Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 21, No. 6 (1997)

Vol. 21, No. 6 (1997)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 30–31

28 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Roland Holder

Roland Holder, Hinton, Iowa

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

“I keep a few old wood splitting wedges on my welding bench to hold uneven pieces as I weld them together. They’re heavy enough to hold the parts in place and you can set up many angles. They’ll adapt to most any project.”

From the archive · Full text
Reader shop tip

Kirk Dahl

Kirk Dahl, Ruby Valley, Nev.

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

“I scratch the date, engine hours and oil weight on each oil filter that I replace when changing oil. At a glance I know when to change oil again.”

From the archive · Full text
Reader shop tip

Robert Slattery

Robert Slattery, Rudolph, Wis.

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

“When I bought a tractor with a cab on it, I could no longer reach the manual controls on my Deere 3940 chopper. To solve the problem, I mounted a small orbit motor on the shaft that turns the blower pipe and operate it with the hydraulic lever in the cab. To adjust the deflector hood on the blower pipe, I used a 12-volt electric car window motor. I ran a piece of clothesline from the window motor to the hood of the blower and wired a 2-way electric switch in the cab.”

From the archive · Full text
Reader shop tip

Donald L. Olson

Donald L. Olson, Saco, Mont.

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

“The power steering on my 706 International tractor quit working. I thought it was the hydraulic pump, which would have cost $490 to replace. But I found out there are not one but two filters in the hydraulic lines and one of them was plugged. I cleared it out and solved the problem.”

From the archive · Full text
Reader shop tip 1 of 2

Kevin McWilliams

Individual tip 1 of 2 from this reader’s published contribution.
Kevin McWilliams, Columbia, N.J.

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

“We changed out Deere 3020 over to 12-volt electric from 24-volt and used a Delco alternator to replace the original generator system, which never charged enough to keep the batteries fresh.

From the archive · Full text
Reader shop tip 2 of 2

Kevin McWilliams

Individual tip 2 of 2 from this reader’s published contribution.
Kevin McWilliams, Columbia, N.J.

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

“I made cheap TIG (heli-arc) wire for cast iron by sanding the old coating off some stickwire ni-rod. It had become wet and the coating was chipping off. It made perfect TIG wire, which I would otherwise have to buy for as much as $10 per pound.”

From the archive · Full text
Reader shop tip

Mark Bint

Mark Bint, Cysco, Tex.

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

“When a bolt head breaks off, I weld a flat washer to the bolt using a mig welder. Then I weld a large nut to the washer, let it cool, and 90 percent of the time I can just wrench the bolt right out.”

From the archive · Full text
Reader shop tip 1 of 2

Paul Rusch

Individual tip 1 of 2 from this reader’s published contribution.
Paul Rusch, Nekoosa, Wis.

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

“I save money on bearings by purchasing them at one of two local bearing distributors for at least half the dealer price.

From the archive · Full text
Reader shop tip 2 of 2

Paul Rusch

Individual tip 2 of 2 from this reader’s published contribution.
Paul Rusch, Nekoosa, Wis.

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

One tip on working with bearings: Heat expands and cold shrinks. Put a bearing in an oven at 200° to slide it on a shaft. Put it in the freezer to drop it into a bore.”

From the archive · Full text
Reader shop tip

Mel Naggatz

Mel Naggatz, Holyoke, Colo.

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

“I came up with a simple way to carry an emergency supply of air to the field. I made up a 8-ft. length of air hose with valve fittings on each end. If an implement tire gets low on air in the field I connect the hose to a tire in the back of my pickup and to the implement tire. Air is simply transferred from the pickup tire to the low tire.”

From the archive · Full text
Reader shop tip

S. Reppert

S. Reppert, Reading, Mich.

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

“I take a round chain saw file and cut a notch on a pencil. Then I take half of a clothespin, with the spring in place, and I slip it down to the notch. This gives you a pencil that you can clip to your pocket just like a clothespin. Works especially well with flat carpenter pencils.”

From the archive · Full text
Reader shop tip

John Adams

John Adams, Cross Plains, Texas

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

He had trouble with dirt and dust getting into the couplings for his air compressor-powered impact wrenches, paint guns and other tools.

