Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 20, No. 1 (1996)

Vol. 20, No. 1 (1996)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 30–31

25 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip 1 of 2

Gary Nielsen

Individual tip 1 of 2 from this reader’s published contribution.
Gary Nielsen, Pocahontas, Iowa

“Our company, Allied Precision Products (30 East Elm, Hwy. 3, P.O. Box A, Pocahontas, Iowa 50574; ph 800 803-3194 or 712 335-4250) makes products that improve performance of IH tractors. One is our hydraulic fluid filter extension kit that increases volume of fluid through the system. It was featured in FARM SHOW (Vol. 19, No. 4).

From the archive · Full text
Reader shop tip 2 of 2

Gary Nielsen

Individual tip 2 of 2 from this reader’s published contribution.
Gary Nielsen, Pocahontas, Iowa

“Now we’ve just unveiled a kit that converts IH tractors with 3-speed transmissions to 4-speed, giving them more versatility and performance than the day it came off the assembly line. Our kit consists of three pairs of parts. First, a new shaft and gear that install directly behind the torque amplifier. Second, a new quill housing and gear that also install directly behind the torque am-plifier. Third, new speed gears, which you can purchase from a salvage yard if you pre-fer, or that we’ll supply new. The conversion can take as little as a half a day. For IH 1566’s, 1586’s, 3788’s, and 6788’s. Kits start at $850.”

From the archive · Full text
Reader shop tip

Mark Yax

Mark Yax, Solon, Ohio

“I recently had to put a hole through a 12-in. hollow block for some pipe. Instead of using a chisel, I scribed a circle with a magic marker and nailed masonry nails to the circle at the 12, 3, 6, and 9 o’clock positions and then drove in as many nails as I could between them. Then with a light blow to the center, I made a very clean hole. I then did the same thing on the opposite side of the block. I made a nice clean hole in about 10 min.”

From the archive · Full text
Reader shop tip

Herman Vandehey

Herman Vandehey, 39595 N.W. Wilkesboro Rd., Banks, Ore. 97106 (ph 503 324-7573)

“We developed this ‘air guard’ oil drain pan and are now selling it for $99.95 post paid. The drain pan is 4 in.

deep with a 2-in. expanded steel platform above the base of the pan. The oil drains down into the pan and down the drain pipe. The pipe extends far enough into the drum so when oil reaches the bottom of the pipe it creates an air tight seal, no longer allowing oil to drain into the drum so you can take the pan off before the barrel overflows.

A small support rod on the opposite side from the drain helps stabilize the pan.”

From the archive · Full text
Reader shop tip

Steve Suter

Steve Suter, Altoona, Penn.

“When I recently had to take apart the front hub of my 1979 Ford F-250 4-WD pickup, a friend suggested that instead of buying the $35 wrench to take off the nut that I could make one out of a piece of 2 1/2-in. pipe. All I needed to do was cut four equally-spaced teeth into the end of the pipe. The problem was figuring how to get them in the right spots. I used a strip of non-corrugated cardboard as a template. I divided the cardboard strip evenly at four points and then drew in the teeth. Then I taped the template around the end of the pipe and used it as a cutting guide.

“Once the teeth are cut, you cut off the pipe at about 5 to 6 in. long. Then weld a small plate on the back end with a large nut welded to its center to give you something to use your torque wrench on when you re-assemble your hub. Works great.”

From the archive · Full text
Reader shop tip

Larry McWilliams

Larry McWilliams, Tulsa, Okla.

“I came up with a simple way to store pipe or lumber using old tires. Just suspend a pair of tires from the rafters of a shed or shop using wire, cable or rope. There are many different ways to use this idea.”

From the archive · Full text
Reader shop tip

Dana Dittbenner

Dana Dittbenner, Seaforth, Minn.

“I use a large, old dry chemical-type fire ex-tinguisher filled with gear lube to fill axle housings, etc., in hard-to-reach places. I replaced the pressure gauge at the top of the extinguisher with an air-fill pressure fitting so I can pump a few pounds of air into the tank to pressurize it. I screwed a barbed hose fitting into the nozzle fitting and attached a piece of rubber hose that makes it easy to reach with. You can install a valve or a small, bent piece of copper tubing at the end of the hose to prevent dripping when you shut it off. The top of the extinguisher screws off to fill with oil.”

