Gearhead Café
This company offers a new line of automotive manuals on CD Rom for Ford, GM, and Chrysler cars. The manuals make it easy to print out clean pages to work from so there’s no concern about getting valuable…
Read the complete tip →2077 shop tips and stories · page 17 of 35, newest issues first.
This company offers a new line of automotive manuals on CD Rom for Ford, GM, and Chrysler cars. The manuals make it easy to print out clean pages to work from so there’s no concern about getting valuable…
Read the complete tip →“When using my table saw, instead of pushing the wood being cut with my hand I use a homemade wooden block that’s designed to fit over the saw’s guide bar. The handle off an old crosscut saw is…
Read the complete tip →“We found mildew on the vinyl window seals in a used RV we recently purchased and couldn’t remove it with conventional cleaners. We decided to try some carburetor cleaner sprayed on a rag. It worked like a charm…
Read the complete tip →“I’ve been a mechanic for 45 years and have found that saving bearing races of different sizes has been very useful for installing seals in tight spots. I use them to push the seals into place.”
Read the complete tip →Paul says there’s another neat use for aircraft cable – it can be used to remove hair from drains.
Read the complete tip →“I had some rusted wheel bolts that were stuck. I soaked them with WD-40 but it didn’t help, and I tried heating them with a torch with no luck. I considered trying a cheater bar but was afraid…
Read the complete tip →As gasoline hovers near $4 a gallon, everyone paying at the pump is looking for ways to economize. In the past few years FARM SHOW readers have written us describing how a simple process of “grooving heads” can…
Read the complete story →You can set up a work bench instantly with Handy Bucket Builder (HBB) bucket tops and 2 by 4 studs. The heavy-duty, hard plastic tops fit any standard 5-gal. bucket.
Read the complete story →“Many of us have gas-powered weed whips that only run a short time. About 90 percent of time it’s an easy fix. The manufacturers run the gas line through the side of the plastic gas tank by drilling…
Read the complete tip →“If you get a small tear or rust hole in a gas tank, there’s no need to drain the tank right away. Just rub a bar of soap over the leak and it’ll seal it up temporarily.
Read the complete tip →“To anchor bolts in concrete, drill a hole larger than the bolt you’re using and pour sulphur heated to liquid form in around the bolt.”
Read the complete tip →“The company I work for was going to dispose of a steam cleaner that had been sitting around for years because the pump was worn out. However, the water coil and burner were in good shape. I plumbed…
Read the complete tip →“To carry my outboard motor around for maintenance, I modified a 2-wheel dolly to hold it. After working on the motor, I can simply wheel it back down to the boat.
Read the complete tip →“My grandpa converted a freon tank into this portable air tank. He attached a quick coupler that’s used to fill the tank with air. Then he screwed two male coupler ends together to fill it from a supply…
Read the complete tip →“Two years ago I bought a set of Bad Dog Tools drill bits after seeing them demonstrated at a wood working show. The first one I used broke after just a revolution or two. I checked the other…
Read the complete tip →You get both eye and ear protection in one with these new “combo” safety glasses that are equipped with built-in earplugs on the frames. The built-in earplugs hook onto ear pieces that are part of the eyeglass frame,…
Read the complete story →Jeremy Aaron, an aircraft mechanic from Washington, Penn., was tired of not being able to reach some areas on machines being serviced with the plastic straws that come standard with WD-40 and aerosol products. Getting at remote areas…
Read the complete story →“For retracting the brake cylinder on disc brakes, I use a cheap steering wheel puller. I leave the old brake pad in place and use an impact wrench to turn the bolt. Very handy.”
Read the complete tip →“I had trouble with an old Meyers snowplow freezing up because of moisture in the hydraulic oil. After several mechanics told me ‘don’t do it’, I put anti-freeze in the hydraulic oil. I tried 30 cc’s at first…
Read the complete tip →“A reader in a recent issue wrote about the trouble he had with his Poulan chainsaw. I have a 20-in. Poulan Pro model and one thing I’ve found is that the spark is very weak. Some plugs will…
Read the complete tip →Another thing you should do on this chainsaw is to check the 4 bolts at the bottom that hold the cylinder/crankcase to the body of the saw. Mine fell off and wrecked the gear oiler.
Read the complete tip →Plus, keep checking the muffler bolts for loosening because leaking hot exhaust can eat a hole right into the chain oil tank. If you do those things, it’s a good saw.”
Read the complete tip →“I make cheap penetrating oil using equal parts of fuel oil and transmission fluid. If I have a larger rusted area on a piece of equipment, I soak a rag in the penetrating oil and lay it over…
Read the complete tip →“To remove a rusted bolt that won’t budge, just drill 2 or 3 small holes into the rusted nut and usually it will break loose.
Read the complete tip →“I use automatic transmission oil in my air tools and to rub on my shovels, rakes and other garden tools. Works great because it has rust prevention additives in it. Keeps them looking shiny and new.”
Read the complete tip →“I’ve heard of people squirting WD-40 into small engine carburetors to get the engine started in a hurry. But, WD-40 shouldn’t be used as a starting fluid because it contains silicone, which will coat the cylinder walls and…
Read the complete tip →“For equipment that you frequently run in snow, rain, or mud, use marine grease. Marine grease does a great job of repelling water and creates a barrier for mud. You can put an axle and wheel bearings under…
Read the complete tip →If you want even more light, replace the original bulbs with halogen bulbs.
Read the complete tip →“When replacing bearings in equipment, I place the new bearing in the freezer for 2 hrs. before installing. It usually drops right in without forcing it.”
