Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Larry Goodman, Ionia, Mich.
Larry Goodman had no good way to see the forks attached to the bucket of his backhoe. He purchased a wireless backup camera with a strong magnetic base and placed it inside the bucket, and placed the monitor…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Larry Goodman, Ionia, Mich.
Larry Goodman, Ionia, Mich.: “I purchased a trailer to haul my mower, but the 4-ft. ramp was on too much of an angle to load. The mower deck was too low, so I installed a bracket on the…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Roy Bertalotto, Dartmouth, Mass.
Roy Bertalotto’s gantry crane makes pulling a camper off a truck or lifting a tractor to work on easy. The crane is 12 ft. high, 11 ft. wide and 44 in. deep. Building it with pallet racking was…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: John Humeniuk, Baudette, Minn.
John Humeniuk gets a ton of use out of his mobile hydraulic pump. It powers his log splitter, grain conveyor, sawmill, dump trailer and more. There’s no need to pull up a tractor with hydraulics when he can…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Gary Swensen, Yankton, S.D.
Gary Swensen, Yankton, S.D.: “I shared in modifying a one-ton pickup box and rear frame into a field trailer. I’d mounted an 80-gal. propane tank to the tongue to serve as a high-capacity air supply. Recently, I made…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Oscar Scott, Perryton, Texas
Unscrew a hydraulic oil filter, and if you just lose a few gallons of oil, you’re lucky. Oscar Scott wasn’t, so he figured out how to eliminate oil loss and the mess that often comes with it. His…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: John Else, Cedar Falls, Iowa
Laforge LLC began its product line of after-market front-mounted hitches and PTO drives due to a need by some of the larger tractor manufacturers decades ago.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Skid Steer Solutions, Bellingham, Wash.
Connecting hydraulic couplers when line pressure has built up can be nearly impossible. The QC Mate Quick Coupler Hand Clamp from XBoom solves the problem quickly and safely.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Curtis Burcham, Guntown, Miss.
“This storage box from Amazon is a great addition to my tractor. Excellent purchase that allows me to carry tools and other supplies away from the shop.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Norman Sieting, Rapid City, Mich.
“I like to take a trailer to toss wood into when I head to the woods with my splitter. That has meant making two trips with my ATV or pushing the splitter ahead of the ATV while towing…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Norman Sieting, Rapid City, Mich.
“The step-down mount has come in handy for other uses as well. I have dirt and snow blades that mount on receiver hitches on the front and back of my ATV. I remove the ball mount and put…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Warren Zimmerman, Wheeling, Mo.
“Case IH Maxxum tractors have a foam seal under the cab roof that deteriorates and drastically reduces A/C cooling capability. No longer OEM, I used Emseal sealing foam to repair them.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Warren Zimmerman, Wheeling, Mo.
“A 630 Bobcat skid steer hydrostat pump had the input shaft seal retaining snap ring groove destroyed. Rather than buying a new housing or pump, I ground down the housing flush with the mounting flange and had a…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Warren Zimmerman, Wheeling, Mo.
“I’ve added small flat free wheels to each front corner of my 7-ft. Brush Hog. It now doesn’t gouge or cut in like it used to.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Kevin Schrock, Millersburg, Ohio
Bunker Hill Cables of Holmes County, Ohio, sells individual cables directly to customers. These include affordably-priced replacements for name-brand equipment, duplicates of obsolete cables, and custom work for customer-specific applications.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Steve Vargo, Valley Grove, W.Va.
At nearly 80, Steve Vargo had no interest in having to jump off his IH 706, so he engineered an emergency stop. He did so after backing it out of his shed and finding himself without steering or…
Read the complete story →From the archive · Full text
Reader shop tip
David J. Byler, Brockway, Penn.
“For most lawn tractors with a 2-cyl. engine, the engine needs to be completely removed from the tractor to replace a faulty ignition coil. To save the customer labor costs, after consultation and permission, I cut out a…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Doug Barlow, Trenton, Fla.
Replacement grills for older tractors are hard to find, so Doug Barlow made his own. All it took was a good eye, steady hands, angle iron, cattle panel and expanded sheet metal.
Read the complete story →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Allen Pederson, Nashua, Iowa
“I found a single field cultivator tooth with a spring on the highway. I bolted it to a tractor bucket to dig electric cable in.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Jeff Hootman, Jeromesville, Ohio
“In 2015, I purchased a Cub Cadet three-stage snowblower. It seems to have been designed for someone 5 ft. 6 in. I’m 6 ft. tall. So, I built a subframe for my Wheel Horse garden tractors (1979 C-81).…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Jeff Hootman, Jeromesville, Ohio
“I used 16-ft. stock panels from Tractor Supply and Harbor Freight tires to make a place to park my garden tractors and lawn mower.”
