Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 27, No. 3 (2003)

Vol. 27, No. 3 (2003)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 36–39

38 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Karl Oysmueller

Karl Oysmueller, Pink Mountain, B.C.

“I made a tool for knocking tire beads off wheel rims when changing or patching tires. It’s quite simple. A solid steel rod fits inside a larger pipe. At the bottom of the pipe, there’s a short length of rod flattened to form a wedge. This wedge is free to move up and down about 1 1/2 in. on top of a spring that’s held in place by two welded-on collars. The flattened end is pushed between the rim and the tire. Holding the pipe with one hand, I use the inside rod to hammer on the bottom piece which forces the bead off the rim. It usually takes just a few blows to knock the bead off. I’ve used it on everything from car tires to big truck tires.”

From the archive · Full text
Reader shop tip

Jackson Webb

Jackson Webb, Bethune, Colo.

“The top of our Lincoln MIG welder was always cluttered with tools, gloves, helmets, and so forth, making it impossible to raise the side panels and get into the welder to change wire spools.

Also, whenever the welder was rolled across the shop floor the tools would vibrate off. To solve the problem I designed and built a metal tray that mounts on top of the welder. The tray holds the gloves, tools, etc., yet still allows me to raise the welder’s side panels without interference. I also made places to hang the helmet and welder leads.”

“The tray measures 12 by 18 in. with 4-in. sides. It’s welded to a vertical length of 1-in. sq. tubing that bolts onto a bracket that’s clamped to the front side of the welder. The tray mounts high enough above the welder that when the side panels are opened up they will clear it.”

From the archive · Full text
Reader shop tip

Profiler Inc.

Profiler Inc., Box 12858, Mill Creek, Wash. 98082 ph 360 668-3291; fax 360 668- 9533

Welding pipes together at an angle is an easier job with the company’s new “PipeMaster”. The pattern-making unit lets you quickly transfer the exact outline of the pipe joint and provides an exact fit for any angle. It’s made up of a series of spring tempered stainless steel pins that mount inside an aluminum inner shell and a plastic housing.

You slip the unit over the pipe and push down on it until the pins adjust to fit the contour of the pipe. Then you pull the unit up a ways so you can mark the location of the pins on the pipe so you’ll know where to cut it. You’re now ready to weld the two pipes together. A wide variety of diameters are available to fit different pipes.

Prices start at $37 plus S&H for a unit that fits 3/4-in. dia. tubing and goes up to $700 for a unit that fits 12-in. dia. pipe.

From the archive · Full text
Reader shop tip

Neil Ohler

Neil Ohler, Stavely, Alberta

“I recently put up a new shop building and decided to build it with an 11-ft. high vaulted ceiling, which allowed me to put in an 8-ft. door. The shop measures 24 by 32 ft. long. To put an 8-ft. high door in a building this size with a flat ceiling, I’d have needed at least 9-ft. high sidewalls and would have had to cut 1 ft. off 8-ft. sheets of plywood to get the 9-ft. height. I bought the shop package from a local building contractor. It didn’t cost much more to build a shop with vaulted rafters than it would have to build it with a flat ceiling and 9-ft. sidewalls. I put up the building by myself.”

From the archive · Full text
Reader shop tip 1 of 2

Jerome Miller

Individual tip 1 of 2 from this reader’s published contribution.
Jerome Miller, Waucoma, Iowa

“If you have 5-gal. pails that are stuck together, don’t throw them away. Instead, run water along the top of the stuck pail. The water will push the pails apart.

From the archive · Full text
Reader shop tip 2 of 2

Jerome Miller

Individual tip 2 of 2 from this reader’s published contribution.
Jerome Miller, Waucoma, Iowa

Another idea: If you have a bar of soap that has dried out, don’t throw it away. Use the soap on wood screws to make them start into the wood easier. It’ll save a lot of wear and tear on your wrist.”

From the archive · Full text
Reader shop tip

Jack Griffith

Jack Griffith, Arlington, Texas

“I have a crew cab pickup equipped with a toolbox at the front of the bed. Unfortunately, the toolbox blocks my view of the gooseneck ball. I came up with a simple way to solve the problem that makes use of a triangular magnet and a 30-in. length of pipe. I place the magnet on the bed floor and use it to hold the pipe close to the ball. I back up until the pipe is next to the trailer tongue and presto, I’m lined up.”

