Practical ideas from FARM SHOW MagazineSubscribe · Free issue · Send us your shop tip
Subscribe to FARM SHOW

Equipment

1669 shop tips and stories · page 15 of 28, newest issues first.

From the archive · Full text
Reader shop tip 1 of 2

Lanny Vail

Individual tip 1 of 2 from this reader’s published contribution.
Lanny Vail, Bowman, N. Dak.

“The booster fuel pump on our 1951 Oliver diesel tractor that feeds the main fuel injection pump was leaking fuel into the engine oil. Not being able to find a new or rebuilt tractor pump to fit, I…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Lanny Vail

Individual tip 2 of 2 from this reader’s published contribution.
Lanny Vail, Bowman, N. Dak.

“For Ford 9N, 2N, and 8N tractors, the newer Hy-Tran oils that go into the rear end and hydraulic system are a little thin for the tractor’s lift system to work smoothly. One solution is to mix your…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 3

Bruce Ashick

Individual tip 1 of 3 from this reader’s published contribution.
Bruce Ashick, Pembroke, Ont.

“The rubber on the crimp rollers in my Deere mower-conditioner started coming off in pieces. To solve the problem I removed the rollers, stripped off the rubber, and then welded straight 3/4-in. sq. rod on the rollers to…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 3

Bruce Ashick

Individual tip 2 of 3 from this reader’s published contribution.
Bruce Ashick, Pembroke, Ont.

“The rubber gearshift boots on my tractors kept tearing and getting hard, even though the tractors are stored in a shed when not in use. To solve the problem I took a heavy rubber tube and cut round…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Larry Genge

Individual tip 1 of 2 from this reader’s published contribution.
Larry Genge, Glovertown, Newfoundland; ph 709 533-2798, [email protected]

“I built this 20-ton press from scrap metal, using 10-in. channel iron for the side posts and 6-in. channel iron for the bed. I can use 3 different sizes of interchangeable dies with it, ranging from 3/4 to…

Read the complete tip →
From the archive · Full text
Reader shop tip

Dick Clevenger

Dick Clevenger, 17174 County Road G40, Letts, Iowa 52754 (ph 319 726-3502)

“I’ve owned a 1955 Allis Chalmers CA with an L-306 Woods belly mower for 20 years. It’s pretty much bullet-proof except for one thing – if you move the adjuster idlers to tighten the belt, it’ll start wearing…

Read the complete tip →
From the archive · Full text
Reader shop tip

Louie Waelti

Louie Waelti, Monroe, Wis.

“I wanted to place an aluminum ladder up against my tractor’s hood without scratching it. So I placed a 5-ft. strip of 3/4-in. self-adhesive, auto body rubber trim on back of the ladder’s rails. Such body trim is…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Roger Gutschmidt

Individual tip 2 of 2 from this reader’s published contribution.
Roger Gutschmidt, Gackle, N. Dak.

“I’ve found endless uses for rare earth magnets around the shop. I have steel walls and cabinets in my shop so I’ve got these little magnets stuck all over the place, holding parts, manuals, etc. They’re so unbelievably…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 3

Gilbert F. Conn

Individual tip 2 of 3 from this reader’s published contribution.
Gilbert F. Conn, Pittsburgh, Penn.

“The steering wheel on my 1948 Deere A tractor was all chewed up and had deep cracks around the wheel’s three spokes. I used Billy Mays Mighty Putty to build the wheel back up to its original condition,…

Read the complete tip →
From the archive · Full text
Reader shop tip 3 of 3

Steve Reeves

Individual tip 3 of 3 from this reader’s published contribution.
Steve Reeves, Benton, Ky.

“I have problems with arthritis, which makes it difficult to lay on a shop floor and work on equipment. To solve the problem I use a motorcycle hoist. It lets me raise the equipment to working height and…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 3

Trevor Bruntlett

Individual tip 1 of 3 from this reader’s published contribution.
Trevor Bruntlett, Chelan, Wash.

“Recently I bought a 2002 lawn tractor used and soon discovered someone had put something in the fuel tank that gummed up the entire fuel system. The plunger for the carburetor’s fuel metering system broke, and unfortunately I…

Read the complete tip →
From the archive · Full text
Reader shop tip

Alden Corp.

Alden Corp., 251 Munson Road, Wol- cott, Ct. 06716 (ph 800 832-5336; www.aldn.com)

This company sells extraction tools driven by standard 3/8 and 1/4-in. reversible power drills, that make it easy to remove stripped or broken bolts and other threaded fasteners. The “ProGrabit” works on anything from a no. 4 screw…

Read the complete tip →
From the archive · Full text
Reader shop tip

Brad Cole

Brad Cole, Skaneateles, N.Y.

“My Kubota 4-WD tractor came equipped with industrial tread tires. Unfortunately there was no clearance for tire chains and I didn’t want to replace the wheels and tires. Instead I installed Tungsten studs in the tires, which greatly…

Read the complete tip →
From the archive · Full text
Reader shop tip 1 of 2

Zachary Vahlkamp

Individual tip 1 of 2 from this reader’s published contribution.
Zachary Vahlkamp, Oakdale, Ill.

“I own two older Grasshopper riding mowers that are simple, reliable and easy to maintain. However, I had a problem keeping the deck drive belts, especially the rear belt, from falling off the pulleys. The tensioning pulley is…

Read the complete tip →
From the archive · Full text
Reader shop tip 2 of 2

Zachary Vahlkamp

Individual tip 2 of 2 from this reader’s published contribution.
Zachary Vahlkamp, Oakdale, Ill.

“I’ve worked on farm and construction equipment for more than 10 years and have noticed that people tend to bend the parking lock linkage on IH 06, 56, and 66 series tractors. Tisco makes a spring-loaded replacement linkage…

Read the complete tip →
From the archive · Full text
Reader shop tip

David Chalmers

David Chalmers, Mancelona, Mich.

“I bought a Farmall Super C tractor equipped with a 1-row cultivator but without a 3-pt. hitch or a quick hitch. I made a front-mounted 3-pt. hitch using Ford 8N tractor parts and some ingenuity. I can operate…

Read the complete tip →
From the archive · Full text
Reader shop tip

Randy Boykin

Randy Boykin

“In a recent issue William Merendini of Brodheadsville, Penn., reported that his 2008 Deere 3720 tractor was unstable and felt dangerous to use. In my opinion, the problem isn’t with the tractor but with the operator and the…

Read the complete tip →