From the archive · Full text
Reader shop tip
Robert L. Kuhlmeier, Salina, Kan.
“I had a problem with the lift brackets on my Allis Chalmers 1300 field cultivator wings breaking when raising and lowering. I solved the problem with $50 worth of cable and brackets. It was a cheap way to…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Don Williams, Clarinda, Iowa
“I’ve found that by filling an oil filter full of oil before installing it on engines brings oil pressure up faster because it doesn’t have to travel through the filter before reaching the bearings. This reduces wear on…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Robert House, Grace City, N. Dak
“I also always brush Permatex anti-seize lubricant on new bolts when I’m putting engines back together. They come out much easier the next time.”
Read the complete tip →From the archive · Full text
Reader shop tip
Rod Rhoades, North Star, Alberta
Rod discovered a simple, no strain method of driving nails with an air hammer fitted with a straight punch attachment.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Chop Gibson, Scranton, Iowa
“I have a Sukup bin unloading auger that had trouble with the roller chain which kept jumping off. I replaced the sprockets with larger ones to try to solve the problem. It worked.
Read the complete tip →From the archive · Full text
Reader shop tip
Levi Adams, Locke, N.Y.
“I’ve discovered that pto shafts run better if you do not grease them as much as the rest of the machine it’s mounted on. Usually once for every three or four times is sufficient.”
Read the complete tip →From the archive · Full text
Feature story
Featured source:
You can sweat pipe joint in seconds with new double and triple flame torch tips that concentrate the flame directly on the pipe with no damage to the surrounding area.
Read the complete story →From the archive · Full text
Reader shop tip
John Adams, Cross Plains, Texas
He had trouble with dirt and dust getting into the couplings for his air compressor-powered impact wrenches, paint guns and other tools.
Read the complete tip →From the archive · Full text
Reader shop tip
Kirk Dahl, Ruby Valley, Nev.
“I scratch the date, engine hours and oil weight on each oil filter that I replace when changing oil. At a glance I know when to change oil again.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Linden Hankins, Bonanza, Ore.
“Freeman bale chamber slide bars have a tendency to get hay and dust behind them, making the plunger hard to adjust. When replacing the slide bars, I put a bead of silicone gasket adhesive behind them and along…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Paul Rusch, Nekoosa, Wis.
“I save money on bearings by purchasing them at one of two local bearing distributors for at least half the dealer price.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Paul Rusch, Nekoosa, Wis.
One tip on working with bearings: Heat expands and cold shrinks. Put a bearing in an oven at 200° to slide it on a shaft. Put it in the freezer to drop it into a bore.”
Read the complete tip →From the archive · Full text
Reader shop tip
S. Reppert, Reading, Mich.
“I take a round chain saw file and cut a notch on a pencil. Then I take half of a clothespin, with the spring in place, and I slip it down to the notch. This gives you a…
Read the complete tip →From the archive · Full text
Reader shop tip
Ben Meister, Fairbury, Ill.
Ben offers a low-cost solution to problems associated with drums jumping on certain Case-IH Cyclo planters when they’re used to plant corn.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Bill Reeks, Cromwell, Kent.
“I buy grease in bulk and have found that if I mix about a can of STP oil treatment into a gallon of grease, it feeds out of the grease gun a lot smoother and seems to do…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Bill Reeks, Cromwell, Kent.
“I’ve also had good luck filling a grease gun with rear end oil or manual transmission oil in order to pump the oil into hard-to-reach spots.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Bill Reeks, Cromwell, Kent.
I’ve also had good luck putting nuts, bolts and other small parts into plastic peanut butter jars. I carry a bunch of jars around in 5-gal. buckets. They don’t break and you can easily see what’s inside.”
Read the complete tip →From the archive · Full text
Reader shop tip
Jim Donald, Woodland, Wash.
“We’ve discovered that you can shake frozen rusted bolts and parts loose by using an air chisel with a dull bit to vibrate them. Ninety percent of frozen parts will come apart readily after vibrating them for a…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Joyce Miller, Independence, Kan.
“I’m 89 years old and still work 8 hrs. a day, 6 days a week and don’t plan to retire until I have to. My best maintenance tip for equipment is nothing unusual but it works: Just service…
Read the complete tip →From the archive · Full text
Reader shop tip
Milo Rifenberg, Hillsboro, W.V.
“You can make your own lock nut by screwing a nut halfway onto a bolt and then placing the nut on an anvil and distorting it with a large hammer. Then when you screw it down, it will…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Richard Siems, Melvin, Ill.
“My father took an old set of vice grips locking C-clamp pliers and fashioned screwdriver tips on the ends of the jaws. They’re perfect for removing grease caps from wagon hubs. Saves your hands.
Read the complete tip →From the archive · Full text
Reader shop tip
Stuart James, Hammond, Ill.
