Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW
Issues / Vol. 32, No. 5 (2008)

Vol. 32, No. 5 (2008)

Money-Saving Repairs & Maintenance Shortcuts · Printed section pp. 36–39

30 selected entries · Complete text of selected entries

This issue’s section includes reader tips and feature-length shop stories. Held items and editorial notices are not reproduced.

Archive text: prices, coupons, availability and contact details reflect the original publication, not current offers. Reader methods are not universal instructions; follow manufacturer guidance and proper safety practices.

Reader shop tips

From the archive · Full text
Reader shop tip

Charlie Fee

Charlie Fee, Zearing, Iowa

Charlie says his garden hoe is always sharp because he parks a pedal-powered emery wheel near the path to the garden. He puts an edge on the hoe as he heads out to chop weeds.

From the archive · Full text
Reader shop tip

C.F. Marley

C.F. Marley, Nokomis, Ill.

“When the check valve got stuck in the open position at the bottom of our old dug farm well, we were facing a major amount of work to dig down alongside to install a new suction line. Fortunately, the service man who came out to the farm had a simpler solution. He had seen the problem before and just installed a new check valve in the line up by the pump leading down to the old suction line. It solved the problem. The check valve at the bottom of the well just stays open.”

From the archive · Full text
Reader shop tip

John Marley

John Marley, Athens, Ill.

This homemade dispenser for electric cable really saves time and effort. It consists of a piece of plywood with a bottomless gallon can bolted to the center of it. The plywood and can hang from the ceiling by a chain that attaches to the center of the board. A roll of electric cable is placed on the board around the can. You can pull off any amount of cable and chain will just keep twisting as needed. Once you cut off the cable, the chain spins back around.

From the archive · Full text
Reader shop tip

Jimmie Taylor

Jimmie Taylor, Fairfield, Ill.

“I have an Allis Chalmers 912 lawn tractor with a 4-ft. tiller on it. I was having trouble with the 3-pt. lift on back so I put a small 12-volt winch on it. Works fine now and it was an easy change to make. I tried the same idea on another small tractor and it worked well, too.”

From the archive · Full text
Reader shop tip

Donald Bunch

Donald Bunch, Aberdeen, Miss.

“I do a lot of welding of small parts and sometimes I need a third or fourth hand. That’s why I made this ‘third hand’ device from a locking pliers and scrap metal. Sure works well. I made it out of 3/16 by 1/2-in. flat bar, with bolts welded into each hinge point with hand-tightened wing nuts.”

From the archive · Full text
Reader shop tip

Bill Reeks

Bill Reeks, Cromwell, Ky.

“Military ammo boxes are ideal for tool boxes on all my tractors and mowers. I just bolt them to the fender or even the top of the deck. They’re waterproof and come in various sizes. They’re cheap, too. You can buy them at Army surplus stores, or just go online and search up military surplus. You can find them as cheap as $6 or $7.”

From the archive · Full text
Reader shop tip

Steve Minarick

Steve Minarick, Morse Bluff, Neb.

“Putting three overhead hoists in our shop has made working on equipment much easier. It also makes it safer and easier to unload pickups and trailers. We use one of them almost every day. No more hurt backs or damaged equipment.”

From the archive · Full text
Reader shop tip

Dan Krenzel

Dan Krenzel, Cullman, Alabama

“Here’s an old farm trick for making welds that take a lot of rod metal. Once you cut the broken sides to an angle, place a welding rod into the groove. Tack the end of the rod to the repair piece. When you start welding, set another rod into the groove, insulating it from the other rod and metal with tape or a couple pieces of rubber. For the weld, use a piece of heavy wire, starting the arc against either the tacked rod or the other one on top. The rod at the bottom will provide all the in-ert gas you need for the arc to stay strong.

“Flexed rods are expensive and this method lets you make use of all your short rods. Plus the arc can be maintained by any heavy wire.”

From the archive · Full text
Reader shop tip

Larry Hudson

Larry Hudson, Calhoun, Ky.

“I have a 4020 Deere tractor and it has a clear open platform which is nice. The problem I have had is that when you have to remove the platform to get to the battery cables and other components, the platform has four bolts - one in each corner. Each bolt has a spacer to hold the platform up off the cables and oil lines. When you remove the bolts, the spacers fall over and the holes fill up with dirt. To solve this problem, I use four pieces of all-thread rod. For each bolt I remove, I insert an all-thread bolt and finger tighten it. I then re-move the platform and it is ready to go back without anything being out of place.”

