From the archive · Full text
Feature story
Featured source: Henry Daugherty
Henry Daugherty turned a worn-out pickup truck bed into a rugged flat bed equipped with a crane, storage and more. It has a rebuilt cab and an 80 by 108-in. treated lumber bed with internal 1 3/4 by…
Read the complete story →From the archive · Full text
Feature story
Featured source: Chester Kimber
“After hurting my back lifting the loading ramps on our flatbed trailer, I decided I had to do something to make the job easier,” says Chester Kimber, Amistad, N. Mexico.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Brandon Jacobs
Back in 2016, Geno’s Garage of Cumming, Ga., needed to find a dashboard replacement for their 1999 Dodge truck. They soon found out they weren’t the only ones in need of a new dash.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Clint Reynolds, Clarksville, Tenn.
“I got tired of untangling tie-down straps and battery cables that I keep in my truck toolbox. So I cut the corner out of some gallon antifreeze jugs and use them to hold straps, cables and log chains.…
Read the complete tip →From the archive · Full text
Reader shop tip
Don Raucstadt, Seligman, Mo.
“I used a brake drum off a semi truck axle to make a solid base for a free-standing vise. I welded steel plates to both ends of channel iron uprights and bolted the bottom plate to the brake…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Miles Brett
Miles Brett was hired for maintenance and trouble shooting at a Calgary, Alberta, business with a yard filled with thousands of steel 55-gal. drums which used to hold rubberized asphalt crack filler. Brett had to come up with…
Read the complete story →From the archive · Full text
Reader shop tip
Gary Swensen, Yankton, S.Dak.
“I bought two extra mounting brackets for the jack on my old trailer and mounted one on each side of the trailer. Now, if I have a flat while pulling the trailer, I just attach the jack to…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Karl Scheibengraber, Lisbon, Wis.
“Whenever I would lay down a piece of cardboard and lay down on my side to service or repair vehicles, I would get a sore neck if I didn’t support my head somehow. Old pillows or a folded…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Marty Heilman
Ever filled up your car with gas, but had the gas splash back and dribble down the side of your vehicle? To keep that from happening, a few years ago Marty Heilman, Andover, Minn., designed a rubber bib…
Read the complete story →From the archive · Full text
Feature story
Featured source: Michael Veatch
Michael Veatch, Republic, Mo., modified a jack-operated shop engine hoist so that it can be quickly attached to the receiver hitch on his pickup.
Read the complete story →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Gary L. Ahlbrecht, Brownton, Minn.
“Every year I use a remote-controlled plug-in module to turn my outdoor Christmas lights on and off. I use the same unit the rest of the winter to remote-start the block heater on my diesel lawn tractor, which…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Don Campbell
Don Campbell maximizes every square inch of his relatively small shop by putting his 3 amazing workbenches on wheels so he can move them around the shop, into his adjoining garage, or to an outside pad to work…
Read the complete story →From the archive · Full text
Reader shop tip 1 of 4
Individual tip 1 of 4 from this reader’s published contribution.
Preston Williams, Victoria, Va.
“The oil check light wouldn’t go off in my 2012 Chevy truck. I had a guy pull the sending unit and change the screen under it. Now it’s okay.
Read the complete tip →From the archive · Full text
Reader shop tip
Ron Ziegler, Flying Z Ranch, Los Alamos, Calif.
“Our 1985 Ford truck stopped running because of an electrical problem, and with all the pollution control equipment it was impossible to find what was wrong. So we removed all the wiring and pollution control equipment, and then…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Todd Schminke
Todd Schminke says that if you have some metal parts to paint, you’re better off with “do it yourself” powder-coating. It’s cheaper, and the coating lasts longer. Schminke was frustrated when a receiver hitch holder he built started…
Read the complete story →From the archive · Full text
Feature story
Featured source: Seth Ross
Tac Glue™ adhesive won’t dry up in an open bottle and it works on most materials. It dries quickly once applied and sells at a reasonable price considering that it provides industrial strength, according to Tac Glue owner,…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip 4 of 4
Individual tip 4 of 4 from this reader’s published contribution.
Milan Hochstetler, Cumberland, Va.
“My pickup has manual crank windows, and when I’m behind the steering wheel I can’t reach all the way over to open the passenger window. I attached a short piece of pvc pipe over the handle, so I…
Read the complete tip →From the archive · Full text
Reader shop tip
Ted Lacy, Worley, Idaho
“The best $16 I’ve ever spent was buying two transmitters for the Liftmaster door opener on my shop’s big roll-up door. I put one transmitter on my utility tractor and the other one in my pickup. Sure beats…
Read the complete tip →From the archive · Full text
Reader shop tip
The Eastwood Company, www.eastwood.com; ph8003439353 (as printed)
Eastwood says its gas tank sealer kit is an inexpensive way to easily repair worn gas tanks. It keeps rust out of your vehicle’s fuel system and seals minor leaks. Works in tanks containing gasoline, gasohol, or diesel.…
Read the complete tip →From the archive · Full text
Reader shop tip
Steve Faber, Tiffin, Ohio
“I’ve found that I can easily break beads on tubeless tires using my trailer tongue jack. A short piece of bar stock placed along the edge of the rim makes it more effective.”
