Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 30, No. 4 (2006)

Vol. 30, No. 4 (2006)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 36–39

34 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Merton Russell

Merton Russell, Endeavor, Wis.

“I read with interest your article on high performance paddles for New Holland forage harvesters (Vol. 30, No. 1). The high performance paddles simply bolt on in place of the original ones. New Holland has had problems with the blower plugging up long before they came out with the 230 and 240 models referred to in the article. I own an 892 model and the rim sheets wore out on the back side.

“The problem isn’t with the paddles; it’s with the air design flow in the blower housing. I solved the problem by taking a rim sheet that had a hole in the back side and making a cut-off point that forces material to keep moving without plugging up. The tip clearance is just 1/8 to 1/4 inch.”

From the archive · Full text
Reader shop tip

Isaac Hopwood

Isaac Hopwood, Centre, Ala.

“Several years ago I did welding and mechanic work for a liquid fertilizer company. The company bought an extra truck and there was no room to install an air compressor on the motor. The truck needed a pto in order to operate the liquid fertilizer pump. To solve the problem, I built a bracket that mounts between the cab and the tank above the pto shaft, allowing the pto shaft to belt-drive the pump, since the liquid pump has to work at the same time as the air pump.

“I tapped into a pressure oil line on the truck’s engine and ran it back to the air compressor. Then I ran a return line back to the engine and tapped into the oil pan above the oil level. I also tapped into the water line to the compressor and engine with a pressure and return flow of water back to the engine.

“Because of dusty conditions, I ran a rubber hose from the compressor to up behind the seat of the truck cab to the compressor’s air filter. The truck needed an air compressor for two reasons: one, to open the air valve for the liquid fertilizer to flow from the tank and two, so that I could install a lock in and out for the pto on the transmission.

“I spring loaded the pto gearbox in the out position and used a small air cylinder from the shutters that close in front of a semi radiator to put the pto in gear, because I only needed it when putting out fertilizer.

“The truck was wrecked several years later and scrapped out. But it all worked fine for the years that I used it.”

From the archive · Full text
Reader shop tip

Precise Engine Repair

Precise Engine Repair, 151 Roberts Rd., Yakima, Wash. 98908; www.perr.com

This company offers the Vibratach, a tool designed to read the rpm’s on all engines and other rotating equipment.

You hold the unit against the engine housing while the engine is running and then turn the center dial until a vibrating wire reaches its maximum side-to-side movement. Then you read the dial to get your rpm’s. If the engine low idle or high idle is not in line with the engine manufacturer’s specifications, you can use the tool to make precise adjustments. Works with lawn mowers, go karts, electric motors, motorcycle engines - anything that creates rpm’s.

From the archive · Full text
Reader shop tip

3M’s Safety-Walk Tape

3M’s Safety-Walk Tape, www.3M.com

This self-adhesive roll of gray rubber comes in 60-ft. length rolls, in either 1 or 3-in. widths. It’s intended to add skid protection to a wide variety of surfaces. Works great on any slippery surface including stair steps, trailer fenders, pickup running boards, ramps, ladders, etc. Available in different make-ups. It can even be used on the back of cell phones to keep them from sliding around.

From the archive · Full text
Reader shop tip 1 of 2

Bernard Krieger

Individual tip 1 of 2 from this reader’s published contribution.
Bernard Krieger, Creelman, Sask.

“The air cleaner filter on my 1992 Case IH 1680 combine kept getting dirty. I had to change it as often as once every two days. New filters cost about $50 apiece so replacing them got quite expensive. To solve the problem I used a piece of 4 1/2-in. dia. pipe to extend the inlet pipe 2 ft. I unbolted the original air cleaner inlet pipe, then bolted the new pipe on in its place and clamped the original pipe on top of it. It made a big difference, because now the inlet pipe is up out of the dirt. Now I don’t have to change the filters nearly as often.

From the archive · Full text
Reader shop tip 2 of 2

Bernard Krieger

Individual tip 2 of 2 from this reader’s published contribution.
Bernard Krieger, Creelman, Sask.

“The hydraulic-operated table lift mechanism is a weak point on MacDon swathers, especially with the trend to more direct seeding on rougher fields. I have a 1992 30-ft. model and I didn’t want it to break, so I took preventative action. I made my own gussets and welded in some extra metal. It’s a good idea to do this before the table lift mechanism breaks, because if it ever does break it will be difficult to get everything all lined up again.”

