Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 23, No. 5 (1999)

Vol. 23, No. 5 (1999)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 38–41

31 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Grant Strong

Grant Strong, Wabash, Ind.

“I mounted a box on the right rear fender of my MTD riding mower to carry tools, trash cans, a hand trimmer for low limbs, a hook for picking up fallen small limbs from the ground, etc. It’s just a corrugated box glued to a piece of carpeting. I drilled a 1/4-in. dia. hole in the fender and bolted it on using a strip of 1 1/2-in. wide strap iron.”

From the archive · Full text
Reader shop tip 1 of 2

Ken Schmitz

Individual tip 1 of 2 from this reader’s published contribution.
Ken Schmitz, Fond du Lac, Wis.

“I bought a used Westendorf loader at an auction. It had been mounted on a Massey tractor equipped with dual hydraulic outlets. However, I wanted to use it on a Massey Ferguson tractor that has only one hydraulic outlet. To solve the problem I made my own single lever hydraulic joystick out of a used two-lever Deere valve that had been used on a small utility tractor. The joystick is mounted on a length of sq. steel tubing that’s permanently mounted on the right tractor fender next to the steering wheel. When I don’t have the loader on I uncouple the hydraulic hoses, then loosen one set screw and slide the joy-stick forward out of the way so that I can use the tractor’s original controls. The joystick stays on the tractor but is out of the way.

From the archive · Full text
Reader shop tip 2 of 2

Ken Schmitz

Individual tip 2 of 2 from this reader’s published contribution.
Ken Schmitz, Fond du Lac, Wis.

“Here’s another idea. My Deere 336 small square baler has a narrow pickup which sometimes make it hard to get the entire windrow, especially if wind scatters the hay out. I solved the problem by making my own converging wheel out of an old 30-in. disc blade and mounting it on the right side of the pickup. I bolted pairs of Deere rake teeth to the outside of the blade and mounted it on a spring-loaded arm. I bent the teeth so that as they go around they release the hay into the pickup. Commercial converging wheels for round balers are expensive and sell for about $300.”

From the archive · Full text
Reader shop tip

Gary Lantz

Gary Lantz, Augusta, Ill.

“I came up with a way to automatically start and stop the auger at my bin when unloading grain that I haul in from the field during harvest. I connected a mercury switch to a pair of 12-volt solenoids and also to a spring-loaded paddle that mounts in the auger hopper. One solenoid turns the tractor pto on and off and the other one operates the tractor throttle. As soon as grain hits the switch it automatically speeds the tractor up and also turns the pto on. When grain no longer hits the switch the pto automatically turns the pto off and slows the tractor back down to an idle. I can haul in wagon loads of grain and unload them by myself all day long.”

From the archive · Full text
Reader shop tip

Bill Reeks

Bill Reeks, Cromwell, Ky.

“Here’s how I sharpen the blades on my riding mower without removing the mower deck or blades.

An eye bolt is permanently installed in the front end of the Cub Cadet. I attach that to an overhead chain hoist and lift. Once the tractor is up, I put a safety stand under the deck and lock the rear wheels to keep the tractor from moving once it’s raised. I use a small 4 1/2-in. hand grinder, which I bought out of a mail order catalog, to sharpen the blades. This method is much quicker and easier than detaching the deck.”

From the archive · Full text
Reader shop tip

Fred Hansen

Fred Hansen, Santa Rosa, Calif.

“To salvage spray tanks with worn-out agitator bearings, I’ve found I can convert them to liquid ‘sparge’ agitation by boring out the forward agitator bearing so it can be tapped and fitted with a pipe. You have to screw pipe into both sides of the bearing. Then I just run plumbing to the fittings attached to the bearing. You have to plug up the rear bearing. This procedure has worked quite well on two sprayers using Tee-Jet and Hy-Pro venturi agitators and eductors.”

From the archive · Full text
Reader shop tip

R.E. Charlton, Jr.

R.E. Charlton, Jr., Dillwyn, Va.

