From the archive · Full text
Feature story
Featured source: Joey Waldner
“Our new lift for high-clearance sprayers works great for changing tires and doing other maintenance work. It’s the safest jack system on the market for sprayers,” says Dan Waldner, RockPort Welding, Magrath, Alta. The sprayer lift is designed…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Paul Citoli
Paul Citoli likes to think of RubberizeItΤΜ as duct tape in a can. There seems to be no end to the uses customers come up with for the coating that repairs leaks, prevents rotting and corrosion, and adheres…
Read the complete story →From the archive · Full text
Feature story
Featured source: Leonard Wulf
Leonard Wulf’s 1973 Model 371 Bobcat looks like new and runs better than new since he converted it to a 20 hp Honda V-Twin engine. The old 13 hp Kohler engine was underpowered to begin with and about…
Read the complete story →From the archive · Full text
Reader shop tip
Allen Dilg, Gurnee, Ill. (ardilg@yahoo)
“We do a lot of tractor restorations and came up with an easy way to get rid of crud in a vehicle’s fuel tank. Open the drain on the carburetor, and the fuel should run out in a…
Read the complete tip →From the archive · Full text
Reader shop tip
Clinton Keeney, Creighton, Mo.
“I couldn’t find wheel weights for my Ford 4000 tractor, and I didn’t want to fill the tires with fluid. Instead, I found some bar bell weights that were the right size and welded an 18-in. length of…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Mike Kellett, Sublette, Kan.
“When the rechargeable batteries on a power tool go bad, I take the tool apart and solder a coiled cord to the contacts inside the handle. I have a one-way plug in my pickup bed that’s connected to…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Mike Kellett, Sublette, Kan.
“I use my leaf blower constantly in the shop to dry spills, sweep in hard-to-reach places, clean out combines and tractor cabs, blow dirt off clothing, dry paint and even to discourage stray cats and other varmints that…
Read the complete tip →From the archive · Full text
Reader shop tip
Robert Boddy, Bloomingfield, N.Y.
“I mounted an electric generator to the base of a push lawn mower. It makes moving the generator from place to place much easier. Real handy.”
Read the complete tip →From the archive · Full text
Feature story
Featured source: Ken Schulte
“We don’t recommend the Tread Doctor for tractors or other big equipment tires, but it works great on motorcycles, ATV’s, cars and light duty truck tires,” says Kevin Schulte, Hardline Products. Over time, aggressive tire treads round off,…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
MDI Products, 36 Hovey Rd., Monson, Mass. 01057 (ph 866 213-0772; www. mo-deck.com)
Grass has a tougher time building up under mower decks treated with Mo-Deck aerosol undercoat, says the company. It keeps wet grass from sticking to the deck and greatly reduces the need to do any power washing or…
Read the complete tip →From the archive · Full text
Reader shop tip
Richard Duane, 311 Congressional Drive, Stevensville, Md. 21666 (ph 410 643-2899)
If you’ve been online looking for older Deere parts lately, you know that often the parts you need are no longer available. One such part is the water pump rear cover plate on Deere 420, 430 and 440…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Richard A. Rice
“Several years ago I acquired some old Purolator PER-3 spin-on oil filters from a service station that was closing. I had to make an adapter so I could use them on my Farmall A tractor,” says Richard Rice,…
Read the complete story →From the archive · Full text
Feature story
Featured source: George Muth
George Muth keeps a clean engine, thanks in part to his Blow-by Reservoir. Without it, blow-by oil collects under engines, drips onto roadways and collects at intersections.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Princeton Flighting Corp.
Minnesota farmer Dennis Skaro says, “When metal augers have excessive wear, they need to be repaired or replaced or they’ll damage grain and cost you a bunch of money.” That’s why Skaro likes Princeton Flighting, an Illinois company…
Read the complete story →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Dan Hyer, Lancaster, Wis.
“A bearing went out on a tractor front hub, chewing up the area that holds the seal. I couldn’t find a new part for that and I needed the tractor right away, so I installed new bearings and…
Read the complete tip →From the archive · Full text
Reader shop tip
Danny Holder, Kerneysville, N.C.
“My Ford 3930 had an oil filter under the left footrest that was exposed so it could get damaged. I welded a shield under the filter and also made a low step on the shield to make it…
Read the complete tip →From the archive · Full text
Reader shop tip
Dean Pingel, Hilbert, Wis.
“Here’s how I built an electric starter for my Farmall F-12 tractor. The ring gear is from a Ford Taurus and the starter is a Ford marine starter, which I used because it turns in the same direction…
Read the complete tip →From the archive · Full text
Reader shop tip
Their Sloppy Shifter Fix stops your IH tractor from jumping out of gear or shifting into the wrong gear. It’s for use on IH 300, 350, 400, 450, 460, 560, 600, 650 and 660 tractors; Models H, SH,…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
O.E.M. Tractor Parts, Chenoa, Ill. (ph 800 283-2122; www.oemtractorparts. com)
This company’s Tractor Tool Tray is designed for IH tractor models H through 1568. The tray snaps onto the tractor rail to keep tools at your fingertips. It measures 22 in. long by 10 in. wide and comes…
Read the complete tip →From the archive · Full text
Reader shop tip
Simon Gordon, Irvington, Ky.
