Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Prazi, Inc., 214 South Meadow Road, Plymouth, Mass. 02360 ph 800 262-0211 or 508 747-1490; www.praziusa.com
This company offers an “at-your-fingertips” hammer holder that eliminates “leg bang”. Prazi’s Hammer Holster clips onto any tool or waist belt with the hammer head inside the holster. When you’re ready to use the hammer, you grab the…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Clifton Wilburn
Cleaning dirty air filters is an easy job with this new air filter cleaner that uses a blast of air to instantly clean filters.
Read the complete story →From the archive · Full text
Reader shop tip 3 of 6
Individual tip 3 of 6 from this reader’s published contribution.
Bill Reeks, Cromwell, Ky.
“After emptying out 1-quart oil bottles, I shove their necks into a 1-gal. jug to catch whatever oil is left in the bottles. I use the collected oil in squirt oil cans.
Read the complete tip →From the archive · Full text
Reader shop tip 4 of 6
Individual tip 4 of 6 from this reader’s published contribution.
Bill Reeks, Cromwell, Ky.
“A V-belt formed into a loop, and with a washer slipped over it, works great for lifting and moving small logs.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Brad A. Hurst, Sr., Cresco, Iowa
“I always have problems taking tires off wheel rims. I find that when I spray the edge of the tire with WD-40 the tire will come right off later. It also makes the tire easier to mount because…
Read the complete tip →From the archive · Full text
Reader shop tip
Weldon Thomasson, Fredericksburg, Va.
“Here’s a trick I learned from my co-workers. If a bolt breaks off in any part, use a dremel tool equipped with a thin cut-off blade to cut a slot in the broken bolt. Then use a screwdriver…
Read the complete tip →From the archive · Full text
Reader shop tip
Charles M. Whitman, Cooperstown, Penn.
“I use Epson salt to prolong the life of batteries. I put one teaspoon in each cell, once a year with water to the proper level. It really makes a difference.”
Read the complete tip →From the archive · Full text
Reader shop tip
Art Gomez, Scott City, Kansas
“To change out a fuel pump on a 1986 GMC 305 V8, I cut out a piece of pliable plastic wide enough to fit in the engine block slot to hold the pin in place. I tried grease…
Read the complete tip →From the archive · Full text
Reader shop tip
Keith Switzer, Cromwell, Minn.
“I keep several sets of cheap tools around for difficult repair problems. That way, if I have to bend a tool or cut one off, I haven’t ruined an expensive tool. It’s surprising how often I use them.”
Read the complete tip →From the archive · Full text
Reader shop tip
Alton Ridings, Hazel, Ky.
“I have discovered that Sta-Bil fuel stabilizer liquid works great to ‘unstuck’ motors. It’s better than penetrating oil, in my opinion.”
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Buddy Hoopes, Beloit, Ohio
“I converted an ordinary grain bin lid into a handy, rolling ‘tote pan’. It works great for everything from changing oil to holding tools and bolts. I got the lid from the company I work for as they…
Read the complete tip →From the archive · Full text
Reader shop tip
David A. Miller, Smicksburg, Penn.
“I was in the middle of a spray job with my Wagener Spray Tech sprayer when it quit working. I discovered it had a dry rotted seal, and I didn’t have any replacement seals. So I put a…
Read the complete tip →From the archive · Full text
Reader shop tip
Doug Clark, Goderich, Ontario
“I mix automatic transmission fluid, either new or used, with kerosene 50 - 50 for use as a penetrating oil, air tool oil (new transmission fluid only), and cutting oil for our drill press and lathe. It also…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Frank Dyck, La Crete, Alberta
“I hung an 18-in. long piece of plastic pipe with a length of rope through it to make a sling above my vise to support baler belting while I relacing a torn belt. Very handy.”
Read the complete tip →From the archive · Full text
Reader shop tip
Jason Jay, Fort Ripley, Minn.