From the archive · Full text
Reader shop tip

Art Olive

Art Olive, Stacy, Minn.

Here’s a quick, cheap, toolless fix for replacing broken pto shear bolts in the field: All you need is a handful of bolts or steel rod the same diameter as your pto bolts, some duct tape, and an empty toilet paper roll. First, measure the outer diameter of your pto outer shaft and cut off pieces of bolts or rod to fit. You don’t need the heads or threads.

Next, wrap a few feet of duct tape around the toilet paper roll so it stacks neatly. Put the roll with the duct tape and the pieces of bolt in a plastic bag and throw it in your tractor tool box.

When a shear bolt breaks, use a bolt to push out the broken pieces and then push in a replacement bolt pin and wrap it in place with duct tape. Since the shaft is only turning a few hundred rpm, there isn’t much force to throw the bolts out so the duct tape will easily hold. Once you get back to the farm, you can take your time to properly install a new shear bolt.

From the archive · Full text
Reader shop tip 1 of 2

Don Vogel

Individual tip 1 of 2 from this reader’s published contribution.
Don Vogel, Weyburn, Sask. ph 306 842- 5745

“I had an ongoing problem with tubeless tires leaking at the bead. I solved the problem by squirting used anti-freeze between the rim and bead. The antifreeze works amazingly well because it never dries out. I just put the anti-freeze in a squirt bottle. I don’t use this idea on leaks in the tire sidewall - just between the rim and bead.

From the archive · Full text
Reader shop tip 2 of 2

Don Vogel

Individual tip 2 of 2 from this reader’s published contribution.
Don Vogel, Weyburn, Sask. ph 306 842- 5745

“My son built his own bead blaster for tubeless tires using an 8-ft. long, 2-in. dia. air hose, a 1/4-turn valve, and a 60-gal. air tank. Works great on large tubeless truck tires. I turn the valve while my son puts the end of the hose in the tire. My son says it’s the first item he’s ever built that works well without any modification.”

From the archive · Full text
Reader shop tip

Southern Global Tractor Parts

Southern Global Tractor Parts, (ph 866 742-5748; www.southern-global.com)

This company specializes in new, used, and rebuilt parts for Japanese-made compact tractors including Yanmar, Mitsubishi/Satoh, Iseki, Zen-Noh/Kubota, and Shibaura Hinomoto. In addition to those tractors, they carry aftermarket parts for some U.S.compact tractors including Ford, Massey Ferguson, Deere, Bolens, White-Fieldboss, Case-IH, and VST.

“We stock a wide selection of engine parts, hydraulic pumps, starters, alternators, water pumps, fan belts, bearings, oil seals, voltage regulators, manifolds, mufflers, clutches, steering shafts, ignition switches, glow plugs, brake shoes, filters and more,” says the company.

“If we don’t stock the part you want, we can usually order it within 7 to 10 business days.”

They also sell used parts. And they rebuild old starters, alternators, water pumps, injector pumps, injectors and clutches.

From the archive · Full text
Reader shop tip

Bob Corbiel

Bob Corbiel, Unibob Tools (ph 403 556- 1177; www.unibobtools.com)

Trying to install a grease zerk that’s countersunk can be tricky, especially if the zerk is difficult to reach. This specially designed “zerk socket” makes the job easy.

The Nipple Gripper holds the grease zerk in place at the correct depth. Inventor Bob Corbiel machined the inside of a 1/4-in. nut so that it perfectly fits the bottom end of any 1/8 npt grease zerk. He milled a socket and welded the nut inside the socket. He also put a magnet inside the zerk so it can’t slip sideways.

“It holds the zerk rigidly outside the socket at just the right depth,” says Corbiel.

“When you try putting a zerk inside a standard socket, there’s no way to extend the zerk outside the socket far enough so the threads will engage and you can screw it into place. It also works great for removing zerks, too.”

Sells for $10 plus S&H.

From the archive · Full text
Reader shop tip

Gordon Fuller

Gordon Fuller, Barriere, B.C. ph 250 672-0167; [email protected]

“The cord advance on my Weed Eater was always a hassle to operate. To solve the problem, I removed the spool and drilled two small holes about 1/2 in. apart, then threaded the cord through them as shown. I’ve made this modification for several friends, using different sizes and lengths of cord. Usually I use a cord that’s 16 to 20 in. long.”

