From the archive · Full text
Feature story
Featured source: Reid Allaway
“When the blunted end of a cable came loose on one of our tractors so the control handle didn’t work, I couldn’t find a replacement part, so I decided to fix it myself,” says handyman Reid Allaway of…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
By By Mark Newhall, Editor
Featured source: Dale Colvert
I got a call the other day from Dale Colvert, an electronics wizard who was featured in our last issue with an after-market ignition module for older Tecumseh engines. He wanted to tell me about another product he…
Read the complete story →From the archive · Full text
Feature story
Featured source: Bob Payne
“I bought a wall-mount, non-vent propane residential heater cheap at a flea market and strapped it onto my 2-wheeler. It’s nice and quiet and can be easily moved anywhere in the shop I need heat,” says Bob Payne,…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Tom McNamara
If you’re looking for a used lawn mower or parts, Almost Heaven Lawn Mower Grave Yard in Bluffton, Ind., is a great place to start. It’s a “pick-apart yard,” says Tom McNamara, who helps his son, Scott, run…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Dan Steiner
A new steering wheel may be the final touch for that treasured tractor you restored. Steiner Tractor in Lennon, Mich., appears to be the place to find whatever model you need - and most any other old tractor…
Read the complete story →From the archive · Full text
Reader shop tip
William Greyerbiehl, Bad Axe, Mich.
“Old stainless steel swimming pool ladders, the kind used in many portable pools, work great to do maintenance work around my farm. The ladder sets over the top of the pool and has rungs on each side to…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Lynden Jenkins
Lynden Jenkins says his brother-in-law was frequently breaking spindles on his Deere 4020 loader tractor, so he replaced the OEM spindles with the larger front end from a Deere 5010. Jenkins says fitting the heavier axles required reworking…
Read the complete story →From the archive · Full text
Reader shop tip
Andy Kozlowski, Califon, N.J.
“I use a car bumper jack from the 1970’s to lift my zero-turn mower so I can clean the deck and sharpen blades. I put a ring on the bumper jack’s hook and then put an S-hook on…
Read the complete tip →From the archive · Full text
Reader shop tip
John Travis, Dundee, N.Y.
“The pedal that’s used to raise or lower the 60-in. deck on my Ferris zero-turn riding mower was hard to push down, so hard that I eventually suffered a torn meniscus knee injury. Ferris makes a deck lift…
Read the complete tip →From the archive · Full text
Reader shop tip
Thomas G. Fargen, Plain, Wis.
“One of the handiest additions to my shop was hanging a cheap electric winch from the rafter that I can use to lift riding mowers, wood splitters, boat motors and motorcycles. Cheap and easy.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
William Sanford, Roxboro, N.C.
“I had an electric clutch fail on a 140 Deere lawn tractor. Instead of paying $400 plus for a new part from Deere, I sent it off to be repaired by a clutch rebuild company at a cost…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
William Sanford, Roxboro, N.C.
“Another tip I have is to buy oil change kits from auto parts stores and substitute mower or tractor filters for the automotive filters. Saves a lot of money.
Read the complete tip →From the archive · Full text
Feature story
Featured source: Jim Blackford
An old Snapper riding mower inspired Jim Blackford to build the forge he had wanted for decades. He flipped the mower deck upside down and welded it to a stand that puts it at the perfect working height.…
Read the complete story →From the archive · Full text
Feature story
Featured source: Dale Colvert
If your reliable, older model Tecumseh engine won’t start, a drop-in TCDI (Tecumseh Capacitive Discharge Ignition) from Overnight Solutions may be the answer. As the only bolt-in replacement available, the TCDI replaces the NLA 610748, 610855 and 610906…
Read the complete story →From the archive · Full text
Reader shop tip
“An owner of a 2011 Case-IH Farmall D40 recently reported that plastic fenders on the tractor had cracked. He replaced one and the other was starting to crack. I’ve found that you can usually prevent a crack like…
Read the complete tip →From the archive · Full text
Reader shop tip
Venna Trepasso, Sebastopol, Miss.
“A steering knuckle broke on a 1962 Massey Ferguson diesel tractor and the repair shop wanted about $500 to replace it. Instead, I welded a plate under the knuckle to stop it from popping out. The fix has…
Read the complete tip →From the archive · Full text
Reader shop tip
Jack Henning, Watertown, S. Dak.
“At 81 years old I’m no longer able to crank start my 1930 McCormick-Deering 10-20 tractor, so I mounted the starter ring gear off an IH 806 gas tractor on the 10-20’s belt pulley. I made a mounting…
Read the complete tip →From the archive · Full text
Reader shop tip
Michael Myers, Kirbyville, Texas
“I bought an old screw-type bottle jack cheap at a flea market and find that it’s real handy to use in my shop. One time I wanted to spread some metal pieces apart but found there wasn’t enough…
Read the complete tip →From the archive · Full text
Reader shop tip
Roman Bontrager, Myerstown, Penn.