Here’s a time-saver I came up with that makes tire repair easier. I screwed a valve stem core remover onto the end of a ballpoint pen and then put several new valve cores inside. It keeps them handy and you can carry it in your shirt.”

From the archive · Full text
Reader shop tip

Mike Hanley

Mike Hanley, Cashton, Wis.

“I’ve got a totally rebuilt 1949 Willys CJ-2 jeep. Nearly everything on this jeep has been replaced or rebuilt and it runs great. I use it instead of an ATV. What I like is that I can take it to town for parts or coffee, something I can’t do with a conventional ATV.

“Here’s a tip: You can get any part for a 1941 to 1965 Civilian or Military jeep at: Willys Mpls., 301 Pine Street, Farmington, MN 55024 ph 651-460-8888. This outfit should get a blue ribbon for outstanding service.”

From the archive · Full text
Reader shop tip

Dick Thompson

Dick Thompson, Boone, Iowa

“We stopped leaks from our Gehl 322 slurry spreader on the highway during transport by bolting a 3-in. wide, 1/2-in. thick strip of rubber belting to the bottom of the unloading chute.

“I get a lot of sludge from a local city which dumps the material into a hillside bunker. Some of the sludge is quite liquid and tended to leak out the unloading chute whenever I drove the spreader on the highway. The spreader isn’t designed for liquid manure and so I came up with this idea. The spreader’s slide gate fits tight against the belt, yet the rubber flexes enough to make a nice, tight fit.”

From the archive · Full text
Reader shop tip

Dale Conrady

Dale Conrady, Hettick, Ill.

He made his own wooden gun vise that cradles a shotgun or rifle for cleaning and maintenance or to make test firings and precise sight adjustments.

A 3-ft. long 2 by 6 forms the base of the unit. There’s a V-shaped upright at one end to hold the barrel and a vise at the other end that clamps down on the stock. The vise consists of one stationary wood block and a moveable block that’s held to the base by a door hinge. It clamps down on the gun by tightening a wing nut on a bolt that runs through both blocks.

All parts of the vise that touch the gun are covered by strips of carpeting to avoid scratches.

From the archive · Full text
Reader shop tip

Clair & Warren Wilson

Clair & Warren Wilson, Winchester, Ill.

All with their sons, Clair and Warren are well-known locally for their ability to tackle just about any repair job in their well-equipped farm shop. That means they have a lot of tools, including sets of king-size wrenches for big jobs. Moving tools around the shop and across the farm yard was difficult until they built this 3-wheel cart fitted with car wheels.

The big automotive tires roll easily across uneven terrain. The frame of the cart is built heavy, with plenty of storage drawers for all kinds of tools. An A-shaped tool holder on top holds the biggest wrenches.

The up-front caster wheel is steered by a pull handle off a toy wagon.

From the archive · Full text
Reader shop tip

Howard Vogel

Howard Vogel, Waverly, Iowa

“After looking at various commercial chop saws, I reached three conclusions: They weren’t built heavy enough, they didn’t cut angles with the accuracy I required, and I couldn’t jus-tify the expense.

“So I built my own chop saw that’ll cut 100 percent accurately at virtually any angle and will go through anything. For instance, I once cut a crankshaft from an old Volkswagen car for a man who had tried unsuccessfully to cut it with a power hacksaw.

“My chop saw is fitted with industrial strength, high-speed, 14-in. dia. blades and is powered by a 1 hp motor off an old milk-ing machine. It’s rewired for 110 volts instead of 220. The saw mounts on a piece of 1 by 6 with a saw arbor mounted on the opposite end. The platform-mounted motor and arbor mount on a 5/8-in. dia. rod that runs across the back of my work bench. This allows me to slide the saw left or right of the vise on front of the bench. The vise bolts to a plywood disc that rotates and is marked off in degree increments that let me know exactly what angle I’m cutting.

“Works better than any commercial unit I know of and didn’t cost more than $20 to build.”