From the archive · Full text
Reader shop tip 1 of 2

Glen Teel

Individual tip 1 of 2 from this reader’s published contribution.
Glen Teel, Hays, Kansas

“To get rid of rust inside a fuel tank, I put a small length of pipe in the fuel valve which sticks up in the tank about a half inch. The rust stays in the bottom of the tank. I need to remove and drain the tank once in a while in order to remove water.

From the archive · Full text
Reader shop tip 2 of 2

Glen Teel

Individual tip 2 of 2 from this reader’s published contribution.
Glen Teel, Hays, Kansas

“We buried an old tank next to our shop and put our high pressure washer down inside it so it won’t freeze, allowing us use the pressure washer during the winter. We also store paint inside the tank.”

From the archive · Full text
Reader shop tip

Mike Toppen

Mike Toppen, Burnips, Mich.

“With all the interest in wind power, lots of people are taking old car alternators and rebuilding the armature for use on a homemade windmill. I’ve found that by using high power permanent magnets, I can improve power production at lower wind speeds. I press apart the armature and pull out the field coil. Then I repack the field with the magnets and rewind the stator with extra wire. I find these two changes let me produce 13 volts at around 200 rpm compared to the same charge at the 250 rpm speed recommended with a traditional rebuilt alternator.”

From the archive · Full text
Reader shop tip

Mike Takeuchi

Mike Takeuchi, Columbus, Montana

“I needed to remove the valves on a small engine but didn’t have a valve spring compressor. To solve the problem, I threaded a couple of cable ties on opposite sides of the spring and cinched them down in order to compress the spring. To release the spring, I simply cut the ties.”

Shop feature stories

From the archive · Full text
Feature story

Lawn Mower Work Station

Featured source: Paul Meeks

The Lawn Pro Lawnmower Work Station almost makes lawn mower maintenance fun, according to Paul Meeks of Great Day, Inc., in Tallulah, La.

Consisting of two arched ramps (8 1/2 by 48 in.) made of aircraft aluminum with positive traction rungs. Once the lawn mower’s front end has been driven on, the ramps’ stop blocks ensure perfect positioning.

“The Work Station elevates the mower 16 in. off the ground, which is an ideal height to comfortably sit while doing maintenance to conventional or zero turn mowers,” Meeks says.

“We also make an optional stool that puts you at the perfect height for repair work.”

With the lawn mower’s deck exposed and accessible, the Work Station’s handy “flip-n-hold blade holder” locks one, two, or three blades in place instantly for cleaning, sharpening or removal and reinstallation.

An added benefit is that it weighs only 26 lbs., folds flat, and “nests” together for compact, easy storage or transport.

The Work Station sells for $206 (plus S&H.) The optional Pro Work Stool is priced at $59 (plus S&H).

Contact: FARM SHOW Followup, Great Day, Inc., Box 472, Tallulah, La. 71282 (ph 866 649-1918; [email protected]; www.greatdayinc.com).

From the archive · Full text
Feature story

Earth-Sheltered Shop

Featured source: Art Hertz

Art Hertz, Fairfax, S. Dak., built an under-ground shop that always stays at 40 degrees no matter how cold it is outside.

“The temperature inside the shop stays at about 75 degrees during the summer and never goes below 38 degrees during the winter, even when it’s 30 degrees below zero outside,” says Hertz.

The shop is built into the side of a hill and measures 48 ft. long by 32 ft. wide, with 14-ft. high sidewalls. There’s a 24-ft. wide, 16-ft. high bifold door on one side. The walls are poured concrete.

The back side of the building, as well as the roof, are covered with 4 in. of insulation that has a plastic tarp over it, with a 2-ft. deep shell on top of that.

“I built it in 1990 and it has worked great,” says Hertz.

“The only time I use any heat is when I bring in a cold piece of machinery that’s covered in snow and ice. In that case I bring a space heater inside the shop. There’s a bathroom inside and the plumbing has never frozen. There’s also a 12-ft. long by 5-ft. wide deep pit in the middle of the building for servicing trucks and tractors.”

Contact: FARM SHOW Followup, Art Hertz, 36717 Quarry Road, Fairfax, S. Dak. 57335 (ph 605 654-2250).

From the archive · Full text
Feature story

“6-Stroke Engines” Use Waste Heat

Featured source: Bruce Crower / Roger Bajulaz

Countless inventors all over the world are trying to use water to make hydrogen they can run in their 2 and 4-stroke engines. Bruce Crower took a different tack. He decided to make an engine that uses petroleum fuel in its first four strokes and water in strokes five and six. Essentiallly, what he does is capture and use engine heat.

