Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW

Electrical

928 shop tips and stories · page 11 of 16, newest issues first.

From the archive · Full text
Reader shop tip 1 of 4

Ben Burlingame

Individual tip 1 of 4 from this reader’s published contribution.
Ben Burlingame, Charlton, Mass.

“The battery on my 1972 Sears Custom 10 garden tractor wouldn’t hold a charge. After being quoted sky high prices for a new charging system, I bought a Chevy alternator from a local junk yard. Now that battery…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Allen Ahlbrecht

Individual tip 1 of 2 from this reader’s published contribution.
Allen Ahlbrecht, Hector, Minn.

“We had been having a lot of problems with wheel bearings on equipment, especially the smaller tag axles bolted to our trucks to get past road restrictions each spring. After switching to a synthetic grease, the problem went…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 3

Bill Reeks

Individual tip 1 of 3 from this reader’s published contribution.
Bill Reeks, Cromwell, Ky.

“It’s surprising how much stuff this 7.62 mm ammuni-tion box will hold. I use it to hold a chain, rope, wrench, pliers, screwdrivers, tape, vise grips, crescent wrench, wire, etc. I keep re-serve gas in a 24 oz.…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Eugene P. Yavorski

Individual tip 2 of 2 from this reader’s published contribution.
Eugene P. Yavorski, Palm Coast, Fla.

“I use a Honda 3,400-lb. psi pressure washer around my home to clean my driveway, etc. With that much pressure the wand is always exerting an upward pressure on my arms, which really gets tiring. To counterbal-ance the…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 3

Gary Elston

Individual tip 2 of 3 from this reader’s published contribution.
Gary Elston, Mulvane, Kansas

“Broken or bad wiring due to poor connections is a headache for anyone. I’ve found that dielectric grease is a cheap and easy way to protect electrical plug-ins and couplers from water and to keep dirt from corroding…

Read the complete tip →
From the archive · Full text
Reader shop tip 3 of 3

Gary Elston

Individual tip 3 of 3 from this reader’s published contribution.
Gary Elston, Mulvane, Kansas

“A good way to repair broken wiring is to strip the two wires to be joined, then solder them and use heat shrink tube to seal the fix. A better and simpler fix is to pick up a…

Read the complete tip →
From the archive · Full text
Reader shop tip 3 of 5

Bill Reeks

Individual tip 3 of 5 from this reader’s published contribution.
Bill Reeks, Cromwell, Ky.

“When I need a short piece of small wire I use a paper clip. They’re cheap, readily available, and provide the size you need when other sources aren’t there. A jumbo size clip will provide 6 3/8 in.…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

W.A. Gibbs

Individual tip 1 of 2 from this reader’s published contribution.
W.A. Gibbs, Elmwood, Tenn.

“When I lost the ignition key to my 1958 Chevrolet 2-ton dump truck, I was able to come up with a simple, low-cost solution without ever touching the old ignition switch. It was a lot easier than putting…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

W.A. Gibbs

Individual tip 2 of 2 from this reader’s published contribution.
W.A. Gibbs, Elmwood, Tenn.

“I used the same idea on my 1961 Deere 1010 dozer, except that on the dozer I installed an extra switch. I still use both switches. With the original switch I had trouble burning up ignition points. Now…

Read the complete tip →
From the archive · Full text
Reader shop tip

Rachel Crowe

Rachel Crowe, Skull Valley, Ariz.

The electric motor in her washing machine was worn out so she replaced it with a 3/8-in. drill mounted in a custom bracket. She chucked a pulley into the drill to turn the machine’s V-belt. Forward runs the…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Murray Scea

Individual tip 1 of 2 from this reader’s published contribution.
Murray Scea, Campbellford, Ontario

“I’ve found that ordinary gutter hangers work great on my shop wall for storing stuff. I use them to store extension cords, hoses, garden tools, jumper cables, oil changing pans, etc. They’re even strong enough to hold tires.

Read the complete tip →
From the archive · Full text
Reader shop tip

Wingfield Distributors, Inc.

Wingfield Distributors, Inc., 4712 N. Cunningham Ave., Urbana, Ill. 61801 ph 800 637-6712; fax 217 643-7849; www.wingfields.com

This company offers a new screw-holding driver made in Germany. The design permits single-handed operation for starting a screw, allowing easier access in tight places. It allows you to place screws through holes or in hard-to-reach places without…

Read the complete tip →
From the archive · Full text
Reader shop tip 3 of 3

Jim Matthews

Individual tip 3 of 3 from this reader’s published contribution.
Jim Matthews, Saskatoon, Sask.

“If you have a small shed without any electricity and want to have light inside it, you can use a solar battery charger to power a light. You can buy these solar battery chargers cheap at Wal-Mart and…

Read the complete tip →
From the archive · Full text
Reader shop tip 3 of 3

Gerald A. Borders

Individual tip 3 of 3 from this reader’s published contribution.
Gerald A. Borders, Sullivan, Ind.

“I use a non-contact electronic thermometer to check the temperature of bearings, radiators, engines, electrical connections, etc. Saves a lot of problems and time.”

Read the complete tip →
From the archive · Full text
Reader shop tip 4 of 5

Lonnie J. Wallace

Individual tip 4 of 5 from this reader’s published contribution.
Lonnie J. Wallace, Jerico Springs, Mo.

“I’ve found that General Electric soft white 60-watt light bulbs make the best rough service bulbs. They’re fluorescent so they don’t get hot.

Read the complete tip →