From the archive · Full text
Feature story
Featured source:
You’ll never have to worry about draining power out of your batteries when machinery’s not in use, thanks to this new remote battery disconnect safety switch. The device, from Gizmos & Gadgets Inc., consists of a knife blade-type…
Read the complete story →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
James B. Barbour, Hallstead, Penn.
“Another idea I had was making a cradle to fit my hydraulic floor jack to make it easier to change starters on cars or trucks. It’s just a short piece of channel iron with a bolt down the…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Roland Schild, Greenfield, Ill., got the idea for this pipe bender after seeing one in a machine shop.
Read the complete story →From the archive · Full text
Reader shop tip
George Martin, Merrimac, Wis.
“You can make a handy squeeze-type oiler out of an empty yellow Heet bottle, or other similar container, and a piece of small diameter air tube of the type used on air shocks. Cut off a piece of…
Read the complete tip →From the archive · Full text
Reader shop tip
Jim Murray, Lakeview, N.C.
“Here’s a tip that may save other farmers some money if they own diesel engines with glow plugs. My 1985 Ford F-250 4-WD with 170,000 miles on it and had the original glow plugs in its 6.9 IH…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Roger & Bruce Elliott, Montrose, Ill.
The Elliotts built a hydraulic hose center where they make their own hose. They built a 7 1/2-ft. tall by 2-ft. wide stand out of 2-in. box tubing. It’s fitted with four wood reels holding four different types…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Roger & Bruce Elliott, Montrose, Ill.
Another improvement the Elliotts made is a pair of extension cords suspended from the ceiling. One is a 110-volt cable fitted with a standard 3-prong plug and the other is a 220-volt cable fitted with a 50-amp plug…
Read the complete tip →From the archive · Full text
Reader shop tip
Francis Roberts, Seligman, Mo.
“My simple corrugated metal cutter is a great way to cut through corrugated sheet metal roofing or siding, whether you’re cutting straight across or at an angle,” says Roberts, who made his metal cutter out of scrap materials.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Jim Kaufman, Moundridge, Kan.
“An inexpensive method of building a high volume air compressor is to use a small compressor and a large volume tank. I use a 300-gal. tank off an old NH3 applicator. These tanks are cheap, fairly readily available,…
Read the complete tip →From the archive · Full text
Reader shop tip
Roland Schild, Greenview, Ill.
You’ll get a better grease job with an air-powered grease gun, according to Schild, who bought his gun at a NAPA auto parts store. He mounts the grease gun, which fits on top of a 5-gal. bucket of…
Read the complete tip →From the archive · Full text
Reader shop tip
Bill Reeks, Cromwell, Ky.
“Tin cans are great for carrying a quart bottle of oil under the hood of your car or pickup. Just find a tin can that’s large enough to hold a 1-qt. container and screw, wire or bolt it…
Read the complete tip →From the archive · Full text
Reader shop tip
Leonard Donovan, E E Donovan & Sons, Mallorytown, Ontario
“Our Deere 3130 (2840 model in U.S.) was a hard starter in cold weather. So I bought new higher-cranking batteries than the Deere originals and wired them up differently to solve the problem. I used two new 950…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
The 3-pt. hitch on popular Case-IH Magnum tractors is controlled by a set of load sensing pins. Jay Bottolfson, Vermillion, S. Dak., had problems with the pins so he came up with a modification kit called the “Pin…
Read the complete story →From the archive · Full text
Reader shop tip
Harlan Olson, Elbow Lake, Minn.
“I made this handy swing-out shop light a few years ago.
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source:
A Florida inventor came up with this nifty “sawstand” that’s equipped with a foot-operated clamp, making it easy to cut through pipe, rods, electrical conduit, or even small dimension lumber.
Read the complete story →From the archive · Full text
Reader shop tip
John Voigt, Avon, S.Dak.
“I built a parts washer from an old water softener barrel and a salvaged electric fuel pump. The plastic barrel had a screen platform at the bottom. I cut the top half of the barrel off and mounted…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Wayne Hagen, Lake Alma, Sask.
“The problem with most small tubing benders is that they’re hand-operated and must be upright to work and in tight spaces you can run out of room. They’re also labor intensive. My bender is built to work horizontally…
Read the complete tip →From the archive · Full text
Reader shop tip
Charles Sorensen, Corwith, Iowa
“I used galvanized steel pipe, a disk blade, and an old Teflon frying pan to make a portable, telescoping shop light that also doubles as a bolt or tool tray. The light can be adjusted from 4 to…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 4
Individual tip 2 of 4 from this reader’s published contribution.
John M. Kiminski, North Brookfield, Mass.
“Here’s another idea: Several years ago I bought a $25 automotive electric fuel pump and put a length of gas line hose on both outlets. I’ve used it to drain out many a gas tank that needed repair…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source:
If you’re tired of hassling with tangled-up extension cords, you’ll want to take a look at this “Whipper Reel” cord retriever that fastens to walls or ceilings or can be staked to the ground.
Read the complete story →From the archive · Full text
Reader shop tip
Edwin Ruff, Moses Lake, Wash.
“To push another vehicle, tie an old tire to the front of your vehicle with a bungy cord. Then you can easily push another vehicle with no hard bumps. On corners or rough spots, you can give extra…
Read the complete tip →From the archive · Full text
Reader shop tip
Harvey Mueller, Neosho, Wis.
“The remote control I built for my Lincoln 275 amp hand-cranked stick welder back in 1950 has saved me a tremendous amount of time because I don’t have to run back and forth to my welder to turn…
Read the complete tip →From the archive · Full text
Reader shop tip
James Nedrow, Ashton, Idaho
“Our 1977 White 2-70 diesel tractor has never started easy - we’ve always had to use the electric engine heater every morning year around. In the winter we have to spray ether into the air cleaner in order…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
You can make your own low-cost “roto rooter” out of odds and ends you probably already have on hand, says J.D. Higdon.
Read the complete story →From the archive · Full text
Reader shop tip
Larry McWilliams, Tulsa, Okla.
“I came up with a simple way to store pipe or lumber using old tires. Just suspend a pair of tires from the rafters of a shed or shop using wire, cable or rope. There are many different…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Robert Ingram, McArthur, Calif.
“We have an Allis Chalmers D-14 tractor that was originally equipped with a 6-volt positive ground electrical system which made it difficult to start. We always had to park it on a hill and roll it down to…
Read the complete tip →From the archive · Full text
Reader shop tip
Dave Linstad, Porterfield, Wis.
“I’ve found that I can reduce damage to electric fences from deer running into them at night by fitting a 1-ft. length of spring off an over-head garage door opener on each end of the wire. Lets the…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Garth Luchterhand, Loyal, Wis.
“My electric start snowblower has a rubber push button switch that gets stiff and won’t work when cold. I solved the problem by softening it up with an electric hair dryer.”
Read the complete tip →