Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 31, No. 5 (2007)

Vol. 31, No. 5 (2007)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 36–39

26 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Art Krenzel

Art Krenzel, Battle Ground, Wash.

“I use old socks to store ratchet tie-down straps in a toolbox in my pickup. The socks keep the tools from snagging on the straps and getting everything tangled up. I simply wrap the straps into a ball and slip them in the sock. It’s a cheap, quick and easy way to keep things neat.”

From the archive · Full text
Reader shop tip

Philip G. Lumley

Philip G. Lumley, Wilkesport, Ontario

“I had a 4-ft. long wood burning stove made for my shop, using a 24-in. dia. by 30-in. long, 1-in. thick pipe with a custom built 30 by 36-in. water jacket surrounding it. The water jacket holds 70 gal. of water that’s pumped water through pipes embedded in the shop’s floor. The stove sets in one wall of the shop and is filled from outside.

“Once I start burning wood in the stove it takes a while to warm up the shop floor. If I want, I can use a furnace fan mounted on the shop wall just above the stove to provide instant heat. A heat catcher box located just above the water jacket traps heat as smoke exits the flue. The fan blows across the heat catcher box.

“A small 2-in. dia. fan at the bottom of the wood chamber can be used whenever the stove is almost out to quickly restart the fire.

“Water inside the water jacket expands as it gets hot. A 20-gal. water tank in one corner of the shop’s ceiling is used to store the over-flow water.

“This system is very efficient and didn’t cost much to build.”

From the archive · Full text
Reader shop tip

Russell Mayes

Russell Mayes, Raymond, Ill.

Russell restores antique tractors and other farm equipment and needed a way to increase the lifting height of his A-frame hoist. His solution was to build two rectangular frames and weld them onto each side of the A-frame, adding a pair of caster wheels on each side. The frames added an extra 3 ft. of height.

From the archive · Full text
Reader shop tip

Speed Latch Systems

Speed Latch Systems, 101 E. Needmore Hwy., Grand Ledge, Mich. 48837 (RDelong.SpeedLatch@comcast; www.speedlatch.net/product.htm)

Their new Speed Latch pickup toolbox mounting system lets you secure a toolbox in the pickup bed without having to drill any holes in the bed rail. Uses the truck’s existing stake pockets. Requires no tools for installation, other than the drilling of two holes in the toolbox. It’s designed for all full-sized domestic brand pickups as well as the Ford Ranger and Toyota Tundra.

Comes in a kit that contains two cam lever assemblies, two flat washers, and two specially designed “U” nuts, which is all the hardware needed to mount one toolbox. You drill two holes in the toolbox, insert the assembly and spin on the nut, then flip the camlock lever to secure. Once secured, the latches are inaccessible and invisible from the pickup bed.

From the archive · Full text
Reader shop tip

Emory T. Skelton

Emory T. Skelton, McCalla, Alabama

He wanted a way to carry long objects behind his pickup, so he came up with a T-bar shaped extender that fits into the pickup’s receiver hitch. It’s made from sq. tubing and is bent up at an angle to keep the load level with the pickup bed.

From the archive · Full text
Reader shop tip

Vernon Hoffman

Vernon Hoffman, Phoenix, Arizona

“We were having trouble pinching the hydraulic hoses on our Case-IH disk. The hoses would get caught in the disk’s swivel-type drawbar whenever we made a turn, spraying oil all over everything.

“To solve the problem, we cut some 4-in. plastic drain tile into 12-in. lengths and ran the hoses through them in groups. The plastic tiles keep the hoses together so they don’t flop all over.”

From the archive · Full text
Reader shop tip

Weaver Majors

Weaver Majors, Little Rock, Ark.

“Breaking down tractor tires has always been a very labor intensive job. I use a Bobcat mini excavator to push the tire bead loose from the rim. It always works and I’ve never damaged a tire or rim.”

From the archive · Full text
Reader shop tip

Rick Lutt

Rick Lutt, Dallas, S. Dak.