“To solve the problem, I found I could simply place a plastic valve stem cover over the coupling,” says John.

“They fit perfectly to keep the ‘bugs’ out.”

From the archive · Full text
Reader shop tip

L.A. Daily

L.A. Daily, Norman, Okla.

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

“I had a lot of trouble starting my Deere 4010 propane burner in real cold weather. To solve the problem, I bought a pair of electric heating pads at the drug store and fastened them under the oil pan. I simply plug them in at night and they work great to keep the tractor starting even in the coldest weather.”

From the archive · Full text
Reader shop tip

Carroll Kerley

Carroll Kerley, Peck, Kan.

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

Carroll came up with a low cost way of repairing the openers on his Deere 494 4-row planter.

“I cut off a piece of a worn out cultivator sweep and properly shaped it to fit the opener. I then weld it to the bottom of the old opener. I weld a little hard facing onto the leading edge and it works better than new. This re-pair can be done for little or no money, while Deere wants $46 apiece for new openers.”

From the archive · Full text
Reader shop tip

John W. Morgan

John W. Morgan, Colfax, Wash.

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

“I’ve never talked to anyone who wasn’t given fits by the ‘Brake Boosters’ on some early 1970’s IHC trucks like the 1973 1310 1-ton service truck I bought used five or six years ago. The ‘booster’ was apparently standard equipment that installed between the master cylinder and engine compartment to reduce the amount of pressure needed to operate the brake pedal. The problem is that the device invariably applies pressure to the front brake first, an especially troublesome situation on ice.

“We tried everything we could think of to adjust the brake system to get equal braking front and rear but nothing worked. Finally, I simply pulled off the ‘booster’ and the original master cylinder and threw them away. I then installed a regular pickup master cylinder I had lying around. I used this master cylinder instead of the original. It solved the braking problem and made the truck a plea-sure to drive.”

From the archive · Full text
Reader shop tip

Darrell Cranfill

Darrell Cranfill, Hillsboro, Ill.

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

There are a couple of Midwestern companies that specialize in recovering old tractor steering wheels, but Darrell found a way of doing it himself.

“Plasti-Dip is a rubber coating that comes in a can. It’s normally used to cover tool handles to get a better grip. I had a dilapi-dated old steering wheel I was working on. I first built up cracks and chips with body putty and sanded those areas smooth to match the rest of the wheel.

“Then I applied several heavy coats of Plasti-Dip, using the version that comes in an aerosol spray can. It gave the steering wheel a great finish, not too shiny and not too dull. I got a like new steering wheel for the price of a dab of body putty and the Plasti-Dip, which sells for $5 per 11 oz. can.”

For information on Plasti-Dip, contact: FARM SHOW Followup, PDI Inc., 3760 Flowerfield Rd., P.O. Box 130, Circle Pine, Minn. 55014 (ph 800 969-5432 or 612 785-2156; fax 2058).

From the archive · Full text
Reader shop tip 1 of 2

Linden Hankins

Individual tip 1 of 2 from this reader’s published contribution.
Linden Hankins, Bonanza, Ore.

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

“Freeman bale chamber slide bars have a tendency to get hay and dust behind them, making the plunger hard to adjust. When replacing the slide bars, I put a bead of silicone gasket adhesive behind them and along the top edge. This prevents the problem.

From the archive · Full text
Reader shop tip 2 of 2

Linden Hankins

Individual tip 2 of 2 from this reader’s published contribution.
Linden Hankins, Bonanza, Ore.

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

“Freeman baler knives also have a tendency to wear at the bottom while the rest of the knife remains sharp. I fill the groove worn in the knife by the guide with hardfacing and grind it flat. They wear a long time and don’t add extra wear and tear to the plunger knife slide.”

From the archive · Full text
Reader shop tip

George H. Hall, Jr.

George H. Hall, Jr., Somerset, Ky.

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

George built a “poor man’s” wick wiper out of a cattle oiler rope and a few other odds and ends.

