Albert Schollenberger
“When replacing bearings, I put the new bearing in the freezer for 4 hrs. before attempting to install it. The bearing shrinks enough that it falls into place without requiring a great deal of pressure.”
Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 36–39
31 selected entries · Complete text of selected entries
This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.
“When replacing bearings, I put the new bearing in the freezer for 4 hrs. before attempting to install it. The bearing shrinks enough that it falls into place without requiring a great deal of pressure.”
“When welding a piece of rusty equipment, it’s sometimes a problem getting a good ground with the ground cable clamp. Here’s a remedy. First clamp a common vise-grip wrench on the rusty spot, and then clamp the cable onto the vise-grip. Works every time.”
“I made a nifty rolling shop chair out of a small kindergarten chair fitted with large caster wheels. It rolls easily wherever I need it.
“To make it easier to adjust a floor jack, I welded a large washer to the adjustment screw that you normally turn with the handle. It’s a lot easier and quicker to use than trying to fit the handle into the slot.
“I took several pieces of short chain and made one longer chain by putting a bolt through the end links of each piece. Works great as long as you use it for light work.”
“In regard to the Florida gentleman in a recent issue who was having trouble with ethanol fuel in small engines, go to your nearest airport and get aircraft fuel, which is 100 percent ethanol-free. In my opinion, the ethanol content cuts oil film in 2-cycle oil and fuel mixes, resulting in lubrication-starved engines.”
To make it easier to make tough cuts with his bolt cutters, Paul attached a round piece of plate steel to one handle so he can place it flat on the ground and apply force to the upper handle. He says the idea comes in handy for cutting chunks of metal that would be difficult to cut otherwise. Applying force from above multiplies the cutting force.
Tim believes in making his shop tools portable. Portable tools can be rolled to the job, and they also make it easier to keep the shop clean. That’s why he mounted his chop saw on a lightweight rolling wood table. He used 2 by 4’s and 2 by 6’s to build it, with caster wheels at the bottom. The table top is plywood and there’s a shelf underneath to hold scraps.
Tim also mounted a metal break and roller on top of a rolling warehouse truck that he bought at a factory closeout auction. The truck is heavy enough to carry the tools easily and handle the pressure applied. One metal break will bend 36-in. metal, limited to a 1-in. flange. On the opposite side is a box and pan break that makes 24-in. breaks, making 4-sided pans 4 to 5 in. deep. At the end of the cart he mounted a sheet metal roller. It lets him make cylinders about the size of a rain downspout.
“I came up with a simple, easy and cheap way to mount wire spools to keep them out of the way but within easy reach. The rack only requires a few 2 by 4’s, some electrical conduit, and some baling wire. The best part is that you can set it up in a few minutes. I just wire 2 by 4’s to open studs and crossbars in my shop, and wire the ends of the 2 by 4’s to the studs up above. I drill holes through the 2 by 4’s and slip in pieces of electrical conduit. The reels go on those. Works great for all kinds of wire, rope or chain, and you can pull lengths off the reels easily as needed.”
Kleen Chain, from the manufacturers of the popular Magna Guard magnets for oil filters, is a new way to lube chains. With spray-on lubes you can’t control how much product is applied and you can get messy overspray. The new Kleen Chain is a synthetic lube designed specifically for chains and is applied with a glide-on applicator. The gel formula is thick enough to stay on, even at high rpm’s but not so sticky it attracts dirt. Can be used on any kind of ag machinery, ATV’s, motorcycles, bicycles, and even hand tools. It’s available in a 4-oz. bottle from dealers or at www.kleenchain.com for about $9.95. A larger ag size will soon be available.”
“A while back someone wrote about weld- ing on a compressor tank. I just want to remind people not to weld on any tank that is pressurized. One of my friends got killed when he attempted to do it. The tank was like a cylinder in an engine, at the top of its compression stroke. Oil can leak into the compressor from the tank. As soon as you strike an arc, it’s like the spark plug firing and the tank will explode.”
“This handy hoist, built from a discarded swing set, provides me with a safe and easy way to clean the deck and sharpen the blades on my riding mower. Once the riding mower is on the hoist I can pull up a seat on rollers and work from a sitting position.