“To finish planting in wet conditions or to go through occasional wet areas, I remove one of the gauge wheels from my Deere 7000 planter. Placing a bag of water softener salt in an empty herbicide or insecticide box adds extra downpressure for no-till.”

From the archive · Full text
Reader shop tip

Paul Martin

Paul Martin, Nashville, Tenn.

“I’ve learned to sharpen mower blades, shovels, pitchforks, and other miscellaneous tools using a relatively inexpensive handheld 4-in. angle grinder. To sharpen a blade, I secure the blade in a vise or clamp, then use the grinder to make equal swipes on each end to keep it balanced. You have to be careful not to grind too much on the bottom of the blade. Practice on an old set and after a while you’ll get the hang of it. Sharpening other tools just makes them easier to use. Commercial grinders sell for $50 to $60, but you can buy cheap Chinese knockoffs for $15.”

From the archive · Full text
Reader shop tip

Peter Bucci

Peter Bucci, Hebron, Ct.

“I use Amsoil/grease in all my equipment. I have mowers that I’ve used for 10 years without any engine or bearing problem. Good lubrication eliminates breakdowns. I swear by Amsoil grease and synthetic oils.”

From the archive · Full text
Reader shop tip

James Rissler

James Rissler, Hopkinsville, Ky.

“I’d like to warn your readers about the use of ethanol in gas engines. I have a small engine repair shop and see a lot of small engines ruined from the use of ethanol fuels. Chain saws and weed trimmer 2-cycle engines won’t run for very long on it. Ethanol is alcohol, and alcohol cuts oil so it doesn’t mix with the oil you add to the gas. Ethanol also cuts oil off the piston and cylinder, which will result in blown-up engines.”

From the archive · Full text
Reader shop tip

Chris Hardy

Chris Hardy, Miles City, Montana

“Storage of tools and supplies seems to always be an issue. The most wasted space is overhead. A 2 by 4 board with hooks rigged on a pulley system for storing extension cords on the ceiling has worked well for me. I use large overhead hooks for various other storage issues. A long stick with a hook on the end makes retrieving and replacing stored items an easy job.”

From the archive · Full text
Reader shop tip

Stephen Beck

Stephen Beck, Earlimart, Calif.

“I’ve made three major purchases of woodworking equipment from Grizzly Industrial and they’ve all been best buys (ph 800 523-4777; www.grizzly.com). Also, the machine tools I’ve bought from Enco are a best buy (ph 800 873-3626; www.use-enco.com). They have machine tools and accessories at some of the lowest prices I’ve ever seen. Both companies have excellent catalogs.”

From the archive · Full text
Reader shop tip

Ron Cook

Ron Cook, Hopedale, Mass.

Ron is a home inspector who sees a lot of interesting sights while looking over all kinds of property. He recently spotted this arrangement on a pair of garage doors. The owner apparently did not want to buy two garage door openers so he installed one in the center of the two doors and connected them together with strap iron and custom brackets bolted to the doors. It appeared to work just fine.

From the archive · Full text
Reader shop tip

Linda & Mark Petty

Linda & Mark Petty, Blackstock, Ont.

“In Vol. 30, No. 1, FARM SHOW featured our low-cost improved replacement part for the failed rod on the actuator used in Deere combines to adjust the concave. Since then, we have heard from farmers about another problem part. Farmers tell us the Warner Electric Linear Actuator for straw choppers on Deere rotary combines is a weak part that often fails. They were looking for a better replacement, rather than just putting in the identical replacement from Deere.

“We took apart a failed actuator and developed a new screw, nut and rod which exceed the strength and capacity of the original product for about 1/3 the replacement cost. The rod is stainless steel like the original but the wall thickness of rod is increased to improve strength. A bronze nut is securely attached to the rod. The replacement assembly for Deere Part #AH20992 can be purchased separately from the screw for $349 plus S&H. The screw sells for $129.

