Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Martin Sauer, Eagle River, Wis.
“I made a low-tech underbody wash for our fire department. With all the road treatments here in northern Wisconsin, we wash the underside after just about every call. Most of the components were acquired from dumpster diving. I…
Read the complete tip →From the archive · Full text
Reader shop tip
Matthew Whyatt, Charlo, Mont.
“I had to remove the CV axles from an older side by side that were rusted and seized to the differential. I don’t have a slide hammer, so I looped a strap around the axle between the upper…
Read the complete tip →From the archive · Full text
Reader shop tip
Peter J. Cummings, Jeffersonville, N.Y.
“I used a small fine tap to clean out a female trailer electric plug. I held onto the plug with small vise grips.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Shannon Duffy
“Oil Away™ is a dry, enzyme-infused powder formulated to remove petroleum-based stains from unsealed concrete surfaces without the need for scrubbing, pressure washing, or even water,” says Shannon Duffy, COO at Oil Away.
Read the complete story →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Anonymous, Pa.
“Everyone but me probably knows this, but R4 industrial tires don’t get near the traction of ag tires in the field, similar to the difference between summer and winter tires in snow.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Anonymous, Pa.
“Try the rubber tarp straps with holes every 4 in. along the length. They’re so convenient that you’ll want to throw away the ones without holes.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Anonymous, Pa.
“I wanted to move several small items a long distance in my Ford F-150, which only has tie downs in the bottom corners of the bed. I threaded a light chain through anchors, pulled it tight, and tied…
Read the complete tip →From the archive · Full text
Reader shop tip
Dan Spinden, Fort Collins, Colo.
“I made my own paint booth by attaching clear plastic sheeting to the rafters. I unroll it whenever I have to paint a tractor or other equipment. It isolates my tools and equipment from overspray.”
Read the complete tip →From the archive · Full text
Reader shop tip
David Krapfl, New Vienna, Iowa
“Equipment jacks often get rusty outside. I put the jack in a drill press and bore several 1/4-in. holes through the outer and inner tubes, and then spray penetrating or lube oil through the holes onto the threaded…
Read the complete tip →From the archive · Full text
Reader shop tip
Eli Apple, Hillsborough, N.C.
“I bought a tool cart from Harbor Freight to use around my shop. It was a nice cart, but it wobbled a lot. I took 3/8-in. Grade-8 washers and put them between the casters and the metal. It…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Gary F. Thomsen, Arion, Iowa
“I used two bicycle hoists to lift my topper off my Ranger to install a bed protector. I replaced the hoist’s ropes with nylon ropes and mounted the hoist pulleys to 2 by 4s, slightly closer than the…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Gary F. Thomsen, Arion, Iowa
“A leak suddenly appeared on one horn loader cylinder, oil spraying in my face. I wrapped an old tube sock around the piston end of the cylinder. It still leaked, but not as much. I got my day’s…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Gary F. Thomsen, Arion, Iowa
“I mounted an electric 440-lb. hoist to an old hay track in the barn’s hay mow. It’s much easier to lift tires, wheels and other stuff upstairs. I replaced the ladder with salvaged stairs.”
Read the complete tip →From the archive · Full text
Reader shop tip
Herb Dunham, Millerton, Penn.
“Now on my 89th trip around the sun, I needed to add another step to get aboard my IH 300 utility tractor. So, I bolted an old buggy step below the original.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
John Rochester, Charlotte, N.C.
“When using stacked shims, it helps to bind them together with electrical tape so they stay stacked and don’t move around. This works on large and small shims with different shapes.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Ralph Volkman, Black Creek, Wis.
“When I sprung the arms on my tractor loader, I straightened them by picking up a heavy object with the high side. Then, I placed a post below the other arm. I carefully raised the front of my…
Read the complete tip →From the archive · Full text
Reader shop tip
Roger Kahler, Dunnell, Minn.
“When installing a rim on a hub without studs, cut the bead off a log bolt, taper the end and screw it into the top side of the hub. Then, hang the rim, install the other lug bolts…
Read the complete tip →From the archive · Full text
Reader shop tip
Samuel “Doc” Holloway, Riverton, Wyo.
“My International 606 with TA needed a clutch replacement. I used small strips of candle wax to align the two input shafts to go into the clutch.”
Read the complete tip →From the archive · Full text
Reader shop tip
Wallace Bengtson, Braham, Minn.
“When I have a frozen grease fitting, I use a short piece of 17-gauge electric fence wire to push in the stuck grease and move the ball inside.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
C.J. Shortridge, Dagsboro, Del.