From the archive · Full text
Reader shop tip

Boyce Equipment & Parts Co.

Boyce Equipment & Parts Co., Inc., 226 West 20 th St., Ogden, Utah 84401 (ph 801 393-0007; email

orders@boyceequipment .com; website: www.boyceequipment.com): This company offers a complete inventory of military trucks, parts and equipment. Engines, transmissions, axles, transfer cases, winches, etc. They stock a large selection of new and used tires and wheels including like-new 1400 by 20 Michelin XLs steel belt radial tires for $250 and used Hummer 36 by 12.5 by 16.5 Goodyear Wranglers XT tires for $75 plus $25 each UPS. Also on hand are a variety of wheel rims and wheel parts for conversions or replacement. A catalog is available for $5.

From the archive · Full text
Reader shop tip

Jeff’s Bronco Graveyard

Jeff’s Bronco Graveyard, Box 227, S. Lyon, Mich. 48178 (ph 248 437-5060 or 248 486-1760; fax 248 437-9354; website

www.broncograveyard.com): This is said to be the largest seller of classic Bronco parts and accessories in the U.S. Available are 1966 to 1996 Ford Bronco and truck parts including front and rear disc brake conversions, 1966 to 1977 302/351 headers and swap kits, long travel suspension systems, sheet metal and weatherstripping, etc. A 300-page online catalog is available.

From the archive · Full text
Reader shop tip

New Tech International

New Tech International, Box 26198, Fraser, Mich. 48026 ph 800 434-9192; fax 586 758-6549; email

[email protected]; website: www.newtintl.com): Their SealLube seal expander is said to stop any rubber oil seal leaks in engines, transmissions, power steering and hydraulic systems. Problems it can solve include oil leaks of all kinds, engine wear, cracked blocks, leaky radiators, and transmission slip. It can also help with fuel efficiency and clogged fuel injectors and carb jets. The product is not designed to be used in brake systems. An 8-oz. bottle treats up to 10 quarts of oil. Small motors, pumps, gear-boxes, or other applications where there is only a small volume of liquid, can usually be sealed with just a teaspoon or so, either added to the fluid or painted on the seals on the outside. Sells for $14.95 plus $3.85 S&H.

From the archive · Full text
Reader shop tip

Transfer Flow, Inc.

Transfer Flow, Inc., 1444 Fortress St., Chico, Calif. 95973 ph 800 442-0056 or 530 893-5209; website

www.transferflow.com): This company offers auxiliary fuel tank systems for pickups designed to transfer fuel automatically to the main tank. Its newest offering is a 70-gal. in-bed tank for diesel pickups. It comes preassembled and includes the fuel tank, auxiliary fuel pump, fuel lines, wire harness, mounting hardware, and computer module. The computer module will turn on the auxiliary pump whenever the fuel level of the main tank drops to about half full. The auxiliary tank will then transfer fuel into the main tank until the stock fuel gauge rises to about 3/4 full. The transferring of fuel at set intervals will keep occuring until the auxiliary tank is empty. Because the transferring of fuel is automatic, there’s no need for a toggle switch to flip back and forth between the two tanks.

The system is available for 1990-2003 Dodge, Ford and GM short and longbed diesel pickups. Comes in your choice of bright aluminum diamond plate or black powder-coated aluminized steel.

The company also offers many other auxiliary fuel tank systems for both gas and diesel, including toolbox and fuel tank combos. An installation kit comes with every toolbox and fuel tank combo.

Prices range from $754.75 to $2,233.32 depending on model.

From the archive · Full text
Reader shop tip

Ag Staple Technologies

Ag Staple Technologies, Hutchinson, Kansas (ph 620 662-4686; website

www.agstapletech.com): This company makes a lightweight fencing tool that holds up to 48 steel fence staples at a time in a cartridge. The tool is equipped with a spring-loaded plunger and is designed to be positioned over the fence wire. You hold onto a handle and then strike the spring-loaded plunger with a hammer, which drives the staple into the fence post. The plunger then comes back up and is ready for the next staple.

“It’s faster and safer than using just a hammer and keeps you from smashing your fingers,” says inventor Ken Byard.

“The staples feed into the cartridge like a desk stapler. It works on any kind of fence wire.”