From the archive · Full text
Reader shop tip

Terry Whitney

Terry Whitney, Delavan, Minn.

“I have a Case IH 863 corn head with leaky gearbox seals. A local repair shop told me to try using some Deere corn head gearbox grease. I added it to the regular gearbox oil, and it worked. The seals quit leaking.”

From the archive · Full text
Reader shop tip

Bob Moty

Bob Moty, Crystal Lake, Ill.

“I used 1/ 4-in. pegboard to make a tool board for use at home. To make box/open end wrench holders I cut off the heads on some 1/4 by 2-in. bolts, then bent 1/4 in. of the end of each bolt at a 90 degree angle and used ‘whiz nuts’ at the front and rear. Nuts and flat washers would also work. To make socket holders, I cut off 1/4 - 3/8-in. and 1/2-in. bolts and rounded the ends, then drilled holes in lengths of 1 1/4 by 1 1/4 by 1/8-in. thick angle iron and welded in the bolts. I like this system because all my tools are arranged by size and are always in full view.

“One side of the pegboard is for standard wrenches, and the other side is for metric.”

From the archive · Full text
Reader shop tip

James Burden

James Burden, Crystal River, Fla. (ph 352 794-0497)

“I bought some acreage next door last year that apparently had a lot of hidden metal debris on it. As a result it wasn’t long before I had three flat tires on my Deere L100 riding mower. To solve the problem, I bought a $10 magnet at Harbor Freight (www.harborfreightusa.com) and attached it to the back of the riding mower, about 1 in. off the ground. So far the magnet has picked up two full coffee cans of nails, screws, brads, staples, wires, paper clips, bottle caps, and brackets. At the same time, I put a stop leak product in the mower’s tires and haven’t lost any air since then.

“The magnet measures 4 by 8 in. and has a couple of mounting holes. To position the magnet as close to the ground as possible, I screwed a 2 by 4 to the top of the magnet and then wired the 2 by 4 to the back of the tractor.

“The magnet is rated at 250 lbs. The mower is equipped with a 42-in. deck and the magnet is only 8 in. long. However, its pull reaches out a few inches to either side so it won’t take too many passes before the magnet will have covered the entire yard.”

From the archive · Full text
Reader shop tip

Ray Whatley

Ray Whatley, Bastrop, Texas

“I had problems with flat tires on my Goodyear 20.8 by 38 DT 710 10-ply rear tractor tires. The problem was due mostly to driving over heavy corn and sorghum stalks. Sometimes I was getting three or four flat tires a day. I solved the problem by replacing them with 14-ply Firestone tires. They were expensive at about $1,600 apiece but in my opinion, they also ‘bite’ better than Goodyear tires. I don’t use anything but Firestones on my tractors.”

From the archive · Full text
Reader shop tip 1 of 2

John R. Johnson

Individual tip 1 of 2 from this reader’s published contribution.
John R. Johnson, Paradise, Mont.

“When a pulley on my pto-driven sicklebar mower froze onto the shaft, I used a liberal amount of Kroil lubricant to loosen it up (ph 800 311-3374; www.kanolabs.com). After applying the oil I let it set overnight. The next day, the pulley came right off.

“I use a lot of this product so I bought a 1-gal. jug. I also bought a small can for my wife who uses it all the time, too.

From the archive · Full text
Reader shop tip 2 of 2

John R. Johnson

Individual tip 2 of 2 from this reader’s published contribution.
John R. Johnson, Paradise, Mont.

“After the radiator on my tractor plugged up, causing the tractor to overheat, I decided to try to clean it out. I flushed the entire cooling system with a mixture of water and triso-dium phosphate, which removed all the goop and gunk. Then I dumped that mixture out of the radiator and flushed it again with a mix-ture of muric acid and water. It cleaned the entire system, and my total cost was only about $5. When I looked down into the radiator it was sparkly clean. No more problems..”

From the archive · Full text
Reader shop tip

Bob Bugger

Bob Bugger, Effingham, Ill.

“My home-built, portable metal table provides a good place to work on oily parts, without making a big mess. It has a concave top that slopes to one end of the table, where a built-in trough directs oil to a small hole at one corner of the table. From there, the oil drains through a metal pipe and into a bucket below the table.