“The gas tank on my 1963 Massey Ferguson tractor rusted out and I could not find a replacement. So I turned a 30-gal. propane tank into a gas tank and it has worked out well for the last…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Carlos Rosario
If Specialty Carburetors doesn’t have the carburetor you need, they can rebuild the one you have. The company works with classic carburetors from the 1930’s to modern units in auto, truck, tractor, industrial and marine engines. They also…
Read the complete story →From the archive · Full text
Reader shop tip
Fifth Avenue Antique Auto Parts, 415 Court St., Clay Center, Kan. 67432 ph 785 632-3450; fifthaveinternetgarage.com
Their “remote battery stud” allows multiple electrical accessories to be powered directly from your battery. Works great when adding GPS monitors and related accessories in tractor cabs. The studs can be mounted anywhere and provide power direct from…
Read the complete tip →From the archive · Full text
Reader shop tip
Todd Hutter, Freeland, Mich.
“Any grass that stuck to the deck on my riding mower would cause rust and scale to build up. So when I bought a new Cub Cadet lawn tractor equipped with a 50-in. deck, the first thing I…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Erik Schroeter
Arnold “Fred” Schroeter opened his diesel injection repair business in Sioux City, Iowa, almost 50 years ago. Today that business has locations in Omaha, Neb. and Estherville, Iowa, operated by Fred’s daughter Amy and son, Erik. A staff…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Haim Zeevi
Haim Zeevi offers a service to put the finishing touch on the tractor you have just restored. He restores tachometers. Customers can choose to keep the face as is, or he’ll make it look brand new with a…
Read the complete story →From the archive · Full text
Feature story
Featured source: Joe Victory
“Anyone who has ever owned a Case 1190 tractor and had the power steering go out knows that it’s almost impossible to find a replacement pump,” says Joe Victory, Culleoka, Tenn.
Read the complete story →From the archive · Full text
Feature story
Featured source: John Blackwell
“I sat in my shop thinking one day that I needed a hoist for my riding mowers and ATV’s. I didn’t want to spend a lot of money, so I built one that makes use of an ordinary…
Read the complete story →From the archive · Full text
Feature story
Featured source: Ed Welters
Ed Welters of Welters Farm Supply, Verona, Mo., recently contacted FARM SHOW about a couple of modifications he makes to older White diesel tractors to improve fuel economy. Welters is a White farm equipment dealer who services equipment…
Read the complete story →From the archive · Full text
Reader shop tip
Chuck Norman, Pine River, Minn.
“When installing a starter on a tractor, I needed a special wrench. Rather than try to buy one, I used an acetylene torch to bend a 9/16 box end wrench to fit the situation. Worked great.”
Read the complete tip →From the archive · Full text
Reader shop tip
Dave VanNorman, 209 Jacobs Rd., Wind Ridge, Penn. 15380 (ph 724 428- 3401; maryanddavid209@windstream. net )
“I machine adaptors from 6061 aluminum to adapt 3⁄4 and 1-in. return lines from post pounders to the tractor (returns such as fill plug openings). Post pounders return a lot of fluid each time the pounder is activated.…
Read the complete tip →From the archive · Full text
Reader shop tip
Jeff Heiser, Vesper, Wis.
“I had to install hard plastic seals on the 3-pt. arms of a Deere 2030 tractor at the lower end of the transmission case. The seals were hard to handle so I put some oil in a small…
Read the complete tip →From the archive · Full text
Reader shop tip
Ken Skow, Lewiston, Mich.
“Finding good used rims for older tractors can be quite a challenge. When I needed a set for the front of my little Allis tractor I couldn’t see paying $70 or more for new ones. I found some…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Tom Wessman, Albert City, Iowa
“If your combine bounces down the road after the tires get a flat spot from sitting overnight, leave the header down a little. It’ll help smooth out the ride.
Read the complete tip →From the archive · Full text
Feature story
Featured source: Chad Travis
“I recently came up with this homemade repair tool that makes it easier to remove the blade bar from the gearbox on a bush hog mower,” says Chad Travis, Drasco, Ark.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Dan Steiner
You can dress up an old Farmall with these shiny new “restoration quality” mufflers, says Steiner Tractor Parts, Inc. Mufflers are available for Farmall models made from 1939 to 1963 and are available in 2 different styles: aluminized…
Read the complete story →From the archive · Full text
Feature story
Featured source: Jay Russell
Abilene Machine has been helping convert Deere 3010, 3020, 4010 and 4020 diesel tractors from 24-volt to 12-volt for years. They recently introduced a new 24-volt to 12-volt conversion kit that includes a gear reduction starter developed especially…
Read the complete story →From the archive · Full text
Feature story
Featured source: Tim Steele
Tim Steele found a good sideline business cleaning engines and other metal parts with his bead blaster. He uses #80 glass beads to remove rust, oxidation and corrosion without damaging the metal.
