Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW

Equipment

1669 shop tips and stories · page 21 of 28, newest issues first.

From the archive · Full text
Reader shop tip

Donald Waehl

Donald Waehl, Morrison, Ill. (ph 815 772-3765)

“I have a problem I can’t solve on my 1958 720 Deere 2-cyl. tractor. I put an alternator on it last winter and it worked fine until it warmed up this summer. Then I couldn’t keep points or…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Edward B. Edelen

Individual tip 1 of 2 from this reader’s published contribution.
Edward B. Edelen, Jr., Bryantown, Md.

“The fuel injection pump on my Deere 3010 failed. But I was able to get it working again by rigging up a system to relieve pressure on the fuel return line from the injector. Using two “T” fittings,…

Read the complete tip →
From the archive · Full text
Reader shop tip

Farmchains.com

Farmchains.com, 105 S. Peoria Ave., Dixon, Ill. 61021 (ph 800 648-5429; fax 815 288-6790; website: www.farmchains.com)

This new website offers a wide variety of tractor, header, roller chains, steel chains, and other miscellaneous agricultural attachment accessories. The costs are often much lower and they say they offer the widest selection on the web. If…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 4

Elmer Pinkerton

Individual tip 1 of 4 from this reader’s published contribution.
Elmer Pinkerton, Elmwood, Neb.

“There are several suggestions around on how to remove the nut that holds the blade on push lawn mowers. Forget them all. An air impact wrench will bring that nut off in seconds without anything holding the blade.…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Steve Spiering

Individual tip 2 of 2 from this reader’s published contribution.
Steve Spiering, 48594 Hwy. 158, Milbank, S. Dak. 57252 (ph 320 568-2246)

“Our 7-in. dia., 55-ft. long, pto-driven grain auger wasn’t big enough to meet our needs any more, so I converted it to an electric-op-erated model to boost capacity. A 5 hp electric motor mounts on two lengths of…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 3

Vic Smith

Individual tip 1 of 3 from this reader’s published contribution.
Vic Smith, Parkville, Mo.

“While restoring my great grandfather’s old 2-row Ford planter, I found that some springs were old and rusted. To solve the problem I bought surplus spring kits at Tractor Supply. I treated some of the old and rusted…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 3

Bill Reeks

Individual tip 1 of 3 from this reader’s published contribution.
Bill Reeks, Cromwell, Ky.

“Lawn tractors usually get used only for mowing and maybe for towing a small cart or trailer. To make my new Sears Craftsman 17 1/2 hp riding mower more versatile, I removed the hood and installed a bumper…

Read the complete tip →
From the archive · Full text
Reader shop tip

Bob Batteen

Bob Batteen, Box 401, Urbana, Iowa 52345

“In a recent issue of FARM SHOW someone complained that the disc brakes on their Super “M” and Super “MTA” tractors don’t last very long. Maybe this idea will help. Whenever you’re replacing the brakes on these tractors,…

Read the complete tip →
From the archive · Full text
Reader shop tip

Dave Cook

Dave Cook, 28800 Cook Road, Washburn, Wis. 54891 (ph 715 373-2092)

Deere’s popular 420 garden tractor, made from 1954 to 1961, could originally be fitted with an optional foot throttle assembly. The company doesn’t make the foot throttle kit any more, so Dave Cook, Washburn, Wis., decided to produce…

Read the complete tip →
From the archive · Full text
Reader shop tip

Keith Snyder

Keith Snyder, 2435 Route 973 East, Cogan Station, Penn. 17728 ph 570 494- 2627

“My homemade tractor stand mounts on wheels and uses a pair of hand-operated jacks to split the tractor, allowing installation of a new clutch or torque amplifier or removal of the engine. The stand attaches in four places,…

Read the complete tip →
From the archive · Full text
Reader shop tip

Woods Equipment

Woods Equipment, Oregon, Ill. Ph 815 732-9395; website: www.woodsonline.com

This company introduces Vintage Iron, a new line of Tisco repair and restoration parts for tractors built from 1939 to 1969. Parts are available for a wide range of brands including Allis Chalmers, Case, Cockshutt, Case/David Brown, Ford,…

Read the complete tip →
From the archive · Full text
Reader shop tip

Kerry Jahns

Kerry Jahns, Sand Lake, Mich.

“My Massey tractors sometimes need a boost to start. The starter is out in the open so rather than pull off the grill or hood, I connect the booster cable direct to the starter solenoid. Just be careful…

Read the complete tip →
From the archive · Full text
Reader shop tip

Calyx Manifold Dressing

Calyx Manifold Dressing, Box 53277, Cincinnati, Ohio 45253 (ph 800 313-5671 or 513 923-1154; fax 513 923-1154; www.calyxmanifold.com)

This company offers a paste-type dressing that lets you keep the exhaust manifold on any vehicle looking great at all times. You don’t have to remove the manifold to use it. The paste applies with a flannel cloth…

Read the complete tip →
From the archive · Full text
Reader shop tip

Jesse Larson

Jesse Larson, 21880 431 Ave., DeSmet, S. Dak. 57231 (ph 605 854-3108)

Jesse’s a diesel technology student at Lake Area Technical Institute, Watertown, S. Dak. He and Steve Peters, a diesel instructor, came up with an inexpensive way to recharge 90-amp Nippondenso alternators commonly found on Deere tractors.

Read the complete tip →
From the archive · Full text
Reader shop tip

John McElroy

John McElroy, McElroy Enterprises, Inc., 411 First Ave. S., Ft. Dodge, Iowa 50501 (ph 800 397-3669)

“Your readers may be interested in our Kreem fuel tank liner. It’s an epoxy-type product that’s designed to prevent rust and corrosion and stop leaks in fuel tanks. It works great on old tractors and cars with tanks…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Roy Klindt

Individual tip 2 of 2 from this reader’s published contribution.
Roy Klindt, Crane Valley, Sask.

“The pto-operated hydraulic pump on my New Holland haybine is quite heavy and tended to sag on the tractor’s pto shaft. The resulting vibration caused the hydraulic hoses to rub against the haybine frame. I was afraid the…

Read the complete tip →
From the archive · Full text
Reader shop tip 3 of 3

Dennis Albright

Individual tip 3 of 3 from this reader’s published contribution.
Dennis Albright, Springfield, S.Dak.

“Here’s another idea I’ve used for years on crawler tractors, from the smallest to the biggest. When bushing or tapered roller bearing-type tracks start to leak oil, I fill them with regular grease gun grease. They’ll go a…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Karey Waldrop

Individual tip 2 of 2 from this reader’s published contribution.
Karey Waldrop, Walterboro, S.C.

“I also converted an old gas grill that didn’t work any more into a portable parts washer, by replacing the grill with a 3-gal. electric-operated parts washer. I use the grill’s folding front and end sections to hold…

Read the complete tip →
From the archive · Full text
Reader shop tip

Sam McConnell

Sam McConnell, Bogata, Texas

“I’ve got a question for tractor manufacturers. How come auto manufacturers can make fuel gauges that work for the life of the car but tractor manufacturers can’t seem to make one that works for more than a couple…

Read the complete tip →