“When spraying weeds around my barn lots and farmyard with a hand-held sprayer, my back was taking the worst of it. I solved the problem by mounting the sprayer on a hand-pulled golf cart.”
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 6
Individual tip 2 of 6 from this reader’s published contribution.
Cary Urka, Brethren, Mich.
I also screwed a length of conduit onto the dash in order to make a handy flashlight holder.
Read the complete tip →From the archive · Full text
Reader shop tip
Henry E. Perrin, Barre, Vt.
Regarding the story on a hammer with a magnetized nail holding slot at the top that makes it easy to start nails (Vol. 20, No. 3), it sounds like someone is reinventing the wheel. Back in the 1940’s…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Bill Short, Hamilton, Mo
“Hacksaw-ing a groove in the side of grease fittings to relieve pressure as you fill bearings with grease is an easy way to prevent damage to grease seals. You just cut a groove along one side of the…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Ken Turbett, Winnipeg, Manitoba
“To make spin-on oil filter changes less messy, I use a nail to make air and drain holes in the filters before taking them off. The drawing shows where I make the two holes.”
Read the complete tip →From the archive · Full text
Reader shop tip
Bob Wooding, E. Greenbush, N.Y.
Bob says a farmer friend of his thinks the chain saw filing guide he made to clamp in his vise is the best thing since sliced bread.
Read the complete tip →From the archive · Full text
Reader shop tip
Gilbert O. Miller, Mitchell, S.Dak.
“To loosen frozen nuts on manifolds and rusted equipment, here’s a method I learned from an old mechanic years ago. Just heat the nuts until they’re red hot and then apply a piece of bees wax. It will…
Read the complete tip →From the archive · Full text
Reader shop tip
Bob Haddon, Belvidere, Tenn.
“I’ve found that pouring a little beer on a dull drill bit, before it starts smoking, will make it cut much faster. I have no idea why it works, but it does work, even when using beer from…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Floyd E. Ver Ploeg, Lovila, Iowa
“I save used oil and mix a quart or two of it 50-50 with gas to make the best penetrating oil anyone could ask for. I also use it as a cutting oil. Works great and costs little.”
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Landis Shelton, Webbers Falls, Okla.
I mounted a bolt on a bell crank equipped with a worn-out woodruff key. I drilled a hole on the opposite side of the key and screwed in a bolt to take the play out of the key.”
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Lighting a torch is as easy as flicking the end of it back and forth to strike the flint in “Safety Light” striker that clips onto the end of any torch.
Read the complete story →From the archive · Full text
Reader shop tip
Andy Szurek, Minneapolis, Minn.
“I had an old tire and wheel that wouldn’t come apart. I sprayed it with WD-40 and they came apart in 10 minutes.”
Read the complete tip →From the archive · Full text
Reader shop tip
Chris Brighoff, New Windsor, Md.
“To remove a stuck oil filter, I use a piece of sandpaper. Just put the grit side against the filter and turn.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
James D. Vaughn, Lyles, Tenn.
“To unstop grease fittings on your equipment, take out the fitting and squirt carburetor cleaner in it and let it set a minute. Then wipe it out and reinstall it. Really works good.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Lamar B. Fahnestock, Lebanon, Penn.
“I put a roller on the back of my loader bucket to prevent damage to our paved driveway when moving snow. The rollers extend down about 1/2 in. below the bucket.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Lamar B. Fahnestock, Lebanon, Penn.
“I also attached short sections of plastic pipe to my rear grader blade, also to pre-vent damage to driveway. I just cut a short slit in the pipe sections, slipped them on over the bottom of the blade,…
Read the complete tip →From the archive · Full text
Reader shop tip
Larry Evans, Ty Ty, Ga.
“Here’s a handy way to make height-adjustable, fold-flat sawhorses. I put a hinge at the top of one set of legs. A length of chain runs between the two sets of legs at the bottom. There’s an eye…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Loren Konda, New Effington, S. Dak.
“I’ve found a way to get rusted bolts loose that works a lot better than cussing. I mix equal parts of WD-40, carb cleaner, and brake parts cleaner and spray it on. Works every time. Just let it…
Read the complete tip →From the archive · Full text
Reader shop tip
Rob McDonald, North Lancaster, Ontario
“Our Rovibec feed cart would always plug up at the auger. We replaced the auger and it didn’t help at all. Dad and I were looking at it one day and noticed that the main apron chain seemed…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source:
New magnetic “socket inserts” hold nuts and bolts tight inside the socket, making it easier to reach out-of-the-way locations. The “Brocket” socket insert is a yellow plastic insert with a round magnet imbedded in the middle of it.…
Read the complete story →From the archive · Full text
Reader shop tip
Michael Risner, Knox, Ind.