“Years ago I was was working construction and we removed an x-ray machine from a medical office. The frame and rails attached to the ceiling. I took them down and reinstalled them in my shop. The two main…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Harold Mulder
Front axle extensions can turn rare Deere “vegetable tractors” into an even more rare, wide-track style. Harold Mulder ran across a Beet and Bean tractor with its skinny, 42-in. diameter rear wheels, long rear axle and wide front…
Read the complete story →From the archive · Full text
Reader shop tip
Anthony Siciliano, Redding, Ct.
“The axle on my 1993 Scag mower broke in half. Since it was welded into the mower’s frame, a replacement part would have cost $1,000. I cut out the old welds, removed the axle, and got a piece…
Read the complete tip →From the archive · Full text
Reader shop tip
James L. Fetzer, Maiden Rock, Wis.
“To remove the oil filter from my 2015 New Holland T4.75 tractor, I first have to remove the two fuel filters. Afterward, I have to call my neighbor – who is a service technician – to get the…
Read the complete tip →From the archive · Full text
Reader shop tip
Roger Gutschmidt, Gackle, N. Dak.
“The grain tank gearbox on my Deere combine, which moves grain from the clean grain elevator chain to the bubble-up auger in the hopper, failed a few years ago. A new one cost more than $2,000. The housing…
Read the complete tip →From the archive · Full text
Reader shop tip
Ted Lacey, Hay Manager, Trent, S. Dak.
“You can make an air preheater for gas or diesel tractors by taking heated air off the outside of the muffler and directing it through a pipe to the air cleaner. The preheated air goes down into the…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Brian Lough, Indian Head, Md.
“When repairing items with J-B Weld epoxy or other adhesives, I first apply a layer of epoxy. Then I place strips of storm window screen onto the epoxy to add strength to the repair. For even more strength,…
Read the complete tip →From the archive · Full text
Reader shop tip
Ted Kalvitis, Romney, W. Va.
“Congratulations to the FARM SHOW reader who beat a proposed $1,800 repair bill when the clutch cross-shaft on his Kubota tractor seized in the bell housing. While he realized success with a mixture of acetone and transmission fluid,…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Lyle Mack
Lyle Mack loves gear making so much he’ll even help you make your own. The young machinist set up LM Gear and Machine on his family’s farm to make gears, sprockets, and splined shafts.
Read the complete story →From the archive · Full text
Feature story
Featured source: Bob Lenz
“I make parts for the throttle shaft and new oversize hardened weight pins for Farmall governors,” says retired farmer and governor repair specialist Bob Lenz.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Randy Wyant
Precision Tractor Parts offers hard-to-find, U.S.-made parts for older International Harvester, Farmall and Cub tractors.
Read the complete story →From the archive · Full text
Reader shop tip
Alvin Francis, Evansville, Wis.
“For the second time in 20 years, the rear axle on my Case IH 60 Series combine broke. It must be a common problem because our local dealer has a skid loader attachment designed to lift the rear…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Paul Moore, Batavia, Ohio
“Oil began forming on the brake pads on my 1955 Minneapolis Moline 435 Mini Mo tractor. Roller bearings on both sides of the brakes were worn, which knocked out the seal between the transmission and brake shoes and…
Read the complete tip →From the archive · Full text
Reader shop tip
Garlon Peterson, Wild Rose, Wis.
“My old Sears riding mower sat around for a long time because the steering gear on it didn’t work. I finally got it fixed, but by that time the mower’s tires were flat from sitting so long. I…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Shawn Wagner, Plainwell, Mich.
“We had problems on my grandfather’s farm with panels on the combine breaking and cracking but were able to use JB Weld to solve the problem.
Read the complete tip →From the archive · Full text
Feature story
Featured source: Marlin Galde
A homemade grease gun extension makes it easy for Marlin Galde to lubricate the deck pulleys on his Deere 325 all-wheel-steer riding mower equipped with a 48-in. deck.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Chris McClure
The MaxJax lifting system by Danmar is a portable, two-post lift that can fit in any garage. Roll it into place and bolt it to preplaced, drop-in anchors. Hook it up to the mobile power unit, attach the…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Kevin Healy
Plan Tech uses a split-mold method instead of injection molding to make cast polyurethane drive and gear sprockets, pads and more. The result is a superior product with a process that can be used for custom parts, as…
Read the complete story →From the archive · Full text
Reader shop tip
Allen Davenport, Godfrey, Ill.
“I use an infrared temperature gun to check for bad bearings on our combine. I wait until I’ve been going for about an hour and then check them. Infrared temperature guns are relatively inexpensive now on the internet.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Briggs & Stratton
Changing the oil on lawn mowers and other outdoor power equipment can lead to messy spills. But with this new oil extractor pump, you don’t even have to remove the drain plug. You drop the tube into the…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Carl Hopkins, King George, Va.