The table is made from an old section of curved, 1/2-in. thick steel boiler plate on a heavy pipe frame and heavy caster wheels. It’ll handle just about anything I can lift onto it, including tractor engines, automatic transmissions, gearboxes, etc.

“I often use the table in my basement workshop, which is attached to my garage. I can drive a tractor into the garage, take the engine out, set it on the table, then roll the table on into the basement where I disasemble the engine and let the oil drain off.”

From the archive · Full text
Reader shop tip

Paul J. Dietz

Paul J. Dietz, Hicksville, Ohio

“I wanted more shelf space in my 30 by 30-ft. garage, without taking up more floor space. To solve the problem I bought some 4-ft. wide, 5-ft. high commercial plastic shelves and hung them from the ceiling joists along two walls. The top shelf is about 12 ft. off the floor. I use a pole with a hook on it to retrieve any objects that I can’t reach.”

From the archive · Full text
Reader shop tip

Robert Mork

Robert Mork, Sevierville, Tenn.

“A couple friends of mine own a small engine and mower repair business. Years ago, they got me to use Briggs & Stratton fuel stabilizer and said if I used it continually that I would never have carb problems with any of my equipment, even if it sat for extended periods of time. The current EPA mandated fuel blends have little shelf life and over time can wreak havoc on small carbs like mowers, chain saws, weed trimmers, and such. Over the past 5 or 6 years, though, I have had no problems with any of my engines starting or running even if they sat idle for up to 2 years.

“A 32-oz. bottle of Briggs & Stratton Fuel Stabilizer sells for $21.95 and will treat 80 gal. of gas. It has a built-in measuring cup. Small capsules that treat 2 1/2 gal. are available for $1.”

From the archive · Full text
Reader shop tip

John Johnson

John Johnson, Paradise, Mont.

“There’s no better product to free up rusted bolts, springs, and other parts than Kroil, a penetrating lubricant from Kano Labs (www.kanolabs.com; ph 800 311-3374 or 615 833-4860). It’s better than WD-40 by a long shot. I’m not a salesman for the product. I just want to tell people how great it works.”

From the archive · Full text
Reader shop tip

Darrel Harp Enterprises, Inc.

Darrel Harp Enterprises, Inc., P.O. Box 140, Red Bay, Ala. 35582 (ph 256-356- 4424; www.darrellharp.com)

This company is a good source of parts for import tractors, including Chinese, Japanese, Shenniu, Fengshou, Mitsubishi, and more. The company offers a water pump rebuilding service for Asian tractors and they also offer Asian tractors for sale, along with tillage, planting, and harvesting equipment.

From the archive · Full text
Reader shop tip

Rex Gogerty

Rex Gogerty, Hubbard, Iowa

Rex sent us this picture of a tool trailer set up by a local contracting company. He figured the same idea could be used by anyone to make an inexpensive farm shop. The contractor cut a side door and picture window into the side of a semi trailer. Inside are tool and parts storage, and an office area. Rex notes that used semi trailers can often be picked up at a low price.

From the archive · Full text
Reader shop tip

George Reisner

George Reisner, Jewett, Ill.

George says most lawn mower decks would need a lot less maintenance if they were washed out cleanly every time you mow. He came up with a practical, inexpensive way to flush the underside after he finishes mowing. He attached a pipe to a concrete wall and runs it out along the ground. He drilled holes every few inches that squirt upward. He just turns the water on and drives over the pipe with the mower running.

From the archive · Full text
Reader shop tip 1 of 2

Arco Rosenow

Individual tip 1 of 2 from this reader’s published contribution.
Arco Rosenow, Chillicothe, Ill.

“To keep wasps and spiders out of the hose connector on air tools, press on a 1-in. long, 1/2-in. dia. plastic pipe with an end cap. The cap will also protect the threads from being damaged.

From the archive · Full text
Reader shop tip 2 of 2

Arco Rosenow

Individual tip 2 of 2 from this reader’s published contribution.
Arco Rosenow, Chillicothe, Ill.

“To protect hack saw blades and files, put them inside a length of 3/4-in. dia. plastic pipe. You can also wrap several feet of duct tape around the pipe for a convenient way to carry the blades and files.”

Shop feature stories

From the archive · Full text
Feature story

Service Rack For Garden Tractors

Featured source: John Conway

“It puts everything up high enough that I can service it easily,” says John Conway, Wilmore, Ky., about the service rack he built to service and repair riding mowers and garden tractors.