From the archive · Full text
Reader shop tip 1 of 2

Robert Ingram

Individual tip 1 of 2 from this reader’s published contribution.
Robert Ingram, McArthur, Calif.

“We have an Allis Chalmers D-14 tractor that was originally equipped with a 6-volt positive ground electrical system which made it difficult to start. We always had to park it on a hill and roll it down to start it. I changed it over to 12-volt negative ground using a Delco/Remy alternator with an internal regulator. I put a 12-volt coil on it but used the original 6-volt starter. The points and condenser are the same ones that it had when it was running on the 6-volt system. It now has over 600 hr. on it since the conversion with absolutely no problems - except one.

It’s now hard to remember where we left it because it’s no longer parked in its usual spot on the hill. I wrote down the conversion step by step when it was fresh in my mind and if someone is considering a changeover, they can contact me (ph 916 336-6743).

From the archive · Full text
Reader shop tip 2 of 2

Robert Ingram

Individual tip 2 of 2 from this reader’s published contribution.
Robert Ingram, McArthur, Calif.

“I usually change my own oil in my vehicles and it was always hard to remember when the oil was changed last and what number the oil filter was. So now when I change oil and filter, I always scratch the date, mileage or hours and type of oil I used onto the oil filter. In my cars and pickup, I tear the lid off the oil filter box, write the same information on it, and store it in the glove box. When the next oil change is due, me, my wife, or children can take the box lid into the parts store and pick up the right filter every time.”

From the archive · Full text
Reader shop tip

Mike Lukenchuk

Mike Lukenchuk, Myrnam, Alberta

“When moving snow with a front-end loader, it’s difficult to keep the bucket from digging into the ground. To prevent the problem, I slit a piece of heavy-walled 2 1/ 2-in. dia. pipe and bolted it onto the blade of the bucket. It’s not necessary to have the pipe run across the full length of the blade. Once in place, the blade cannot dig into the ground yet will clear all the snow. The idea also works great for handling grain piled on the ground. Keeps the bucket out of the dirt and grain will slide up over the pipe and into the bucket.”

From the archive · Full text
Reader shop tip

Rick Mabeus

Rick Mabeus, Winfield, Iowa

“I was tired of always having funnels burp oil back at me instead of flowing right down so I came up with this idea for a ‘burpless funnel’. It works by simply allowing air to escape while you are pouring oil into the funnel, instead of getting the normal belch when air has to fight its way up through a funnel filled with oil. I simply ran a small piece of rubber tubing down along the side of the funnel. I made the tubing about the same length as the funnel and taped it to the side of it. Use the smallest diameter tubing you can find so you can still slip the funnel into the fill opening.

“I’m hoping to put a funnel like this on the market but you can make the modification to any existing funnel with a little tubing and tape.”

From the archive · Full text
Reader shop tip

Louis Vaessen

Louis Vaessen, Sublette, Ill.

“The final drives on each wheel of my Versatile 150 tractor would work the bolts out of the case, and break off the end of the floating axle. I fixed the problem by drilling the threads out of the case and putting in grade 8 bolts. Then I double-nutted them.”

From the archive · Full text
Reader shop tip

Dave Linstad

Dave Linstad, Porterfield, Wis.

“I’ve found that I can reduce damage to electric fences from deer running into them at night by fitting a 1-ft. length of spring off an over-head garage door opener on each end of the wire. Lets the wire give and then spring back.”

From the archive · Full text
Reader shop tip 1 of 2

Garth Luchterhand

Individual tip 1 of 2 from this reader’s published contribution.
Garth Luchterhand, Loyal, Wis.

“I’ve found that clear plastic cooking oil bottles make good containers for nails, screws, bolts, etc. They’re tough and you can see what’s in them.

From the archive · Full text
Reader shop tip 2 of 2

Garth Luchterhand

Individual tip 2 of 2 from this reader’s published contribution.
Garth Luchterhand, Loyal, Wis.

“My electric start snowblower has a rubber push button switch that gets stiff and won’t work when cold. I solved the problem by softening it up with an electric hair dryer.”

From the archive · Full text
Reader shop tip

Galen Vestal

Galen Vestal, Montesano, Wash.