Sells for $119 plus S&H. A 5-lb. box of staples sells for $16.45 plus S&H.

From the archive · Full text
Reader shop tip 1 of 2

David I. Peters

Individual tip 1 of 2 from this reader’s published contribution.
David I. Peters, Morden, Manitoba

“I made a 40-in. extension for my shop crane that lets me lift 4 by 8-ft. sheets all the way up to my shop’s ceiling. The standard crane wasn’t able to lift the sheets more than 11 ft. high. The crane extension made putting in the sheets a one-man job instead of a two or three-man job.

From the archive · Full text
Reader shop tip 2 of 2

David I. Peters

Individual tip 2 of 2 from this reader’s published contribution.
David I. Peters, Morden, Manitoba

“I also made an extension for my step ladder by adding wooden 2 by 2’s and 2 by 4’s to the bottom of the ladder and adding a step. It raised the stepladder about 18 in. and allowed me to get up high enough to do the nailing.”

From the archive · Full text
Reader shop tip

Clifton Lawson

Clifton Lawson, 14760 Eagle Ridge Road, Ferryville, Wis. 54628 ph 608 734- 3457

“The oil filter on my tractor was stuck and wouldn’t come off with conventional filter remover tools, so I decided to make my own filter remover to do the job. I welded six pointed metal pins in a circle onto one side of a short section of steel pipe and welded a large bolt onto the other side. A nut was then welded onto the bolt. I place the device against the top end of the filter and use a hammer to pound on the nut so the pins will make marks in the filter. I either drill or punch holes into the filter at the marked locations. Then I insert the pins into the holes and drive the device all the way into the filter. By attaching a long wrench to the nut and turning it, the filter will come off. The pins grip the outside edge of the filter and don’t tear the filter up like a single screwdriver might.

“I used a 3/8-in. dia. metal rod to make the pins, which measure about 1 1/2 in. long, and a lathe to make the points. The bolt is about 7/8-in. in diameter. The reason I welded the nut onto the bolt instead of directly onto the pipe section is that it’s easier to get a wrench on the nut. The pins are slanted at a slight counterclockwise angle so that as they turn, they tend to dig into the filter and won’t come out. The pins are located at the outside edge of the filter and provide a grip all the way around it. I also made a smaller version of this tool for our car.”

From the archive · Full text
Reader shop tip

Dennis Albright

Dennis Albright, Springfield, S.Dak.

“I got an idea from an old plumber for cleaning out PVC sewer lines with a snake. You can cut a slot in the top of plastic pipes, work the snake in to unplug the pipe, and then use clamps to put a piece of rubber innertube over the hole to seal it back up. Works better than just welding a nut to the bolt.”

From the archive · Full text
Reader shop tip

Ward Bundy

Ward Bundy, Beaver City, Neb.

“Here’s a twist on an old idea for removing broken bolts from castings. If a bolt is broken off flush in a casting, I weld a washer over the end of the broken bolt and weld it in place. Then I weld a nut to the washer. I can usually screw the piece of bolt out. Works very well.”

From the archive · Full text
Reader shop tip 1 of 2

Glen Teel

Individual tip 1 of 2 from this reader’s published contribution.
Glen Teel, Hays, Kan.

“I use anti-freeze to kill rats and mice. Just cut a small hole in the side of a plastic 2 liter pop bottle, about the right size for a mouse or rat to enter, and then put a little antifreeze in the bottom of the bottle. Rodents are drawn by the sweet smell and it will kill them when they drink it. Using a bottle keeps pets out.

From the archive · Full text
Reader shop tip 2 of 2

Glen Teel

Individual tip 2 of 2 from this reader’s published contribution.
Glen Teel, Hays, Kan.

“Instant mash potato flakes will also kill mice. Put some water in a bowl next to the flakes. The flakes will swell up inside and kill them.”

From the archive · Full text
Reader shop tip

Robert Kuehl

Robert Kuehl, Davenport, Iowa

“I save time by having special purpose tool boxes for electrical, plumbing, brakes, small engines, tires, wood working, etc. There’s some duplication of tools between boxes but it’s a lot easier than trying to pick all the necessary tools off my pegboard when I head to a job.”

From the archive · Full text
Reader shop tip

Victor E. Jans

Victor E. Jans, Cupar, Sask.