“I used 10 ft. of oiler rope wrapped around a 1 in. dia. 10-ft. long pipe. I tied the rope to the pipe with some smaller rope I had around and then tied two boxes of ‘face flips’ onto the larger rope. I slipped the pipe horizontally onto the hay forks on back of my tractor and drove out to the pasture. I soaked the rope in 2-4,D and water, which then saturated the 44 ‘face flips’ tied to it. I lowered the forks so the Face Flips dropped down 6 to 8 in. below the tops of the weeds and rode around the pasture, stopping periodically to re-coat the rope with chemical. Cost of the oiler rope was $15 and cost of the ‘face flips’ was $20. The idea has worked great on three or four farms. Kills weeds in a couple days. I would suggest using this with a front mounted tool such as loader. That way you’re not running weeds down with the back tires of the tractor before they’re treated.”

From the archive · Full text
Reader shop tip

Robert B. McKeehan

Robert B. McKeehan, Williamsburg, Ky.

Source context: Printed page 31 is PDF page 30: the scanned printed22–23 spread occupies one PDF page in this issue.

Robert recently published a 25-page booklet that describes in detail how to build and operate a farmer-size lumber kiln. He says the growth in popularity of new farm-size band saw mills means there are a lot of farmers out there with lumber to dry.

“Although commercial kiln drying can be very complicated, my approach cuts through all the jargon and technicalities and gets down to the nuts and bolts of the drying process. It covers both dehumidification and ventilation techniques. All materials and equipment can be purchased locally. In many cases, scrap materials the woodworker has lying around can be incorporated in the design. All work can be performed by the average do-it-yourselfer and the kiln can be as small or as large as you need. It’s an excellent approach for beginners and professionals alike. It also contains proven drying schedules for most popular woods, techniques for avoiding and preventing drying defects, a list of equipment suppliers and related publications.”

Sells for $12.50 including S&H. Contact: FARM SHOW Followup, Robert B. McKeehan, P.O. Box 103, Williamsburg, Ky. 40769 (ph 606 528-6707).

From the archive · Full text
Reader shop tip

Roger H. Bean

Roger H. Bean, Haydenville, Maine

Source context: Printed page 31 is PDF page 30: the scanned printed22–23 spread occupies one PDF page in this issue.

“To keep the ends of steel cable from unraveling when you cut with a bolt cutter or other tool, I use my 225-amp Lincoln welder to cut through cable. I turn the welder up as high as it’ll go and use a worn out welding rod to cut the cable. This melts all the strands in the cable ends together and prevents unraveling. I’ve cut steel cable this way for as long as I remember and it really works slick.”

From the archive · Full text
Reader shop tip

Roger W. Wessels

Roger W. Wessels, Fairbury, Ill.

Source context: Printed page 31 is PDF page 30: the scanned printed22–23 spread occupies one PDF page in this issue.

“I haven’t used the original drawbar on my Deere 4640 since I installed this heavy-duty attachment on the 3-pt. hitch. It allows me to level my 24-ft. field cultivator, disc and other implements on the go, which is a time and back saver.

“I used a length of railroad rail 10 in. wider than the original 3-pt. hitch for the main bracket. It’s welded to 12 square steel plates approximately 5 in. sq., six plates per side. Four plates are slightly shorter and weld to a round bar and rail. It secures the drawbar hitch attachment to the 3 pt.

“A stair-stepped double vertical member serves as the hitch connection. A couple angle braces complete the attachment.

“Cost was minimal. The scrap iron I used came out of an old printing press.”

From the archive · Full text
Reader shop tip

Marvin Heins

Marvin Heins, Houston, Ohio

Source context: Printed page 31 is PDF page 30: the scanned printed22–23 spread occupies one PDF page in this issue.

“After years of constantly replacing worn-out rubber bushings on my New Holland Haybine’s sickle head, I solved the problem by replacing the bushing with a ball bearing.

“It’s a simple solution but it solved the problem. The New Holland Haybine is a good machine overall but it has a troublesome sickle drive system. Our machine is 12 years old, but newer models have the same problem. We were never able to cut more than 100 acres before the bushing wore out and we had to replace it. Once we were able to cut only 5 acres before the bushing wore out.