“I was a heavy equipment mechanic for years and made this stud installer tool when I was working on the Alaska pipeline a few years ago. A lot of equipment there had planetary gears in the drive wheels. My stud installer lets me use an impact wrench to quickly set the stud. The stud won’t loosen when the installer nut is spun off. You simply weld an old discarded ball bearing into the nut, welding all the way around on one side of the stud (the studs are fine on one side and rough on the other side). Then screw the stud into the nut until it seats itself against the center of the bearing. The job ordinarily takes a long time to do by hand, but using an impact wrench saves a lot of time. When you reverse the nut it won’t suck the stud up out - it brings the nut off the end of the stud without bringing the stud up. With the ball bearing in the nut, the only surface area it’s touching is right on the end. I used this idea when I had a lot of broken 9/16-in. bolts on my front-end loader. I had to remove all of them and put in new ones. The only alternative is to screw on a double nut so tight that it could jimmy the threads or draw the stud back out and lose the torque value.”

From the archive · Full text
Reader shop tip

Howard L. Hutton

Howard L. Hutton, Norton, Texas

“One fairly tough repair I made was replacing the rear engine main seal and clutch in a 1980 Deere 4840 tractor. I first made a stand to support the engine portion of the tractor, mounting large bearings for wheels on a frame made with 1 1/4-in. threaded rod that makes it easy to raise or lower the engine half of the tractor. We installed three hydraulic jacks under the back half of the tractor and then securely blocked the rear wheels in the front and back and on both sides so they could not move in any direction. Then we rolled the front half of the tractor forward about 3 ft. and did the work. We then pushed the two halves back together. We only had to push the front half to the side about 1/2 in. to get a perfect fit. We then put the bolts back in place with no other adjustment. Works fine and we saved a lot of money.”

From the archive · Full text
Reader shop tip

David W. Hunt

David W. Hunt, Abernathy, Texas

“I use sections of road grader blade to rebuild the points on my subsoiler. I hard surface the sections of blade before installing them on my ripper. These points last as long or longer than store-bought. What’s more I can usually get the sections of grader blade free from our local highway maintenance garage.”

From the archive · Full text
Reader shop tip

Jeff Vackiner

Jeff Vackiner, Cody, Neb.

“A neighbor gave me a tool many years ago that pushes the bottom back through ear tags on calves, thus saving the ear tag and button for reuse. It worked so well, I simplified the design and now manufacture the tool. After being taken out, buttons are washed and dis-infected before being used again. They will last many years and you can tell at a glance when they should be replaced. My ‘detagging’ pliers sells for $15 plus $3 S&H, and should last a lifetime. Contact me at HC 77, Box 10, Cody, Neb. 69211 (ph 800 636-7446 or 402 823-4048).

From the archive · Full text
Reader shop tip

R. George

R. George, Gowrie, Iowa

“I’ve found that one of the most useful things you can do is keep all pictures and literature on your equipment on file somewhere close-by at hand to keep parts numbers, sizes, and other important information at your fingertips. It makes repairs much easier. I also keep information on repairs and add-ons with each file.”

From the archive · Full text
Reader shop tip

William E. Craycraft

William E. Craycraft, Bloomingdale, Ind.

He rigged up a simple oiler for the chain at the top of his grain bin auger.

“During the fall harvest season, I am usually in the combine so I’m not back at the bin to keep an eye on things. The result was that often the chain on the unloading auger did not get oiled enough by the help unloading trucks. So I came up with this way to make it easy to oil the chain from the ground. I used a chain lube spray can, an old grease gun holding clamp, two small bolts, a short bar to act as a lever on the spray nozzle, a long nylon cord, and a small spring to support the weight of the cord. It was a simple matter of mounting the can in a position where the spray would hit the chain and running the cord down to the ground. Now just a short pull on the cord from the ground oils the chain. We don’t have to climb up on the bin and wear and tear are kept to a minimum.”

Shop feature stories

From the archive · Full text
Feature story

Oregon Company Specializes In Repair Of PTO’s

Featured source:

If you have a damaged pto shaft that needs parts or if you need an entire new driveline, an Oregon company may have just what you need. Driveline Service of Portland, Ore., specializes in the repair and manufacture of pto drivelines and supplies parts for the four manufacturers that build nearly all the pto drives in the U.S. It purchased all the inventory of driveshafts and parts from Rockwell International when that company left the agricultural business in the late 1980’s.

