From the archive · Full text
Feature story
Featured source: Chris Kornkven
PVC tubing works great for adding oil to engines, transmissions and rear ends where there’s not enough room to pour out of a standard quart oil container, says Chris Kornkven, Helenville, Wis.
Read the complete story →From the archive · Full text
Feature story
Featured source: North American Oil
Brush-on liquid electrical “tape” is superior to tape on a roll because it forms a tighter seal against dirt and moisture and it won’t work loose due to vibration, according to the manufacturer, North American Oil.
Read the complete story →From the archive · Full text
Feature story
Featured source: Dale Flohaug
When Dale Flohaug went to school in a one-room school house as a young boy, he never dreamed he’d spend hundreds of hours in the building later in life. But that’s what happened because he uses the tiny…
Read the complete story →From the archive · Full text
Feature story
Featured source: Jim Deardorff
“You can get an extra $1,000 for a shiny combine over a dull one,” says Jim Deardorff, president of Superior Coatings, about a product called Kleen Kote that stops rust and re-stores old paint.
Read the complete story →From the archive · Full text
Reader shop tip
Albert L. Url, 4117 E. Briges Road, Elk, Wash. 99009 ph 509 292-5119
“I came up with a way to align a shaft without using any tools. I got the idea while installing a Plymouth 318 cu. in. car engine in an International 4-WD truck. The Plymouth engine has a longer…
Read the complete tip →From the archive · Full text
Reader shop tip
George Wissinger, Huntington, Ind.
He fixed a common problem on his 1963 New Holland 268 small square baler.
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Hebert Wodtke, Loogootee, Ill.
“I replace farm wagon tires with used 16-in. pickup tires. I like tires with 8-ply or more. Rather than buy tubes, I use a liberal amount of talc seed lubricant in each tire and on each bias tube.…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Hebert Wodtke, Loogootee, Ill.
“I believe in preventative maintenance, so whenever a motor vehicle reaches 16 years of age I start checking prices for a replacement radiator even if there’s nothing wrong with the one I already have. In my opinion, a…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Mark Burrow, 11221 N. 100 th St., Altamont, Ill. 62411 ph 618 483-5598
He also came up with a unique way to transport gas welding tanks that makes use of an ordinary hand truck. He constructed a metal stand for the welding tank, leaving a bit of extra space below the…
Read the complete tip →From the archive · Full text
Reader shop tip
Robert Ellis, High Hill, Mo.
“I designed this tool to loosen the belt that drives the pickup on older model Vermeer balers to make it easier to grease the bars at each end of the pickup. It saves a lot of skinned knuckles,”…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
When David Curtis took an early 1980’s Cadillac to a junk yard to scrap it, they wouldn’t take it because he didn’t have the title.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Since they retired, Lester Rose and his wife, Andrea, have lived on the road for the past 13 years with no permanent address (see re-lated story on page 39). In that time they learned that the hitch pulling…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Anyone who does repair work will be interested in this new rig that allows you to make on-site service calls, and also works great as a backup hoist for shop work.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Lester Rose and his wife, Audrea, live on the road doing volunteer construction work, made possible by their fully equipped workshop.
Read the complete story →From the archive · Full text
Feature story
Featured source:
If you drive a semi-tractor, you probably keep the engine running whenever you drive to a location and are waiting to load or unload a shipment. That keeps the cab warm in winter and avoids difficult restarts of…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Working fields as far as 35 miles from home is less of a hassle than it used to be for Cary Urka, thanks to a couple of service trucks he customized for farm work.
Read the complete story →From the archive · Full text
Reader shop tip
Steering Wobble On GM Pickups
On 1973 to 1991 GM vehicles equipped with steering column tilt assembly, often the assembly comes loose and wobbles as the vehicle ages. Most people believe the column is worn out but that’s not the case. For some…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Dave Nicholas, Martinsville, Ohio
“Whenever I find a big discount store like Walmart with rubbing alcohol on sale for 25 cents a pint or so, I buy a case. Twice a year, around Easter and Thanksgiving, I dump a pint of rubbing…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Dave Nicholas, Martinsville, Ohio
“Once every year I put two teaspoons of brake fluid into the auto transmissions on my vehicles. The brake fluid keeps the front seal and other seals inside the transmission soft so they don’t crack and dry up.…
Read the complete tip →From the archive · Full text
Reader shop tip
Jason Godfrey, ph 828 453-8527; email
[email protected]: “On the farm working out of my truck, I sometimes find myself needing a vise for tough jobs. So I came up with this simple vise stand that fits into the receiver hitch on my pickup. The…
Read the complete tip →From the archive · Full text
Reader shop tip
Lee W. Pedersen, 78 Taft Ave., Lynbrook, N.Y. 11563
Pedersen sells a new alcohol-resistant gas tank sealer for gas engines, tractors, cars, trucks, boats and planes. It’s formulated to resist most gasoline additives such as alcohol and methanol.