“First I shortened the swing’s overhead horizontal pipe to about 6 ft. wide. Then I slipped a heavier 2-in. dia. galvanized pipe over the pipe to reinforce it, and used 1⁄4-in. sheet metal screws to secure the two pipes. I used no. 60 roller chain to secure a 1 1⁄2-in. dia. pipe below that, and mounted an electric winch on it. I use a remote control to operate the winch, which I bought at Harbor Freight for about $60. It has better than a 400-lb. rating. Small wheels on the legs make the swing easy to move around.”
“To remove a stud that has broken off flush, I lay a flat washer over the broken stud and weld the two together. Then I weld a nut to the washer and remove the stud by working it back and forth. On a really tough stud, first I drill a hole in the middle of the stud and then jam in a small welding rod so I can heat the inside of the stud, which causes it to shrink and loosens it up. Then I weld the washer and stud together and weld a nut to the washer. I’m a retired Deere dealer, and over the years our shop mechanics often called on me to remove broken studs so I know this method works. I’ve removed literally hundreds of studs this way.”
“I made this drill press vise out of 1⁄4-in. thick by 2-in. angle iron, a piece of 6-thread-per-inch, 3⁄4-in. dia. threaded rod, and some other scrap material. I also made one for my brother-in-law and for a neighbor that opened to 12 in.”
“My multi-purpose Truk-R-Tool is designed for truck drivers but it comes in handy for just about anyone. The 17-in. long, powder-coated tool has a railroad spike welded to a hollow steel pipe handle. There’s a steel retractable hook inside the handle.
“The tool’s hammer end is used to thump tires, repair pallets, drive nails, etc. The spike’s sharpened, tempered chisel end is useful for ratcheting strap winches, chipping ice off equipment, breaking rocks out of dual tires, and so forth. The 30-in. extended hook is useful for pulling tractor kingpin and trailer slider releasing levers, pulling tarps and tarp straps, and helping to install truck tire chains.
“Our Drill Bandit attaches to most pistol-type drills and allows you to put as much pressure as you want on the drill bit simply by squeezing the ratchet. Works great in many difficult-to-drill applications.
“The Drill Bandit is compatible with most 1⁄2, 3/8 and 1⁄4-in. pistol-type drills. A 1-in. nylon strap and ratchet mechanism allows the operator precise control of the amount of pressure he puts on the bit.
“The unit will provide more than 150 lbs. of pressure at the drill point. Competes with $1,000 mag drills which weigh more than 50 lbs. and require a fairly flat surface for mounting.
“My friend used the unit to drill 24 3⁄4-in. dia. holes in 1⁄2-in. thick steel I-beams in order to mount his school’s scoreboard.
“Sells for $175 plus $10 S&H.”
This company’s new tire repair kit allows for an “on the spot” and “on the wheel” repair to virtually any tubeless tire, and it seals the puncture on the inside. The Plugger is a spring-loaded gun that “drives” the plug into the hole. The shaft of the plug expands under pressure to fill the puncture. The mushroom head of the plug seats on the inner wall, without allowing air to escape. The tool comes in a vinyl-zippered 6 by 9-in. pouch and weighs just under 2 lbs. Included is the plug gun, nozzle, probe tool, reamer/rasp tool, retractable blade, and 25 rubber mushroom plugs that measure 5/16 in. in diameter and 3⁄4 long, along with detailed instructions. Sells for $43.95 plus S&H. An extra bag of plugs sells for $7.50 plus S&H. The company also offers a Pocket Tire Plugger that installs mushroom-shaped rubber plugs into all tubeless tires while still on the wheel. The Plugging device “drives” the plug into the hole with the turning of a hex wrench. The plug expands under pressure to fill the punctured area. A firm pull of the stem with a pliers seats the mushroom head on the inner wall, allowing no air to escape. Sells for $31.95 plus S&H.
He uses a simple trick to get bolts through openings where you can’t get your fingers inside. He wraps a piece of .035 welding wire tightly around a 5/16-in. bolt.
“I wanted it to fit a 3/8-in. bolt, but you have to go one size smaller than the size you need to keep the wire tightly wrapped. Then you just thread it on the bolt and, viola, you have a fishing tool that makes it easy to pull the wire and bolt through a hole. Afterward, you can turn the wire off when you’re done putting the bolt in place.”