The service rack is made from 2-in. steel tubing and channel iron. It consists of a 3-ft. wide, 6-ft. long rectangular frame mounted on four 26-in. high legs made out of 1 1/2 by 1/4-in. thick material. An expanded metal rack serves as the floor. A pair of 8-ft. long wooden ramps attach to one end and an 8-in. high metal bar acts as a “stop”.

Two small wheels at the rear allow Conway to roll the service rack into his shop or outside to work on things.

The unit is painted black to keep it from rusting.

“I collect and restore Cub Cadet lawn and garden tractors, and I also repair lawn mowers for other people in my spare time. My service rack eliminates the need to bend over and crawl on the ground to work on lawn tractors. Makes it easier to service lawn mowers and other equipment, and also to overhaul engines,” notes Conway.

Contact: FARM SHOW Followup, John T. Conway, 706 East Main St., Wilmore, Ky. 40390 (ph 859 858-3256).

From the archive · Full text
Feature story

Portable Sandblaster Made From Combine Grain Tank

Featured source: Bob Bugger

Bob Bugger, Effingham, Ill., made a sandblaster out of a salvaged combine grain tank. It’s big enough to hold large parts and mounts on caster wheels so it’s easy to move around.

He started with a tapered grain tank off an old IH pull-type combine. He cut out one side of the tank to make an access door. An air-powered blast gun hooks up to an air compressor. A siphon hose runs from the gun down into a bucket of sand. An old squirrel cage fan clears away dust during sandblasting. Lights inside the tank provide light.

Bugger cut a pair of holes into one side of the tank and lined them with plastic cut out of old 5-gal. buckets, then attached lengths of truck inner tubing to the plastic to keep sand from blowing up his sleeves. He mounted a big pipe on the bottom of the tank to pull sand out of the tank. Inside the tank is a big grate to hold parts, with screens below it for sifting out small pieces so they don’t get into the sand.

There’s a large glass window above the access doors, with metal screen mounted just inside it to keep sand from scratching the glass.

“It doesn’t look pretty but it works well. I used mostly salvage parts so my total cost was less than $25,” says Bugger.

“I restore cars and tractors for a hobby, and I used the grain tank because I wanted a sandblaster that was big enough to fit a whole car front fender into. Most of the time I use it on small parts, which is why I installed two access doors on front. It’s important to use a tank with a tapered bottom, because it will funnel all the sand to one place.

“Switches mounted outside the tank are used to control the lights, blower, and shop vac. I can run the tube from the blower out the window to blow dust outside or, if I don’t want to blow dust outside, I can hook up the shop vac to the blower. Electric plug-in oulets mounted on the tank allow me to operate other shop tools. To keep condensation out of the air lines, which might cause sand to plug them up, I mounted a quick-tach final water separator on one end of the line.”

Contact: FARM SHOW Followup, Bob Bugger, 8971 E. 1025th Ave., Effingham, Ill. 62401 (ph 217 536-6516).

From the archive · Full text
Feature story

“Shover” Is Hammer And Shovel

Featured source: Clint Dearden

“I invented what I call the ‘shover’ one day after I had to repair an electric pasture fence and the only tool I had in my pickup was my shovel,” says Clint Dearden, Scott City, Kansas.

He took an old shovel that was missing its handle and welded a short length of pipe over it.

Dearden fashioned a hammer out of pipe and drilled a matching hole through both the hammer handle and the extension pipe. A 1/ 4-in. clip pin holds the two tools together into an adult-sized shovel.

He painted the first shover fluorescent orange because he found an extra can of paint in the shop. Since then, he’s made a second one that he painted black.

“The shover is simply a time and frustration saver, especially for a 19-year-old who has far better things to do than repair a fence.”

Contact: FARM SHOW Followup, Clint Dearden, 7261 East Road 90, Scott City, Kansas 67871 (ph 620 872-2814; [email protected]).

From the archive · Full text
Feature story

“Tool Tube” Caddy

Featured source: Denton Mastre

Tools are always at your fingertips with this new portable tool organizer that works something like a big tube-shaped pegboard.

The Tool Tube is a 2-ft. dia., 6-ft. high round PVC stand that mounts on a steel tread plate platform, which rolls on three heavy duty caster wheels. A handle attaches to one side. Pegboard-type holes cover the tube’s entire surface, allowing you to snap in a variety of optional shelves, racks, and holders that are colored light blue, making them easy to see on the dark blue tube. Optional attachments include a screwdriver rack, socket rack, miscellaneous tool compartments, vise grip and channel lock holder, pencil or chalk holder, tape measure holder, square and tri-square holder, and tool shelf.