From the archive · Full text
Reader shop tip 1 of 3

Tom Dutton

Individual tip 1 of 3 from this reader’s published contribution.
Tom Dutton, Menoken, N. Dak.

Tom came up with these inventions to make life easier around his farm.

“I made a folding, four-legged portable vise stand from scrap 1 1/2-in. sq. tubing. I made a hinge for the top of the folding frame out of 3/4-in. sq. tubing and 1/2-in. dia. round bar. The stand holds the vise about waist high. It stores easily and is exceptionally stable.

From the archive · Full text
Reader shop tip 2 of 3

Tom Dutton

Individual tip 2 of 3 from this reader’s published contribution.
Tom Dutton, Menoken, N. Dak.

“I made a bin auger from an old 6-in. dia. auger that had a worn out tube. I used two small U-joints from an old front-wheel drive car to make the upward joint in the auger just outside the bin. Drive is provided by an orbital motor off an old drag auger.

From the archive · Full text
Reader shop tip 3 of 3

Tom Dutton

Individual tip 3 of 3 from this reader’s published contribution.
Tom Dutton, Menoken, N. Dak.

“I also made a baler pickup lift to reduce the number of teeth we break. It’s made from an old hydraulic cylinder and scrap iron bolted to the frame of our OMC baler. We bolted a short piece of chain to the original lift spot on the pickup so it can flex freely. The modification saves us a lot of money in broken teeth.”

From the archive · Full text
Reader shop tip

E & K Ag Products

E & K Ag Products, HCR 3, Box 905, Gainesville, Mo. 65655 (ph 417 679-3530)

“Our new sleeve puller is designed to remove or install even the tightest sleeves. It’s made of rustproof steel and equipped with a 1-in.

dia. center screw rod. It also comes with six discs.

“To use it you put two 1/2-in. thick discs and two nuts on the bottom of the rod, then run the rod up through the top and slide a bridge on. After installing a heavy-duty ball thrust bearing on the top of the bridge you use a wrench to screw the nut down on the bearing. Then hold it up and set two 5-in. long blocks (supplied) under the bridge to make room for the sleeve to come up. The bearing keeps the nut from binding for easy turning and fast removal.”

From the archive · Full text
Reader shop tip

Merle Black

Merle Black, Valencia, Pa.

“Anyone who owns a Gravely walk-behind, rope-start mower knows how hard it is to start them. The problem is that you’re pulling against compression inside the engine which makes it hard to turn over. I solved the problem by installing a compression release valve made by Stihl Co. The company equips its bigger chain saw models with these valves to make them easier to start.

“To install the valve I drill a 3/8-in. dia. hole above the exhaust valve and all the way through the head, then use a metric tap to make threads in the hole and screw the valve in. Pushing a button on the valve releases pressure in the cylinder and makes the engine easier to turn over when you pull on the rope. Once the engine starts, the valve automatically closes.

“The hole above the exhaust valve prevents any change in the mixture of fuel as it comes in from the intake side of the carburetor. Stihl doesn’t keep these valves in stock, but you can order them from the company. Before installing the valve I first used a grinder to remove the fins that cool the engine, providing me with room to drill the hole.”

From the archive · Full text
Reader shop tip

Norman Smith

Norman Smith, Walsh, Ill.

“I used part of an old hydraulic cylinder shaft to make an inexpensive, heavy hammer. The shaft had been accidentally bent. I cut off a length of the shaft and burned a hole through it. I used a length of sq. steel tubing to make the handle and butted the two pieces together, then ran a bolt through the shaft and tubing and fastened a nut to the bottom of the bolt.”

From the archive · Full text
Reader shop tip

Terry Therkilsen

Terry Therkilsen, Comfrey, Minn.

“This home-built bulk oil dispenser is as handy to use as any commercial system I’ve seen. I made it for a local mechanic who had re-cently built a new shop. It consists of six 102-gal. tanks made out of 12 ga. sheet metal.