“I use canning wax to loosen rusted bolts, pipes, and nuts. I just heat up the part and then push wax onto the threads. It lubes the threads and makes everything easier to take apart. It’s an old…
Read the complete tip →From the archive · Full text
Reader shop tip
John W. Apple, Middletown, Ohio
“If you need to solder a copper pipe but can’t get water to stop dripping where you want to solder, here’s an idea. Push bread into the pipe until the water stops dripping. The bread will eventually dissolve…
Read the complete tip →From the archive · Full text
Reader shop tip
Ron Stadler, Monroe, Mich.
“I have a lot of feed bags to tie and I didn’t want to have to cut string off a ball of twine all the time. So I came up with an idea that lets me quickly make…
Read the complete tip →From the archive · Full text
Reader shop tip
Victor Daniels, Sterline, Mich.
“I find that Turtle Wax bug and tar remover ‘wipes’ work great for cleaning fluorescent light bulbs. The wipes will take off the glue from the price stickers and labels on new bulbs.”
Read the complete tip →From the archive · Full text
Reader shop tip
David A. Medley, Gordon, Ga.
“For engines that have been sitting for a long time and that are hard to crank, I use a propane torch (not lit) at the intake area. The propane gives the engine enough boost to start.”
Read the complete tip →From the archive · Full text
Reader shop tip
Dennis Rood, Clarksville, Ark.
“When disassembling an antique 3 hp gas engine for restoration, I found that a very large 3-jaw puller would only remove one flywheel. Standing the crankshaft on end in a 30-ton press made short work of it.”
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Don W. Thomas, Eureka, River, Alberta
“I’ve read several times in FARM SHOW about using melted wax to loosen stubborn bolts. Last summer I had two occasions to try the idea and I was amazed how well it worked.”
Read the complete tip →From the archive · Full text
Reader shop tip
Gary B. Miller, Peru, Ind.
“Cleaning rust or dirt from bolt holes with your taps will dull the taps. Instead, use a cut-off wheel to cut notches in hard bolts to do the cleaning. This works just as well and it saves your…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Joe Eilert, Jewell, Kan.
“Installing bulk oil tanks with hose reels and electronic meters has been very convenient and time-saving for us. We have tanks for both engine and hydraulic oil.”
Read the complete tip →From the archive · Full text
Reader shop tip
No-Spill Research, Inc., P.O. Box 11040, Kansas City, Mo. 64119 (ph 816 454-3389; fax 816 454-4158; www.no-spill.com/CARBcans.htm
This company offers fuel cans with spill-proof spouts. Flow rate is up to 3 gpm. The self-venting nozzle stops the flow of fuel when the target tank reaches full. The can has a single opening for filling and…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Bob Vasichek
“Our new magnetic socket inserts work great for holding bolts in hard-to-reach places,” says Bob Vasichek, Vasichek Enterprises, Michigan, N. Dak.
Read the complete story →From the archive · Full text
Feature story
Featured source: Posi Lock Puller, Inc.
This new 12-ton hydraulic “puller” has a built-in hydraulic pump that takes the work out of pulling even the most stuck-on bearing, bushing, gear, wheel or pulley,” says Posi Lock Puller, Inc., Cooperstown, N. Dak.
Read the complete story →From the archive · Full text
Reader shop tip
D&S Hydraulics, 605 Highway 75 North, Moorhead, Minn. 56560 ph 218 236-6135; www.dshydraulicsmn.com)
D&S repairs all makes and models of hydraulic pumps, motors, hydrostatics, valves and cylinders. They also custom-make cylinders from 1 1/2 to 6-in. bore with a 1 to 60-in. stroke. Ends can be customized for any unique application…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Elmer Pinkerton, Elmwood, Neb.
“The big bronze bearing failed in the rear of my Craftsman drill. In the past I might have tossed it but this time I took all the measurements to my bearing outlet and they had a perfect match…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Elmer Pinkerton, Elmwood, Neb.