Crower injects water into the cylinder after the exhaust from the gas ignition strokes is exhausted in the fourth stroke. As the water turns instantly to steam, expanding by a factor of 1600, the pressure carries the cylinder through a fifth stroke with the steam being expelled in the sixth stroke.

The effect is to both capture cylinder wall heat for use as power and also to cool the cylinder down. Crower found he could eliminate the normal engine cooling system on the prototype single cylinder diesel he has experimented with.

Crower described the benefits of this to Pete Lyons in a December 2006 article in AutoWeek, “Can you imagine how much fuel goes into radiator losses every day in America? A good spark-ignition engine is about 24 percent efficient, i.e. about 24 cents of your gasoline dollar ends up in power. The Roger Bajulaz from Switzerland took a different tack to the challenge nearly 20 years ago and continues to refine it today. His company, Bajulaz S. A., patented a 6-stroke engine that uses heated air in a cylinder head modified with a combustion chamber inside an air chamber. Heated air from the cylinder charges a combustion chamber as fuel is injected. After ignition, the high pressure is released into the cylinder for an expansion stroke. The heat released at ignition heats the air in the surrounding air chamber, pressurizing it for release to power an additional stroke.

Bajulaz claims thermal efficiency of 50 percent versus 30 percent for traditional internal combustion engines, 40 percent re-duced fuel use, direct injection and optimal fuel combustion at every engine speed. Plus, the company claims almost any type of petroleum or vegetable oil, even animal grease, can be used in the system. This could reduce emissions by 60 to 90 percent.

rest goes out in heat loss through the exhaust or radiator and driving the water pump and the fan and other friction losses.”

Crowder, an experienced inventor and engineer, was sidelined by health issues re-cently. His brother David Crower recently told FARM SHOW that Bruce’s project is on hold until his return.

Contact: FARM SHOW Followup, Bruce Crower, Crower Cams & Equipment Co., Inc., 6180 Business Center Court, San Diego, Calif. 92154 (ph 619 661-6477; fax 619 661-6466; www.crower.com).

Aside from the head, Bajulaz claims no significant modification would be needed to a standard engine design. Like Crower’s engine, the cooling system is reduced. Bajulaz S. A. projects that were a company to adopt the design, cars with it could be on the market within three to five years.

Contact: FARM SHOW Followup, Bajulaz S. A, Matutina Parc, 22 Ave. du Bouchet, 1209, Geneva, Switzerland ([email protected]; www.bajulazsa.com).

From the archive · Full text
Feature story

Gas-Powered Air Compressor

Featured source: Donald Bates

When his portable generator went bad, Donald Bates, Toccoa, Ga., took the rig’s 8 hp Briggs & Stratton electric start gas engine and battery and mounted them on an electric-operated, stationary air compressor, turning it into a portable, gas-powered model. The engine belt-drives the compressor just like the electric motor did.

“I use the compressor to operate air tools such as a grinder equipped with a sanding disc, a nail gun, and a spray paint gun. I can take it with me anywhere I want, and I think it’s a lot cheaper to run the compressor on gas than on electricity. I spent less than $100 to convert it. A new 6 hp gas-powered compressor sells for $700 or more,” says Bates.

He bought the electric-operated, stationary air compressor for $10 at a junk yard. It came with a 20-gal. tank and a belt-driven compressor. He threw away the electric motor, which no longer worked, and unbolted the compressor and moved it back to make room. He added a metal handle and stand at one end of the tank, and a pair of wheels from a riding mower at the other end. A pipe serves as the axle. He made an angle iron frame to mount the engine and battery. He also added an air pressure regulator and the air cleaner off an old garden digger. A solenoid switch makes it easy to start the engine.

Contact: FARM SHOW Followup, Donald Bates, 6611 Simmons Rd., Toccoa, Ga. 30577 (ph 706 716-0789).

From the archive · Full text
Feature story

Hood Repair Tool For Deere Tractors

Featured source: Sunsdahls’ Restoration Tooling

If you’ve got a Deere 3010-3020 or 4000-4020 tractor with a damaged hood, you’ll like this new hood repair tool that helps you accurately re-form the hood nose back to its original factory shape.