“I’ve found endless uses for rare earth magnets around the shop. I have steel walls and cabinets in my shop so I’ve got these little magnets stuck all over the place, holding parts, manuals, etc. They’re so unbelievably strong that if two were stuck to each other, you wouldn’t be able to get them apart without a pliers.
“I have them attached to my shop press for holding accessories that I use daily. I also use them to hold hitch pins on my tractors when they’re not in the drawbar. I use magnets in too many places to list them all.
“My good friend, Jon ‘Sparky’ Anderson, who recently died in an automobile accident, originally told me about the Amazing Magnets website (Amazing Magnets.com). He had a fascination with magnets, too. You can get nearly any shape and size of these rare earth magnets.”
Jason Gogerty and his brother Jordan used a cutting torch to turn an unused 5,600-bu. grain bin into a storage shed. They keep their small tractor, garden equipment, tools and supplies in it. They cut a large opening in the bin and used 6 by 6’s to build a wooden frame that’s screwed to some angle iron for reinforcement around the opening. The angle iron is embedded in cement at the bin’s floor. They used 2 by 4’s to frame two big 5 by 8-ft. plywood doors and mounted three big strap hinges on each door.
Jason’s father Tim plans to use the grain bin shed in his hay rebaling business, in which he rebales round and big square bales into small square bales. He has been using a tractor inside a hoop shed to operate the baler and unroller. In the future he’ll install a stationary engine, removed from a combine, inside the bin which will free up the tractor. Contact: FARM SHOW Followup, Jason Gogerty, 33094 K Ave., Hubbard, Iowa 50122 (ph 641 487-7825).
“I changed the shape of one of the skid shoes on my Deere 630 Hydra Flex combine header because it wasn’t working as well as I wanted,” says Roger Gutschmidt, Gackle, N. Dak. When combining this year’s soybean crop under wet conditions, the skid shoe on the left side (under the knife drive) kept pushing up mud and dirt. He solved the problem by flattening the steel skid plate to more of a gradual incline. He had to remove the skid shoe from the combine and place it in his press.
“It’s made out of some real tough material that could not be shaped without taking it off the machine. Once I had flattened it in the press, I had to weld in a pie-shaped piece of sheet metal,” he says.
“The project took about 3 hrs. in all, but 2 hrs. of that was removing it and reinstalling it on my header.” According to Gutschmidt, the poly skid material on the underside was not changed or altered, so the replaceable pieces can still be purchased at any Deere dealer.
“Once in place, the modification is almost impossible to see, and it works perfectly. There’s no more pushing dirt,” he explains.
“I’m surprised the factory engineers couldn’t see that there’d be problems the way it was shaped originally.” Contact: FARM SHOW Followup, Gutschmidt Manufacturing LLC, Roger Gutschmidt, 6651 Hwy. 56, Gackle, N. Dak. 58442 (ph 701 698-2310; [email protected]).
Before you buy that next new tractor or truck, you may want to ask if it has a Fluid Property Sensor (FPS). If it does, you’ll probably save money on oil and other fluids because you’ll only change them when they really need it. The new sensor can also tell you if coolant is leaking into the oil or if incomplete combustion is occurring, adding soot to the oil. The Measurement Specialties sensor is now being sold to OEM’s but should also be available soon for aftermarket use.
“The FPS offers fluid sensing on-the-go,” says Mark Uhrich, Measurement Specialties.
“No other sensor on the market will measure viscosity, density and dielectric constant simultaneously.”
It also measures temperature, but it’s the other three measurements that make this sensor so amazing. Contaminates like soot, water, ethylene glycol coolant and fuel in engine oils are easily detected. Each changes one or more of the physical properties measured by the FPS.
An onboard microprocessor provides real time data analysis using algorithms developed for the fluid being monitored. At its simplest, an OEM might use the sensor to trigger a warning light telling the operator to take the engine to the dealer. Once there, fault codes can be used to tell the dealer that the soot load is too high or water has been detected, suggesting a coolant leak.
“Oil is kind of like a diary,” says Uhrich.
“If you can detect a problem early, you re-duce or avoid the engine wear that can create failure or require a rebuild.”