“The bushing mounts inside a steel ring welded to one end of the sickle. The sickle drive arm uses a bolt to drive the bushing. The problem is that the arm has too much movement which causes the bushing to wear out prematurely.

“I replaced the bushing with a 1/2-in. dia. bore bearing equipped with an extended inner race on both ends. I cut off the ring where it joins the back of the sickle and welded on a new ring, using the ring’s original insert that goes into the flange head assembly but discarding the locking collar. After the weld had cooled I pressed the bushing out, then drilled three holes in the ring to match those in the bearing flange. I inserted three 5/16-in. dia. cap screws through the holes, put the washers on, and applied Lock Tite thread locking compound to secure the bearing. I then bolted the ring to the arm.

“I used a regreasable bearing because I happened to have it on hand. However, I see no reason why a conventional sealed bearing wouldn’t work. We replaced the bushing three years ago and have cut more than 600 acres since then without an ounce of trouble.”

From the archive · Full text
Reader shop tip

Guy Klosterman

Guy Klosterman, Wahpeton, N. Dak.

Source context: Printed page 31 is PDF page 30: the scanned printed22–23 spread occupies one PDF page in this issue.

“When the muffler on my Case-IH 2670 tractor fell off, I used 3/8-in. thick steel plate to build a new ‘unbreakable’ mounting bracket.

“The muffler on this tractor is notorious for falling off because the mounting hardware for it is poorly designed. It costs about $500 to replace the entire muffler system with a heavier duty one. I’ve known farmers who have welded steel fence posts from the muffler to the cab to solve the problem. I spent only about $10 on parts to make my bracket.

“I made a new heavy duty steel bracket by bending a 3/8-in. steel plate into an L shape and welding it to another steel plate that was already on the bottom of the muffler. A steel strap runs diagonally from one side of the new plate down to the original factory mounted bracket. A bolt runs through the bottom of the strap and through the factory-mount bracket to the other side of the new bracket.”

From the archive · Full text
Reader shop tip

Michael Foster

Michael Foster, Ipswich, Suffolk, U.K.

Source context: Printed page 31 is PDF page 30: the scanned printed22–23 spread occupies one PDF page in this issue.

Foster’s shop-built jig allows him to replace sickle sections without removing the entire sickle bar.

“It’s saved us a great deal of time and frustration, particularly in a difficult harvest when sickle sections are easily damaged,” he says.

The tool consists of a 2-ft. high stand with a wide base that keeps it from sinking into the ground when it’s used to brace the sickle.

A 9-in. long sq. bar welds to the top of the stand. It’s fitted with two short lengths of square bar that serve as “anvils”. They are positioned to match up with the rivet spacing on the sickle sections. At the top of each “anvil”, a dimple is drilled for the rivet head to fit into. You first grind off old rivets, remove the broken blade and then replace the blade and re-rivet. Lower the header until the blade rests on the jig and flatten the rivets against the little anvils. Be careful not to lower the header too much or the weight will damage the blade, he notes.

Shop feature stories

From the archive · Full text
Feature story

Do-It-Yourself Hose End Crimper

Featured source:

Source context: Printed page 30 is PDF page 29: the scanned printed22–23 spread occupies one PDF page in this issue.

You can repair broken hydraulic hose right on the machine without removing the hose and without the need to use a certain brand of hose ends. However, the hose and ends must be compatible, says Robert Rottinghaus, farmer-engineer from Jesup, Iowa, about the latest model of his popular do-it-yourself hose end crimper.

He first came up with his crimper tool about 8 years ago. The latest new model works essentially the same but now has infinitely variable crimp diameter - from 1/4 to 3/4-in. - on one and two wire hose.

“It works on virtually any hose in agriculture, industry or even the military,” says Rottinghaus.

“Weighs just 3 lbs. and works as well in the field as it does in the shop.”

Hose ends must be the long body style. Rottinghaus recommends the following brands of fittings for the tool: Weatherhead, Anchor-Goodyear, Dayco, Imperial Eastman, and Areo-Quip.

To fix a broken hose, you simply use the Dial Calipers that come with the tool to check the diameter of the hose end, and then duplicate that crimp diameter or refer to chart.