“My grain auger got dented when someone backed into it. The flighting was rubbing on the auger tube. I didn’t want to take out the flighting so I came up with another solution. I welded a large nut to the outside of the auger where it was bent and then turned in a long bolt. I pulled out the dent by pulling on the bolt, thus straightening the tube. No need to re-move the flighting.”

From the archive · Full text
Reader shop tip

David Millsap

David Millsap, Abingdon, Va.

“To have air for cleaning radiators and filling tires, I installed a ball valve and female air chuck on all our trucks equipped with air brakes. Then I purchased air hoses fitted with male and female chucks to keep in each truck along with blow nozzles and tire chucks. Very handy.”

From the archive · Full text
Reader shop tip

Paul Wadeson

Paul Wadeson, Hancock, N.Y.

“I use a shovel under tires when I change my stud-ded snow tires. I just slip it under the tire and put a foot on the handle to raise the tire enough to catch the lug nuts. Simple and saves your back.”

From the archive · Full text
Reader shop tip

Charles M. Hord

Charles M. Hord, Kenton, Ohio

“I put used oil in a 1-gal. garden sprayer and use it to lubricate chains and other parts, and also on rusty parts on implements.”

From the archive · Full text
Reader shop tip

Zeke Robinson

Zeke Robinson, Ventura, Calif.

“I’ve read in FARM SHOW recently about readers having trouble starting small Tecumseh engines with less than 10 hp. I added a cup of wood alcohol or methanol, to each gallon of gas. Engines will start and keep running strong. I think the reason is that moisture gets into the fiber carburetor gaskets and causes trouble. The alcohol pulls out the moisture. I don’t know how it would work in cold weather since I live in California.”

From the archive · Full text
Reader shop tip

Charles Poole

Charles Poole, Ottawa, Ill.

“If you have a stationary engine that you only use in warm weather and is in a dusty area where keeping the radiator clean is a problem, here’s an idea. Take an empty steel drum and weld two fittings onto the drum – one at the bottom and the other towards the top. Connect one fitting the the radiator hose off the top of the engine and the other to the water intake at the bottom of the engine. Then fill the barrel with water. The water will boil as the engine heats up and you’ll have to add more now and then. But it’ll help keep the engine running cool and there’s less danger of running out of fluid and overheating.”

From the archive · Full text
Reader shop tip

James Welch

James Welch, D.V.M., Clinton, Wis.

“I’m a retired veterinarian who now volun-teers at a local conference center. Del Christiansen, the manager of the center, has a unique method of recycling oil from the grinding machines. He places a clean brown paper bag on a rack in a 5-gal. plastic pail. He then pours the oil into the bag. It takes 8 to 12 hrs. for the oil to filter through and become reeuseable. I tried it on used motor oil and found it also works well with that.”

From the archive · Full text
Reader shop tip

Bob Batteen

Bob Batteen, Urbana, Iowa

“In a recent FARM SHOW issue there was an article on problems with Super ‘M’ and Super ‘MTA’ disc brakes. The problem was they didn’t last very long. Maybe this will help. When re-pairing brakes, be sure to clean all rust, etc. The brake housing butts against the brake drum, which butts against the transmission housing. Make sure these surfaces are super clean. Then apply a thin coat of gasket maker to all these surfaces and reassemble, set brakes according to the owner’s manual, and install new boots.

“My Super ‘MTA’ is a loader tractor and sets outside all year long. The last brakes were installed four years ago.”

Shop feature stories

From the archive · Full text
Feature story

Bolt Bin Wall Uses Grain Cups

Featured source:

Gord Stein of Barrhead, Alberta, is a bit of a “neat freak” in his farm shop. He says keeping everything organized and easily accessible helps him get his work done faster and more easily. One of his best ideas was a “bolt bin wall,” he created by bolting plastic grain leg cups to a wall.

Stein made a deal with a local feed pro-cessor to buy 270 cups for 25 cents each if he removed them from the belting, which they wanted back.

The biggest job, according to Stein, was having to clean out the chaff that had become lodged in the cups. He also ground off the edges of the more damaged cups.

He used the same smooth-headed screws that held the cups on the belting to fasten them to the wall.

To make it easy to reach all the bins on the 8 by 12-ft. wall, Stein built and installed a sliding ladder on a 10-ft. section of barn door track.