While having an oil sample analyzed can provide much of the same information, it is a snapshot in time. A few seconds after the sample is taken, a problem can develop. The FPS is like a security camera with real time monitoring from an on-board oil analysis laboratory. It will dramatically expand current capabilities based on multiple, single use sensors.
“Caterpillar and others already offer remote equipment monitoring that reads information and transmits it to a central location,” says Uhrich.
“GE gets information from aircraft engines in the air and understands how they are operating.”
It may be only a short time before engines will be able to communicate directly with a preferred service provider, whether a dealer or a local mechanic. Alternatively, the information could be fed to an onboard terminal that displays the results to the operator and recommends actions to be taken.
Contact: FARM SHOW Followup, Measurement Specialties, 1000 Lucas Way, Hampton, Va. 23666 (ph 757 766-1500; toll free 800 745-8008; fax 757 766-4297; www.meas-spec.com).
“We do site prep work for timber companies, and the brush is hard on hydraulic hoses,” says Robert Raymond, Cove, Ark.
“We started making hose protectors from plastic pipe, cutting it in spirals with a knife, to slip around the hoses. It was hard work and took a lot of time, so I came up with a simple cutter that does it fast and easy.”
Raymond starts with plastic pipe with an inside diameter to match the outside diameter of the hydraulic hose. He then selects a 4 to 6-in. length of steel pipe just large enough for the plastic pipe to slide through and welds short lengths of smaller pipe to each side of the cutter pipe for handles. They provide needed leverage when cutting the plastic pipe.
To make the cutter, he drills a hole near the end of the pipe for a 3/8-in., no. 8 grade or better bolt. He fastens the bolt in place with a 1/2-in. nut on the outside and a lock nut on the inside. He then welds the outside nut to the pipe, removes the lock nut and grinds the end of the bolt to a cutting edge.
“I leave the back edge of the cutting face slightly thicker for added strength,” says Raymond.
“You need to take your time when grinding the bolt down so you don’t overheat it.”
Grinding out the face creates a curved cutting edge. The angle of the face determines the width of the spiral that leaves the pipe. The flatter the face, the narrower the spiral will be. If it is too wide, it is hard to open it up to wrap around the hose.
“I made a selection of cutter pipes to match common hose diameters, including 1/2-in., 3/4-in., 1-in., 1 1/4-in. and 1 1/2-in.,” says Raymond.
“Sometimes the larger diameter plastic pipe can collapse as it is being forced through. I place a small insert opposite the cutter blade to keep the plastic pipe in place.”
Raymond notes that the cutter can be made from all scrap parts. It has saved him a lot of money over the years, both in protected hydraulic hoses and not buying commercial protectors.
“I looked at the wraps available, and they cost $12 per foot or more,” says Raymond.
“My only cost is the plastic pipe and my time. When hoses are covered like this, I can bundle them and tie them. I use them on brake lines too. It just about stops wearing rubber off the lines.”
Contact: FARM SHOW Followup, Robert Raymond, 495 Polk Road 233, Cove, Ark. 71937 (ph 580 244-3212).
Frame walls out of line? Ready to grab a mall or pry bar to bring them back? Contractor Keith Kennedy was tired of pounding on walls, and the only wall puller tool on the market required at least three hands to work. So, he designed his own tool.
“I developed the WoodRatchet so I could let go of it to reach for the nail gun,” he explains.
“I made the ends out of flat plate with a spike in it and attached them to a ratcheting binder.” To pull in a stud wall, for example, he hammers the spike of one end to the plate and spikes the other end to the floor. Then he ratchets the wall in place, nails it down and removes the tool with his hammer claw.
“After I started using it I found many other uses for it,” he says. Instead of requiring three people to move diagonal braces to level walls, he can do it himself.
“There are holes in each corner of the ends to add a nail or two to if you have a really stubborn pull or a vertical pull,” Kennedy says.
“But most of the time you don’t need nails. You can also flip the ends around and push with it.” He used the WoodRatchet for four years - lending it frequently to other carpenters - before he patented and started selling the tool out of his shop. The ends are made of 1/4-in. steel with 3/16-in. sharpened shark tooth-like spikes. The tool can pull or push up to 3 in.
“As soon as builders see it, they say it’s a good idea, and they wish they had thought of it,” Kennedy says. He sells WoodRatchet for $69.95 plus shipping through his website, which includes videos of the tool in use.
