From the archive · Full text
Feature story
Featured source: SureCan, North Ogden, Utah
With a rotating spout that pours from the bottom, SureCan offers a new design in fuel cans that makes it easier to use for filling tanks on everything from a lawnmower to a tractor.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: LockNLube, West Lebanon, N.H.
The LockNFlate Air Chuck locks onto tire valves leaving your hands free while pressurizing a tire. Recently introduced by LockNLube, maker of the lock on grease coupler (Vol. 38, No. 3), the air chuck uses a similar locking…
Read the complete story →From the archive · Full text
Feature story
Featured source: Carl Stoloski
When Carl Stoloski needed to replace some outbuilding doors, he initially planned on using an old school track and pulley system for rolling the new doors open and closed.
Read the complete story →From the archive · Full text
Feature story
Featured source: Scott Ravenkamp, Verdigre, Neb.
Scott Ravenkamp needed a welding table in his shop. He had previously used the main frame of a 40-ft. rod weeder to add a loft to his shop, so he had the rest of the components from the…
Read the complete story →From the archive · Full text
Reader shop tip
Chris Perkins, Southern Ind.
“When you build equipment and have to look at little blurry schematics online, a mounted big screen TV works great in the shop.”
Read the complete tip →From the archive · Full text
Reader shop tip
Ken Todd, Red Deer County, Alberta
“On page 89 of your Great Shop Ideas – Vol IV book, Tom Cogger talks about having trouble with crimped wire connectors not holding and advises using heat shrink to hold them in place.
Read the complete tip →From the archive · Full text
Reader shop tip
Tim Reisenauer, Kennewick, Wash.
“I’ve found that if I throw the rusty tools in my shop stove for a day and then pull them out before lighting the fire again, my glass bead blaster will do a better job cleaning them up.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Tony Bunniss, Webster, Minn.
Tony Bunniss repurposed a BBQ grill into a movable shop table/storage unit.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Dale Fisher, Jackson, Mich.
“I store chains in my shop by hanging the hooks from the edge of a 55-gal. drum. Works much better than just putting them in a pile. When I need a chain, I just grab one and go.”
Read the complete tip →From the archive · Full text
Reader shop tip
David Simpler, Elkton, Md.
“Lots of shops have old refrigerators in them to hold welding rods. But if you’re short on space and don’t have a lot of welding rods, use an old microwave with a light on inside to keep them…
Read the complete tip →From the archive · Full text
Reader shop tip
Jim Rankin, Paris, Ky.
“I weld a 1/2-in. box-end wrench on one handle of a set of pliers and a 9/16-in. wrench on the other handle. It makes my pliers about the handiest tool I own. I’ve used this idea for many…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Wayne and Charlene Eash, Ligonier, Ind.
Wayne and Charlene Eash got the idea for a self-propelled ladder when a friend showed them one he had made.
Read the complete story →From the archive · Full text
Reader shop tip
Fritz Groszkruger, Dumont, Iowa
“I had a broken bolt that holds the fuel filter bracket on my 3010 diesel. My mechanic said I should convert to the modern square filter anyway. The bolt was about 1/4-in. deep into the block. After trying…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Gerald Mullen, Mantua, N.J.
“The Jerry Clip is designed to eliminate the frustration of not having a writing instrument, which we’re all familiar with,” says Jerry Clip inventor Gerald Mullen.
Read the complete story →From the archive · Full text
Reader shop tip
Steve Coley, Meeker, Colo.
“Here’s a trick for finding all of the pinholes in a rusty fuel tank. First, get the tank ‘boiled out’ at a radiator shop. Then get a magic marker and a flashlight or light bulb that will fit…
Read the complete tip →From the archive · Full text
Reader shop tip
Gary Lee Meeks, Augusta County, Va.
“When old-style shed door rollers jump off the track, I have found that the see-saw tool used to lift the bottom edge of wallboard works well. Just slip it under the door, pry it up with your foot,…
Read the complete tip →From the archive · Full text
Reader shop tip
Karl Spees, Port Angeles, Wash.
“I came up with an idea while working on an unusual project. It might help out on many projects in the shop.
Read the complete tip →From the archive · Full text
Feature story
Featured source: Tech-Bond Solutions, Newark, Ohio
Tech-Bond Solutions sells a polymer patch that works on pvc, galvanized, and copper pipes, and any kind of water tank except for stainless. Designed to quickly seal up cracks or holes, the patent-pending patch is made with flourosilicone…
Read the complete story →From the archive · Full text
Feature story
Featured source: Nick Gebhardt, Black River Falls, Wis.
For one cranberry farmer, a passion for helping others has turned into a profitable business. Nick Gebhardt is a fourth-generation farmer who works with his brother to manage close to 300 acres of cranberries grown for Ocean Spray.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Bosch Automotive Service Solutions, Warren, Mich.