Long metal pegs can also be snapped into the holes, allowing you to store both SAE and metric box end wrenches. Decals that indicate the wrench size are located directly above the wrenches.

A towel holder and work light can be mounted on top of the unit, and shelves can be mounted inside for additional storage room. Four 110-volt electric power outlets can be mounted at the base of the unit to operate air or power tools.

“It holds an amazing variety of tools, and you always know exactly where they are. The unit can be adapted to match any set of tools,” says Denton Mastre.

The base unit sells for $485, and up to $100 worth of attachments are available.

Contact: FARM SHOW Followup, Dynamic Sales and Service, 343 Washington Ave., P.O. Box 544, Grant, Neb. 69140 (ph 308 352-4362; [email protected]).

From the archive · Full text
Feature story

Made-It-Myself Bead Breaker

Featured source: Ron Young

Ron Young made his own bead breaker several years ago to make it easier to work on the more than 100 tires on his farm’s cars, trucks, wagons, and farm implements.

It consists of a 42-in. long steel base plate that bolts to a 48-in. long 2 by 12 wooden plank. A 2 1/2-in. long upright has several holes drilled in it to adapt to different size tires. A 60-in. pry handle pins to the upright. A curved bead-breaking shank hangs down from under the handle. It pivots on a loose bolt so it can swing, adjusting to the location of the bead. An adjustable rim-holding plate rests on top of the bottom base plate. It’s just a plate that can be moved back and forth to secure the rim.

“It makes the job easy. I made it from scrap meal,” says Young.

Contact: FARM SHOW Followup, Ron Young, 6870 State Rd. 938, Eau Claire, Wis. 54701 (ph 715 834-0983).

From the archive · Full text
Feature story

Tractor Air Cleaner Helps Riding Mower

Featured source: Bob Bugger

The 18 hp engine on Bob Bugger’s White FR18C riding mower is running on cleaner air since he added an oil bath air cleaner off an old late 1940’s Massey Harris tractor.

The Effingham, Ill., farmer welded a clamp-style mount to hold the old cleaner and bolted it to one side of the mower frame. It lines up between the mower’s front and rear wheels.

“I bought the mower from my son-in-law, and when I got it the original engine had already been replaced,” says Bugger.

“After using the mower just once I knew why - the air cleaner was already dirty after one use. The air cleaner was mounted in an enclosed area and had a pre-cleaner passage which was sucking in dirty air and blowing it into the engine. The pre-cleaner was a good idea, but not when it’s enclosed like that because the engine had access only to dirty air.

“To solve the problem I had to block off the pre-cleaner passage without blocking the air flow to the engine.”

To do that he cut a hole into the side of the air cleaner housing and welded a length of exhaust pipe into it. Then he clamped a 12-in. length of flexible rubber hose onto the pipe, inserted it through a hole in one side of the mower’s frame, and fastened it to the outlet of the oil bath air cleaner that was mounted to an outside frame rail. To seal the top of the original air cleaner, he cut a vacuum hose lengthwise and slid it onto the edge of the top plate.

“I added the air cleaner five years ago. Without it, I’m pretty sure I’d have gone through an engine or two by now,” says Bugger.

“I’ve never had to change the air cleaner, and the oil stays cleaner so I don’t have to change it as often.”

Contact: FARM SHOW Followup, Bob Bugger, 8971 E. 1025th Ave., Effingham, Ill. 62401 (ph 217 536-6516; fax 217 347-5331).

From the archive · Full text
Feature story

Aerosol Paint Can “Shaker”

Featured source: Paul J. Dietz

Paul Dietz got tired of wearing out his arm while shaking aerosol paint cans.

“I thought there has to be a better way so I could do other jobs while the paint was being mixed.”

So he came up with an automatic “re-volver” that simply rotates the can around and around, causing the ball inside to roll back and forth. The device makes use of a windshield wiper motor and an ordinary car jack.

He started with a 2-speed wiper motor. He removed a metal arm that attaches to the wiper blades.

The aerosol can is strapped onto a metal cradle, which consists of a piece of sheet metal with the edges curled up. He drilled a hole into the cradle and threaded it, allowing him to mount the cradle directly on the wiper motor’s threaded shaft. The motor itself is welded to the top of an old bumper jack, which is clamped to the jack’s post.

