From the archive · Full text
Reader shop tip
Duane Kuesel, Elmwood, Wis.
“I prolong the life of the hydraulic lines on my front-end loader by slipping steel electrical conduit over them. It saves the rubber from being peeled off when pushing brush and tree branches. Plastic conduit could also be…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 4
Individual tip 1 of 4 from this reader’s published contribution.
Milan Hochstetler, Cumberland, Va.
“I made my own paint can shaker by using the electric motor off an old ice cream freezer. I removed the paddle that stirred the ice cream and used JB Weld to attach a wood block to the…
Read the complete tip →From the archive · Full text
Reader shop tip
Trevor Firth, New South Wales, New Brunswick, Canada
“My wife couldn’t start our self-propelled, 21-in. self-propelled mower using the pull cord, so I came up with a way to use a cordless drill to do the job. The pull cord assembly acts on a disc that’s…
Read the complete tip →From the archive · Full text
Reader shop tip
Chuck Staley, Charter Oak, Iowa
“To the reader frustrated with his X750 Deere mower that shuts down when he shifts into reverse, just remove the two wires that run to the button you push when backing up and connect them together. Then you’ll…
Read the complete tip →From the archive · Full text
Reader shop tip
Don Jaster, Bruce, Wis.
“In your last issue, two separate readers complained about Deere riding mower features that stop the mower blades when you shift into reverse. My advice is to just take a look at the wiring. Riding mowers are generally…
Read the complete tip →From the archive · Full text
Reader shop tip
Marvin Martin, Elkton, Ky.
“On a Wrangler 4500 loader the hoses wanted to rub as they went through the frame at the articulation joint. I double wrapped the hoses with a piece of ratchet strap and secured them with zip ties temporarily.…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Roger Podoll
After Roger Podoll’s Troy-Bilt tiller went through a flood, the coil was shot. He got the tiller going again with a 12-volt coil and a battery from a cordless drill.
Read the complete story →From the archive · Full text
Reader shop tip
Elwin Gingerich, Kalona, Iowa
“If you have a housing that needs a seal but the seal fits loosely because the housing is worn, get a 12-volt battery and a set of jumper cables. Attach the negative cable to the housing and the…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Fondy Auto Electric, Fond du Lac, Wis. (ph 800 236-2701; www.fondyautoelectric. com)
Fondy offers a large inventory of new and remanufactured starters, generators and alternators to fit any vehicle, including cars and light and heavy-duty trucks as well as motorcycles, ATV’s, and snowmobiles. They say that if they don’t have…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Garland Rainey, Winchester, Kty.
“Hairspray on battery terminals can keep them from corroding and draining the battery.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Garland Rainey, Winchester, Kty.
If you have a battery that’s already corroded, Coke can be used to get it clean.”
Read the complete tip →From the archive · Full text
Reader shop tip
James Minix, Morrison, Tenn.
“I was having trouble keeping plastic electric fence insulators from breaking prematurely on chain link fence due to sunlight causing them to get brittle and weak. So I got the idea to protect them by coating the end…
Read the complete tip →From the archive · Full text
Reader shop tip
Lee Vangsness, Decorah, Iowa
“I mounted an 8-ft. swinging arm on my shop wall to hold my wire welder spool. Works great, saves time.”
Read the complete tip →From the archive · Full text
Feature story
Featured source: Lawrence Goodman
“The rear headlight on my Dresser dozer didn’t work because of a bad wiring connection at the exterior screw on the housing. Because of corrosion, the screw head stripped when I tried to remove it. But instead of…
Read the complete story →From the archive · Full text
Reader shop tip
Jim Holt, Cincinatti, Ohio
“Harbor Freight recently sold 2,500-lb. electric winches for less than $50 each. I bought 3 and installed one each on my Cub Cadet mowers and golf cart. No more running to get the big tractor when they get…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
John Daugherty, Gray, Ga.
“Here’s how I made some insulating buckets to put over our outdoor faucets in the winter to keep them from freezing. I bent some wire into a cylinder, taped some newspaper around it, and put it in the…
Read the complete tip →From the archive · Full text
Reader shop tip
Jake Buit, Marshall, Va.
“If you have a nut and a bolt that you never want to loosen, dip the bolt threads in battery acid and tighten the nut. It will not loosen.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Marvin Anderson, Glyndon, Minn.
“My Harbor Freight sawzall wasn’t running right so I took it apart to find out why. The problem was the gearbox contained light-duty grease that looked like vasoline, allowing too much metal-to-metal contact between gears.
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
By By Jim Ruen, Contributing Editor
Featured source: Dramm
You can make commercial grade hose cut to the length you need with OEM-style crimped fittings. Dramm offers its commercial grade, abrasion and weather resistant, ColorStorm hose in up to a 330-ft. bulk reel. Cut the hose to…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Handee Clamp, LLC
This new tool is designed to attach nuts, bolts or hose clamps in hard-to-reach places where your hands or other bulky tools can’t reach. The powder-coated Handee Clamp measures 10 in. long by 5/8 in. wide and comes…
Read the complete story →From the archive · Full text
Reader shop tip
Eugene Pontius, Wheat Ridge, Colo.