Contact: FARM SHOW Followup, Petty Machine & Manufacturing, 2850 Church St., Blackstock, Ont. L0B 1B0 Canada (ph 905 986-1521; www.pettymachine.ca).

Shop feature stories

From the archive · Full text
Feature story

Table Saw Tilts For Angle Cuts

Featured source: Dennis Hageman

When Dennis Hagen was a young carpenter, he needed a table saw for fine angle cuts. Since he couldn’t afford to buy one, he built one. Nearly 50 years later, the saw retains an honored place in the craftsman’s workshop. Hagen, now 80 years old, shared how he built the unique saw.

“My banker was getting a new desk, so when I told him about my table saw project he gave me his old oak desk. As a result, the table saw is made of fine oak.”

The saw stands 35 1/2 in. tall with a table that’s 38 in. sq. Instead of tilting the saw blade, Hagen came up with a tilting table design. The table tilts to the right of the operator, riding on curved arms fixed to the sides of the table. The arms, with arcs cut out of them, are supported on a long threaded rod that extends through the arcs and the legs on the right side of the table. The rod has a fixed plate at the far end and a wheel nut on the other end. When Hagen wishes to make an angle cut, he tilts the tabletop and then tightens the wheel down to secure the arms against the legs. For quick settings, Hagen has the arc supports notched at 30 degrees and 45 degrees.

Contact: FARM SHOW Followup, Dennis Hagen, Glaslyn, Sask., Canada S0M 0Y0 (ph 306 342-4927).

From the archive · Full text
Feature story

Load Lifter Helps Adjust ATV

Featured source: Marco Negri

If your ATV is bottoming out on the trail or under load, you may not need to spend hundreds of dollars on new suspension. Just install the $79.99 Pre-Gressor kit from tm2 Corp. on your front suspension forks. Once installed, you can quickly adjust it as needed to handle heavier loads.

The money-saving kit grew out of experience in off-road racing and working for a major ATV and snowmobile maker, says Mario Negri, one of the owners of tm2.

“We couldn’t imagine why all ATV’s didn’t have the ability to adjust shocks, especially as people add more and more equipment and carriers to their ATV’s,” explains Negri.

“We made a kit for Polaris first and now have adapted it to most major makes.”

He says some people are even adding the kit to ATV models that do come with a factory-installed adjustor.

“People tell us OEM adjustors are sometimes difficult to move or may malfunction,” says Negri.

“They just put ours on top of the one that’s there.”

Negri says most owners with moderate mechanical experience can handle installation. However, the degree of difficulty depends on the model and make. Some older models require more disassembly before the units can be installed on the front forks.

Negri says detailed instructions for installation are included for each model. An evalu-ator for a major ATV publication described the instructions as “precise” and reported no problems with installation.

The new product is the first of several to be introduced by the new company.

“We have a product for Polaris ATVs,” says Negri.

“Due to their independent rear suspension, they tend to squat. We have a product that, once installed, takes only 10 seconds to lock suspension.”

Contact: FARM SHOW Followup, tm2 Corporation, 6111 Hwy 10, Ste. 200, Ramsey, Minn. 55303 (ph 612 730-2336; [email protected]; ww.tm-2.com).

From the archive · Full text
Feature story

Stick-On Hydraulic Hose Protector

Featured source: Cofair Products, Inc.

You can eliminate “chafing” damage on hydraulic hoses by covering them with this heavy new adhesive wrap.

Tite Seal Hydraulic Hose Protector is a heavy duty, self-adhering neoprene material that forms a protective barrier against cuts and abrasions.

Unlike traditional spiral hose protectors that require a different size protector for each hose diameter, Hydraulic Hose Protector comes in one size that fits all hose sizes. The neoprene wrap still allows hoses to flex and bend, and it can be applied even after the hose has been installed. You can apply it to specific trouble spots rather than cover the entire length of the hose.

Available in 12 and 50-ft. kits. The 1 by 12-ft. kit sells for $28.95 plus S&H; the 50-ft. kit sells for $108.50 plus S&H.