The tool consists of an L-shaped steel die that’s machined to the original shape of the factory hood. It’s made from 1-in. thick steel and measures 4 in. long by 3 in. wide and 1 in. deep. A body hammer is used to re-form the hood nose into the die. Once you complete a section you move the die and repeat the process.

“It returns your tractor hood nose to exactly the right radius and angle,” says inventor Dick Sunsdahl, Faribault, Minn.

“You can pound any place on the inside of the hood as long as the hammer hits the die. The tool actually has two functions. It’s a die to form the hood sheet metal into place, and also serves as a gauge that lets you know when you’ve got the hood nose back to its original factory geometry.

“It works fast. It takes only about a half hour to completely re-form a hood back to its original condition.”

Sunsdahl and his tool and die-maker son, Thad, say they looked at a lot of Deere tractors and collected a lot of data before making the die.

“It’s a fairly expensive tool because of the technology we had to use, which included use of a CNC machining center. We spent a lot of time taking dimensions from as many tractors as we could find in our area, and entered the data into a CAD/CAM. The CAD/CAM made slight corrections on our radii and angle measurements which produced the correct dimensions for the prototype. We have a lot of confidence in the tool we came up with.”

They did most of their research on the 3010 and 4010 series because they’re so popular, but say the tool can also be used on Deere models all the way up to the 7020’s. It can even be used on some early 30 series models like the 6030.

Sells for $115 plus $10 S&H. Contact: FARM SHOW Followup, Sunsdahls’ Restoration Tooling, 1703 Green-wood Place, Faribault, Minn. (ph 507 334-8966; [email protected]; www.sunsdahltooling.com).

From the archive · Full text
Feature story

They Specialize In Cat Parts

Featured source: Great Lakes Equipment Company

Looking for used or reconditioned parts for Caterpillar equipment? A great place to start your search may be Great Lakes Equipment Company. Since 1933 the company has been serving the heavy equipment industry. With over 26,000 parts in stock, they’re likely to have the Cat part you need.

The company purchases used Cat tractors and dismantles them. Each part is inspected and cleaned. If the part is in ‘high quality’ condition, it’s immediately added to inventory. Others are rebuilt and tested before being added to the company’s parts list. Parts deemed not worth rebuilding are discarded or offered for sale with full disclosure.

Available parts include everything from engines and transmissions to rollers idlers, final drives, sprocket hubs, frames, wheel assemblies and hitches. Services offered include an undercarriage shop for installation. Attachments are also available.

The company takes special pride in its ability to locate hard-to-find parts. They also offer used parts for Deere, Komatsu, Case, Hitachi and other heavy equipment suppliers.

If you have used heavy construction equipment to sell, give them a call.

Contact: FARM SHOW Followup, Great Lakes Equipment Co., 592 Mayer St., Oglesby, Ill. 61348 (ph 815 883-3610 or 800 634-0084; fax 815 883-8082; [email protected]; www.greatlakesequipment.com).

From the archive · Full text
Feature story

Enclosed Steel Rack Keeps Inventory Handy

Featured source: Roger Gutschmidt

This sharp and tidy-looking “steel shack” is one of Roger Gutschmidt’s most useful shop innovations.

“I absolutely love this rack and can’t imagine being without it,” he says.

“Since I’m always working on projects, I’m in it every day. It sets right outside my shop and holds my inventory of steel tubing, angle iron, shafts, flat iron, and 4 by 8 metal sheets.”

The storage unit measures about 42 in. wide by 48 in. high, and is 12 ft., 4 in. long. The compartments each measure 5 by 7 in. and are set up in a “checkerboard” pattern.

“I used a checkerboard design because it cut the amount of tubing needed in half,” he says.

“I have a large upright compartment on the right to hold 4 by 8-ft. sheets of steel. It has a hinged door at each end and I painted it with acrylic enamel automotive paint to match my shop’s exterior siding.”

(Gutschmidt points out that automotive paint is much more weather and fade resistant than enamel paints like you find at most building supply stores.) “Storing steel inside the shop is nice, but it takes up a lot of room, and tends to make things look cluttered and messy,” he says.

“This design keeps my steel organized and it’s easy to see at a glance what I have.”

Gutschmidt built the steel shack in 2002.

The 25 pieces of 5 by 7-in. steel tubing cost him $702. The sheet metal for the shell and doors was $250, and the paint cost $491.

“This project cost me a grand total of around $1,500, and that’s without my labor, but it has certainly been well worth my investment because it’s so handy,” he says.