“We have the largest inventory of agricultural pto driveshaft parts in the U.S. and can service any pto shaft that’s ever been made,” says Tom Watt, ag specialist.

“We supply everyone from original equipment manufacturers to implement dealers to farmers. Most dealers don’t stock a lot of pto parts so they have to order them from original equipment manufacturers, which can result in a time lag of several weeks. When farmers call us, we ship the parts right away by UPS. We also save you money. In most cases, the prices charged by equipment manufacturers are somewhat inflated. We can beat their rates by quite a bit.” Contact: FARM SHOW Followup, Driveline Service of Portland, 9041 N.E. Vancouver Way, Portland, Ore. 97211 (ph 800 227-8608).

From the archive · Full text
Feature story

U-Joint Puller For PTO Shafts

Featured source:

This new U-joint puller for pto driveshafts lets you remove bearing cups quickly and easily without damaging the driveshaft, yokes, cups, or bearings, says Tiger Tool International, Inc., Sumas, Wash.

The “Tiger” U-joint puller is equipped with a threaded bolt on top and a pair of steel “legs” that mount on the driveline or on the U-joint cross. To remove bearing cups (even those that are rusted), slip the U-joint puller over the yoke and turn the bolt to press the cup out (you can catch the ejected bearing cup with your free hand). Repeat the process on the remaining three sides of the yoke.

The puller is available in three models: Mark I to fit driveline series 1500 - 1800 commonly found on big trucks; Mark II for 1500 and under series drivelines such as those on intermediate trucks; and Mark III for cars and pickups.

The Mark 1 model sells for $380, Mark 2 for $195, and Mark III for $125. Contact: FARM SHOW Followup, Tiger Tool International, Inc., 377 West 2nd St., Sumas, Wash. 98295 (ph 800 661 4661; fax 604 859-3977).

From the archive · Full text
Feature story

Rolling Platform Makes It Easy To Service Big Equipment

Featured source:

“Our new portable platform makes it easy and safe to work on big machinery,” says Rodney Koser, Elbow Lake, Minn.

The 4-wheeled unit consists of a steel platform that rides up or down on a 9-ft. high steel mast, a manual winch that’s used to raise or lower the platform, and a 2-part folding ladder that stores on the platform. You fold the ladder down, then crank up the platform and set brakes on the back tires and climb up the ladder onto the platform. The unit rides on a pair of 18-in. tires in back and small caster wheels in front.

“It’s a lot safer than trying to make a platform out of barrels and planks or using a front-end loader,” says Koser.

“You can use it to work on combine engines, big 4-WD tractors, etc. - anything where you need to get up high off the ground. It’s small enough that you can also use it inside shop buildings. The platform automatically locks onto latches spaced 1 ft. apart on the mast. It has a removable tongue that pins onto the frame just behind the caster wheels so you can tow it like a trailer behind a pickup, with the caster wheels off the ground.

“It’s not designed to move people up or down. If you want to adjust the platform height you have to climb down off the platform and operate the winch, then climb back on.”

Sells for $1,195. Contact: FARM SHOW Followup, Koser’s Inc., Elbow Lake, Minn. 56531 (ph 612 677-2497).

From the archive · Full text
Feature story

Handy “Multi-Use” Shop Tool

Featured source:

You can do a lot of different jobs with this handy new shop tool that comes in three separate pieces that snap together for storage and carrying. The “Wrench-All” consists of a socket wrench, nail puller bar, and adjustable wrench equipped with a ball peen hammerhead. By holding the wrench in one hand and the nail puller bar in the other hand, you can use it as a screwdriver, allen wrench, or lug wrench. A socket carrying attachment snaps onto the nail puller bar, which is attached to the wrench by fitting the nail puller’s cap over the ball peen hammerhead on the wrench. Two models are available - a 10-in. model accepting 3/8-in. drive sockets that sells for $32 and a 12-in. model accepting 1/2-in. sockets that sells for $36. Socket attachments are not included. Contact: FARM SHOW Followup, Birkworks, Inc., 919 Frank S.E., Huron, S. Dak. 57350 (ph 605 353-1657).