Contact: FARM SHOW Followup, Cofair Products, Inc., 7301 N. St. Louis Ave., Skokie, Ill. 60076 (ph 847 333-6700; fax 847 626-4900; [email protected]; www.cofair.com).

From the archive · Full text
Feature story

“T-Handle” Socket Set

Featured source: David Novotny

By making use of some used deep well sockets he bought at a sale and some 3/8-in. steel rod and old rebar, David Novotny made a set of “T-handle” socket sets.

“At first I made just a couple of T-handle sockets and used them when working on lawn mowers and small engines. They worked so well that I decided to make a complete set.”

He welded the rod and rebar onto each socket to form a handle about 1 ft. long, with a 5-in. long cross “T” at one end. The shaft on one T-handle was made from a long 3/8-in. dia. bolt, with a drill chuck mounted onto one end of it.

“It works well for holding taps to clean out threads,” says David.

He also attached 13/16-in. and 3/4-in. deep well sockets onto the handles of a set of pliers “for working on the most common small engine spark plugs”. And he made a 3-way socket by welding three sockets together at the middle.

Contact: FARM SHOW Followup, David Novotny, 407 Ramona Ave., West Fargo, N. Dak. 58078 (ph 701 730-8627).

From the archive · Full text
Feature story

He Rebuilds Antique Magnetos, Carburetors

Featured source: Earl Lundin

If you collect or restore old tractors, you’ll be interested in the service offered by Earl Lundin of Revillo, S. Dak., who rebuilds magnetos and carburetors for antique tractors to “like new” condition. He even builds some of his own tools to do the work.

He charges $40 per hour and ships the re-built magnetos and carburetors by UPS.

“Rebuilding magnetos is a rare business and a lost art,” says Lundin.

“I don’t advertise and rely entirely on word of mouth. I do work for people from all over the U.S.”

A magneto is a self-contained, high voltage distributor that ignites the spark plug on older tractors that don’t have a battery. It produces a spark by running magnetic energy through a magnet, coil, condenser and points.

“A lot of antique tractors have been parked outside for 50 years or more so when I re-build the magnetos or carburetors, they’re usually all rusted up. I use a sandblaster to clean up the casting. When sandblasting I use only glass beads to keep from distorting the metal.

“I also install new threads on the bottom of Deere cast iron carburetors when condensation causes the threads to rust or break. Some of these carburetors have been on the tractor for more than 70 years. I make the threads on a turning lathe using my own jigs.

I also had to make my own jig for making the threads. As far as I know there are only two other people in the U.S. who make and install new threads like this.”

Lundin, who retired from farming in 1992, says he has been doing this kind of work all his life. He started doing it as a business 10 years ago.

Few people are willing to work on magnetos and carburetors found on antique tractors.

“Most mechanics avoid them, and no one has the tools,” says Lundin.

“In fact, a lot of antique tractors had battery ignition systems installed on them back in the 1950’s because no one knew how to restore the magnetos.

“I have all the tools required to repair magnetos and carburetors, including coil testers, condenser testers, spark testers, and a mag-netizer to charge magnets. I even had someone from Chandler, Arizona, make a digital gouse tester for me that measures how much magnetism is in a magneto’s magnet. It lets me know if I’m increasing the magneto’s magnetism level or if the magneto is already fully charged.”

He says he can rebuild any magneto, but often he has to make parts for them.

“I’ve even had to make my own pullers to take magnetos apart. For example, when I needed a puller for an International Harvester magneto and called the company, they said the last one they sold was way back in 1972. So I made my own, using a pattern from another mechanic who already had a puller.”

Lundin says the first magneto was built in about 1890 when gas engines first came out.

“I deal with the Wico Magneto Company in Chicago quite often to get parts.”

Most of the work he does is on Deere tractors, “because Deere customers have a ter-rific loyalty”.

During the winter months he conducts seminars in Arizona.

“I started up a breakfast club of tractor collectors. Every year I do one seminar on carburetors and another one on magnetos. Some people say I should start up a school, but I haven’t got that far yet,” he notes.