The entire tank is 11 ft. wide, 3 ft. high, and 2 ft. deep. I divided it into six interior compartments, then made a frame out of angle iron to mount the tank about 5 ft. high. Each compartment is fitted with a tap at the bottom. A clear plastic sight gauge on each compartment lets you see at a glance how much oil is left. Oil gravity flows out of each tank through steel lines equipped with ball valves.

“Vertical fill lines mount on the right side of the tank, allowing a pump to suck oil out of a 50-gal. barrel in order to fill the tanks. Works great for oil changes.”

From the archive · Full text
Reader shop tip

Bruce Lowery

Bruce Lowery, Spotsylvania, Va.

“If you’re fed up with tripping over extension cords in your shop, get several surface-mounted electrical boxes, install receptacles, and hang them from the ceiling in your shop at various locations high enough to clear your head. Then when you need to plug in a tool a receptacle will always be close by.”

From the archive · Full text
Reader shop tip

Larry Kluckner

Larry Kluckner, Longdale, Okla.

“I harvest rye and vetch for seed with a 1960’s C Gleaner combine with 16-ft. header. I’ve always had trouble with the crop wrapping on the end of the reel shaft at each end. This would lock up the reel and cause the belt to slip so the crop wouldn’t feed properly.

“A neighbor came up with a solution based on some older combines, like Masseys, that didn’t have open-ended reels. We simply attached a round piece of light gauge sheet metal, approximately the thickness of the reel bats, to the ends of the reel. We screwed a piece of angle iron, which acts as a mounting bracket, to the end of each bat with self-tapping metal screws. We then took off the bushing that the reel shaft rotates in and screwed the sheet metal, which overlaps the end of the reel bat by about 1/2 in., to the brackets.

“We did this two seasons ago and it totally solved the wrapping problem. It didn’t cost anything since all the materials were scrap. This would work on any combine that doesn’t have an open end on the reel.”

From the archive · Full text
Reader shop tip

Virgil W. Russell

Virgil W. Russell, Bloomingdale, Ohio

“The rubber rollers on my Deere 1207 mower conditioner went bad and the price of a new one was more than the machine was worth. We made our own repair by cleaning the rollers down to he bare metal and welded 1-in. square bars to them, making a crimper that works just fine. A cheap repair that actually paid off for us.”

Shop feature stories

From the archive · Full text
Feature story

“Locking Pliers” Helps Unbolt Cultivator Sweeps

Featured source:

If you’ve ever scraped skin off your fingers trying to remove rusted or corroded bolts on cultivator sweeps, chisel plow points, etc., you’ll understand what prompted Gene Klann of Stewartville, Minn., to invent a new kind of “locking pliers”.

The “Farmer’s Friend” locking pliers work like modified vice grips. One jaw is fitted with a U-shaped “fork” that is placed against the back side of the shovel, around the nut. It leaves enough room to get a socket on the nut. The other jaw has a pointed end that’s used to hold the bolt head in the square recess and keep it from coming out.

“It eliminates the need to weld the bolt head, cut off the nut with a torch, or grind off the nut so the bolt can be removed,” says Klann.

“I got the idea one day while helping a neighbor change the shovels on his field cultivator. He was using an impact wrench and I used my fingers to try to hold a bolt head in. That was a big mistake because I cut my finger bad.”

Klann is looking for a manufacturer. Contact: FARM SHOW Followup, Gene Klann, 2900 Cty. Rd. 6 S.W., Stewartville, Minn. 55976 (ph 507 533-8543).

From the archive · Full text
Feature story

“Infinitely Adjustable” Jack Stand Filled With Steel Shot

Featured source:

“Our new-style jack stand uses steel shot instead of pins to set the height so there’s no danger of a pin shearing. Another advantage is that you can set the stand at exactly the desired height anywhere, from 13 3/4 to 20 1/2 inches,” says Cameron Klasson, S.A.E.F. Finishing & Fabrication, Gentry, Ark.

The 6-ton jack stands consist of a chrome “neck” inside a hollow steel cylinder. As you pull the neck up to the desired position shot flows from the neck into the base, forming a solid mass of steel under the neck. To reset the jack stand, you simply turn it upside down so shot flows back into the neck.