“To protect fingers when using a 7-in. wafer wheel on a 4-in. grinder, I took the 4-in. guard and enlarged it to fit the 7-in. cutoff wheel. Much safer.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Fritz Groszkruger, Dumont, Iowa
“I made a swinging air, electric and light reel for the center of the shop between two overhead doors. It originally had bearings on the main pivot that I had to cut off. It rotated too easily. I…
Read the complete tip →From the archive · Full text
Reader shop tip
Gary Lobb, Makinen, Minn.
“When plastic grease fittings on PTO shafts are broken, use a needle point (designed for greasing sprockets on chainsaw bars) instead of the standard grease couplers. The needle point also works on broken or damaged grease fittings. You…
Read the complete tip →From the archive · Full text
Reader shop tip
Glen Ray Goodson, Galax, Va.
“I’ve read in FARM SHOW about people having problems with the teeth breaking on their Troy-Bilt walk-behind sickle bar mowers. I have a 1991 model and replaced the bar that holds the cutting teeth with one I took…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
J.L. Blue, Pinebluff, N.C.
“When you buy a can of boiled linseed oil, pour it into another empty can, leaving a small amount in the original can. Flip it on its side and use an old toothbrush to dip out oil for…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Jim Lacey, Dell Rapids, S.D.
“I checked the alignment on one of our trucks, and all the joints were tight. After jacking up the wheels, I cut a slot in a piece of Masonite, tacked it to a 2 by 6 cut at…
Read the complete tip →From the archive · Full text
Reader shop tip
John Cowell, Granath Mesa, Colo.
“For many years, I’ve used 1/2-in. two-hole conduit clamps (pipe clamps) to fasten wire to wood fence posts, using dichromate-coated ‘gold’ screws. This practice makes fence repair much easier. I use this system for smooth and barbed wire.…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Larry Goodman, Ionia, Mich.
“I purchased a piece of equipment that required a 12-volt battery for power. It had two clamps for positive and negative, plus two small alligator clips. I used battery post clamps for large cables. I cut down 3/8-in.…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Rick Nudd, Walworth, N.Y.
“When I disassemble and reassemble small things like carburetors, I do it in a cardboard box. This way, if a spring jumps or parts fall out, they are easy to find and retrieve. The box is clean, and…
Read the complete tip →From the archive · Full text
Reader shop tip
Steve Hood, Claremont, N.H.
“My gas-powered wood splitter leaked at the gasket that joins the carburetor to the engine. I rubbed hydraulic oil on the leak. It’s four years later, and I haven’t had any more issues with it.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Alan “Lindy” Linda, New York Mills, Minn.
“Tired of losing your chainsaw bar nuts out in the woods? Glue two small Alnico magnets to your saw. Lightly sand the backs of the magnets so the glue sticks better. Clean the glue surface well. I used…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Alan “Lindy” Linda, New York Mills, Minn.
“There’s often unused room under a shelf. Bend a piece of scrap metal for a custom-fit storage space.”
Read the complete tip →From the archive · Full text
Reader shop tip
Bruce Madden, Castleberry, Ala.
“I’m one of the many farmers that can’t back a four-wheeled wagon. I welded a 6-in. metal hitch on the front of my Polaris, and now I can drive it back under the shed.”
Read the complete tip →From the archive · Full text
Reader shop tip
Dave Krell, Kennewick, Wash.
“Regarding Husqvarna mowers/small engines: Don’t leave gasoline in small engines over the winter. Start them up, then drain the gas tank with a turkey baster after shutting the engine off. Then start them again and let them run…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Erik Hewitt, Hillsville, Va.
“In the past, when I would take my Deere 970 out to do some work, I always felt I should carry some chains. I would put them in a toolbox that rested behind my seat. When I needed…
Read the complete tip →From the archive · Full text
Reader shop tip
Greg Krush, Hotchkiss, Colo.
“When I moved my farm 300 miles, I used apple bins to move my shop with a forklift on each end. I didn’t have to pack tools, cylinders, etc. I just put them in apple bins and strapped…
Read the complete tip →From the archive · Full text
Reader shop tip
J.C. Macha, Plainview, Texas
“Silicone, duct tape, wire and an inner tube are all a farm shop needs.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Quinton Tschetter, Oskaloosa, Iowa
“Most of the things in my shop are on wheels so I can move them around as needed to make room for projects. However, some have only two wheels and can be quite heavy to pick up and…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Tommy Sanson, Red Wing, Minn.
“To get more life out of your old diesel, use engine oil mixed with new diesel, one quart to 10 gal.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Tommy Sanson, Red Wing, Minn.
“Use J-B Weld to repair threads and bad bearing shafts. Cut, resize and then turn down or sand down the shaft so the bearing fits tight.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Tommy Sanson, Red Wing, Minn.
“If you have a dirt floor, set a board on jacks to store batteries to protect them from the ground.”