He says the project took him a week of evenings to complete and his total cost was under $250.

Contact: FARM SHOW Followup, Gord Stein, R.R.3, Site 2, Box 9, Barrhead, Alberta, Canada T7N 1N4 (ph 780 674-4706).

From the archive · Full text
Feature story

“Vet” Needles Used On Grease Gun

Featured source:

A couple of issues ago FARM SHOW published a story about a tool that holds any standard grease needle firmly in place on a grease gun, making it easy to lubricate bearings (Vol. 26, No. 5). The story prompted Alec Yeager of Hendley, Neb., to tell us about a somewhat similar tool that he thinks works even better. He designed it back in the 1980’s and is now offering it for sale. It’s called the “Bearing $aver.”

The stainless steel tool is tapered at one end to accept veterinarian needles. A cap is then screwed over the needle to hold it in place. A zerk can be screwed into the opposite end of the tool, or the tool can be screwed directly to your grease gun.

“I have yet to find a veterinarian needle that won’t work,” says Yeager.

“I came up with the idea because standard grease needles are expensive and don’t last very long when you’re trying to force them under bearing seals. Veterinarian needles don’t last much longer. However, when you buy veterinarian needles in volume they’re quite cheap. I buy standard 1-in. 24-ga. veterinarian needles in boxes of 100. Another advantage is that I always have a new sharp, straight needle whenever I need one. The needle can also be used to force glue into cracked furniture.”

Sells for $24.75 plus $2.25 S&H. Contact: FARM SHOW Followup, Alec Yeager, Box 504, Hendley, Neb. 68946 (ph 308 265-7466; website: www.kisoffroad.com).

From the archive · Full text
Feature story

Simple Small Engine “Oil Vac”

Featured source:

Leland Saele, Ft. Worth, Texas, used a shop vac, a 5-gal. bucket, and a 1-quart oil bottle to make a dandy “oil vacuum” for sucking oil out of his Honda lawn mower engine.

“It was cheap to put together and makes changing oil in the mower a much cleaner and easier job,” says Saele.

Saele came up with the idea after he bought the mower used and tried to change the oil for the first time.

“I assumed the drain plug would be underneath the mower, but when I looked underneath it wasn’t there. Instead, it was located at the base of the filler tube, on top of the engine crankcase. To drain the oil, I would’ve had to tip the mower over which I thought was ridiculous. So I came up with my own solution. I think the same idea could be used with any small engine.”

Saele places an empty oil bottle in the bucket, then covers the bucket with a piece of 1/4-in. thick plexiglass with two holes cut in it. One hole is the same size as the shop vac hose and the other is just big enough for a length of 3/8-in. dia. clear plastic tubing. One end of the tubing is inserted into the filler tube on the mower and the other end is inserted through the hole in the plexiglass lid and into the oil bottle. The vacuum hose is inserted through the other hole in the lid.

Saele simply starts the vacuum and watches the oil go through the tubing and into the oil bottle, which has a transparent neck so he can watch it fill. When the oil level is close to the top he shuts off the shop vac and puts in a new container. He repeats the process until all the oil has been removed from the crankcase.

“It’s a simple idea but it works good,” says Saele.

“The plexiglass came from a broken pad that had been used to protect carpet under an office chair. The plexiglass should be slightly larger than the top of the bucket, and it should be thick enough so it doesn’t collapse from the vacuum pressure. The tubing has to be pushed all the way down to the bottom of the crankcase in order to remove all the oil.

“Cleanup is simple. I put a plastic cap on each end of the tubing and hang the bucket, with the tubing in it, in my garage until the next time I need to use it. Storage of the bucket isn’t a problem since it stays clean and can be used for other purposes,” he notes.

Contact: FARM SHOW Followup, Leland Saele, 7853 Colwick Court, Ft. Worth, Texas 76133 (ph 817 346-9819).

From the archive · Full text
Feature story

Portable Welding Shop Mounts On Old Garbage Truck

Featured source:

Brian Esser, Minnesota Lake, Minnesota, operates a portable welding service that serves farmers and truckers, among others.

Over the years, he’s put together six different rigs to haul tools and power to welding sites.

“I’ve put them on trailers and smaller trucks, but I never had one that would handle everything I might need. I was always running back to the shop for something,” he says.