“The only way the jackstand will go down is if you tip it upside down,” says Klasson.

“The stand will safely support loads up to 25,000 lbs. It comes with a powder coated finish.”

The jack stand is sold in pairs for $79 per pair plus $12 S&H.

Contact: FARM SHOW Followup, S.A.E.F. Finishing & Fabrication, 19058 Jackson Rd., Gentry, Ark. 72734 (ph 501 736-4659).

From the archive · Full text
Feature story

Innovative Hub Fix Using Helicoil Inserts

Featured source:

When the threads got stripped on a pair of Deere 8820 planetary drives, Marvin Gorden knew he either had to shell out for some expensive replacement drives, or find a way to retap the threads. He decided on the latter solution but that required some innovative, seat-of-his-pants engineering.

The problem was drilling out existing holes in the hubs and then tapping for new bolts. To work, the holes would have to be absolutely straight. And the only way he could think of to do that was to make a jig.

He used aluminum bar stock but notes that you could also use steel. He cut the aluminum into four pieces and welded them together into a hexagonal frame. Then he got exact measurements from the center of the hub to each bolt hole, and took the jig to a machine shop with a CNC mill (very common nowadays, he says). The shop then drilled the 10 holes to spec.

Gorden inserted stainless steel sleeves into four of the holes to guide the drill bits because the bits would have chewed up the aluminum. He uses four bolts to hold the jig to the hub. He then drills and taps holes, and then rotates the jig to drill the rest of the holes.

Once all the holes are drilled and tapped, he removes the jig and inserts helicoil inserts.

These stainless steel inserts create permanent, strong threads better than anything you can make by tapping a hole. You just drill the hole out slightly larger than you need and screw in the Helicoil inserts. (For more information on these, contact: Emhart, Heli-Coil, 510 River Rd., Shelton, Ct. 06484 ph 203 924-9341).

“This jig cost me $250 to make but it was worth it and the repaired hub is like new. So far I have replaced the threads in four wheel hubs,” he notes.

Gorden is also inventor of Gorden Rotor bars for Case-IH specialty rotors and he runs a popular “combine talk” web site, www.Harvesting.com.

Contact: FARM SHOW Followup, Marvin Gorden, Gorden Harvesting & Equipment, P.O. Box 12783, Wichita, Kan. 67277 (ph 800-745-1680).

From the archive · Full text
Feature story

Make Repairs Under Vehicle Without Laying On Your Back

By By Mick Lane
Featured source:

If you’re tired of dirt and sparks in your face while working underneath pickups and cars, Accessible Systems, Inc, Jonesborough, Tenn., has a possible solution.

The Easy Tilter fastens to the wheel hubs and allows you to quickly and effortlessly roll any vehicle onto its side. It’ll handle up to 6,000 lbs.

Rolling a vehicle onto its side with the Easy Tilter usually takes an hour or less, according to Joel Johnson, owner of Accessible Systems and designer of the Easy Tilter.

“I developed it because many auto shops and especially hobbyists are limited in space. Competitive tilters — and I used to sell one brand — required two car bays to work. The Easy Tilter works in just one,” Johnson says.

Johnson began developing his tilter in 1996. After a year of so of experimentation he landed on the current design. His tilter has two-wheeled carriage assemblies that allow the vehicle to roll toward the jack as one side is lifted up. This keeps the vehicle within one car bay as it rotates up on its side. He expects to receive a patent shortly on the concept.

“Because the jack doesn’t need to move, you can use an overhead chain fall or engine hoist instead and save the price of the jack if you wish,” Johnson says.

“This isn’t possible with other designs.”

Johnson says his Easy Tilter is much heavier in construction than competing units.