“I put pancake syrup on clean battery posts. It prevents corrosion buildup.”
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Gary Swensen, Yankton, S.Dak.
“I bought a small 900-watt 2-cycle $99 generator with one outlet from Harbor Freight. It’s handy to carry around to run a battery charger, small air compressor, and lights when out in the field. I used to keep…
Read the complete tip →From the archive · Full text
Reader shop tip
Gerald Ripps, San Antonio, Texas
“I’ve had trouble with Curt wire harness connectors. I had loss of continuity on 2 different 6-way sockets. Internally, the wire end screw connector disconnects from the plug end. I wasted a lot of time checking for power,…
Read the complete tip →From the archive · Full text
Reader shop tip
Kevin Wideman, Russellville, Mo.
“I don’t have a shop, so I built this outdoor workbench. I use my loader tractor’s forks to move the bench around. The photo shows how I can use the bench to haul my generator out to a…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Edward Fett
If you’ve got an old drill no longer in use, the chuck can be used to make a solid handle for a file, suggests Edward Fett, Lennox, S. Dak. He removes the chuck and spur gear from old…
Read the complete story →From the archive · Full text
Feature story
Featured source: Hastings Equity Mfg.
This reinforced self-adhesive repair patch is activated by ultraviolet light so it works fast. The DurapatchUV patch is made from reinforced polyester and comes with a white backing tape over the adhesive. You just clean the damaged area…
Read the complete story →From the archive · Full text
Reader shop tip
Kevin C. Jones, Bradford, Ohio
“When you throw away an old dishwasher, keep the bottom rack. It’s great for organizing various sockets and wrenches
Read the complete tip →From the archive · Full text
Reader shop tip
Tom Cogger, Washburn, Wis.
“I always used to have trouble with crimped wire connectors not holding. Inevitably, I’d crimp them and then they would fall off when I went to attach the wire. I came up with an easy fix. Take a…
Read the complete tip →From the archive · Full text
Reader shop tip
Norman Bennett, Newport, Vt.
“One of the remotes on my tractor stopped working and the dealer wanted $2,500 to install new ones. I solved the problem with a Summit Manufacturing outlet multiplier that I bought on Amazon for about $450. Everything you…
Read the complete tip →From the archive · Full text
Reader shop tip
Ron Nahrwold, New Haven, Ind.
“While I was changing oil in my New Holland L220 skid loader, the oil fill cap fell underneath the engine and I spent hours trying to retrieve it. To make sure I don’t lose the cap again, I…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
EverGreen Restoration, Spooner, Wis. (ph 715 520-7876; www.evergreengauges. com)
They recover old tractor steering wheels, using a manmade rubber material that doesn’t leave marks or residue on your hands. They can recover both flat and round spoke wheels. Prices range from $95 for 14, 15, and 17-in.,…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Donald Chapman, Billings, Mo.
“I use inexpensive dog collars purchased from our local Dollar Store to hold cords, tow straps, and cargo ratchet wraps together for tidy storage. You can buy different size collars and adjust them to fit. The collars come…
Read the complete tip →From the archive · Full text
Reader shop tip
Mark Gillen, Sterling, Mich.
“We use a number of small electric fans around the farm that run day and night, sometimes for months at a time. The bushings get dry and sometimes the fan won’t restart after being shut off. To keep…
Read the complete tip →From the archive · Full text
Reader shop tip
Milton Webster, Taylor, Texas
“I’m a small engine mechanic, and over the years have noted that the solenoid shift starters on riding mowers sometimes make a ‘clicking’ noise caused by a hot battery. Many people think the clicking noise means the solenoid…
Read the complete tip →From the archive · Full text
Reader shop tip
Ronnell Ott, Manhattan, Kan.
“By mounting the stator from a discarded permanent magnet motor onto a wooden plate, I can use it to store small magnetic parts such as drill bits or even sewing pins and needles. I remove the stators from…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Thomas Kane, 5131 Sand Road S.E., Iowa City, Iowa 52240 ph 319 358-8107
“I came up with a handy tape measure clip that lets you more securely fasten a standard tape measure onto any pants belt. It’s made from a no. 8 wire that’s bent where the belt goes through it.…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Glenn Alpert
Sharpening chainsaw chains is faster and more accurate for Glenn Alpert since he added lines on his vise.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Cory Miedema
If you have an engine you need to keep running even in the coldest temps and it’s a long way from electric power, Cory Miedema has a solution. Universal Engine Heater Company has been heating off-grid, engine blocks…
Read the complete story →From the archive · Full text
Feature story
Featured source: Bill Knutson
Slipping a Chevy 350 into Bill Knutson’s 1555 Oliver required nothing more than a little work with a grinder. When he first set it into position, it didn’t quite line up with the transmission input shaft.