“To lubricate a roller chain that will not be exposed to dirt, I mix 80 weight gear oil with an equal amount of gasoline. Apply with a brush and it will stay on there for a very long…
Read the complete tip →From the archive · Full text
Reader shop tip
Kimball Midwest, Columbus, Ohio ph 800 233-1294; www.kimballmidwest.com)
This company stocks more than 35,000 cutting tool maintenance and repair items, with a special order department having access to more than 300,000 hard-to-find parts. They offer a complete line of high performance cutting tools including super primalloy…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
John Needham, Nipissing, Ont.
“Here’s another tip. If you need to tighten a wooden handle, soak it in antifreeze instead of water because water will rot the wood.”
Read the complete tip →From the archive · Full text
Feature story
Featured source: Taylor Taylor
We got a phone call the other day from a fellow in Texas with the unusual name of Taylor Taylor. He’s the president of Worthy Manufacturing, a direct-from-the-factory manufacturer of sand blasters.
Read the complete story →From the archive · Full text
Reader shop tip
This company has developed a compact Fuel Purifier that it says removes more than 99 percent of water and more than 95 percent of the natural contaminants in diesel fuel. The two-stage fuel treatment system results in increased…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Mike Hoy, Hedrick, Iowa
“I use Sea Foam fuel additive in all my small engines. It keeps fuel fresh and engines running smooth. I dump a few ounces in the gas tanks in the fall and, come next spring, they start right…
Read the complete tip →From the archive · Full text
Reader shop tip
This company makes a product called VinylClear that’s designed to keep your home’s siding clean for years.
Read the complete tip →From the archive · Full text
Reader shop tip
Stuart Gunness, 6220 165 th Ave. S.E., Walcott, N. Dak. 58077 (ph 701 372-3761)
“I overhauled the pivot arms that hold the double disc seed openers on my 1992 Deere 9300 40-ft. drill. I used bolts and bushings instead of replacing the original rivets. The problem is that when the rivets wear…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Pollock Retrofix, Inc.
After a two years of use, a farmer-designed seal kit appears to be a good fix for a problem which has plagued owners of Deere 1850 Air Seeders produced from 1996 to 1998 and the Deere 750 No-Till…
Read the complete story →From the archive · Full text
Feature story
Featured source: Elmer Bearinger
If you need parts for a moldboard plow, there’s a good chance Elmer Bearinger has what you need.
Read the complete story →From the archive · Full text
Reader shop tip
Merton Russell, Endeavor, Wis.
“I read with interest your article on high performance paddles for New Holland forage harvesters (Vol. 30, No. 1). The high performance paddles simply bolt on in place of the original ones. New Holland has had problems with…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Arco Rosenow, Chillicothe, Ill.
“To keep wasps and spiders out of the hose connector on air tools, press on a 1-in. long, 1/2-in. dia. plastic pipe with an end cap. The cap will also protect the threads from being damaged.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Arco Rosenow, Chillicothe, Ill.
“To protect hack saw blades and files, put them inside a length of 3/4-in. dia. plastic pipe. You can also wrap several feet of duct tape around the pipe for a convenient way to carry the blades and…
Read the complete tip →From the archive · Full text
Reader shop tip
John Johnson, Paradise, Mont.
“There’s no better product to free up rusted bolts, springs, and other parts than Kroil, a penetrating lubricant from Kano Labs (www.kanolabs.com; ph 800 311-3374 or 615 833-4860). It’s better than WD-40 by a long shot. I’m not…
Read the complete tip →From the archive · Full text
Reader shop tip
Arco Rosenow, Chillicothe, Ill.
“Standing on a concrete floor at my work bench for extended periods of time made my legs and feet ache. To solve the problem, I made a wood block floor out of wood scraps.