So for his newest portable welding rig, Esser found a 1981 C70 2-ton Chevrolet truck cab and chassis and went to work.

“The truck had been a single axle garbage truck, so it already had a good set of springs under it,” he says.

“The first thing I did was to extend the frame, making it 30 ft. long from bumper to bumper,” he says.

Then he built a utility bed on it that’s only a 20-in. step up between the wheels.

“I made shelves and compartments all around it that are accessible from the ground, as is all,” he says.

With the exception of one tool cabinet, he made all the cabinets on the truck from aluminum deckplating. All have hinged, locking doors.

Besides welding tools and supplies, his cabinets hold the equivalent of a small hardware store.

“I have large quantities of the most common sizes of screws, bolts, nuts, steel rod, flat steel, angle iron, etc., on the truck,” he says.

“It’s often a 20-mile round trip or more to the closest hardware store, so having the truck stocked saves a lot of time and expense. A trip to the hardware for four or five bolts costs the customer an hour of my time or more.”

Most of the welding equipment and storage is centered around a 50-ton iron worker that he uses to cut and shape steel on site.

Then there’s an 8,000-watt gasoline engine-powered generator, a 250-amp stick welder and a 250-amp wire feed welder. He mounted oxygen and acetylene tanks on one side, with 100 ft. of hose that lets him get his torch into just about any place where he needs it.

The generator provides power for the welders, and several other power shop tools, including a drill press. Tucked into one of the cabinets is 200 ft. of 220-volt power cord, so he can take the welders off the truck if he needs to.

Other components include portable and fixed lighting, so he can work any time of day or night. Some of his portable lighting draws power from the generator. For the truck mounted lights, though, he replaced the stock alternator with a heavy-duty 100 amp model, which keeps the truck battery and a bank of back up batteries well charged.

Tucked into one cabinet is a 220-volt air compressor with 150 ft. of hose. The compressor is plumbed into outlets on both sides of the truck, so he doesn’t have to run the hose over or under the truck to get to his work.

“I had another smaller compressor on the truck at first, but it didn’t put out enough air for my plasma cutter,” he says.

There wasn’t room for the plasma cutter on the truck and Esser says he doesn’t usually need it. When he does, he takes it along on a pallet that fits into the receiver hitch on back of the truck.

While he spent a lot of time designing the truck, he says he had to make some changes and it took quite a bit of on-the-spot engineering to get it all to fit together. One of the main concerns in the design was that the truck fit inside his shop, which has a 96-in. doorway.

He figures he has more than $50,000 invested in the portable welding shop, including his small rolling hardware store.

Contact: FARM SHOW Followup, Brian Esser, 53478 250th St., Minnesota Lake, Minn. 56068 (ph 507 462-3651; email: [email protected]).

From the archive · Full text
Feature story

“Oil Caddy” Made From Office Chair

Featured source:

Gord Stein likes the fact that he doesn’t have to fumble with a funnel or have to lift up his transmission oil or gear oil pails when doing maintenance to his trucks. The Barrhead, Alberta, farmer made a two-pail oil holder using the castor wheels off an old office chair.

Using flat iron, he fashioned a platform for the pails to sit on. This is welded under the castor leg assembly. Strap iron side brackets hold the pails in place.

The 5-gal. pails are fitted with hand pumps and hoses on the lids so that no lifting is re-quired at any time. The rig can be rolled around the shop or out onto the gravel outside, according to Stein. The castors are extremely stable, and the unit is well balanced. It doesn’t even tip over when one pail is re-moved, so varying levels of lubricant in the pails have no effect.

The cost to Stein for the “oil caddy,” was negligible, since materials were all salvaged and it took only an afternoon to build.

Contact: FARM SHOW Followup, Gord Stein, R.R.#3, Site 2, Box 9, Barrhead, Alberta, Canada T7N 1N4 (ph 780 674-4706).

From the archive · Full text
Feature story

Dodge 4-WD Transmission Fix

Featured source:

If you drive a Dodge 4x4 diesel pickup made in 1994 or later equipped with a standard 5-speed transmission, or if you’re thinking about buying a used one, you may need to talk with Dan the Gear Man.

The Gear Man, known to his friends as Dan Guarino, says as many as 25 percent of these transmissions will fail due to wear on the fifth gear main shaft.

