From the archive · Full text
Feature story
Featured source: Ron Post
Ohio farmer Ron Post says that on most equipment there’s always a stubborn zerk or two that won’t take grease, especially in the winter, and he’s gotten really tired of dealing with them.
Read the complete story →From the archive · Full text
Reader shop tip
Bayard E. Young, Elkwood, Va.
“After several years of use the coulters and double disc openers on my Tye 3-pt. mounted, 10-ft. no-till grain drill became wobbly due to worn-out sealed bearings, a problem that was caused by a lack of grease. Replacing…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Carrol Jones, Loiuisa, Va.
“I write the hours of installation onto the outside of oil filters with a paint pen when I install them. This helps us keep on top of oil changes.
Read the complete tip →From the archive · Full text
Reader shop tip
Jim Ruen, La Crescent, Minn.
“After a FARM SHOW reader sent in a tip for turning a flat tire into a flat-free tire by filling it with expandable foam (Great Stuff), I thought I would try it. I drilled holes like he said…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Lee Tolliver, Tok, Alaska
“Cutting plexiglass is always hard because the edges shatter and break. I recently came up with a method that works perfect. I just use a Dremel Multi-Tool with a small cutting disk. It cuts nice and clean, making…
Read the complete tip →From the archive · Full text
Reader shop tip
Bob Moty, Crystal Lake, Ill.
“Filling up my air transfer tank with air was always a hassle. I have Milton air couplers on all my pneumatic equipment so I took two Milton air coupler ‘plugs’ - one with a female 1/4-in. N.P.T. and…
Read the complete tip →From the archive · Full text
Reader shop tip
Cecil J. Nix, North Bend, Ore.
“My friend’s New Holland 630 round baler wasn’t tieing bales properly, and I spent 3 days searching for the problem with no luck. I was about to give up when I finally discovered a bolt holding the brake…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Eugene Mitchell, Gladys, Va.
“I save time by color coding wrenches with color tape, using the same color on all wrenches and sockets of the same size. For instance, I use yellow tape an all 1/2-wrenches, and other colors on other sizes.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Eugene Mitchell, Gladys, Va.
“Here’s a way to always get about 40 miles to the gallon running errands into town. Plan your trips! If you drive half as many miles to get the same amount of work done, you go from 20…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Gary Swenson, Yankton, S. Dak.
“This is just a handy hint. I have one car that’s very low to the ground so when I drive up on the ramps, the front end rubs on the ramps. So now I lay a piece of…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Jesse Barley, Tyrone, Penn.
“I’m 6 ft., 2 in. tall so most workbenches are so low I have to lean over to work on things. So I made my workbench 44 in. tall. It’s much more comfortable to use now.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
John T. Hayes Jr., Iron City, Tenn.
“I also made my own belt guides for my Deere 535 baler. Deere wanted $14 each. I made mine for less than $1 each. Painted them Deere green and they look like they came from the factory.”
Read the complete tip →From the archive · Full text
Reader shop tip
Melvin Doyle, Plummer, Idaho
“I have trouble breaking axle housings on my 350 hp. Versatile. It’s a model 700 with a big Detroit diesel. So far the only solution I’ve come up with to prevent this problem is to baby it on…
Read the complete tip →From the archive · Full text
Reader shop tip
Roger Stephens, Roundup, Mont.
“I broke the overflow nipple on the radiator of my 1989 S-10 Blazer so I drilled out the hole to the diameter of a 357 Magnum shell casing. I drilled out the primer hole on the casing to…
Read the complete tip →From the archive · Full text
Reader shop tip
Steve Belcher, Russell, Penn.
“My father-in-law showed me the great benefits of using Never-Seez compound on equipment. Anytime something breaks down around here, all the nuts and bolts are given a nice light coating of Never-Seez before I reassemble. If the equipment…
Read the complete tip →From the archive · Full text
Reader shop tip
Steve Mead, Hesston, Kan.
“We installed a service pit 5 ft. deep about 20 years ago. It’s covered by aluminum boards. We use it for changing oil and other repairs. The first oil change cost about $1,000. The second was $500. Eventually,…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Tom Haller
Tom Haller of Palmyra, Neb., recently responded to a story in our last issue on how a reader cleans greasy air filters on his Bobcat skid loader. The reader explained how he sprays a can of starter fluid…
Read the complete story →From the archive · Full text
Reader shop tip
Kurt Hofmeister, Woodburn, Oregon
“Trying to assemble anything with loose washers often can be a frustrating experience. So if the washer is loose, I just roll a small O-ring onto the bolt and use it to hold the washer in place.”
Read the complete tip →From the archive · Full text
Reader shop tip
Robert Lounsberry, Bordentown, N.J.
“The wooden block bearing on the feed auger of my Deere square baler dried out and was chattering so much that the noise was driving me nuts. To solve the problem, I added a grease fitting to the…
Read the complete tip →From the archive · Full text
Reader shop tip
David Prause, China Spring, Texas
“If you’ve got leaking transmission gearbox seals on your shredders or flail choppers, take the top off and fill partially with heavy gun grease. Check regularly after that and add the heaviest gear oil you can get just…
Read the complete tip →From the archive · Full text
Reader shop tip
Gary Swensen, Yankton, S. Dak.