Contact: FARM SHOW Followup, Earl Lundin, 16485 486th Ave., Revillo, S. Dak. 57259 (ph 605 678-2694 or 605 880-0468 or 320 839-2920; [email protected]).

From the archive · Full text
Feature story

Boost Diesel Performance With Better Information

Featured source: Pete Dandekar

Monitoring the temperature of major components on diesel trucks is a great way to keep tabs on the condition of your vehicle. Of course that’s kind of hard to do with traditional OEM gauges installed. It’s especially questionable if you have added performance-enhancing equipment to your rig.

“For some reason, major car and truck makers have never been that into real pre-cise instrumentation,” says Jenn Dandekar, co-owner, Danin, Inc.

“Most drivers can get by, but if you really want to know at what temperature your engine is running, you need a pyrometer for exhaust temperature. Transmission fluid temperatures also give a more complete picture of operation. It’s especially helpful if you are pulling a load.”

Getting a better read on key temperatures and pressures is the goal of Danin’s new Optix series of diesel performance gauges. In the past, the company has offered a Pyro gauge as well as fuel pressure gauges and transmission temperature gauges. Now they have added gauges to monitor differential and coolant temperatures as well as engine oil pressure and rail pressure.

Dandekar says any of the gauges can be installed by their dealers or by a knowledgeable customer.

“We designed them to be easy to install with Molex connectors,” says Dandekar.

“You just run connections to the spots to be monitored.”

The gauges, complete with sensors and wire harness, are LED lit, tested, calibrated and ready to mount. Suggested retail prices range from $53 for the transmission temperature gauge to $198 for the Pyro gauge for monitoring exhaust temperatures.

Contact: FARM SHOW Followup, Danin, Inc., 3944 W. Segerstrom Ave., Santa Ana, Calif. 92704 (ph 714 662-0600; toll free 800 398-6580; fax 714 662 0607; www.danininc.com).

From the archive · Full text
Feature story

New Gauges For Old JD’s

Featured source: Jerry Trecka

Looking to replace a gauge for an old Deere tractor? That’s what Jerry Trcka needed when he contacted Travis Jorde, a specialist in Deere decals. When Trcka asked about gauge face decals, Jorde recognized an opportunity. Now Jorde makes the decals, and Trcka installs them in new and restored gauges.

“Jorde suggested we expand and do everything from 1935 to 1972 Deere 2-cylinders as well as the New Generation 20 and 30 series tractors,” says Trcka.

“All together, we do approximately 40 to 50 different gauge faces.”

Trcka restores some old gauges, but most of his business is making new gauges to fit the older tractors. Restorations can take 4 to 6 weeks and cost up to $60. Trcka takes apart the old gauge, cleans it, paints it and installs the correct face decal for the model. Gaskets, nuts, washers and glass lens (not plastic) are also replaced.

The bulk of his customers simply order a new gauge with the proper face. That process starts with a brand new gauge that Trcka disassembles. A Jorde decal is laid down to match the tractor model and year, and Trcka reassembles and calibrates the gauge. New oil and amp gauges are priced at $60 with a new temperature gauge priced at $70 to $80, depending on the length of the lead.

The key to either accurate restoration or replacement is matching the right colors and style to the model and year.

“Different years of the same model had different color combinations,” explains Trcka.

Contact: FARM SHOW Followup, Evergreen Restoration, W7619 Walnut Drive, Spooner, Wis. 54801 (ph 715 635-8629; [email protected]).

From the archive · Full text
Feature story

Truck Hoist Makes Good Shop Door Hoist

Featured source: Neil Thomson

For the past 20 years or so, 90-year-old Neil Thomson has been enjoying the use of a shop door hoist he made from a dump hoist taken off a 2 1/2-ton Ford grain truck.

He adapted it to open and close a 16 by 16-ft. shop door. The fully insulated shop is 24 by 36 ft.

