Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW

Electrical

928 shop tips and stories · page 15 of 16, newest issues first.

From the archive · Full text
Reader shop tip

Avre Papst

Avre Papst, Fullerton, Neb.

“There are a lot of ways and a lot of products available to treat corrosion on battery posts, but there’s nothing else like the product I sell. When used as directed, one application will prevent corrosion on posts…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Dan Petersen

Individual tip 1 of 2 from this reader’s published contribution.
Dan Petersen, Curtice, Ohio

“I need help. The battery on my Massey Ferguson 180 tractor won’t charge. Everything electrical has been replaced, from the alternator to the gauge. It still won’t work.

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Kevin McWilliams

Individual tip 1 of 2 from this reader’s published contribution.
Kevin McWilliams, Columbia, N.J.

“We changed out Deere 3020 over to 12-volt electric from 24-volt and used a Delco alternator to replace the original generator system, which never charged enough to keep the batteries fresh.

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Kevin McWilliams

Individual tip 2 of 2 from this reader’s published contribution.
Kevin McWilliams, Columbia, N.J.

“I made cheap TIG (heli-arc) wire for cast iron by sanding the old coating off some stickwire ni-rod. It had become wet and the coating was chipping off. It made perfect TIG wire, which I would otherwise have…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Ken Turbett

Individual tip 1 of 2 from this reader’s published contribution.
Ken Turbett, Winnipeg, Manitoba

“I have a 20-ft. wide solid frame cultivator. Somehow, the rockshaft got twisted so there was a 4 to 5 in. difference in cultivating depth from one side to the other. To solve the problem, we mounted 14-in.…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 3

Loren Konda

Individual tip 2 of 3 from this reader’s published contribution.
Loren Konda, New Effington, S. Dak.

“When joining a couple wires where it’s too hard to get tape around them, I just solder the wires together and coat them with silicon or liquid plastic. Works great.

Read the complete tip →
From the archive · Full text
Reader shop tip

Jerome Bruha

Jerome Bruha, Comstock, Neb.

“The only complaint we have with our 1986 OMC 590 baler is that the #80 roller chain is re-ally a pain to repair because the spring loaded idler won’t loosen completely. Rather than take the idler completely apart,…

Read the complete tip →
From the archive · Full text
Reader shop tip

Roland Beckmeyer

Roland Beckmeyer, Hoyleton, Ill.

When Roland decided to add flashing safety lights to the back of his machinery, he decided to use battery-operated units rather than running wire to operate 12-volt lights. This way he can transfer one set of lights between…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Don Booth

Individual tip 1 of 2 from this reader’s published contribution.
Don Booth, Leoville, Sask.

“I had a problem with erratic operation of the Powershift on my 1986 Case-IH 4494 tractor. The dealer couldn’t fix it and the company service rep was no help either. I finally found the problem myself - bad…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Tom Graham

Individual tip 1 of 2 from this reader’s published contribution.
Tom Graham, Henderson, Minn.

“Instead of removing the straw chopper on Massey Ferguson 300, 410 and 510 combines when switching from corn to beans, I remove the front two bolts and hinge the chopper down on the back two bolts, then put…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

William C. Reeks

Individual tip 1 of 2 from this reader’s published contribution.
William C. Reeks, Cromwell, Kent.

“Here are two grease gun ideas that work for me. I wire a small plastic pill bottle to the handle of my gun where I can slip the nozzle of the gun when not in use. Keeps the…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

William C. Reeks

Individual tip 2 of 2 from this reader’s published contribution.
William C. Reeks, Cromwell, Kent.

The other idea is the way I converted a hand grease gun to a foot-pumped grease gun. I added extra hose to the gun, mounted it on a board with U-bolts, and made a toe stirrup out of…

Read the complete tip →