“When I change oil, I wait until there are just a few threads left before the plug comes out and then I attach a vice grip to the plug to keep my fingers from getting burned. It also…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Lee Tolliver
“My Bobcat has a couple air filters on it that cost $26 to $27 apiece and when I’m on a job, I can go through a set or more in a week. I don’t like throwing them away…
Read the complete story →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Ben D. Marek, New Ulm, Texas
“I broke a hoe handle. To repair it, I used a hacksaw to cut a slot lengthwise in a 12-in. long piece of pvc pipe and slipped the broken ends of the handle into either end. I applied…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Bruce Buckmaster, Rogue River, Ore.
“To remove a seized pulley from a shaft, I heat the pulley and melt wax from a candle onto the heated pulley shaft. Then I can remove the pulley easily.
Read the complete tip →From the archive · Full text
Reader shop tip
Garry Hoffman, Killaly, Sask.
“Anyone who has ever used a 3-jaw puller knows how frustrating the experience can be. However, wrapping the jaws with a vise grip chain changes the whole experience.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Gary Alford, Edwardsburg, Mich.
“Fuel shut-offs on Ford 800’s always start leaking and replacements are getting expensive. You can remove the stop pin, replace the O-ring, and then tap in a small screw to take the place of the stop pin. This…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Kerry Kligora, Mineral Point, Wis.
“I cut a lot of wood for our boiler every year. At the end of the season, I sharpen all the chains and gauge all the rakes prior to storing, but sometimes they rust during the off season.…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Miles Parkkonen, Marquette, Mich. (www.paintscrubber.com)
His new Paint Brush Scrubber makes it easier to clean paint brushes, rollers and pads. The small, wooden tool has a grooved washboard surface. Brushes are cleaned by scrubbing them back and forth at a 45 degree angle,…
Read the complete tip →From the archive · Full text
Reader shop tip
R.A. Smith, Piketon, Ohio
“The power steering on my 2002 Sebring sedan was getting difficult to use. It would ‘stick’ at lower rpm’s. I talked to a friend who had the same problem with a 2007 Toyota Tacoma. His dealer wanted $1,200…
Read the complete tip →From the archive · Full text
Reader shop tip
Ray Webb, Emlenton, Penn.
“Here’s how I remove a 3/4-in. broken stud. First, I drill a 1/4-in. pilot hole in the end of the stud. Then I take a 1/2-in. right hand drill bit and run it in reverse to back the…
Read the complete tip →From the archive · Full text
Reader shop tip
Robert Sibley, Tioga, La.
“Both diaphragms on my Danner sewer system air pump ruptured. The replacement cost for a new pump was $450 plus labor. Instead, I found a repair kit on Amazon for $15. Did the job myself and it runs…
Read the complete tip →From the archive · Full text
Reader shop tip
Will Runyan, Avoca, Neb.
“I use silicon caulk to seal air lines and fittings on air compressors. After assembling with Teflon tape, I just apply with my finger around the leaky area. It works.”
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 4
Individual tip 2 of 4 from this reader’s published contribution.
David Prause, China Spring, Texas
“The baler’s sealed bearings used to heat up so I replaced them with greaseable bearings and give them a shot of grease every hour or two. I use a laser light monitor to check the bearings’ temperature. Now…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Jared Witmer, Monterey, Va.
“We replaced the original handle on our push broom with a long, adjustable paint roller handle. It consists of two telescoping tubes and can be easily shortened or lengthened by turning a ‘twist lock’ knob. The handle adjusts…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Steve Nichols, Galesburg, Ill.
“Joe Campoli submitted a nice idea in your last issue. He labeled his tire pressure gauge so he knows the recommended pressures for all his tires. However, I wonder how long it will take before the labels fade…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Ron “Skinny” Paustian
“I built this oil draining device to collect leftover oil from plastic oil jugs,” says Ron Paustian, Eau Claire, Mich. He cuts the bottom off 1-pint plastic fuel additive containers and turns them upside down to serve as…
Read the complete story →From the archive · Full text
Reader shop tip
Andrew Sewell, North Yorkshire, England
“I’ve got a big batch of keys that I carry around and a friend told me that I could lessen wear and tear on my car’s ignition by taking off some of the load. So I screwed a…
Read the complete tip →From the archive · Full text
Reader shop tip
Bill Crawford, Milford, Mich.
“I’ve read with interest a number of articles in FARM SHOW about guys who are venting their plastic fuel cans with tire valves. Instead of going to all that trouble, I drive a nail into the can opposite…
Read the complete tip →From the archive · Full text
Reader shop tip
Jonathan Dean, Baskin, La.
“I had trouble with the shifting mechanism on my International 1066. I removed the floor pan and installed two washers on the pushrod that goes to the shifter to remove slack. It really helped.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Raymond Hornak, New Berlin, Wis.