Read the complete tip →From the archive · Full text
Reader shop tip
Michael Ray, Bloomington, Indiana
“In your last issue, Cal Yapp, Littleton, Mass., reported that his 1988 Jeep Cherokee runs until it gets hot, then stalls and won’t start. Try changing the fuel relay on top of the right fender under the hood.…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Tyco Plastics and Adhesives, 25 Forge Pkwy., Franklin, Mass. 02035 (ph 800 248- 7659; www.tycoadhesives.com)
The world’s largest manufacturer of duct tape now offers tape in oversize rolls. Unlike regular duct tape, the 12-in. by 30-ft. rolls have a paper liner that you peel off. It even comes with a slicer. It’s not…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
WD-40, P.O. Box 80607, San Diego, Calif. 92139 (ph 888 324-7596; www.wd40.com)
Now you can carry WD-40 with you all the time without having to carry a can around. The WD-40 No-Mess Pen carries .26 fl. oz. of the all-purpose lubricant. The felt-tipped applicator can be used to lubricate hinges…
Read the complete tip →From the archive · Full text
Reader shop tip
Gast Mfg. Inc., P.O. Box 97, Benton Harbor, Mich. 49023 ph 269 926-6171; www.gastmfg.com
This company offers a wide variety of air-powered motors. Typical applications include mixing equipment, conveyor drives, pump drives, hoists and winches, and hose reels.
Read the complete tip →From the archive · Full text
Feature story
Featured source: Kleenoil
We heard from another reader who told us he couldn’t be happier with his add-on oil filter system from Kleenoil. It removes dirt to 1 micron in size, water to 0.05%, and virtually any wear particles that work…
Read the complete story →From the archive · Full text
Reader shop tip
Arco Rosenow, Chillicothe, Ill.
“To make a rip and cross cut guide for panels, start with a piece of 1/4-in. thick plywood that’s 8 ft. long by 12 in. wide. Set your power saw on the plywood like you’re going to rip…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Doug Bonno, Iron River, Mich.
“Here’s an easy way to remove broken bolts from castings. Drill it out slightly under size and use a file to make three notches through the threads, then pick out the three pieces of the bolt. The threaded…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Doug Bonno, Iron River, Mich.
“I came up with my own overhead hoist system by using two in-ground hoists from an old gas station that was being torn down.”
Read the complete tip →From the archive · Full text
Reader shop tip
Elden D. Parkkonen, Champion, Mich.
“After decades of working on everything from stuck pulleys and stiff chains to frozen nuts and bolts, I finally came up with a method of freeing them up that works. I use a propane torch and an old…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
H.J. Trahan, Jennings, La.
“I attached an old Ford starter to a Wisconsin V-4 air-cooled engine that powers an air compressor. In the past I had to hand crank the engine. It was a touchy job to line up the gears.”
Read the complete tip →From the archive · Full text
Reader shop tip
Hold-It, Inc., 3724 FM 1960 West, Suite 300D, Houston, Texas 77068 (ph 281 440-1655; www.hold-it.net)
If you hate losing those little straws that come with aerosol cans, such as WD-40, you need a Hold-It. They’re stretchable plastic “lassoes” that hold the straw to the can. An envelope of 12 sells for $4.99 plus…
Read the complete tip →From the archive · Full text
Reader shop tip
James Brooks, Homer, Ga.
“Getting a flat tire on a tubeless rim presents a challenge, because after the tire is repaired it’s hard to seat the tire on the rim. I just use a come-along wrapped around the center of the tire…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Mark S. Yax, Solon, Ohio
“Before using an aerosol can that has an extension tube to concentrate the spray in a certain area, I insert the tube and then apply a drop of super glue to the joint where the tube meets the…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Mark S. Yax, Solon, Ohio
“When dismantling a large shipping crate, I was having a hard time removing the old nails with a claw hammer. I found that a drop of oil placed on the exposed shanks of the nail made pulling out…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Michael Ray, Bloomington, Ind.
“Maxima chain wax works great for motorcycle chains, as well as for linkages and hinges, etc. This product is paraffin based so it won’t fling off. It sets up good and stays put.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Richard Faber, Tiffin, Ohio
“I had a drill press on a small table that I couldn’t raise or lower. So I took a bumper jack, clamped it at the top and bottom to the drill stand, and use that to raise and…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Walter Fuoss, Oakley, Mich.
“To make it easier to start my wood splitter in cold weather, I put a styrofoam box around the engine and hydraulic pump. Then I placed a Halogen light under the box for an hour or so to…
Read the complete tip →