Contact: FARM SHOW Followup, Gutschmidt Manufacturing, LLC, Roger Gutschmidt, 6651 Hwy. 56, Gackle, N. Dak. 58442 (ph 701 698-2310; [email protected]).

From the archive · Full text
Feature story

Stick-On Roofing Has Lots Of Uses

Featured source: MFM Building Products Corp.

“It has been used to re-cover mobile home and RV roofs for about 20 years, but people keep coming up with new uses for it,” says Tod Windsor, MFM Building Products Corp., about Peel & Seal roofing. It’s an aluminum-backed, rubberized asphalt product that you simply roll out and stick in place.

“It can be used to patch leaking metal roofs or to seal seams between roofing panels. It has even been used by truckers to patch trailer walls quickly.”

Other uses for the product include gutter and flashing repair, as well as sealing seams between aluminum panels on sunroofs. Windsor says it’s also used in construction to provide a waterproof seal before putting shingles or other roofing materials over the top.

The aluminum exterior layer reflects sunlight, giving the product its cooling properties. Windsor says Peel & Seal will cool a building by 20 degrees compared to a traditionally shingled roof. This reflectivity has earned it the Energy Star rating, which can qualify for rebates with some electricity suppliers as well as tax credits.

Peel & Seal is available in four colors and in widths of 3, 4, 6, 9, 12, 18, and 36 in.

“I know people who use it to patch their cars, and it’s great for sealing over nails in metal roofing,” says Windsor.

“You can cover just the nails or do the entire roof. It’s amazingly useful, like a serious piece of duct tape.”

Contact: FARM SHOW Followup, MFM Building Products Corp., 525 Orange St., P.O. Box 340, Coshocton, Ohio 43812 (ph 800 882-7663; fax 740 622-6161; [email protected]; www.mfmbp.com).

From the archive · Full text
Feature story

How To Fix Leaking Deere FWA Hydraulic Motors

Featured source: Roger Gutschmidt

“A lot of the front wheel assist (FWA) hydraulic motors on older 20, 30 and 40 series Deere tractors are leaking now, and many people don’t know where to go to get them repaired,” says Roger Gutschmidt of Gackle, N. Dak.

“I was in the same boat, but stumbled onto a company that specializes in rebuilding them. This place does phenomenal work.”

Gutschmidt restores his own tractors, and the first time he dealt with leaking hydraulic motors, he learned the hard way what not to do. He first took them to his local Deere dealership, where they replaced some seals... but when he got them back, the motors still leaked.

“Usually what’s wrong is that they leak oil out of the relief valve, but you can’t just go and replace the valve because it doesn’t solve the problem. I found this place - Hydro Service in Roland, Iowa - where their specialty is machining these motors and checking the tolerances of the rotating assembly, which totally eliminates the problem.”

“Sundstrand manufactured these motors. Sundstrand also makes many of the hydrostatic units on rear wheel assist combines,” he explains.

“If the motors are engaged for long periods, they almost all leak.”

Before Gutschmidt sent his two motors to Hydro Service, they advised him to insure them.

“These motors are quite valuable because they don’t make them any more,” he points out.

When he phoned the company less than a week later to check on the job, he was told the motors were already on the way back to him. The charge at the time was $240 per motor.

He was so happy with the results that he wrote the company the following letter: “I installed the FWA motors that you re-conditioned in my tractor today. Everything looked real good. I then took the tractor to the field and tested the FWA. I had a leveler hooked to the tractor. I drove till the leveler was completely full of dirt and the tractor just sat there and spun, then I put the FWA in gear and it just ‘walked’ out of there. They worked perfect. I’m so happy I found out about you guys. Your service is excellent. You will be highly recommended by me to fellow FWA owners. I wrote the check out with a smile on my face. Thanks again for the good work and fast service.”

Contact: FARM SHOW Followup, Gutschmidt Manufacturing, LLC, Roger Gutschmidt, 6651 Hwy. 56, Gackle, N. Dak. 58442 (ph 701 698-2310; [email protected]) or Hydro Service, 202 N. Main Street, Roland, Iowa 50236 (ph 515 388-4096).

From the archive · Full text
Feature story

Push Button Grease Pit Cover Up

Featured source: Bill Dorwin

Grease pits are handy, but dangerous if left open. Pulling heavy covers off a pit long enough to work both ends of a truck is a pain. When Bill Dorwin’s son Jeff built a new shop for servicing their over-the-road tractors, he asked his dad for ideas for a push button cover.