To operate the shaker, he uses alligator clips to hook up the motor to a car battery.

“As soon as I feed power from the battery to the motor, the can starts revolving. It goes slowly around and around like the minute hand on a clock, causing the ball inside the can to start rolling back and forth,” notes Dietz.

Contact: FARM SHOW Followup, Paul J. Dietz, 8538 Lake Rd., Hicksville, Ohio 43526 (ph 419 542-7250).

From the archive · Full text
Feature story

Oven Range Hood Gets Rid Of Welder Fumes

Featured source: Bob Bugger

A salvaged oven range hood works great for exhausting welder fumes, says Bob Bugger, Effingham, Ill.

He bolted an old oven range hood to the wall of his basement to keep fumes from getting into his house, running ductwork from the hood out a basement window. To support the hood he made a wood frame hung from the floor joists, and uses it for storage.

“I do welding work closeby, and a lot of times I move my welding table under the hood and work there,” says Bugger.

“I had been using a fan to blow fumes out the door, or else I did my welding outside. The hood is nice because it has not only a fan but also a built-in light.”

Contact: FARM SHOW Followup, Bob Bugger, 8971 E. 1025th Ave., Effingham, Ill. 62401 (ph 217 536-6516).

From the archive · Full text
Feature story

Quick Fab Elbows Make Corners Easy

Featured source: Quick Fab

Putting right angles on steel and aluminum square tubing is a whole lot easier with cast steel and aluminum elbows from Quick Fab Products. The ready-made corners give you a strong joint without losing any structural strength. Just cut the square tubing to the length you want, set a matching elbow in place, and butt weld it tight.

“Jerry Miller is the fellow who came up with it,” says Eric Jeffreys, Miller’s partner in Quick Fab Products.

“He owned a machine shop for years and did a lot of work with tubing.”

Miller’s goal was to avoid the problems that occur with mitering tubes to get a square or near square corner.

Quick Fab Products now offers 10 steel elbows from 3/4 by 3/4 by 0.093-in. to 4 by 4 by 0.375-in. Aluminum elbows are available in 1 by 1 by 0.125-in., 1 1/2 by 1 1/2 by 0.125-in. and 2 by 2 by 0.125-in. Other sizes of both steel and aluminum can be made to order from 1/2 by 1/2 by 0.063-in. to 4 by 4 by 0.375-in. Prices vary by quantity and by size, ranging from a few dollars for a small elbow to nearly $50 (Canadian) for the 4 by 4-in. elbow. A 2 by 2 by 0.250-in. elbow has a suggested retail price of $9 (Canadian).

“Our elbows are 90 percent cast steel and aluminum tube,” explains Jeffries.

“They haven’t been heated to bend so there is no stretching or wrinkling and deforming of the inner curve. They have a full wall thickness throughout and are fully weldable.”

Miller says there are no tricks to using the elbows. Elbows with a wall thickness of 1/8-in. or more are made with a weld bevel, so they don’t have to be ground down before welding.

“Just figure the length to cut the tubing to give a specific size to whatever you are building,” he explains.

“A quick rule of thumb is that the inside radius of all the elbows is always 3/4 of the nominal dimension of the tubing. A 4 by 4 elbow has an inside radius of 3 in.”

Currently Quick Fab has a limited number of dealers in Canada, but is seeking more dealers in Canada and the United States, according to Jeffries. Elbows can be ordered by phone for delivery from the company or from a dealer listed on the company website.

Contact: FARM SHOW Followup, Quick Fab Products Ltd., 460 Hollywood Court, Kelowna, B.C., Canada V1X 7J1 (ph 250 868-3523; fax 250 862-3528; [email protected]; www.quickfab.ca).

From the archive · Full text
Feature story

Jack Lifts Riding Mowers

Featured source: MoJack

If you’ve ever had trouble changing blades or cleaning the deck on a riding mower, you’ll be interested in this new jack that’s designed to make the work a lot easier.

The Mo-Jack was invented by farmer Norman Krug (Vol. 29, No. 4) and, after some re-engineering, is now on the market. The patented unit works with a self-braking winch and strap and comes with jack stands for safety.

The self-braking winch lifts the mower on a T-shaped lift bar that supports the mower’s front wheels.