Contact: FARM SHOW Followup, Keith Kennedy, Kennedy Mfg. LLC, 174 Monroe Lake Shores, E. Stroudsburg, Penn. 18302 (ph 570 223-0527; www.woodratchet.com).
If your truck or tractor is using a lot of oil, it could be due to excess crankcase blow-by. A filtration system from Donaldson can recover that oil. The Spiracle filtration unit vents the blow-by from the crankcase and filters out particles such as soot. It also captures, condenses and returns oil particles to the engine sump. The Spiracle is OEM-installed on many large farm, construction and fleet engines. It is also available for retrofit.
“It captures oil that would otherwise be lost and returns it to the engine sump,” explains Veli Kalayci, Spiracle team leader.
“The gasses are filtered of soot and other par-ticulates and returned to the turbo or released, depending on the engine.” Spiracle crankcase filtration is used in Tier 3 and Tier 4 engines primarily for emissions control. However, Kalayci says the oil captured can be significant, especially as an engine ages.
“The amount of oil saved by the filtration system depends on engine size, duty cycle, operating conditions and life of the engine,” says Kalayci.
“The more wear, the more crankcase blow-by. Blow-by can have a big impact on oil consumption.” Chris Purdy, Spiracle product manager, would only say that the units are priced competitively. Distributors and dealers can be reached through the company. Contact: FARM SHOW Followup, Donaldson Filtration Solutions, Emission Systems, 1400 W 94th St., Bloomington, Minn. 55431 (ph 952 887-3058; toll free 866 675-2847; fax 952 698-2510; [email protected]; www.donaldson.com).
An unused semi trailer can be turned into an easily accessible, low-cost storage area by adding a deck and stairs on back, says Bruce Dunahoo, Zearing, Iowa. A friend helped Dunahoo build the deck and mount shelving on the walls inside the semi.
“I use the trailer to store parts, lumber, and supplies. It’s really handy,” says Dunahoo.
“The trailer is close to my machine shed and driveway.” Contact: FARM SHOW Followup, Bruce Dunahoo, 14231 U.S. 65, Zearing, Iowa 50278 (ph 641 487-7328).
“So many small-town service stations have gone out of business that there is no place to get a tire fixed after 5 p.m.,” notes Bruce Docter at Your Next Tire, which sells discount tires online and recently introduced a line of “affordable” tire changing equipment.
“We sell three different tire changer models. The 300 Series will handle rims up to 20 in., the 500 Series handles rims up to 24 in., and the 700 Series handles rims up to 26 in.”
The 500 and 700 Series have heavy-duty bead breakers. They can handle everything from ATV’s to semi trailers. Both also have a larger air tank with an optional bead blaster for seating beads on truck tires.
“With more farmers having semis, they need a way to fix the tires when a tire shop isn’t open,” says Docter.
“Our heavy-duty bead breaker will handle them, but users needed a way to seat the bead when finished. We made an attachment for our air tank that will blast air into the truck tire to seat the bead.”
Unlike bead-setting machines that sell for $350, his attachment does the same job for just $150. The three tire-changing machines sell for $1,200, $1,700 and $1,900, respectively.
“The smaller machine is really for lighter tires,” says Docter.
“We try to discourage farmers from buying it. The $1,700 500 Series is the most popular.”
Docter also sells spreader attachments for the tire machines, so tires can not only be changed, but fixed as well. The spreader attachment sells for $100.
Once a tire has been remounted, it needs to be balanced. Docter sells a $200 precision bubble model and a $1,000 computerized, but hand spun, model where the operator uses a brake to stop it and back up to where a light flashes. He also sells a fully computerized, auto-spin and stop model for $1,500.
“We aren’t catering to the tire store that does 20 tires a day,” says Docter.
“Our customers do 30 to 40 tires a year. Getting a tire balanced at a shop can cost $10 each. Our precision bubble machine pays for itself with 20 tires.”
Docter says he’s selling machines to implement dealers and large farmers. In some cases, several farmers buy a machine together. In other cases, buyers have found themselves doing tires for neighbors.
The company also sells tire repair parts and supplies. A starter kit includes a buf-fer/scraper, rollers, patches and glue.
“It has everything you need,” he says.
“We also have a catalog with everything you need for professional tire repair.”