“The main shaft is 2 in. long, but has splines only on the outer 3/4 in. of the shaft. Under heavy loads, the gear wears into the shaft past the splines,” he says.

“That lets the shaft work loose and the nut that holds it in place comes off.”Guarino says this usually shows up on trucks with more than 100,000 miles, but notes he’s seen it happen as soon as 35,000 miles. It’s more likely to show up on trucks that are used extensively for pulling heavy trailers at highway speeds.

Guarino fixes the problem with his own version of the main shaft.

“Once the shaft is worn, it’s shot and has to be replaced. The dealer fix is to replace it with the stock shaft, so the problem will likely occur again. Our Extreme Duty Mainshaft will fix it permanently,” he says.

“Our shaft has splines the full length, so the gear is always fully supported. This way, it can’t work loose and wear out,” he explains.

The Gear Man’s transmission fix usually costs around $1,600.

“By the time the owner gets it to us, the truck usually has a fair number of miles on it and we have to rebuild the transmission. If it comes in before it’s shot, we can fix the transmission for less than that,” he says.

Contact: Farm Show Followup, Dan Guarino, Quad 4X4, RR 1, Box 2059, Roberts, Montana 59070 (ph 406 446-2427; website: www.quad4x4.com).

From the archive · Full text
Feature story

3-Pt. “No Freeze” Fabric Roller

Featured source:

John Dansby, Rocky Mount, Virginia, says covering his large fruit and vegetable plots to protect them from frost used to be a real hassle, but he solved the problem with a tractor-mounted roller.

“I use a strong spun polyester-type synthetic material to cover my strawberries. It protects them from freezing at temperatures as cold as 20 degrees Fahrenheit, but lets air and water pass through.

“The material is 50 ft. wide, folded to a width of about 10 ft. and rolled up on a cardboard spool. Unrolling it and spreading it out was difficult. Rolling it back up after you’d used it was even worse,” he says.

So Dansby sketched what he wanted and took it to a local fabricating shop where they produced it for him.

The roller/unroller mounts on his tractor 3-pt. hitch.

“It’s a steel frame that’s about 12 ft. wide and extends back behind the rear wheels. It looks sort of like a big toilet paper holder,” he explains.

Dansby’s frame has a 2-in. cradle on both ends. A hand winch operated from the tractor seat allows him to disconnect the top link on the unroller and lower the back end of it to the ground. To load a spool of material onto it, he releases the top link and lowers the unroller. He inserts a 13-ft. length of 3-in. steel pipe through the cardboard tube and sets the ends in the cradles. He then winches the frame back up and re-attaches the top link.

Rolling the fabric back up is easy, too.

“It has a hand crank welded to one end of the steel pipe. The cardboard tubes aren’t very sturdy, so we don’t reuse them. Instead, we put a 10-ft. length of 3-in. inside dia. PVC pipe over the steel pipe and pin it in place on the roller with a bolt inserted through both the PVC and steel pipes. I fasten the end of the material to the PVC pipe in three or four places with duct tape. Then we just wind it up,” he says.

Once the fabric is re-rolled, he covers it with black plastic, fastened on with duct tape and stores it.

“It doesn’t make as neat a roll as when it was new, but it gets it off the field and in a roll so we can store it and use it again,” Dansby says.

He says if the material is wet, he can fasten it to the unroller and pull it off the field to a grassy area to dry before rolling it up again.

“I thought about using a hydraulic cylinder in place of the hand winch, and I may still put a hydraulic motor on the crank to make it easier to pick up the plastic,” he says.

“But it works great as it is and saves us a lot of time.”

Contact: FARM SHOW Followup, John Dansby, 4481 Colonial Turnpike, Rocky Mount, Va. 24151 (ph 540 576-3658).

From the archive · Full text
Feature story

Portable Sail-Type Windmill

Featured source:

Robert Green doesn’t need a tower for his horizontal windmill. He doesn’t need a bunch of gears or blades. He doesn’t even need much wind.

“It only takes 3 to 5 mph wind to turn it,” he says.

Green, a retired mechanical engineer, designed his horizontal windmill using collapsible sails instead of blades. Instead of a tower, the sails ride atop a slender pole. As it turns, it transfers power directly to ground level through an internal rod. The external tube serves as both a vertical support and an an-choring point for guy wires.