To use the Easy Tilter, remove the wheels from one side of the vehicle and attach the tilting frame to the hubs using the mounting plates that come with the tilter. (You’ll need to order 4-, 5- or 6-hole mounting plates, according to the style of your vehicle. If you need more than one set, it will cost extra.) The next step is to remove the wheels from the other side and attach the lift wheel plate to the hub at the heaviest end of the vehicle (usually the front). The jack (or whatever lift you’re using) attaches to the lift plate. Then all you do is raise the jack or lift.

As the side of the vehicle raises, the other side rolls toward the jack. As it nears the center of gravity, it rolls onto the second set of carriage wheels and comes to rest safely on its side. The jack or lift attachment can be removed once the vehicle is on its side.

To lower the vehicle, reattach the jack or lift. Then, using a special bracket on the carriage, a floor jack can be used to raise the carriage and vehicle back past its center of gravity and onto the jack so it can be lowered to the floor.

The Easy Tilter is priced at $499. Optional jack for the Easy Tilter is around $450. Both Easy Tilter and its optional jack weigh around 225 lbs. each. If you’re interested in an automotive lift but feel the one shown might not be quite what you need, Johnson wi’ll be happy to talk to you about special adaptations for farm equipment or oversized vehicles. He makes a variety of other systems, including one that rotates a vehicle 360°.

Contact FARMSHOW Followup, Accessible Systems, 440 Matson Road, Jonesborough, Tenn. 37659 (ph 423 975-8907; fax: 423 975-8908; Website: www.accessiblesystems.com.

From the archive · Full text
Feature story

Elevated Air Compressor Saves Shop Space

Featured source:

“We needed more floor and wall space in our shop so we mounted our air compressor up out of the way, 10 ft. off the floor,” says Ken Brecht, Moorcroft, Wyo., who built a heavy steel platform to hold the compressor.

Brecht installed a new electric junction box 10 ft. up the wall.

“Mounting the compressor up high keeps the air intake out of the dust and also reduces some of the compressor noise when it’s running,” says Brecht.

“We keep a parts washing tank under the compressor. It’s a better use of the space.”

Contact: FARM SHOW Followup, Ken Brecht, 353 A McKean Rd., Moorcroft, Wyo. 82721 (ph 307 756-9309).

From the archive · Full text
Feature story

Home-Built Electric-Powered Sheet Metal Roller

Featured source:

“We saved a lot of money by building our own portable, electric-powered sheet metal roller that works as well or better than a commercial unit,” says Joel Waldner, Lethbridge, Alberta.

The unit is equipped with three 8-in. dia., 50-in. long steel rollers – two at the bottom that are chain-driven by a 2 hp electric motor, and one on top that can be adjusted up or down by turning a handle attached to a threaded rod at either end of the unit. The motor is equipped with a forward and reverse switch, allowing the two bottom rollers to be reversed. Three shorter rollers extend out one side of the unit. The two bottom ones are grooved which makes it easy to bend steel rods into a circle. The short rollers can be slipped on and off the shafts that support each roller.

The metal bender mounts on four caster wheels so it can be rolled around the shop.

“It works great for bending panels of 48-in. wide sheet metal,” says Waldner.

“To make the rollers we bought 3 1/2-in. dia. solid steel shafts and lathed them down to a 3-in. diameter. We used sq. tubing to make the frame.”

Contact: FARM SHOW Followup, Joel Waldner, 67 Tudor Crescent, Lethbridge, Alberta, Canada T1K 5C7.

From the archive · Full text
Feature story

“Lazy Susan” Iron Rack

Featured source:

“My ‘Lazy Susan’ iron rack is a real time and space saver in our welding shop,” says Richard Imhof, Ruthton, Minn., who uses the rack to store lengths of angle iron and steel pipe up to 10 ft. long. The unit consists of a round rotating base divided into four sec-tions. Imhof can access any piece of steel by simply swiveling the rack.