Contact: FARM SHOW Followup, Your Next Tire, Box 276, Firth, Neb. 68358 (ph 402 791-2004 or toll free 888 513-8473; [email protected]; www.yournext-tire.com).
“Our new magnetic wrench stops work great on bolts and nuts in hard-to-reach places,” says Carl Ernesti, Norfolk, Neb. The removable magnetic inserts contain a plastic collar, a rare earth magnet, and a hexagon-shaped base plate that keeps the magnet insert attached properly to the wrench. Wrench Stops fit open-end and box-end-type wrenches. They fit into the openings to hold bolts or nuts in place. They come in both standard and metric sizes. Ernesti, who grew up on a farm, says he has had his share of frustration with skinned knuckles, searching for dropped bolts and nuts and wrench slippage.
“The wrench always has good positive contact with nuts and bolts, so as you pull on the wrench it’ll stay in position without slipping. Wrench Stops also keep nuts and bolts from falling once they get loose,” says Ernesti.
“They work great in tight spots where it’s difficult to reach in with your hand. Wrench Stops also work good for starting bolts or nuts in hard-to-reach places.” Available in both standard and metric sizes and sold in a package with six different sizes. Standard sizes include 7/16, 1/2, 9/16, 5/8, 11/16, and 3/4 in. Metric sizes include 10 mm, 12 mm, 13 mm, 14 mm, 15 mm, and 18 mm. A single package of metric Wrench Stops or standard Wrench Stops sells for $24.95 plus S&H. Type in a promotional code: “FARM SHOW” for free shipping and handling. Contact: FARM SHOW Followup, C.J. Inventor, L.L.C., 116 East Phillip Ave., Norfolk, Neb. 68701 (ph 402 316-3149; [email protected]; www.wrenchstops.com).
Michael Horn of Rush, Ky., says he and his dad came up with a cheap way to fix badly damaged flat tires.
“My dad does custom bush hog work for people. The problem is, he runs over all kinds of things that can rip into a tractor tire.” To fix a flat, they bolt on heavy rubber patches inside the tire, between the tread and tube.
“We cut the patches out of 1⁄4-in. thick conveyor belt, making it slightly larger than the tear in the tire. Then we place the patch inside the tire and drill a series of 5/16-in. dia. holes through both the tire and patch, spacing them every 2 to 3 in. apart around the tear. We insert 1/4-in. bucket bolts with flat heads through the holes from the inside out, tightening the bolts down until the rubber patch puckers around the head of the bolt. We also put double nuts on each bolt and then batter the ends like a rivet so they won’t come out.
“Then we cut a large patch out of an inner tube and lay it inside over the bolts, then put enough air into a new tube to hold the tube patch in place. Once we finish putting the last side on the wheel rim we air up the tire to the proper pressure.” The two men say the last time they used this idea was three years ago when a radial tire on front of their tractor went flat.
“The tire is worn out now, but the rubber patch is still holding,” notes Michael. Contact: FARM SHOW Followup, Michael David Horn, 25023 Bolts Fork Rd., Rush, Ky. 41168 (ph 606 928-3153).
When Jim Remondi needed a new engine for his Case 1537 skid steer, he and Rich Comegys used an engine and parts from a Volkswagen Rabbit to replace the original 37-hp Wisconsin engine.
“We used mostly parts from the Rabbit to do the installation,” says Remondi.
“We did have to make an adapter for the VW flywheel. We bolted it to a shortened Rabbit CV joint with the other end bolted to the existing skid steer flange.”
Engine mounts were mostly modified from parts Remondi had laying around his shop. He also reports modifying the intake manifold to match available clearance on the skid steer.
“A turbo manifold would have worked without any modification,” notes Remondi.
The radiator was installed behind the seat. Cooling is provided by a 12-volt fan salvaged from a compact car. Remondi reports that biggest challenge came from revising the VW governor.
“We needed to convert it to constant speed,” he says.
“We kept trying different springs until we got it set where we wanted.”
Remondi reports that the project worked out better than he ever anticipated.
“The skid steer has plenty of power, and it is super economical,” he says.
Contact: FARM SHOW Followup, James Remondi, 4231 Sandy Bend Rd., Marydel, Deleware 19964 (ph 302 492-3724; [email protected]).