“The pto shaft seal was leaking on my 3910 Ford tractor. The repair manual said to break the rear apart to fix. Instead, I screwed two sheet metal screws into the seal and used a slide hammer to…
Read the complete tip →From the archive · Full text
Reader shop tip
George Hillman, Jr., Batesville, Ind.
“I attached a bungie cord to the steering column on my Farmall H tractor in order to pull the slack out of the transmission gears, which keeps them from shimmying. I used the same idea on my Farmall…
Read the complete tip →From the archive · Full text
Reader shop tip
Stephen Hewes, Lyme, N.H.
“The splines on the power steering sector shaft on my Massey Ferguson 175 tractor stripped. Instead of replacing the entire assembly, I drilled through and used a tapered grade 8 bolt to secure it. I also welded to…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
David Simpler, Elkton, Md.
“I didn’t want water getting into the vertical slant-cut exhaust stacks on my tractors, but I couldn’t find an exhaust cover for them. Some farmers use a tin can as an exhaust cover, but the cans always blow…
Read the complete tip →From the archive · Full text
Reader shop tip
Jack B. Freeland, Mobile, Ala.
“The carburetor on my Deere 19 hp riding mower got gummed up after I used gas with ethanol. My local repair shop wanted $200 to clean the carburetor, and they had a 2-week service backlog.
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Ed Vieth
You can eliminate peeling paint on mufflers and manifolds by having them coated in ceramic. E & S Ceramic Coating can dress them up in either a black or silver coating.
Read the complete story →From the archive · Full text
Feature story
Featured source: Mark F. Burris
Mark Burris describes his Ford 8N as a best buy, but he has done a fair amount of tinkering on it. That includes dealing with a lack of oil pressure and learning how to partially split a tractor.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Glen Mlnarik
When International Harvester went out of business in the mid-1980’s, Glen Mlnarik got into the business of buying and selling IH parts. His dad and uncle were IH dealers for 26 years in Dodge, Neb., and Mlnarik bought…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Randy Raschein
“The factory steering valves on older tractors eventually break down internally. Our new power steering kit is built strong to last and will eliminate troublesome rebuilds. It works like factory steering, yet doesn’t destroy the tractor’s antique value…
Read the complete story →From the archive · Full text
Feature story
Featured source: Ron Post
“I’ve got a 45 year old Allis Chalmers 185 diesel that’s really hard to start when it’s below 50 degrees. I used to have it plugged in continuously about 6 months of the year and I know for…
Read the complete story →From the archive · Full text
Reader shop tip
Andrew Sewell, North Yorkshire, England
“I was talking to a farmer friend recently about how to limit fires on combines. Many farmers use a leaf blower to clean off any debris that might catch fire.
Read the complete tip →From the archive · Full text
Reader shop tip
Gerard E. Ouellette, Richmond, Maine
“A machinist friend and I built this overhead crane that pivots 180 degrees from side to side. I’m disabled and can’t lift anything so it’s one of the handiest tools in my shop. A trolley and chain hoist…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Joe Duggan, Rochester, Mass.
“To save time, I write the oil type, filter model, and wrench size needed on the wall near my tractors in our machine shed.”
Read the complete tip →From the archive · Full text
Reader shop tip
John J. Patterson, East Peoria, Ill.
“When I’m trying to solve problems on my older Ford and Farmall tractors, I get a lot of help from people at Yesterday’s Tractors, which is a website forum with lots of good folks (www.yesterdaystractors.com). One of the…
Read the complete tip →From the archive · Full text
Reader shop tip
Larry Wood, Waldo, Ohio
“I was using my riding mower recently and turned off the engine so I could pick up some sticks in the yard. When I got back on I couldn’t get the mower started.
Read the complete tip →From the archive · Full text
Reader shop tip
G.F. Donk, Clyde, N.Y.
“The drive pulley on my Ford flail mower worked loose and stripped the splines, so I had it replaced with a Browning clamp-on spline hub (www.applied.com/c-browningshq1hub/p/100790189). Bergman Electric in Auburn, N.Y., performed the work. The pulley was held…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Edwin Jordan
Longtime FARM SHOW reader Edwin Jordan says he has an easy way to prevent oil and liquid spills if you don’t have a funnel handy. Don’t remove the aluminum seal on the bottle of chainsaw bar oil, antifreeze,…
Read the complete story →From the archive · Full text
Feature story
Featured source: Norm Bennett
Norm Bennett got tired of constantly having to deal with dead batteries so he designed a system that uses a single trickle charger to maintain up to ten 12-volt batteries at the same time. The system consists of…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Mark Beiler
“The name Discbine Doctor is easy for people to remember when they need good used parts or a used machine,” says “Doctor” Mark Beiler, Ronks, Penn.
Read the complete story →From the archive · Full text
Feature story
Featured source: Norma Vaughn
“We diagnose problems fast, give people a fair estimate, and get the work done quick, because truckers need to get back on the road as soon as possible,” says Norma Vaughn of Kankakee Spring and Alignment. The Illinois…
Read the complete story →