Read the complete tip →From the archive · Full text
Reader shop tip
Gordon D. Myrick, Grand Coulee, Wash.
“I put ratchet straps inside PVC pipe to keep them untangled.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 8
Individual tip 1 of 8 from this reader’s published contribution.
Kent MacDougal, Yonges Island, S.C.
“Like many readers, FARM SHOW is my favorite publication. I’m glad to see I’m not the only one who braids baling twine. I built a cargo net with mine.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 8
Individual tip 2 of 8 from this reader’s published contribution.
Kent MacDougal, Yonges Island, S.C.
“Acetone and power steering fluid (50/50) make great penetrating oil.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 8
Individual tip 3 of 8 from this reader’s published contribution.
Kent MacDougal, Yonges Island, S.C.
Heating the nut and touching it with a candle also works to loosen a stuck nut or bolt.
Read the complete tip →From the archive · Full text
Reader shop tip 4 of 8
Individual tip 4 of 8 from this reader’s published contribution.
Kent MacDougal, Yonges Island, S.C.
“An iron rake head attached to the wall holds box end wrenches and sockets. Save the broken handle; they make great stakes.
Read the complete tip →From the archive · Full text
Reader shop tip 5 of 8
Individual tip 5 of 8 from this reader’s published contribution.
Kent MacDougal, Yonges Island, S.C.
“Soak tools that are rusted shut in water.
Read the complete tip →From the archive · Full text
Reader shop tip 6 of 8
Individual tip 6 of 8 from this reader’s published contribution.
Kent MacDougal, Yonges Island, S.C.
“I found that a 2-in. eye bolt fastened to the hitch of my lawn tractor let me pull my utility trailer easily. I never bent it, even with the trailer loaded.
Read the complete tip →From the archive · Full text
Reader shop tip 7 of 8
Individual tip 7 of 8 from this reader’s published contribution.
Kent MacDougal, Yonges Island, S.C.
“Cutting grooves in your mower blade (like a Ginsu knife) doesn’t make for a better cut; it only wears the blade faster.
Read the complete tip →From the archive · Full text
Reader shop tip 8 of 8
Individual tip 8 of 8 from this reader’s published contribution.
Kent MacDougal, Yonges Island, S.C.
“I beg everyone that uses old motor oil in their saws or as a stain to stop it. You can’t filter out dissolved solids. Burnt oil is carcinogenic. Dispose of it correctly.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Larry Wood, Waldo, Ohio
“I had trouble lining up the hitch pin on my receiver. So, I welded a stop block on the top of my hitch. I first put the pin in and then welded a 1/4-in. steel block on the…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Larry Wood, Waldo, Ohio
“I always carry my pintle hitch with me in my truck. But it was constantly sliding around in the truck bed. I came up with the idea of mounting it under the truck behind the bumper. I welded…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Larry Wood, Waldo, Ohio
“I pick up lots of equipment with my skid steer forks, but I was always afraid that my lifting straps or chains would slip off the end of my forks. I drilled a 1/2-in. hole near the end…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 4
Individual tip 1 of 4 from this reader’s published contribution.
Preston Williams, Victoria, Va.
“My Ford 2000 tractor would pour steam out the pipe valve cover to under the motor. I pulled the head and replaced the head gasket, and it’s okay now.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 4
Individual tip 2 of 4 from this reader’s published contribution.
Preston Williams, Victoria, Va.
“I used Flex Seal on tires that were cracked. It helped keep the dirt out. It’s a good temporary fix.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 4
Individual tip 3 of 4 from this reader’s published contribution.
Preston Williams, Victoria, Va.
“I welded a 6-in. by 1 1/2-in. piece of tubing to my loader bucket and hung my hay fork on it with a metal loop on the fork tip. I put it on or off easily.
Read the complete tip →From the archive · Full text
Reader shop tip 4 of 4
Individual tip 4 of 4 from this reader’s published contribution.
Preston Williams, Victoria, Va.
“I had a 6-in. piece of rebar stuck in my rear tractor tire. After removing it, I plugged it and covered it with Flex Seal, and it’s still holding.”
Read the complete tip →From the archive · Full text
Reader shop tip
Steven Hood, Claremont, N.H.
“The carb gasket on my wood splitter was seeping. I rubbed the area with hydraulic oil. It’s still good years later.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
William Ridgway, Salem, Ind.
“When a bucket is no longer repairable, it can make a good hose hanger with internal storage for spray heads and more.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Koen Meukens, Antwerp, Belgium
The handheld BLSTRsander removes paint, rust and more from wood, metal, glass and brick, no matter how complex the surface. Unfortunately, it’s not yet available in North America. The corded, no-compressor sandblaster solved a common problem faced by…
Read the complete story →