Read the complete tip →From the archive · Full text
Reader shop tip
Joe Hanson, Aberdeen, S.D.
“A welding vice grip clamped onto the side of a mower deck works great for holding the blade when tightening or loosening.”
Read the complete tip →From the archive · Full text
Reader shop tip
Roger Hathcoat, Nowata, Okla.
“I had a problem with my older Massey Ferguson tractor dying after running for only half an hour. I flushed the fuel tank, installed new coils, and tried other fixes. Nothing worked.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Warren Zimmerman, Wheeling, Mo.
“Case IH Maxxum tractors have a foam seal under the cab roof that deteriorates and drastically reduces A/C cooling capability. No longer OEM, I used Emseal sealing foam to repair them.
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Wayne Hopper and Bill Garniss, Brussels, Ontario, Canada
In April 2023, Brussels, Ontario, farmer Wayne Hopper bought a used Deere 8650 4-WD tractor from a farmer near Aylmer, Ontario, thinking he’d gotten a good deal. However, as he drove it to a dealer in Walton, Ontario,…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Glenn Dawson, McConnelsville, Ohio
“I had trouble with the front hydraulic cylinder on my Kubota tractor. I replaced it with a 12-volt winch. It works great.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Steve Faber, Tiffin, Ohio
“I had some implement tires with really slow leaks that I couldn’t find, even with brushing soapy water on them. I remembered seeing tanks for finding leaks at tire dealers, so I cut off a chemical tote to…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Norm Sieting, Rapid City, Mich.
“I have a CountyLine wood splitter from Tractor Supply. It works fine except for two problems.
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Matt Willard
The Mule Mobile Workshop is a professional-grade work cart with a fan, light, and power solution. It transforms any space into a workshop.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Charles Bowen, Valley City, N.D.
Charles Bowen’s 30-year-old Mustang skid steer still works great, but it won’t work with the broad array of Bobcat-style attachments. Mustang quick attachments have a single locking pin in the center instead of a locking lever on each…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Mike Kloster, Litchfield, Ill.
The EPFC-1 pallet fork clamp from Worksaver attaches easily and requires no auxiliary hydraulic valve. Designed for use with compact and subcompact tractors, it uses an electric actuator with an 8-in. stroke to operate the clamp.
Read the complete story →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Fritz Groszkruger, Dumont, Iowa
“The two halves of the loader control handle on 5105M cost $876 to replace. I’m trying to repair it with JB Weld. I imagine these parts prices are to subsidize their electric tractors. The world has gone nuts.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Steve Ragan, Eustace, Texas
“This is the easiest but most useful modification I’ve ever put on a tractor. I always drink something when working with my tractor and never have a place to put my cup. A 3-in. flexible PVC coupler solves…
Read the complete tip →From the archive · Full text
Reader shop tip
Warren Hartl, Yoakum, Texas
“It was hard to change the blades on my zero-turn mower or clean under the deck. I welded a trailer jack to the front. Now I can jack it up to 30 in. off the ground to clean…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Brent Uffelman, Waco, Neb.
When Brent Uffelman needed to move his small farm equipment and trailers in and out of his sheds, he created a small device he could use with his propane-powered forklift to simplify the task.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Andy Burish, Cumberland, Wis.
The Earthquake® OutriggerTM Auger Torque Reducer works to turn two-man auger jobs into one-man jobs.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: E.J. Swihart
When a local farmer came to E.J. Swihart with a problem, the two devised a solution. The problem was being unable to fine-tune the closing wheel downforce on a Deere planter.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Gary Meeks, Verona, Va.
Gary Meeks suffered the granddaddy of mower blade messes while mowing behind his barn with his zero-turn mower.
Read the complete story →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Bill Kendall, Maryville, Tenn.
“John Deere asks $245 per tie rod end for my 3032E tractor. I found replacement ends by going to Auto Zone. It had a box of N.O.S. ends that weren’t marked. It took a little time, but with…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 4
Individual tip 1 of 4 from this reader’s published contribution.
Paul Scholand, Ypsilanti, Mich.
“I have a tractor with a front-end loader. The battery is just inside the front grill. If the loader isn’t in the raised position, it’s hard to connect a charger or jump pack to the side battery terminals…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 4
Individual tip 2 of 4 from this reader’s published contribution.
Paul Scholand, Ypsilanti, Mich.