Read the complete tip →“I’ve found that ‘great stuff’ foam in a can, which is normally used for insulating nooks and crannies, also works great as a substitute for auto body filler. It’s quick, easy to use, and you can cut trim…
Read the complete tip →“I use large dryer hose clamps as ring compressors for large pistons. It’s a quick, simple solution to a job that’s often time-consuming and frustrating.”
Read the complete tip →Eppco’s Black Gold Nitrile Mechanic’s gloves for mechanics are more resistant to chemicals than latex gloves but provide the same “skin-on-bolt” feel. They let you start screws and bolts and pick up small parts as if your hands…
Read the complete story →“To make my own penetrating oil, I mix 2/3 paint thinner with 1/3 light oil. I let whatever part I’m trying to ‘unstuck’ soak overnight. Works well.”
Read the complete tip →“I have arthritis in my hands and I felt there had to be an easier way to shake aerosol paint cans. I hit on the idea of shaking them with a Sawzall. All I do is cover the…
Read the complete tip →“It really does pay dividends to have a subscription to FARM SHOW. Last year I traded 20 lbs. of hamburger for a 1970’s front tine rototiller that supposedly ran great. It did, but only for short periods of…
Read the complete tip →“A friend of mine worked for a tree service for many years. When he has to sharpen a saw with a file, he makes a simple handle out of a corn cob to make it easier to hang…
Read the complete tip →John found a way to make changing high-up light bulbs easy. He started with a length of pvc pipe and the duct-taped a plastic bottle to the end that firmly grips the intended bulb. Lets him change high-up…
Read the complete tip →“Put unsalted hog lard on the threads of anything that you might someday have to take apart. It’ll prevent rust and easily unscrew years into the future.”
Read the complete tip →“To change sickle sections on my hay swather, I put the sickle on a 2 by 6 board with a groove cut in it for the bar to rest in. Makes a sturdy place to remove sections. The…
Read the complete tip →“Carrying a step ladder can be a little awkward. I made it a lot easier by mounting a simple handle on the side of the ladder at the balance point.
Read the complete tip →“I have a 1946 Clark forklift with a worn-out engine. I mounted a 4-cyl. Wisconson engine on back, belted it to the old crankshaft pulley, and removed the pistons from the old engine. Works great.”
Read the complete tip →“The kicker on my father-in-law’s baler was wearing on the main bolt. Essentially the bolt hole became bigger and oblong. To fix it, we drilled the hole out large enough to fit 3 washers in the hole like…
Read the complete tip →“I made my own ‘redneck air ride seat’ by folding up two wheelbarrow inner tubes like hot dog buns and then duct taping them side by side. After adding just a little air, I’m ready to go mow…
Read the complete tip →The DBlaster is a 5-in. long device that uses carbon dioxide cartridges to deliver a blast of air to clean sprayer nozzles, in-line filters and screens. It eliminates the risk of getting chemicals in your mouth by blowing…
Read the complete tip →“In a recent issue someone said his rototiller would act up whenever the fuel tank got down to half full. I think the trouble was really with the gas cap vent, which gets stopped up.
Read the complete tip →“In another report, someone said his chainsaw was cutting sideways because the chain had two teeth on one side, but I don’t think that was the problem. The problem was that one side of the chain was sharper…
Read the complete tip →“I read with interest the reports in your last issue about people having fuel problems with their Deere Gators. I talked to the dealer and he gave me what he called hotter spark plugs. I installed them and…
Read the complete tip →“Recently we had to dig a trench and install a new hydrant in our yard. We were concerned that freezing and thawing could lift the hydrant, causing the plastic pipe that connects to the base of the hydrant…
Read the complete tip →“I always seem to have problems with bent watering wands. I’ve found that by fitting a piece of 1/2-in. I.D. pvc pipe over the aluminum shaft the wand will no longer bend.”
Read the complete tip →When Ed Pacha bought a used Polaris Magnum 425 ATV with a bad engine, he planned to repower it with a V-twin 750. However, when he tore into the Polaris, he realized he couldn’t make the Polaris belt…
Read the complete story →“I use 3/4-in. thick, 4 by 8-ft. sheets of oak veneer plywood to make wall units and entertainment centers. To cut straight without splintering, I came up with the idea of laying the plywood sheets on top of…
Read the complete tip →“I’ve noticed reports from several FARM SHOW readers who’ve had trouble with gas getting into the crankcase on Deere Gators. That gas washes oil off the cylinder walls, shortening the life of the engine if not destroying it.…
Read the complete tip →“Here’s a way to keep a spray nozzle clear after doing a small touch-up paint job and there’s still paint in the can. In order to keep paint from drying in the nozzle and plugging it up, first…
Read the complete tip →“I’d like to offer help to Wayne Harley in Penn., who had a problem with gas leaking into the crankcase on his 2007 Deere 6 by 4 Gator equipped with a Kawasaki engine (Vol. 34, No. 2). I…
Read the complete tip →“Here’s an idea that saves time when changing sickle sections. I modified a vice grips to knock out the sickle section rivets and bolts. I just brazed a half nut and a #50 chain rivet to the side…
Read the complete tip →“I cut off 6-in. long pieces of old high pressure air hose and use them as handle cushions on 5-gal. buckets.”
Read the complete tip →“I needed to make wheels for a school project and I needed them right away. I came up with a quick and easy way to make them out of wood scraps.
Read the complete tip →“I use hex nuts and bolts to make thread cleaners to clear rust and dirt buildup out of threads on any piece of equipment.
Read the complete tip →“To make a thread cleaner out of a bolt, I cut an ‘X’ in the end of the threaded end of a bolt and use a file to taper the threads at that end of the bolt. Helps…
Read the complete tip →“I do the same thing to make a spark plug hole thread cleaner. Just cut off the electrode on a spark plug and cut an ‘X’ in the threaded end, file it down a bit, and insert into…
Read the complete tip →