Read the complete story →From the archive · Full text
Reader shop tip
Dave Doherty, Lebanon, Ore.
“I made a simple overhead lift by mounting a 4-in. I-beam in my shop fitted with a trolley and an electric hoist from Harber Freight. Very handy for picking up heavy stuff like mowers, ATV’s, and car engines.”
Read the complete tip →From the archive · Full text
Reader shop tip
Dave Mertell, Independence, Mo.
“The intake heater on my Case 350D crawler broke, making it hard to start cold. The price of a new heater was too high to justify so my son purchased a length of coilwire and I brazed it…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Dave Burgei
“Our new flange bushing kit for planters makes old and worn parallel linkage arms and bushings work better than new. All the wear takes place on replaceable parts instead of on your planter’s parallel linkage arms,” says Dave…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: PacPro Performance Parts
If you’re tired of dismantling half your Dodge pickup just to change the oil, you’ll like the new PacPro oil filtration relocation kit that moves the oil filter out into an open area for quick, hassle-free oil changes.
Read the complete story →From the archive · Full text
Reader shop tip
Michael Mayer, Smithshire, Ill.
“I was having trouble pouring tire balancing beads through valve stems into tires. I couldn’t pour, push or blow them into the tire until I started holding the side of an electric hair clipper against the metal part…
Read the complete tip →From the archive · Full text
Reader shop tip
Quinton Parker, Fairbanks, Alaska
He’s a diesel mechanic at a shop that works with heavy diesel equipment such as loaders, bull dozers, and semi trucks.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Raymond Rodriguez, Waxahachie, Texas
“To avoid hitting electrical wires when drilling into walls, I just slip a small piece of pipe over the drill bit to keep the bit from going in too deep. Just make the
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Raymond Rodriguez, Waxahachie, Texas
“I also came up with a way to use a regular electric drill as an impact wrench. I take a short socket wrench extension and cut off the end that fits over the socket wrench. Then I slip…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Richard Liberda, Mandan, N. Dak.
“Mike also fixed my wife’s wheelchair. The wiring was shot so I took it to two places in town but they wanted a lot of money to rewire the chair. Mike just cut off the ends of wires…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Steve Shield, West Liberty, Iowa
“I bought a Depstech endoscope on Amazon for $38 and can’t believe how useful it is. It’s a 33-ft. length of tubing with a camera on the end that I’ve used to inspect dryer vents, plugged drains (it’s…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Gene Boehler
Gene Boehler made an aerosol paint can “shaker” that makes use of an old cordless Ridgid sawzall, attaching a homemade shaker to the sawzall in place of the blade. A hose clamp attaches the can to the shaker.…
Read the complete story →From the archive · Full text
Reader shop tip
“I sell a conversion kit that uses gear reduction starters to convert the 2-cyl. diesel engines on Deere tractors to electric start. It’s designed for Deere 70, 720, 730, 80, 820, and 830 models. Switching to a 12-volt…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Warn Industries
You can use a cordless drill to power this portable, lightweight winch that you can take anywhere. The Warn 500-lb. capacity winch comes with 30 ft. of wire rope with front and rear rigging hooks. A free spool…
Read the complete story →From the archive · Full text
Reader shop tip
John Engle, Sunman, Ind.
“Here’s a tip I learned a long time ago for an easy way to check points to see if you’re getting a good spark without turning the engine over with a key. Just pull the distributor cap and…
Read the complete tip →From the archive · Full text
Reader shop tip
Jim Shover, Somerset, Ohio
“I bought a Harbor Freight battery-powered polesaw and spotted a small hole near the nose of the bar that was not mentioned in the owner’s manual. I called the company and they said it’s a ‘micro grease port’…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Eric Porch
If you have a wiring harness that’s burned or otherwise damaged, Porch Electric can rebuild or replicate it. The company specializes in not just harnesses, but also in everything electric for tractors – mostly of the IH variety,…
Read the complete story →From the archive · Full text
Reader shop tip
Doug Clark, Ilderton, Ontario
“A reader in your last issue said his Kubota L3130 diesel would not start on a real cold day if it had already been warmed up and then shut off – unless he leaves it long enough for…
Read the complete tip →From the archive · Full text
Reader shop tip
Frank Schafer, River Falls, Wis.
“Romex electrical wire works great to tie up anything that needs to be tied down. I use it to tie livestock gates and panels together when moving them, among many other things. It holds its shape and is…
Read the complete tip →From the archive · Full text
Reader shop tip
John Grady, Northern Ohio Truck Center, Inc., Norwalk, Ohio ph 419 668-4826 or cell ph 419 577-1408
He offers 12-volt gear reduction starters for Deere 70, 720, and 730 diesel 2-cyl. tractors as well as Deere 80, 820, and 830 models. Prices start at $995 to replace a pony start motor. A 12-volt starter for…
Read the complete tip →