“A lawn mower deck can break at the side discharge opening. I’ve used a ratchet strap to pull the edges of the break together and use flat steel and self-tapper screws to hold it together. It’s quick and…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Douglas Welding and Machine, Salina, Kan.
Douglas Welding and Machine (DWM) makes a post/tree puller like no other. They make a lot of unique skid steer attachments, 43 to be exact. In some cases, attachments are ones DWM owners Colby and his dad Leroy…
Read the complete story →From the archive · Full text
Reader shop tip
Grant, Ilparpa, Australia
“When using my Cub Cadet ST 100 22-in. wheeled string trimmer, the cord breaks off regularly. Carrying enough extra cord was a problem. So, I cut a 500mm length of 50mm diameter Poly Pipe, capped the bottom end,…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
John Mathis, Smithland, Ky.
“John Deere’s disc mower has a bearing problem. The main drive bearings are enclosed in a housing. When the seals on these bearings fail and the grease dries up, the bearings fail completely. I drilled, tapped, and installed…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Redekop Manufacturing, Saskatoon, Sask., Canada
The Redekop KAS Intake Pre-Cleaner works to extend the life of air filters in farming and construction equipment by cleaning the air before it enters the engine. As a result, you’ll get easier filter maintenance over the long…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
David Simpler, Elkton, Md.
“I use a cam-lock load binder to tension the drive belt on my rotary mower.
Read the complete tip →From the archive · Full text
Reader shop tip
James Neppl, Preston, Minn.
“When my IH 1460 combine went down between a field and home, I used two hose clamps and a piece of inner tube on the hydraulic suction line to get it back home.”
Read the complete tip →From the archive · Full text
Reader shop tip
Nigel Thornborrow, Yorkshire, U.K.
Nigel mounted a bicycle water bottle holder to the cup holder in his tractor cab so he could have both hot and cold beverages handy at the same time. We found Nigel’s idea in Profi magazine U.K. (www.profi…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Tom Mattiuz, Saint Marys, Penn.
“I bought a Deere X390 lawn tractor with a mower and 44-in. snowblower. The blower belt is a bear to install. The instructions state that once the blower is mounted, you raise it to the uppermost level to…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Ben Garmier
Bio-Ultimax 1000 is a biosynthetic oil that lasts longer, performs better, and handles cold weather better than standard hydraulic fluids. The biodegradable product from Renewable Lubricants works well in high and low-pressure hydraulic systems. It directly replaces mineral…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Simon Oyler, Delphi, Indiana
Indiana crop and livestock farmer Simon Oyler has a simple way to clean out trash, dirt, and other materials from inside the pan of his and his dad’s L220 and L230 skid steer loaders.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Dawson Tire & Wheel, Gothenburg, Neb.
Tires aren’t cheap, so it pays to know all you can about them. Tire sidewalls are loaded with information if you know how to interpret it. When Dawson Tire & Wheel introduced their TreadSure App (Vol. 47, No.…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Dale McLaen, Rutland, N.D.
You can never have too much light when moving snow with a skid steer at night, but too bright a light can blind others working around you. Dale McLaen solved the problem by attaching LED lights to the…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Dale McLaen, Rutland, N.D.
If plugged or overflowing carburetors are a problem in your seldom-used older tractors, Dale McLaen has some suggestions. Over his 27 years of repairing all types of farm engines in his on-farm shop, he has cleaned and used…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Schuyler Rubber Company, Woodinville, Wash.
Cutting edges for skid steer buckets are only one of a wide variety of products Schuyler Rubber Company makes out of old bus and truck tires. The company has been recycling tires and other rubber products for more…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Dawson Tire and Wheel, Gothenburg, Neb.
Dawson Tire and Wheel is taking the guesswork out of estimating tread life on ag equipment tires and tracks with their TreadSure app. Measure the tread, and the app will tell you what percent is left by comparing…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Ballard, Inc., Ankeny, Iowa
The EZ Pro Lift from Ballard is a versatile 2-wheel jack for everything from riding mowers and garden tractors to ATVs, UTVs, and golf carts. It has five lock-in positions for machine widths of 36 to 50 in.…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Curtis Hiebert, Sperling, Manitoba, Canada
Mount the Lend-A-Hand attachment on a tractor fender and keep hydraulic hoses and electrical lines up and away from hitches. The hanging arm articulates with the hitch as the tractor turns.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Roscoe Lynn, Bryceville, Fla.
Three years ago, Roscoe Lynn took his 15-year-old Kubota to a dealer to get a bucket put on the front. While there, he saw a tractor similar to his that was waiting for repair because it had ripped…
Read the complete story →