Read the complete tip →From the archive · Full text
Feature story
Featured source:
You can recycle cordless drills by replacing the worn-out batteries with an old electric cord and a couple of alligator clips. Then, any 12-volt car, truck, or tractor battery can become a power source, says Gary Goldsberry, Stillwater,…
Read the complete story →From the archive · Full text
Feature story
Featured source:
When the diesel engine wore out on his 1956 IH crawler tractor, Kevin Cohrs, Glencoe, Minn., found a low-cost way to repower it with a diesel engine out of an IH 4386 4-WD tractor.
Read the complete story →From the archive · Full text
Feature story
Featured source:
There’s a ’84 Ford F-250 3/4-ton pickup in New Jersey that’s had an unconventional life. There were more than 270,000 miles on its original 351 engine before it was replaced in 1995 with an Oldsmobile diesel engine that…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Brian Maring of Eddyville, Nebraska, spent only $1.50 and about two hours of time to make a tool that would cost him $300 to $350 to buy at a tire shop.
Read the complete story →From the archive · Full text
Feature story
Featured source:
“It lets me do repair work outside even when it’s raining,” says Lee Schunk, Clare, Mich., about his home-built service truck that’s equipped with a pair of “roofed” toolboxes, one on each side.
Read the complete story →From the archive · Full text
Feature story
Featured source:
“It puts everything up high enough that I can service it easily,” says Harold Davis, Trenton, Tenn., about the service rack he built for his Deere garden tractor equipped with a 60-in., belly-mount mower.
Read the complete story →From the archive · Full text
Reader shop tip
Herman Vander Vos, Bozeman, Mont.
“I own a 1968 Ford pickup with the fuel tank behind the seat. The design makes it very easy to insert a hose to siphon out gas, which I suspected someone was doing.
Read the complete tip →From the archive · Full text
Reader shop tip
John F. Wohlwend, Foxboro, Wis.
“If you have a tubeless tire that goes flat and is still on the vehicle, and the tire won’t take air because the bead is off, take the valve out of the stem and then jack the trailer…
Read the complete tip →From the archive · Full text
Reader shop tip
E. “Woody” Johnson, Osakis, Minn.
“To fix leaking radiators on tractors and vehicles, I’ve had great luck using Silver Seal heavy duty stop leak (www.AutoBarn.com; ph 888 484-9560). It stops leaks quickly, in-hibits rust, and lubricates the entire cooling system. It builds a…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Randy Rundle’s frustration starting old pickups led to a better idea and his own business. Fifteen years later, his Fifth Avenue Auto Parts, located in Clay Center, Kansas, supplies parts and solutions to everything from antique cars, boats,…
Read the complete story →From the archive · Full text
Feature story
Featured source:
“Our 1966 Ford pickup with 98,000 miles burned oil and the ring gear on the flywheel was going out. I bought a 1984 Chevy conversion van with a 6.2 diesel and dropped the sub frame out of it,…
Read the complete story →From the archive · Full text
Reader shop tip 3 of 4
Individual tip 3 of 4 from this reader’s published contribution.
Bill Reeks, Cromwell, Ky.
I also install a ball hitch on front of each tractor for backing trailers into sheds.
Read the complete tip →From the archive · Full text
Reader shop tip
Clendon Nichols, Union, Ky.
After years of having tractor wheel rims rust out due to the corrosive effect of the calcium solution he put into the tires, Clendon says he finally came up with a rustproofing solution that works great.
Read the complete tip →From the archive · Full text
Reader shop tip
Pat Prom, Eden Prairie, Minn.
“I used 1/4-in. thick scrap metal to build my own 5 1/2-ft. high engine hoist. The hoist is raised and lowered by a 5-in. dia., 3-ton hydraulic cylinder. I use it to lift engines and transmissions out of…
Read the complete tip →From the archive · Full text
Reader shop tip
Arthur H. Harms, Estelline, S. Dak.