Read the complete story →From the archive · Full text
Feature story
Featured source: August Stark
“I’ve probably got the only one-ton dump truck with an air hose hanging out of the grill and an air compressor mounted under the hood,” says retired but still active handyman August Stark of Merrill, Wis. Stark built…
Read the complete story →From the archive · Full text
Reader shop tip
“Mice chewed so many holes in my canvas grain aeration duct that I discarded it and replaced it with a tractor inner tube. The 20.8/38 tube fit over the fan’s 9 by 14-in. square outlet with a little…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Justin Kelzer
The 1/4 hp, 4-speed drill press Justin Kelzer built consists of an antique Champion #97 post drill with a pulley drive attached. Kelzer added a motor and transmission and mounted everything to a wood frame.
Read the complete story →From the archive · Full text
Feature story
Featured source: Vince Osburn
Vince Osburn’s homemade grinding tool lets him get inside the differential housing on a Deere 2020 tractor to guide a grinding wheel to resurface the brake contact area. Adding a second plate and spacers make the tool perfect…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Andrew Sewell, Richmond, England
“I spotted this idea on a farm recently. The owner of this combine writes the belt size and parts number right next to each belt on the machine with a permanent marker. Simple, but he says it saves…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
David McRae, Whitehall, Wis.
“I wanted a way to extend the use of hard-to-find tractor tires once they developed breaks in the sidewall. So I made boot inserts out of 10-in. smooth triple-ply belting. I bevel the edge of the cut. Then…
Read the complete tip →From the archive · Full text
Reader shop tip
Ernest See, Baker, W. Va.
“We needed to move the wheels out on our Deere 4020 tractor. We tried using heat and an impact wrench, but nothing worked. Then our dealer suggested slipping a piece of pipe over the axle and hammering on…
Read the complete tip →From the archive · Full text
Reader shop tip
Ronnye Tattershall, Independence, Kan.
“My Ford tractor clutch locked up. I poured Coca Cola on it and it freed right up.”
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Arthur Kidder doesn’t worry about overloading his tractor’s front-mounted forklift anymore. His bolster repair is heavy enough to carry nearly any load.
Read the complete story →From the archive · Full text
Feature story
Featured source: Greg Stephen
“If you’re looking for rare and hard-to-find tractor parts, I probably have them, know about them, or can tell you where to find them,” says Greg Stephen, who has made antique and unusual parts his business for the…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Marco Romani says his power brake bleeder kit saves money on brake jobs, and marriages, too!
Read the complete story →From the archive · Full text
Reader shop tip
Art Spearman, Independence, La.
“The inside clip that holds the pto lever in place on my 1961 Deere 1010 tractor came off. Rather than go through the trouble of breaking the tractor in half to replace the clip, I simply bolted a…
Read the complete tip →From the archive · Full text
Reader shop tip
Harold Fratzke, Cottonwood, Minn.
“Putting on dual wheels doesn’t have to be a difficult job. All I do is jack up the tractor. I made 2 stud bolts that screw into the casting. I roll the dual up to the casting and…
Read the complete tip →From the archive · Full text
Reader shop tip
Kevin Holland, Sandy, Vt.
“Here’s an idea I use whenever I want to work on the hydraulic pump on my 1939 Ford 9N tractor, or change out the pto shaft. I park the tractor on a slight hump in my yard so…
Read the complete tip →From the archive · Full text
Reader shop tip
Lonnie Rixen, Sabula, Iowa
“The shifting cables on Deere combines and choppers can become gummy, making them hard to shift. To solve the problem, I remove the cable and put an electric drill on the end to turn the center wire as…
Read the complete tip →From the archive · Full text
Reader shop tip
Stephan Rodamaker, Janesville, Iowa
“I own Deere 2505 and 2210 tractors. By cutting an access hole in the floor and cowel I can lubricate the U-joints and yoke. Otherwise, it’s a costly expense.”
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Steve Carey, Boulder, Mont.
“A good time-saving idea is mounting an air hose near the shop doors. Makes filling up tractor and truck tires easier. Don’t have to mess with tangled-up hoses outside.”
Read the complete tip →From the archive · Full text
Reader shop tip
Wesley Walker, Cooper, Texas
“I had a problem with the gearshift lever on my IH 86 Series tractor. The lever is made out of common bar stock and it wears around the vertical transmission shaft, which makes shifting gears difficult. To solve…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Hank Psolka of Dallas, Penn., recently sent FARM SHOW photos of how he put an oil leak on his tractor to good use.
Read the complete story →From the archive · Full text
Feature story
Featured source:
“If you’ve got an older Deere tractor that you want to hook up to a manure spreader or a mower or some other tool with a 20 spline pto shaft, this insert shaft makes it real easy,” says…
Read the complete story →From the archive · Full text
Feature story
Featured source:
If you have old brakes and clutches that need relining, Tim Doran of All Frictions Co. can help. His company has lined all sizes of friction clutches and brake drums up to 56-in. dia. – big enough to…
Read the complete story →