Two-speed hydraulic hand pumps from Bosch offer a versatile alternative to power hydraulics or bottle jacks for many shop uses. The OTC 4004 hydraulic hand pump can produce 10,000 psi, compatible with rams between 10 and 100 tons.
Read the complete story →From the archive · Full text
Feature story
Featured source: Roger Podoll, Wautoma, Wis.
Roger Podoll has found multiple uses for old radiator cores. He sticks them in front of the OEM radiator core on skid steers and tractors as a pre-cleaner and also uses them as filters in his shop.
Read the complete story →From the archive · Full text
Feature story
Featured source: Tony Bunniss, Webster, Minn.
Tony Bunniss built an extension on his tuck-under garage to expand it to a 4-car garage, which Bunniss heated and air-conditioned. The original garage section then became a machine shop.
Read the complete story →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Gerald Wright, Pendleton, Ky.
“While shopping at a tool outlet store, I found a Dewalt adapter that lets you fit the new 20-volt lithium ion batteries into the old 18-volt tools. It gave my old tools new life. You can pick up…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Timothy Rankin, Middlebrook, Va.
“After a friend of mine lit a trash barrel on fire in his shop while cutting metal, I realized that could easily happen to me, too. So I made a lid for my barrel out of flat sheet…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Cory Pleschourt, Northfield, Minn.
“I hate ‘pushed in’ grease zerks. More often than not they will eventually pull out with the grease gun end when done greasing. To solve the issue permanently, I thread the zerk mounting hole and install threaded grease…
Read the complete tip →From the archive · Full text
Reader shop tip
Leroy Oberholtzer, Greenwich, Ohio
“I have found that when using my shop press to remove or install bushings and bearings, that impact sockets make great punches for pushing them in or out.”
Read the complete tip →From the archive · Full text
Feature story
Featured source: Randy Emerick
PermaFlex fromSANI-TRED is a liquid rubber-like adhesive coating that can seal up just about any surface. Randy Emerick at SANI-TRED says its most important qualities are its penetration and its flexible elongation memory. That means it penetrates deep…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Bruce Pigeon
Handling big farm wheels and tires up to 90-in. dia. is safe and easy with the Tire Wrangler built by a North Dakota company. Owner Bruce Pigeon says the Tire Wrangler works in conjunction with his patented Agri-Jack…
Read the complete story →From the archive · Full text
Reader shop tip
Bern Smith, Madison, Fla.
“I mounted an old pan-type tractor seat from an Allis WD onto the base of a discarded office chair. It rolls easily around the shop and is as comfortable as riding the Allis. It really works great.”
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Gabriel Gaitan, Sandia, Texas
“I keep a sand bucket on my shop table that’s saturated with a 50:50 mix of both mineral and olive oil. Shoving small tools into the sand keeps them rust-free.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Aldon Cisco, Ohio
“Here’s an idea for a handy shop light you can make out of a regular small LED flashlight. Just zip tie a clothes pin to the light by running the zip tie through the spring on the clothes…
Read the complete tip →From the archive · Full text
Reader shop tip
David Matthews, Chapin, S.C.
David made a shop fan by salvaging the fan off the top of an old household AC unit. He wired the fan motor to a switch box he attached to the side of the unit and attached a…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Ethan Schwoeppe, Huntingburg, Ind.
“Old disk blades make great pedestal mount bases for shop tools. For example, I made a bench grinder stand by welding a 3-ft. long pipe onto a 20-in. broken disk blade, then welding a scrap steel bracket on…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Karl Scheibengraber, Lisbon, Wis.
“Whenever I would lay down a piece of cardboard and lay down on my side to service or repair vehicles, I would get a sore neck if I didn’t support my head somehow. Old pillows or a folded…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Lauren Rasmussen, Kokomo, Ind.
“Small pieces of a plastic shopping bag can be used as a thread locker on bolts or as a sealant on pipe threads.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Lauren Rasmussen, Kokomo, Ind.
“I use a light chain hanging from the ceiling of my shop to help support long items on the drill press.”
Read the complete tip →From the archive · Full text
Feature story
Featured source: Michael Veatch
Michael Veatch, Republic, Mo., modified a jack-operated shop engine hoist so that it can be quickly attached to the receiver hitch on his pickup.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Horizon Products
The newest tool to clean out dried grease behind zerks is the Zerk Zapper from Horizon Products, Hot Springs Village, Ark.
Read the complete story →From the archive · Full text
Feature story
Featured source: Bill Shipman
Bill Shipman, Elwood, Ind., found several uses for old golf equipment around his shop.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Tom Dufrense, Grant, Minn.
“I got tired of having coiled air hose getting tangled up around my portable shop air compressor. So I bolted a heavy-duty air hose reel on top of the compressor’s pull handle. It was relatively easy to attach…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
John Matthews, Chapin, S.C.