The kit comes in a plastic carrying case and includes Crimper, Hose End Holder, Dial Calipers, and instructions. Sells direct for $179.

Contact: FARM SHOW Followup, Robert Rottinghaus, Clever-Tech, Inc., 4121 South Canfield Rd., Jesup, Iowa 50648 (ph 319 827-1311; fax 319 827-2425).

From the archive · Full text
Feature story

Waste Oil Storage System

Featured source:

Source context: Printed page 31 is PDF page 30: the scanned printed22–23 spread occupies one PDF page in this issue.

With six tractors, five trucks, a combine, pickups and a van, there are a lot of scheduled oil changes at Ron Karlowsky’s farm near Brunkild, Manitoba.

Karlowsky used to funnel his waste oil into regular 55-gal. drums which were difficult to handle for disposal. Now, he uses a low-cost shop-built storage and transfer system to hold oil until a nearby implement dealer picks it up to burn in waste oil heater.

Three 40-gal. water heater tanks with burned out elements form the heart of the system. One tank, split in half lengthwise and covered with steel mesh holds filters and funnels, is a pour tank along one side of Karlowsky’s 4,000 sq. ft. shop. It mounts above a second tank that serves as a transfer tank. It’s fitted with a clean out valve and air pressure inlet. A third tank which is used for storage is located outside the shop.

The system plumbs together with 2-in. dia. steel pipe.

“Welding the pipe and tanks together so the fittings didn’t leak was the hardest part of the project,” notes Karlowsky.

An air compressor run at a low 30 psi’s is all that’s needed to transfer oil from the inside tank to the tank outside.

The system has a combined capacity of 100 gals. Karlowsky empties it out twice a year.

Out-of-pocket expense was about $100 (Canadian).

Contact: FARM SHOW Followup, Ronald E. Karlowsky, Box 9, Brunkild, Manitoba, Canada ROG OEO (ph 204 736-2630).

From the archive · Full text
Feature story

Working With Diesels In Ford Pickups

Featured source:

Source context: Printed page 31 is PDF page 30: the scanned printed22–23 spread occupies one PDF page in this issue.

“In recent issues, I’ve noticed comments by farmers disappointed with the performance of the 7.3 liter diesel engines in their Ford pickups. As a diesel mechanic who works on these engines every day, I’d like to offer some advice on how to extend the service life of these engines. If you follow these suggestions, it’s quite possible to get as much as 400,000 miles out of them with only minor maintenance,” says Doug McKenzie, Stony Plain, Alberta.

“The 7.3 diesel is actually a gas engine which International redesigned. Other companies have done that, too (for example, the Cat 3208). It’s just something you should be aware of in looking for a way to extend the service life.

“These engines should not be idled for more than 3 minutes due to low oil supply at the top of the engine that can cause valve and ring problems. The solution is to remove the electric solenoid on the side of the injection pump which has a 1/2-in. stroke, and install a new one with a 3/4-in. stroke. Then install a dash-mounted toggle switch which you can then use to bump up idle speed to 1,350 rpm’s.

“Another common problem is coolant leaking into the oil. This results from tiny pinholes caused by erosion to the cylinder walls. The solution is to add an anti-corro-sion additive to the radiator and test coolant on a regular basis. Never use just water.

“These engines are also prone to cracking heads. The solution is to idle the engines for two minutes before shut down. Also, you should never lug these engines. They achieve maximum torque at the top of the rpm scale and should never be run below 2,000 rpm when pulling a load.

“These engines do not stand up well to turbo charging.

“One common misunderstanding about this engine is that very rarely do the injectors used on this engine cause problems. Thousands of injectors are changed for no other reason than that the shop working on them didn’t understand that these injectors dump fuel, rather than spray.

“Oil pan heaters and coolant heaters are a must in cold weather.

“A certain amount of oil consumption is normal in these engines. A quart per 1,000 miles is quite acceptable. Oil filters and air filters must be serviced regularly and a better-than-average quality filter must be used.”

Contact: FARM SHOW Followup, Doug McKenzie, Box 2657, Stony Plain, Alberta T7Z 1Y2 Canada.