“I have two vehicles that both ran hot during the summer - a 1976 Dodge pickup and a 1981 Mercury car equipped with a 302 cu. in. engine. I made two modifications to solve the problem. First, I…
Read the complete tip →From the archive · Full text
Reader shop tip
Michael Pigorsh, Northco Products LLC, P.O. Box 1093, Big Rapids, Mich. 49307 (ph 231 527-1660; fax 231 527-1665; email
[email protected]; website: www.rustreaper.com): “We think our new
Read the complete tip →From the archive · Full text
Reader shop tip
Pete M. Friesen, Meade, Kansas
“I had a problem with the anhydrous ammonia hitch on my V-blade tillage implement. It was hard to reach to pull the spring-loaded pin and, with the other arm, pull the hitch back at the same time. So…
Read the complete tip →From the archive · Full text
Reader shop tip
Trevor Shute, RR 6, Guelph, Ontario, Canada N1H 6J3 (ph 519 822-6705)
“Here’s a tip to prevent scalping or ripping out chunks of lawn when plowing snow. I removed the skid plate from the bottom of my 7-ft. scraper blade and replaced it with a section that I cut from…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Here’s an idea we recently spotted in Four Wheeler Magazine (www.fourwheeler.com).
Read the complete story →From the archive · Full text
Feature story
Featured source:
By cutting down an old 1,000-gal. propane tank, Lonnie Nichols, Copeland, Kansas, was able to build a portable “oil vac” that he uses to remove used oil from irrigation engines. A second tank on the trailer carries fresh…
Read the complete story →From the archive · Full text
Feature story
Featured source:
If you own an older Ford pickup with a rusted-out tailgate, you’ll be interested in this replacement tailgate that looks just like the original. It’s available from an Oklahoma company that specializes in classic pickup bed parts for…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Not many people build their own brake presses to bend sheet metal, but Wilfred Mollenbeck made a giant one with a 20-ft. wide bed. It measures 15 ft. high and weighs about 18,000 lbs. A hydraulic power pack…
Read the complete story →From the archive · Full text
Feature story
Featured source:
“If I was putting up a new building, I’d build it this way. It gives me more room to work and also lets in a lot of light,” says Mark Bruellman, Rolfe, Iowa, who raised a section of…
Read the complete story →From the archive · Full text
Reader shop tip
John Lindemer, Ind.
Several years ago, a neighbor of John’s had problems with frozen pipes. The problem was compounded by the fact that the frozen pipes were made of pvc instead of copper so he couldn’t use his welder to thaw…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
It took Jacob May only about an hour to make a set of portable car ramps, using nothing but his cutting torch, welder and a bit of scrap metal.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Dan Jacobson, Pequot Lakes, Minn., doesn’t have a tailgate on back of his pickup. That’s because he often uses the pickup bed as a work table in the shop or field. One of his handiest tools is a…
Read the complete story →From the archive · Full text
Feature story
Featured source:
“I came up with a way to charge older Deere diesel tractors for less than $100,” says Ken Armstrong, Point, Texas.
Read the complete story →From the archive · Full text
Feature story
Featured source:
When Glenn and Gordon Marshalek, Raymond, Nebraska, needed to pull the engine and transmission from a garbage truck, they realized their normal engine hoist might not be able to handle it.
Read the complete story →From the archive · Full text
Feature story
Featured source:
It’s nice to be able to take the welder to the job, and not always the job to the welder, according to Aron Wiebe of Niverville, Manitoba, who built his own mobile system, which he says works well…
Read the complete story →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Walter Brenner, Bredenbury, Sask.
“The wheel rims on my 1990 GMC 1/2-ton pickup fit very tight on the hubs. They are difficult to remove when you need a tire change. If I have to change a tire, I loosen all the wheel…
Read the complete tip →From the archive · Full text
Reader shop tip
Guy Ramsey, Nenana, Alaska
“I just paid $411 to have a fuel pump replaced in my 1990 Chevrolet 4-WD pickup, plus $240 to have it hauled 60 miles to Fairbanks. Can anyone tell me how GM came up with the absurd idea…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
“It’s lightweight and much easier to use than hydraulic lifts and can be built a lot cheaper,” says Bruce Graham, Tyler, Texas, about his air-powered shop hoist.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Lloyd Meffert, Hettick, Ill., does repair work for area farmers. When he heads out on a call, he always takes his home-built, 2-wheeled “repair trailer”.
Read the complete story →From the archive · Full text
Reader shop tip
Joseph Palicka, Aitkin, Minn.
“I made a simple 6-terminal throw switch in order to raise and lower my truck-mounted snowplow blade. It allowed me to convert my 12-volt winch, which would only power up, to power down, also. The throw handle sides…
Read the complete tip →From the archive · Full text
Reader shop tip
Roger and Bruce Elliott, Montrose, Ill.
“We made a rolling support for the heavy pieces of machinery that are worked on in our shop. The roller is actually 6-in. pipe mounted on telescoping pieces of square piping. This allows it to adjust for height.…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Cary Urka, Brethren, Mich.
“Pickup-mounted snow blades can be difficult to install. To make the job easier, I mount the blade on a pallet jack. I wheel the blade up to the pickup, then use the hand jack to raise the blade…
Read the complete tip →