onto the cable cover, and clamped a grease zerk into the other end of the hose. Then I pumped grease through the length of the cable. The tractor now shifts like new. One cable was full of dirt and dry grease. To clean it before greasing, I clamped a tire valve stem into the hose after first filling the hose with parts cleaning fluid. Then I blew in air to clean the cable by forcing the fluid through. This repair works best if you work from the lower end of the cables at the transmission where it’s easiest to detach the cables.”

From the archive · Full text
Reader shop tip

Perry Hathaway

Perry Hathaway, Claypool, Ind.

“To hook a battery charger up to a 600 Bobcat, I put an extension onto the positive cable so I don’t have to take the seat off to charge it.”

Shop feature stories

From the archive · Full text
Feature story

Low-Cost Filter Keeps Shop Air Cleaner

Featured source:

“I was tired of breathing dirty air,” says Arvin De Cook, Sully, Iowa, who came up with an idea for a low-cost air cleaner to remove dust, smoke, paint and other airborne particles.

“During the winter, I spend many hours a day doing repairs in my heated farm shop. After a couple hours of cutting, grinding, welding or spray painting, the air becomes quite dirty. Usually you don’t realize it until you blow your nose. This air can do permanent damage to your lungs.

“You can run an exhaust fan but it’ll bring cold air into the shop, which gets costly. And few farmers can justify spending hundreds, or thousands, of dollars for a commercial air cleaner.

“I came up with this idea for a low-cost air cleaner that you can put together for less than $30. It consists of a 3-speed box fan which pulls air through four cheap furnace filters. The fan and filters are mounted in a plywood box which hangs from the ceiling in the shop. The fan also circulates warm air through the shop.

“The four plywood sides of the box screw together. A slot is cut out of one side for the filters to fit into. Then a cover is screwed over the slot to cover it. A piece of window screening goes over the open filter side of the box. The fan bolts into the other end of the box and pulls air through the filters.

“Maintenance depends on how much it’s used and how dirty the air is. The filters generally cost less than $1 apiece to replace. Because the fan pulls air through the filters, it’s always running on filtered air. However, when you need to replace it these fans can be bought for about $15.”

Contact: FARM SHOW Followup, Arvin De Cook, 9658 Hwy F 62 E, Sully, Iowa 50251 (ph 515 594-3438).

From the archive · Full text
Feature story

Ultra-Wide Baler Belts Eliminate Plugging Problems, Save Leaves

Featured source:

If you own a belt-type round baler, you’ll want to take a look at what Manitoba farmer Jake Wiebe has been doing to his baler.

Wiebe called FARM SHOW one day to tell us about the idea he came up with for his New Idea soft center 484 baler.

“A couple 4-in. wide belts went bad. I replaced the two belts with a single 10-in. wide belt. I had to take out the divider between the two belts. It worked so well I decided I might as well go wider. I just replaced all the belts with a single 5-ft. wide strip of rubber belting.

“My dealer looked at me funny when I told him I wanted a 5-ft. wide baler belt. But after he thought about it, he said he figured it just might work.”

The belting Wiebe used is the same material as regular belts are made of. The material is made in wide strips and then cut to size for each particular baler. You just have to request full-width strips.

He installed the wide belts himself using regular lacing on the ends. The only modification he had to make to the baler was to take off the spacers that go between the belts.

“Hay no longer can get stuck between the belts and I’m loosing less leaves out of the baler. It seems to run smoother and the repair was quick and easy to make,” says Wiebe.

His New Idea baler has several sections of belt. He is gradually replacing each section as they go bad. He’s looked at other belt-type balers and says he sees no reason why the idea shouldn’t work on them, too. He says the wide belts were no more difficult to handle and he feels the wide belt is stronger and should last longer than individual belts.

If you decide to try it, Wiebe suggests you shop around for belting. He got widely different prices from different dealers.

Contact: FARM SHOW Followup, Jake Wiebe, RR1, Winnipogis, Manitoba R0C 2G0 Canada (ph 204 656-4468).