To use, just roll the front wheels onto the lift’s wheel pads and crank it up about 18 in. Place a pair of jack stands under the T-bar and insert a safety pin through a hole in the jack’s tower, then apply the parking brake on the mower. The large base frame provides solid support.

By removing the wheel pads from the T-bar, the unit can also be used to change a flat tire, using the T-bar to support either the front or rear end of the mower frame. Just crank the self-braking winch until the wheels clear the floor, then apply the parking brake or place wheel chucks behind the mower’s tires.

Three different sizes are available.

They all sell for $250.

Contact: FARM SHOW Followup, Mid-Kan Inc., 405 E. Albert Ave., Maize, Kansas 67101 (ph 316 722-6836; fax 316 722-9039; www.mid-kan.com).

From the archive · Full text
Feature story

He Makes His Own Square Tubing

Featured source: Duane Petterson

Duane Petterson needed to make four crosses out of stainless steel tubing to replace aging ones on the country church he attends.

“The lightest weight square tubing I could find in the size I needed was 11 gauge, which was too heavy,” says Petterson.

“I decided to use 18 ga. stainless sheet metal to make my own tubing. But instead of cutting the sheet metal into strips and welding them together, which would have created a lot of distortion, I decided to build a hydraulic shop press. It allowed me to bend all four sides of the sheet metal into square tubes and greatly reduced the amount of welding.”

The 24-in. wide press consists of a pair of 1 1/2-in. wide steel bars that form a bottom die. The distance between the bars can be adjusted by adding or subtracting spacers, which mount on a pair of threaded bolts that extend through both bars.

Two more horizontal threaded bolts, one on each side, are used to keep the dies in place. A pair of vertical threaded bolts, one on each side, serve as guides to keep the top punch perpendicular to the dies. Springs on the guides help return the punch when the hydraulic jack is released.

After marking where to bend the sheet metal, Petterson slip it under the punch and then presses the jack down until it makes contact with the sheet metal. The first bend leaves a 1/2-in. wide strip of metal, which serves as a lap joint that makes it easier to weld the seams together. The other bends are then made in the proper sequence until the square is closed up.

“This same shop press can be used on any project that requires multiple bends,” says Petterson.

“To bend thicker material I just open up the die spacing.”

Each cross has six metal cloverleafs on it. To make cutting the cloverleafs an easier job, he came up with a jig that works something like a protractor. The main body has three hinged tabs on it, with a hole near the end of the tab where he inserts the head on his plasma cutter. The main body is then clamped in place on the sheet metal. Small bolts form the hinge points, which the plasma torch pivots around.

“All the cloverleafs had to look the same, and this was the easiest way to make them all look alike. The circle radius always stays the same when using this simple tool,” notes Petterson.

Contact: FARM SHOW Followup, Duane Petterson, 5894 409th St., Rice, Minn. 56367 (ph 320 656-5279; [email protected]).

From the archive · Full text
Feature story

Used Chair Lift Makes Slick Shop Lift

Featured source: Albert Franzen

A converted stairway chair lift makes moving materials between floors in Albert Franzen’s barn easy. The lift, which he picked up cheap at a garage sale, required very little modification to use in the shop.

“I replaced the aluminum tracks with channel iron and rebuilt the chair mount over the traveling motor,” explains Franzen.

“We just bolted the track to the barn timbers. The cable is rated at 5,000 lbs. and the motor at 250 lbs. If the cable should snap, the emergency brake will hold the platform in place.”

Originally designed to run at a 45 degree angle on stairs, vertical placement required building a platform perpendicular to the uprights. He removed the seat and welded a metal framework above the lift motor with its rollers, reinforcing it and installing a plywood platform. Square tubing was welded to the platform frame to serve as a handhold and a place for a dead man switch to operate the lift. Control switches were also installed at the top and the bottom of the lift for those times when no one is riding the lift with cargo.

To get the most height out of the lift, Franzen mounted it so the platform can’t de-scend lower than about waist high. While this makes it more difficult to climb aboard, it makes it easier to load.

“It has been real handy to store shingles and such in the loft or bring them back down,” says Franzen.

“It is a handy way to get up and down from the loft, too. This year we even hung a deer from a hook on the under-side of the platform.”

Contact: FARM SHOW Followup, Albert Franzen, 17732 Scott Rd., Hinckley, Ill. 60520 (ph 815 286-7463; afranzen1 @msn.com).