“When he came off the road in the middle of the night with a tractor that needed servicing, he wanted to hit a button to uncover the pit, open the petcock and let the hot oil drain while he went to bed,” says Dorwin.

“I just had to figure out how it would work.”

What he settled on was a kind of giant garage door opener that moves 10 4-ft. cover sections of 1/4-in. thick deck plate back and forth across the top of the grease pit. For starters, the oil pit was made twice as long as needed at 5 ft. deep, 4 ft. wide, and 40 ft. long. There’s also a 3-ft. deep, 43-ft. extension where the deck plate covers retract.

A gearbox installed where the two pits meet drives no. 80 roller chain through a 2-in. channel iron box filled with oil. Midway down the length of the channel, the chain connects at the midpoint of the working pit covers.

“I figured if we connected at the front or back, the plates would buckle when pushed,” says Dorwin.

“This way only half the plates are pushed, while the other half are pulled, whether opening or closing.”

To move the plates smoothly under the storage cover, Dorwin mounted rollers under the first and last plates. This allows them to smoothly roll up and down the 4-in. incline to cover or uncover the working pit. Sweeps also mounted at both end plates sweep the track, keeping debris off and ensuring a smooth action.

The plates themselves rest on track along the side of the pit. A second set of tracks runs slightly beneath the cover track. It supports a 30-gal. drain tank on rollers. It can be moved from one end of the working pit to the other, enabling draining of engine, rear end or transmission fluids as needed and without moving the vehicle being serviced.

“The oil pan has wings on the top that can be flipped up to help catch fluids coming from either side of the pan,” notes Dorwin.

“At the end of the pit, we have a pump under the entrance steps. When the oil pan is full, we simply wheel it down to the pump and empty it into a waste oil storage tank. In the winter, we burn the waste oil to heat the shop.”

The service pit covers are reinforced with gussets to allow light trucks or skid steer-sized equipment to be driven over them.

“It only takes 45 seconds to uncover the working pit with the opener,” says Dorwin.

“Thanks to the pit, we can drop the oil, grease and service a truck in about 20 minutes.”

Contact: FARM SHOW Followup, Bill Dorwin, W.L. Dorwin Backhoe Service, W4794 Cty. Rd. B, Durand, Wis. 54736 (ph 715 671-5679; [email protected]).

From the archive · Full text
Feature story

Self-Contained Hydraulic Cylinders

Featured source: Vicki Stephens

Electrohydraulic Actuators (EHA’s) are slick substitutes for hydraulic cylinders for many applications. Because they run off the electrical system, they help avoid overloading existing hydraulics. The EHA contains pump, reservoir double acting cylinder, relief and check valves...everything needed in a self-contained unit.

Common applications are as lifts for mower decks, attachments for ATV’s, and latches and lifts on farm and industrial machinery. Linear actuators can do much the same job as hydraulic cylinders, but tend to be slower and not as powerful. The only problem is finding the EHA you want.

“EHA’s are custom designed for the application. We work with OEMs,” says Vicki Stephens, Oildyne Division, Parker Hannifin.

“Our new compact EHA is built to order with minimum orders of 500. It’s unlikely a distributor would be willing to stock some if he didn’t carry the equipment for which it was designed.”

Are they worth finding? A look at Oildyne’s new Parker Compact EHA shows why one might want to look. It’s available in three bore sizes, with strokes of up to 8-in. and speeds of 5.1 in./sec. The unit can produce a force of up to 5,000 lbs. Compare that with a linear actuator available online at Northern Equipment. It offered an 11 13/16-in. stroke, 1,350-lb. force and a travel speed of about 1/3-in./sec.

While Stephens says confidentiality agree-ments with customers prevent her from saying who’s using a Parker EHA, they’re available in parts departments. If you think one would be useful, the best bet is to go to a major equipment supplier. FARM SHOW checked with local Deere and New Holland parts departments. Both had EHA’s on their books and available.

Once desired length of stroke, lift and available space have been identified, visit the parts department and ask what’s available. Of course, if you’re looking for 500 or more, talk to Stephens.

Contact: FARM SHOW Followup, Vicki Stephens, Hydraulics Group, Oildyne Division, 5520 North Highway 169, New Hope, Minn. 55428 (ph 763 533-3528; fax 763 533-0082; [email protected]; www.parker.com).