From the archive · Full text
Feature story

Power Take-Off Remover

Featured source:

You can waste hours taking off pto shafts, bearings, sprockets and other similar equipment if you don’t have the right tools. And sometimes you have to resort to using a cutting torch, or you have to take the equipment to a machine shop in town to get the job done.

That’s what prompted Bruce Wilson to come up with his new “Pto Remover”.

It consists of two forks that slip around the pto shaft, or whatever else you’re trying to remove. The fork “tines” are angled so they fit together and don’t allow for any slippage. They tighten like a C-clamp so they come together from opposite sides and apply equal pressure to get the job done.

“I’ve used this tool on pto’s, sprockets, bearings – even tie rods on cars and tractors. I had a machine shop make them in different sizes, from 1/4 in. to 8 in. so there are many possibilities for use, all over the farm,” says Wilson.

He’s in the process of patenting the new tool and plans to bring them to market.

Contact: FARM SHOW Followup, Bruce Wilson, 1739 Back Grove Rd., Webster City, Ia. 50595 (ph 515 543-5211).

From the archive · Full text
Feature story

Low-Profile, Portable “Oil Changer”

Featured source:

After he built a new shop, Scott Smith, Blue Earth, Minn., didn’t want the mess that comes with changing oil and catching it in buckets or trays. So he built a low-profile, portable “oil changer” that drains away used oil and also disposes of it using compressed air.

He used heavy, 3/16-in. thick steel plate to make a 16-gal. tank, adding caster wheels to each end. A 6-ft. long, 2-in. dia. pipe extends out one end of the tank. A drain pan equipped with a quick-tach adapter fits into an elbow at the end of the pipe.

When changing oil, Smith rolls the tank under the vehicle and pulls the drain plug to drain oil into the pan. After the oil drains into the tank, the pan is removed and replaced by a pressure regulator, also on a quick-tach fitting.

He then rolls the tank over to an air compressor, stands the tank up on end, and hooks a hose to a fitting on the regulator. The hose leads to a 300-gal. tank outside the building, where oil is picked up for recycling. The last step is to hook an air hose up to a fitting at the top of the tank. Air is forced through a tube that extends from the fitting almost down to the bottom of the tank. It takes only a few pounds of pressure to force the oil out of the tank.

Contact: FARM SHOW Followup, Scott Smith, 33080 50th St., Blue Earth, Minn. 56013 (ph 507 464-3390).

From the archive · Full text
Feature story

How To Make An Engine Last Longer

Featured source:

In a recent issue of FARM SHOW there was a brief mention about diesel engine cylinder liner corrosion. Engineer Kevin Johansen, Mound, Minn., contacted us with the following comments.

“I now work with big railroad maintenance equipment of 4,000 hp. and up, but I did a lot of farm mechanical work years ago. At that time, we knew almost every farm engine we tore down would have tapered wear in the cylinder. The widest, belled-out part of the cylinder is at the top. Wear decreases towards the bottom, resulting in the familiar taper to the cylinder. This taper was attributed to mechanical wearing due to the piston side forces. It was one of those folklore items that ‘everybody knows is true’.

“However, I noticed that the hardest-working engines, which should have had the most wear, seemed to have the least taper. The bores might have more overall wear, but the wear was more uniform with little tapering. Those with the most severe tapering were the chore tractors – small loader tractors that got started and used every day, in all kinds of weather. Often for only a short time.

“The second clue to solving the problem is that the side forces of the piston are not at a maximum at the top, where the wear was the greatest, but further down the stroke. I ignored both these signs because of what I – and most other mechanics – knew to be true.

“Several years later, while doing research on diesel engines, I found an SAE research paper on cylinder corrosion during the cold startup of an engine. The essence of the paper was that byproducts of combustion can condense, form acids, and attack lubrication and the cylinder liners underneath. The acids are worse at the top of the cylinder since they are exposed to the wall the longest. There is a critical temperature range of between 100 and 160° F. Above and below that range, less damaging acids are formed.