“There’s a 2 1/2-ft. by 8-in. dia. hydraulic oil storage tank directly below the 4-ft. long ram. A 3/4 hp electric motor powers the hydraulic pump,” says Thomson.

The 4-ft. long ram is able to open the 16-ft. door because Thomson used cables and pulleys to quadruple its reach. He positioned two pulleys at the bottom, on each side of the ram, and two pulleys up by the ceiling. A steel cable runs through the pulleys and up over the ram. The end of the cable attaches to the door.

The insulated door consists of two 16 by 8-ft. sections (hinged horizontally across the middle with five homemade hinges). The end of the cable attaches to the door.

The door moves up and down in a track made from two pieces of 1 1/4-in. angle iron welded together, making it a 2 1/2 by 1 1/4-in. track on each side of the door that goes up and across the ceiling. Thomson used three roller bearings on each side.

“There are three little 1/8-in. jigs on each side, positioned in the last few inches where each roller stops when the door is fully closed. This forces the door tight against the framework of the wall.”

Between the set of tracks that sit on the shop ceiling, Thomson mounted two rods with adjustable, threaded ends. These rods ensure the track width stays constant.

“To lower the door, there’s a bleeder valve built right into the hoist that you open,” he says.

“It feeds the oil back into the reservoir from the ram. By adjusting the valve, you can adjust the speed of door movement in either direction.”

Thomson says he prefers the hydraulic system over an air system because “air has a bad habit of leaking out. Hydraulics will only leak extremely slowly,” he adds.

Thanks to the oversized door, Thomson can drive the biggest combine or dual 4-WD tractor into the shop.

Contact: FARM SHOW Followup, Neil Thomson, P. O. Box 1130, Eston, Sask., Canada S0L 1A0 (ph 306 962-3963).

From the archive · Full text
Feature story

He Repowers Tractors With Ford Flathead Car Engines

Featured source: Richard Lyman

“They draw a lot of attention at shows and parades,” says Richard Lyman, Mount Gilead, Ohio, about the Silver King and Oliver tractors he repowered with Ford flat-head V-8 car engines made from 1932 to 1953. The Silver King tractor was originally equipped with a Continental 4-cyl. 30 hp gas engine that was worn out. Lyman replaced it with a flathead 85 hp car engine that he painted blue. To make room for the new engine he cut the tractor frame and welded in some new material, lengthening the tractor by 10 in. The tractor came with 28-in. high rear wheels which “looked odd” after the tractor was stretched out, so he replaced them with 36-in. wheels. He also added a pair of homemade straight pipes, one on each side of the hood, that give the tractor a distinc-tive, rumbling sound.

“It really looks nice. The tractor’s main body is painted silver but I painted the motor blue and the wheel rims red,” says Lyman.

“It has a streamlined look. In fact, some people tell me it looks factory-built. You don’t even notice the tractor is too long unless a standard Silver King is parked alongside it.

“I made the conversion because I’ve always liked Henry Ford flathead engines and wanted to see if they would work in tractors. The Ford flathead has low compression and makes a sound that’s all by itself. Henry Ford engines are hard to come by - I got mine at a public sale and paid $200 for it.

“Everyone wants to know how fast it will go. I tell them that at my age speed isn’t a factor, but I expect it would probably go 50 to 60 mph. However, I only drive the tractor in second gear.”

Silver King tractors were made from 1934 to 1954.

“Most Silver King tractors were made in Plymouth, Ohio, and came with an engine that was part of the tractor’s frame. However, my Silver King was built in West Virginia. It had an engine that was separate from the tractor’s frame, which made it much easier to repower it. Only 78 Silver Kings were ever built in West Virginia, and I don’t know how many are still around.”

Lyman had to make an adapter plate to connect the clutch on the Ford engine to the tractor’s original bell housing.

“The flathead engine had two inlets and two outlets leading to the radiator, whereas the Silver King’s radiator had only one inlet and outlet, so I had to make two more inlets and outlets.”