“When installing parts – such as mounting a water pump on an engine – cut the heads off a couple bolts that are about a half inch longer than required. Lightly screw these ‘studs’ into place to hold…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Ron Paustian, Eau Claire, Mich.
“To prevent hydraulic hose failure wherever the hoses rub on equipment, we save caulking gun plastic tubes and put them over the hose, using zip ties to hold them in place. These tubes are very durable. If they’re…
Read the complete tip →From the archive · Full text
Reader shop tip
Travis Cates, Troy, Ala.
“If I have a rubber drive belt that’s squeaking, I fix it by holding a bar of soap on the belt while it’s running.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 5
Individual tip 1 of 5 from this reader’s published contribution.
Herman Vander Vos, Bozeman, Mont.
“Thanks for printing my ‘worst buy’ report in Vol. 39, No. 6, about the bending of push rods in a Briggs & Stratton engine. Here are some suggestions I received from FARM SHOW readers: “1. Run engine at…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 5
Individual tip 2 of 5 from this reader’s published contribution.
Herman Vander Vos, Bozeman, Mont.
2. Use synthetic oil because it keeps the engine cooler.
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 5
Individual tip 3 of 5 from this reader’s published contribution.
Herman Vander Vos, Bozeman, Mont.
3. Check valve guides. They sometimes work loose.
Read the complete tip →From the archive · Full text
Reader shop tip 4 of 5
Individual tip 4 of 5 from this reader’s published contribution.
Herman Vander Vos, Bozeman, Mont.
4. Don’t use fuel with ethanol in it because it can gum up valves.
Read the complete tip →From the archive · Full text
Reader shop tip 5 of 5
Individual tip 5 of 5 from this reader’s published contribution.
Herman Vander Vos, Bozeman, Mont.
5. Don’t use stale gas because it can also gum up valves.
Read the complete tip →From the archive · Full text
Reader shop tip
Richard Wood, Orting, Wash.
“I put all of my owners manuals in 3-ring notebooks. I cut them up into single sheets so I can put them into plastic document protectors. Keeps everything together and I can look at them with greasy hands.”
Read the complete tip →From the archive · Full text
Reader shop tip
David L. Vandevender Sr., Durbin, W.Virg.
“I use a grease gun adapter with a needle point to grease axle bearings on my farm equipment. I drill a 5/32 or 1/8 in. hole in the center of an axle bearing dust cap and grease with…
Read the complete tip →From the archive · Full text
Reader shop tip
Denny Rawlings, Ehrenberg, Ariz.
“When a 12-volt pulsating fuel pump quits working, they will generally pulse in but not release. I figured out I could install a 12-volt turn signal flasher unit in the positive lead to the pump and it will…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 4
Individual tip 1 of 4 from this reader’s published contribution.
Gary Holland, (ladybug06@wildblue. net)
“Here are some ideas that have helped me: “Buy 1-in. foam pipe wrap and cut it to fit over your windshield wipers. It shields them from heat and cold so they don’t deteriorate. Just take the wraps off…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 4
Individual tip 3 of 4 from this reader’s published contribution.
Gary Holland, (ladybug06@wildblue. net)
“Put a strong magnet on your drill press to hold bits. The bits will become magnetized and shavings will adhere to them. Old speaker magnets work well.
Read the complete tip →From the archive · Full text
Reader shop tip 4 of 4
Individual tip 4 of 4 from this reader’s published contribution.
Gary Holland, (ladybug06@wildblue. net)
“Put another magnet on the drill press to hold the chuck.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Jim Bowser, Saxton, Penn.
“I use anti-skid tape in short strips on both husking rolls on my cornhead to grip stalks better. These strips, which are normally used on stairs and walkways, can be purchased at any hardware store. Once the strips…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Jim Bowser, Saxton, Penn.
Another idea Jim has is to color code his tools by size. For example, he takes all his 7/16th-in. wrenches – open end, sockets, nut drivers, combination wrenches – and spray paints them blue. All 1/2–in. wrenches are…
Read the complete tip →From the archive · Full text
Reader shop tip
Kenneth Jones, Leslie, Ark.
“I had trouble with wheelbarrow tires going flat. I tried tubes but they just kept going flat. So I bought a can of foam insulation and drilled 2 holes in each tire and then filled both of them…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
David Prause, China Spring, Texas
“Because of sprocket wear, the reel drive chains on my 1968 New Holland 469 and 479 9-ft. haybines kept jumping off. Replacing the sprocket and the chains got expensive, so I got a small, flat idler pulley with…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
David Prause, China Spring, Texas
“Used motor oil or 80-weight transmission oil works good to keep roller chains greased. In the field I use a paint brush to apply the grease every 2 or 3 hrs. as the chains are moving. It reduces…
Read the complete tip →From the archive · Full text
Reader shop tip
Glen Goddard, Corinth, Miss.
“We use a golf car at home with six 6-volt batteries connected in series to provide 36 volts. The batteries gave out, and a new set would have cost $1,000 to $1,200. Instead, I went to Wal-Mart and…
Read the complete tip →