Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW

Equipment

1669 shop tips and stories · page 9 of 28, newest issues first.

From the archive · Full text
Reader shop tip

Jay McCaman

Jay McCaman, Sand Lake, Mich.

“In a recent issue a reader complained about hydraulic oil transferring from the reservoir to the differential on Case 300 and 430 to 630 tractors. I worked at a Case dealership for 16 years and usually leakage of…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Earl Lumbra

Individual tip 1 of 2 from this reader’s published contribution.
Earl Lumbra, Montgomry Center, Vt.

“I put a jack from Tractor Supply on my home-built wood splitter to hold the front up when it’s not connected to a tractor. I should have done that 30 years ago.

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Gary Alford

Individual tip 1 of 2 from this reader’s published contribution.
Gary Alford, Edwardsburg, Mich.

“I installed a Pertronix electronic ignition and coil on my 1954 Ford 800 tractor and it worked out great. That old tractor has never run so well (www.pertronix.com).

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Raymond Hornak

Individual tip 2 of 2 from this reader’s published contribution.
Raymond Hornak, New Berlin, Wis.

“To keep batteries up to full charge on tractors or trucks parked for long periods of time, I use solar chargers that provide a trickle charge. It lets you park equipment anywhere without worrying about having electric power.…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Tom Chaney Sr.

Individual tip 2 of 2 from this reader’s published contribution.
Tom Chaney Sr., Chrisman, Ill.

“When the plastic hood on my Deere X500 lawn tractor shattered, Deere quoted me a price of $700 for a new hood. I didn’t want to spend that much when I figured it could just happen again. So…

Read the complete tip →
From the archive · Full text
Reader shop tip

Dale Rogers

Dale Rogers, dalecmrogers@gmail. com

“In your last issue (Vol. 39, No. 6), Herman Vander Vos wrote about his problems with push rods in his Husqvarna riding mower bending and breaking. My guess is the sticky engine valves were caused by using stale…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 4

Gary Holland

Individual tip 2 of 4 from this reader’s published contribution.
Gary Holland, (ladybug06@wildblue. net)

“Save hydraulic lines on your tractors and other equipment by covering them with insulated pipe wrap. It keeps fluid from cold in winter and heat in summer and prevents rot from sunlight. Most lines can be covered with…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Jonathan Dean

Individual tip 1 of 2 from this reader’s published contribution.
Jonathan Dean, Baskin, La.

“I have had terrible trouble with starters on Deere 4020’s not holding up. However, I discovered that if you replace them with a gear reduction starter, or one from a larger Deere tractor, they’ll start easily.

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Russell Spears

Individual tip 1 of 2 from this reader’s published contribution.
Russell Spears, Magnolia, Texas

“The steering bearing on my Ford 3600 tractor broke inside the steering gearbox. It was originally oil-filled but the oil goes bad and then the bearing is not lubricated. I fixed the problem by fitting the gearbox with…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Russell Spears

Individual tip 2 of 2 from this reader’s published contribution.
Russell Spears, Magnolia, Texas

“The fan belt on that 3600 tractor was always loose. I solved the problem by placing 3 small washers under the AC compressor to raise the compressor slightly, keeping the belt tight. Worked great.”

Read the complete tip →
From the archive · Full text
Reader shop tip

Bayard E. Young

Bayard E. Young, Elkwood, Va.

“I would like to share my experience with other readers that own an 8N Ford tractor with a 6-volt system. I recently installed electronic ignition that eliminates the points and condenser. It’s now a much better-running tractor. I…

Read the complete tip →
From the archive · Full text
Reader shop tip

Glen Allan

Glen Allan, Ontario, Canada

“In regard to Jerry Brandt’s problem with his LX188 Deere riding mower that was detailed in the last issue, the surging he experiences when he’s not running the mower deck could be caused by something loose in the…

Read the complete tip →
From the archive · Full text
Reader shop tip

Lee deVries

Lee deVries, Crawfordsville, Ore.

“Regarding Jerry Brandt’s ‘surging’ Deere garden tractor, I had a similar experience with a Deere mower that’s also equipped with the Kawasaki engine. It was surging badly when not under load and I had tried all the simple…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Milton Webster

Individual tip 1 of 2 from this reader’s published contribution.
Milton Webster, Taylor, Texas

“I came up with an inexpensive way to add water and antifreeze to my tractor tires, using the filter basket from an old automatic coffee maker and a 3-ft. length of clear plastic tubing. The filter basket forms…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Milton Webster

Individual tip 2 of 2 from this reader’s published contribution.
Milton Webster, Taylor, Texas

“I’ve used an old Chicago Pneumatic air hammer for years with a blunt chisel, to break down tire beads on yard tractors so I can remove tires without taking wheels off.”

Read the complete tip →