“Bingo. Chore tractors are started up 365 times a year to get 300 hours on them. Big field tractors are started up 25 times a year to get the same 300 hrs. on them. So engine wear in the big tractors is more truly wear due to hard use. Wear in the smaller engines is more from corrosion and loss of lubrication.

“What this taught me is that getting longer engine life involves four simple, easy steps: “1. Maintain the cooling system, including fluid and pressure cap.

“2. Get the engine hot as soon as possible to get through those damaging temperatures. Keep the thermostats working. Cover the radiator with cardboard. Use block heaters or oil pan heaters. I have a stick-on oil pan heater wired together with a block heater on all vehicles. I plug them in at night and have a simple 24 hour timer that comes on an hour before I need the equipment the next day.

“3. Change oil frequently to get the acids and particulate out of the engine.

“4. Always question the ‘conventional wisdom’. Like someone said, ‘It’s not all the things I know that cause me problems, it’s the things I know that ain’t so.’” Contact: FARM SHOW Followup, Kevin Johansen, 2148 Basswood Lane, Mound, Minn. 55364.

From the archive · Full text
Feature story

Portable Lift Makes Small Equipment Work Easy

Featured source:

Here’s a handy new lift for anyone who does a lot of work on mowers or has thought about opening a sideline repair shop.

The Heftee 250 is a free-standing service lift that you can roll anywhere inside your shop. It’s designed to hold push mowers, chain saws, small engines, and other equipment. It’ll handle up to 250 lbs. The base of the unit rests on a U-shaped steel frame.

A pair of channeled lift arms mount on a rotating head that’s attached to a vertical steel mast. The arms can be adjusted from 16 to 42 in. wide. A pair of straps secure the equipment to the arms. You crank a handle to raise the arms up to 48 in. high. The arms can be rotated up to 360 degrees to provide optimum visibility and access to any part of the repair item. (There are 12 locking positions, one every 30 degrees).

“It works much like a free-standing forklift and requires no in-ground installation at all,” says Kelly Johnson, McCanse Engineering, Oregon, Ill.

“It eliminates the need to stoop down to the floor to make an adjustment or reposition the equipment on the floor or on the bench top. Separate brackets are required for chain saws, string trimmers, and small engines.”

Sells for $500 plus S&H. The company also offers two larger electro-hydraulic, push button-operated models that run on 110-volt electricity. The Heftee 2000 can safely lift 2,000 lbs. to any height up to 6 ft., and the Heftee 4000 can accommodate equipment up to 87 in. wide and safely lifts 4,000 lbs. They can be used to lift riding mowers, garden tractors, etc.

Contact: FARM SHOW Followup, McCanse Engineering, LLC, 107 South Daysville Road, Oregon, Ill. 61061 (ph 800 755-7540 or 815 732-7540; fax 2052; E-mail: [email protected]; Website: http://www.heftee.com)

From the archive · Full text
Feature story

Locking Jaw Adjustable Wrench

Featured source:

It looks like a cross between a vice grips and a crescent wrench.

Stanley’s new MaxGrip wrench has an adjustable jaw like a crescent wrench. You adjust to fit whatever nut or bolt you’re trying to loosen. Then squeeze the locking handle down to tighten the jaws, which have just enough “wiggle room” to clamp down tightly.

Sell for about $25 in stores. Contact: FARM SHOW Followup, Stanley Works, 1000 Stanley Dr., New Britain, CT 06053.

From the archive · Full text
Feature story

Hanging Tools In Shop

Featured source:

Here’s a simple way to store garden tools which we spotted in Countryside magazine. A dowel or broomstick is mounted horizontally along the wall. Loops of twine hang from the bar. To hang up shovels, hoes, pitchforks, etc., you make a “slip loop” over the end of the handle. The weight of the tool keeps the twine tight. When you need to use it, just lifting up on the tool releases loosens the twine.

Takes up much less room than hanging tools on nails.