“We’ve got two Case-IH Cyclo planters, a 500 (12-row) and a 900 (6-row). Both have trouble with seed spacing. That’s because the plastic wheels on each of the brushes wear out because there’s too much pressure on them,…
Read the complete tip →From the archive · Full text
Reader shop tip
Jeff Roberts, Needville, Texas
“Not long after I bought an old Deere 60 planter with round fiberglass hoppers, I began to notice wear spots where the hoppers rubbed against toolbar brackets every time I lifted the planter. Soon the hoppers were badly…
Read the complete tip →From the archive · Full text
Reader shop tip
Dennis Kees, Harlan, Ind.
“The trouble with the 3-in. twisted spikes on our 9-shank Glencoe soil saver was that in bringing up soil and residue in hard ground they tripped a lot, eventually wearing them down at the neck and breaking them…
Read the complete tip →From the archive · Full text
Reader shop tip
Harold Brewer, Lebanon, Tenn.
“A lot of guys say they have trouble starting small engines. I use WD-40 and I never have a problem. It fires quickly.”
Read the complete tip →From the archive · Full text
Reader shop tip
Phillip Myers, Nathrop, Colo.
“I’ve discovered that valve stems from old tubeless tires make good handles for small files, such as for sharpening chain saws.”
Read the complete tip →From the archive · Full text
Reader shop tip
Bill Irwin, Glade Valley, N.C.
“It seemed like the longer we used our fuel-powered space heater, the worse it would smell. I think it was from burning the same air over and over. I solved the problem by venting in outside air using…
Read the complete tip →From the archive · Full text
Reader shop tip
John C. Blundell, Papakura, Auckland, New Zealand
“Here’s an automatic air bleed valve I designed to pre-vent air lock in long water pipes. A short length of pipe runs straight up from the main pipe. There’s a vent hole in the top of the pipe…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Leonard J. Arenz, Streator, Ill.
“I repaired an exhaust leak on the combine with a muffler tail pipe bandage. For about $3.00 it worked great and saved a lot of money over replacing the pipe.”
Read the complete tip →From the archive · Full text
Reader shop tip
Rodger Parmelee, Valier, Mont.
“I made a ‘sizer’ to mount on the side of my cut-off saw that saves a lot of time when cutting several pieces the same length. It slides back and forth on a piece of pipe that sticks…
Read the complete tip →From the archive · Full text
Reader shop tip
Allen Reimer, Capron, Ill.
“We had a problem. Our cattle needed more vitamins. We mounted an insecticide-type Gandy attachment on the elevator that runs from the silo to the belt feeder. As the elevator runs, vitamins are dropped on the silage. We…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Andy R. Hodges, Galax, Va.
“One tough maintenance job I’ve got is putting bearings on the rollers of a New Holland Haybine. It’s extremely tough and time-consuming. I made it easier by using a torch to cut the old bearings off the shaft.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Chris Palmer, Enumclaw, Wash.
“I couldn’t unbolt a tie rod off the steering arm on my Massey 65. My 3/4-in. Craftsman expandable wrench broke but my Stanley Proto wrench took it off with a 3-ft. piece of pipe on it. The Proto…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Chris Palmer, Enumclaw, Wash.
“My best maintenance tip is to clean, clean, clean. If you keep your equipment clean, problems will show up easier - like oil leaks, cracks, and so on.
Read the complete tip →From the archive · Full text
Reader shop tip
Albert P. Weiss, Faith, S.Dak.
“To re-move oil filters without getting oil all over your hands, punch a small hole in the bottom of the filter to drain it out into a pail.”
Read the complete tip →From the archive · Full text
Reader shop tip
Bayard E. Young, Elkwood, Va.
“This is a simple idea but it works well. I use wide mouth plastic peanut butter jars to hold nuts, bolts and miscellaneous parts. You can see what’s inside and unlike glass jars, they won’t break if you…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
David M. Munson, Jr., Paris, Tex.
I also have a handy rolling workbench so I can bring all the tools right over by the job.”
Read the complete tip →From the archive · Full text
Reader shop tip
J.S. Adams, Cross Plains, Texas
“To protect air valves on impact tools from dirt, I use plastic hydraulic valve covers. Saves many hours of cleaning out dirt and prevents damage.”
Read the complete tip →From the archive · Full text
Reader shop tip
Kenneth Koenen, Burlington, Wis.
“The rear teeth on our Brillion Culti-Mulcher always acted like a rake, plugging up with residue. To solve the problem, we mounted Danish tines on the rear bar. They do the job yet let trash flow through. That’s…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Mark E. Hansen, Sherman, Ill.
“The wood decks on hay wagons wears out rapidly. I replaced mine with 1 1/4-in. thick treated deck wood that’s strong and should last over 20 years. It’s cheap in the long run because of the longer wear.”
Read the complete tip →