“A short length of pvc pipe serves as a holder that keeps my mini grease gun handy right outside my storage shed. I cut a slot in one end of the pipe to accommodate the handle and then…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Tom Chaney, Chrisman, Ill.
“I didn’t like wall-mounted oil funnels dripping oil down my shop wall and making a mess, so I shoved the neck of an empty plastic soda bottle up onto the bottom end of a transmission oil funnel. I…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 4
Individual tip 2 of 4 from this reader’s published contribution.
Preston Williams, Victoria, Va.
“I put two 8-ft. long LED light strips on each side of my 30 by 30-ft. shop and was amazed at how well it lit up the entire shop. Makes it much easier to work when you’ve got…
Read the complete tip →From the archive · Full text
Reader shop tip
Steward Vander Vere, Allegan, Mich.
“I paid $20 for a 3-piece caster set designed for storing a snowmobile in tight quarters. The casters work great on my snowplow so I can roll it out of the way in my shop.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Doug Johnson
“Keeping track of hitch pins and lynch pins on our property, with 3 tractors and a Deere Gator, used to be almost impossible. Even when left in wagon hitches or on a 3-pt. hitch, the pins always seemed…
Read the complete story →From the archive · Full text
Feature story
Featured source: Dean Aasheim
Dean Aasheim, Canton, S. Dak., converted a rolling engine hoist into a handy scaffold that makes it easier to work on 14-ft. ceilings inside a building he added onto his mobile home.
Read the complete story →From the archive · Full text
Reader shop tip 3 of 4
Individual tip 3 of 4 from this reader’s published contribution.
Milan Hochstetler, Cumberland, Va.
“The rope that opens my overhead garage door was small and hard to grip, so to improve the grip I attached golf balls to the rope at 1-ft. intervals. I drilled a hole through each ball, then ran…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Ready Davis, McKinleyville, Calif.
“I run a repair shop and one idea that has really helped me a lot in recent years is using my pneumatic hammer on frozen bearings and rusted shafts. Helps get jobs done faster.
Read the complete tip →From the archive · Full text
Reader shop tip
Mark Yax, Solon, Ohio
“I’ve found that if you cut off the tops of detergent bottles and use them upside down, they make great little almost spill-proof containers for holding cutting oils, glues, stains, and paint. Handy to keep around the shop.”
Read the complete tip →From the archive · Full text
Feature story
Featured source: Brian Laine
Tired of leaving your shop to go out in the cold, rain or snow to relieve yourself? Shop Relief may be your answer, says Brian Laine, Arlington, Wash. ShopRelief is a waterless fold-out urinal for your shop. Installed…
Read the complete story →From the archive · Full text
Reader shop tip
Elwin Gingerich, Kalona, Iowa
“If you have a housing that needs a seal but the seal fits loosely because the housing is worn, get a 12-volt battery and a set of jumper cables. Attach the negative cable to the housing and the…
Read the complete tip →From the archive · Full text
Reader shop tip
James Minix, Morrison, Tenn.
“I was having trouble keeping plastic electric fence insulators from breaking prematurely on chain link fence due to sunlight causing them to get brittle and weak. So I got the idea to protect them by coating the end…
Read the complete tip →From the archive · Full text
Reader shop tip
Eric Dyck, Sevenpersons, Alberta
“I keep a shopping cart in my shop with my most commonly used tools. Makes them easy to find and I can quickly take them to where I’m working.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
John Daugherty, Gray, Ga.
“Here’s how I made some insulating buckets to put over our outdoor faucets in the winter to keep them from freezing. I bent some wire into a cylinder, taped some newspaper around it, and put it in the…
Read the complete tip →From the archive · Full text
Reader shop tip
Lee Shepherd, Wabash, Ind.
Lee runs a small engine repair shop for lawn and garden tractors. He recently made a custom exhaust “tip” out of an old fire extinguisher that he had laying around. It sticks off the front of one of…
Read the complete tip →From the archive · Full text
Reader shop tip
Thomas G. Herriman, Bainbridge, Ga.
“I put two 7/16-in. eye bolts over my garage door opening and put a chain through them to lift my Deere 125 mower for blade work. Works great and is safe. Don’t forget to put the gas cap…
Read the complete tip →From the archive · Full text
Reader shop tip
Travis Jensen, Dell Rapids, S.Dak.
“I run well water through an old tractor radiator and have a fan blowing through it from behind. Makes a cheap air conditioner for my shop.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Don Boggs
“Here’s a simple chain holder that will make it easy to find the right-sized chain when you need it,” says Don Boggs of Pickens, S.C.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Jeff Prose
“Anyone who’s ever braised, welded or soldered likely has a permanent ‘metalworking brand’ because of flying sparks and slag,” says pipefitter Jeff Prose.
Read the complete story →