The simple design means it can be erected in a matter of minutes wherever it’s needed. Green has used it for pumping water and air on site and has even developed a unique, low-load pump to use with it.

“It can be set up by a pond that needs to be aerated or in the center of a flooded field to pump away excess water,” says Green.

The novel windmill uses four opposing sails on a wheel and spoke framework atop the pole. As each sail moves into the wind, it opens up like the sail of a sailboat, driving the wheel around the pole. As one sail fills, it pulls against cables on an opposing sail, keeping it tightly closed.

The closed sail, which resembles a wing on an airplane, also captures the power of the wind. Just as the different amounts of air pressure lift the wing of an airplane, the air moving across the closed sail creates lift. It also drives the wheel. As the wheel turns into the wind, the process is repeated by each pair of sails.

“Traditional windmills are drag windmills, while new propeller windmills are lift windmills,” explains Green.

“This is sort of in between.”

He hasn’t adapted the device for electrical generation.

“I am not an electrical engineer, that’s not my field,” admits Green, though he is confident the design could work if someone had the expertise.

Green sees his system first and foremost as a ready form of mechanical energy that can be adapted as needed. He doesn’t sell the windmill itself, but does market plans and rotor kits. He offers hardware kits for 24- and 48-in. rotors at $59 and $118 plus shipping. Green reports selling several hundred packages. Many have gone to Asia, India and other lesser developed countries. In the U.S., they have proven most popular in the West and Southwest.

“What I am offering is a formula for making this kind of windmill,” he says.

“They can take it from there and make whatever they want from it.”

Contact: FARM SHOW Followup, Robert Green, 1222 W. Grand Ave., Chicago, Ill. 60622 (ph 312 226-7584; website: www.greenwindmill.com).

From the archive · Full text
Feature story

Sens-Alert Tells Growers When Hay Is Ready To Bale

Featured source:

Western hay producers must often wait for dew to dampen alfalfa crops in order to minimize losses during baling.

“My sister owns an alfalfa ranch in Oregon, and she would sleep in her pickup in the field so she’d know when the dew was heavy enough that she could bale,” says Martin Lilly, Goleta, California.

Lilly figured his sister and other alfalfa growers could get a decent night’s sleep if he could put moisture sensors in their hay fields that would alert them when conditions were right for baling. He happened to work for a company, Dynason, Inc., that makes various electronic sensing devices.

After several years of work, Lilly came up with a product called Sens-Alert, which can reliably detect dewfall and send a message on a mobile radio, cell phone or pager.

Lilly says each of his Sens-Alert systems is custom built for the owner.

“In addition to alerting the hay producer that field conditions are right for baling, we can design the system so that the producer can dial up the system on his cell phone and get a report on current field conditions. And we can add a feature that allows him to use his phone to switch on a beacon on the unit, so he can easily find it when he arrives at the field in the middle of the night to begin baling. This one is important because some people have been known to lose track of where they placed the unit,” he says.

While Sens-Alert was designed for Western hay growers, Lilly says he can adapt the units to monitor temperatures in fields (needed to track development of certain pest insects), soil moisture conditions, moisture and temperature in stored grain, and more.

“We can equip them with motion sensors to detect intruders and then notify farmers or law enforcement officials,” he says.

He says a possible application would be to monitor grain moisture in batch drying bins, enabling producers to know exactly when grain can be moved to storage and the bin can be refilled.

Another application he’s recently worked on is in conjunction with a switch on a gate, so if the gate is opened without authoriza-tion, the system calls the farmer and the sheriff’s office.

“This was designed by a hay grower who was having problems with theft of baled hay,” he says.

“I’ve been approached to design a system that will notify dairymen when their hay has wilted enough to chop for haylage,” he says.

“I haven’t had time to find the right sensors and test them for this, but it is possible.”

Price for a Sens-Alert system varies according to the application and the different bells and whistles incorporated into it. However, a system with notification by cell phone usually costs between $1,500 and $2,000. A typical system weighs less than 20 lbs.

Contact: FARM SHOW Followup, Martin Lilly, Dynasen Inc., 20 Arnold Place, Goleta, Calif. 93117 (ph 805 964-4410; fax 805 967-2824; email: [email protected]; website: www.dynasen.com).