To make the rack he used the rear wheel hub and axle from a Chevy 3/4-ton pickup and the flywheel off a Gehl silage chopper. He cut off the axle about 1 in. from the hub and welded it to a 2-ft. sq., 3/8-in. thick steel plate that bolts to the floor. Then he bolted the flywheel to the hub, using 4 bolts. Then he bolted the axle upside down to the flywheel. He placed a long steel pipe over the axle and welded 12-ga. sheet metal uprights from the flywheel to the pipe to divide the rack into six sections. He also used bent steel rod to make a circular top support and short lengths of steel rod to make a middle support.

“It works great for storing scrap steel less than 10 ft. long. I used to throw such pieces up against a corner of the building and ended up with such a mess that I often couldn’t get at the piece I wanted. Now to get the piece of steel I want I just swivel the rack.”

Imhof used the same type of swivel base to build a 6-ft. high, 3-ft. sq.

“honeycomb” storage rack with 8 by 6-in. compartments. There are four compartments per row on each side of the rack. The rows are staggered, allowing the “north-south” and “east-west” compartments to go all the way through on alternating levels.

“I’ve got at least three tons of iron stored in this rack, including about 1,000 lbs. of welding rods inside boxes that I keep on top of the rack,” says Imhof.

Contact: FARM SHOW Followup, Richard Imhof, Rt. 1, Ruthton, Minn. 56170 (ph 507 658-3366).

From the archive · Full text
Feature story

More On Starting Older Deere Diesels

Featured source:

“I read with interest the story on starter problems with Deere 2-cyl. diesels in the last issue of FARM SHOW,” says Mike Hanley, Cashton, Wis.

“We have two Deere 730 diesels. The problem I had was with the internal ground on the 24-volt system. Any nick in any wiring would fry the whole system.

“The guy in your story was offering an add-on starter kit for $835 that converted the tractors to 12-volt. I had my 24-volt starters rebuilt to 12 volt at a cost of $270 each and added rebuilt GM 12-volt alternators wired for single wire for $65 each.

“As I understand it, there’s a Deere 12-volt starter built for a piece of industrial equipment which has an armature and fields that fit into the late style starter motor casing of the 730. Deere had two starters for the 720 and 730. This conversion only works for the later style (JD #11073R – Delco Remy #1113830).

“The key is how to wire it. One of my 730’s still has the four 6-volt batteries. The other has two 12-volt batteries. I wired in a “jumper solenoid” at the main solenoid. It came off an old Ford truck but a new one costs just $5. By doing this, the hot juice goes the shortest way possible from batteries to starter instead of batteries to dash to starter.

“The 24-volt system has two battery cables running from battery to starter. One’s hot, the other is the internal ground. On the 12-volt system you leave both cables but wire them both hot and add a short ground to the frame. The two cables double the carrying capacity from batteries to starter.

“The only problem with this system is that if the tractor is laid up for a month or so, you should disconnect the ground at the batteries as the single wire alternator system will drain the batteries over time.

“I worked with J.G. Rebuilder & Supply, 1039 Czech Ave., Friendship, Wis. 53934 (ph 608 339-6580). They did the rebuilding on the starters.”

Contact: FARM SHOW Followup, Mike Hanley, 26054 Mariner Rd., Cashton, Wis. 54619 (ph 608 654-5417).

From the archive · Full text
Feature story

Homemade “Shovel Rack” Keeps Tillage Shovels Organized

Featured source:

“Our homemade ‘shovel racks’ work great to store shovels off field cultivators and plows. The racks keep the shovels up off the floor so they stay clean and out of the way,” says Joel Waldner, Lethbridge, Alberta.

Waldner is a member of a Hutterite colony with a large farm operation. Since they farm several thousand acres they go through a lot of shovels, buying about 600 new ones every year. Each rack can store up to 150 shovels so they made four of the racks.

Each 6 1/2-ft. high rack consists of a drill stem pipe welded onto a disc blade that serves as the base. A series of 16-in. long, 3/4-in. dia. rods spaced 1 ft. apart are welded to the sides of the pipe. The shovels simply slip over the rods.

Contact: FARM SHOW Followup, Joel Waldner, 67 Tudor Crescent, Lethbridge, Alberta, Canada T1K 5C7.