The Oliver tractor was originally equipped with a 4-cyl., 18 hp engine which Lyman replaced with a Ford flathead 60 hp, V-8 engine. He didn’t have to lengthen the tractor, but he did have to downsize the gas tank, making it 2 in. narrower and 3 in. shorter, in order to make room for it. He also made a pair of straight pipes.

The tractor was originally started by cranking a lever. Lyman got tired of doing that, so he mounted a flywheel and pto shaft on back of the tractor as well as a starter. The system allows him to start the tractor from the rear instead of the front.

“To start the tractor I put the gearshift in neutral, engage the pto, and press the starter button. Then once the pto starts whirling, I let off on the clutch and shut off the pto, which disengages the starter so that it doesn’t have to run all the time,” says Lyman.

The new engine resulted in a gear reduction so the pto shaft wouldn’t turn over fast enough. To solve the problem he switched the tractor from 6-volt to 12-volt.

Contact: FARM SHOW Followup, Richard Lyman 4325 Co. Rd. 20, Mount Gilead, Ohio 43338 (ph 419 946-6932).

From the archive · Full text
Feature story

Air Filter Adapted To Fit Shop Vac

Featured source: Lowell Blakely

Old air filters from tractors and skid steer loaders can be used as “no-cost” replacement filters for shop vacs, says Lowell Blakely, Dunning, Neb. He removed the air filter from a Bobcat 642B skid loader and adapted it to fit his 20-year-old Sears shop vac.

“It saved the cost of a new filter. Also, it has a much more refined design so it does a better job of filtering out dirt and therefore reduces the amount of dust blowing around when I use the shop vac. It’s built for heavy duty use so it should last much longer than the shop vac’s original filter. Another advantage is that sometimes replacement filters for old shop vacs are no longer available,” says Blakely.

The replacement filter fits into the top part of the shop vac just like the original filter and extends down into the canister. It measures 5 in. in diameter and 1 ft. long - slightly longer than the shop vac filter but about the same width. To secure the replacement filter, Blakely used two 1/4-in. dia. metal rods to make a bracket and then drilled two 1/4-in. dia. holes into the top part of the shop vac. The rods are held on by two nuts at the bottom of the filter. Another bracket - a 1 1/2-in. wide metal plate - extends across the bottom of the air filter to hold it tightly in place.

Contact: FARM SHOW Followup, Lowell Blakely, P.O. Box 63, Dunning, Neb. 68833 (ph 308 538-2256).

From the archive · Full text
Feature story

100 Percent Veggie Oil Tractor

Featured source: Glenn Cauffman

While all tractor brands are approving some percentage of crop-based fuel in their engines, nobody is suggesting using 100 percent veggie oil. That hasn’t stopped Glenn Cauffman, manager of farms and facilities at Penn State University.

Three New Holland diesel tractors have been running for months on nothing but B100 made from soybean oil with zero petroleum content. Other tractors occasionally run on the pure veggie oil. The reason he’s using New Holland tractors is that it’s the only company that has approved the experiment and offered to back the warranty while Cauffman experiments.

“We have about 500 hours on each of the first two, and this spring we added a 150 hp New Holland T7040 with a Tier III emissions approved engine,” he reports.

“We have about 100 hours on it. We can’t detect any difference in power or fuel use between them and similar tractors on straight diesel fuel. We don’t see a power difference even when they are on the dynamometer.”

Cauffman credits high quality fuel for the results. They required the vendor to supply analysis of the biodiesel, proving that it meets industry standard ASTM6751. Cauffman says the vendor claims to be analyzing every tanker truck of fuel when it is delivered.

“The biggest concern of the industry is fuel quality,” says Cauffman.

“Fendt endorses the use of B100 in Europe, but not in this country. It all boils down to quality. There is no enforcement system of fuel quality in this country. We as customers have to insist on high quality fuel. The government will never do it for us.”

Contact: FARM SHOW Followup, Manager of Farms and Facilities, College of Agricultural Sciences, Farm Services, University Park, Penn. 16802 (ph 814 865-4433; [email protected]).