Read the complete tip →From the archive · Full text
Feature story
Featured source: Allan Shepard
“A person could spend more than $30,000 to buy the extra horsepower you get from a Case IH 450 tractor compared to a Case IH 350, or they could spend about $2,000 for one of our performance modules…
Read the complete story →From the archive · Full text
Feature story
Featured source: John Kokur
John Kokur, Carlisle, Iowa, updated his 1993 Kawasaki Mule with electric power steering, spending a total of only $160.
Read the complete story →From the archive · Full text
Feature story
Featured source: KC Innovations
Whether you want to start a vehicle’s dead battery or you just need a portable AC power unit, you’ll be interested in these 2 new products from KC Innovations, Loogootee, Ind. Both make use of commonly available DeWalt,…
Read the complete story →From the archive · Full text
Feature story
Featured source: Jack Ziegler
When Jack Ziegler and his son Colton were offered an old pole barn and several grain bins for free, they started thinking of ways to use them. They decided to turn them into several different buildings, including a…
Read the complete story →From the archive · Full text
Reader shop tip
Doug Johnson, Aberdeen, Wash.
“When pouring bar oil into the small opening on my chainsaw from the gallon jug it comes in, trying to ‘hit the hole’ often results in spilled oil all over me and the saw. I found that pint-sized…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Fondy Auto Electric, Fond du Lac, Wis. (ph 800 236-2701; www.fondyautoelectric. com)
Fondy offers a large inventory of new and remanufactured starters, generators and alternators to fit any vehicle, including cars and light and heavy-duty trucks as well as motorcycles, ATV’s, and snowmobiles. They say that if they don’t have…
Read the complete tip →From the archive · Full text
Reader shop tip
Larry Wood, Waldo, Ohio
“Tired of your trailer making noise when you travel down the road? I have a Ford F-350 with a 2 1⁄2-in. receiver hitch so I use a sleeve adaptor so our 2-in. ball hitch will work properly. But…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
SpynTec Industries, North Lima, Ohio (ph 888 290-2953; www.spyntec.com)
This company is the leader in fixed spindle hub conversions and recently released a new line of fixed spindle conversion kits for 2000-2015 Dodge 3500 dual rear wheel pickups. They also offer hub conversions for 1994-2010 Dodge, 1999-2010…
Read the complete tip →From the archive · Full text
Reader shop tip
Tim Ojala, New Ipswich, N.H.
“When working on radiators in older vehicles, often the drain valve is stuck. So when we need to drain or lower the level of liquid to add antifreeze, I use a siphon hose through the radiator cap.”
Read the complete tip →From the archive · Full text
Reader shop tip
Tony Ryba, Johnstown, Penn.
“Wanting to inspect the brakes on my Ford truck, I found that all 4 wheels were stuck to the rotors. Working on one wheel at a time, I applied penetrating oil to the joint between the rotor and…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Dave Meiners
Dave Meiners uses the receiver hitch on his pickup, 2-in. square tubing, and a come-along to lift his riding mower so he can clean the deck and sharpen the blades.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Steve Harman
If a bent tube is needed, Tubular Techniques can provide it, no matter what it’s for. The company has bent tubes to make butterfly nets for the Ohio State University Department of Entomology and tubes for F-16 fighter…
Read the complete story →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Ben Parks, Austin, Texas
“When I did a mechanical restoration of my 1970 Jeep, the first thing I did was to replace the distributor points with a Pertronix ignition kit (www.pertronixbrands.com; ph 909-599-5955). I also installed a Pertronix ignitor coil. With the…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Konnor Bjelland
Instead of bending over to work on equipment, 6-ft. 2-in. tall Konnor Bjelland built a big workbench on back of his service truck that stands more than 1 ft. taller than the small factory bumper it replaced. He…
Read the complete story →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Gary Swensen, Yankton, S.Dak.
“I bought a small 900-watt 2-cycle $99 generator with one outlet from Harbor Freight. It’s handy to carry around to run a battery charger, small air compressor, and lights when out in the field. I used to keep…
Read the complete tip →From the archive · Full text
Reader shop tip
Steve Faber, Tiffin, Ohio
“I had a hitch that was slightly loose in the receiver tube, as they usually are. Besides the annoying rattle, the utility trailer swayed slightly but continuously. I sorted through my scrap metal until I found just the…
Read the complete tip →From the archive · Full text
Reader shop tip
Ted Lacy, Worley, Idaho
“The best $16 I ever spent was for 2 extra transmitters for the Liftmaster opener on the big roll-up door on my shop. I put one on my utility tractor and the other one in my pickup. Sure…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Gary Haak, The Ultimate Mat (www. theultimatemat.com; ph 605 360-8474)
Gary figured there had to be something better than using a big piece of cardboard every time he needed to work under a combine or truck. His answer? The Ultimate Mat, a 4 by 6-ft. heavy-duty fabric mat…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Bryan Haugen, Larry Roed, and Nick Harker
Bryan Haugen, Larry Roed, and Nick Harker have more than 30 years experience supplying tracks, replacement parts for track systems, and track conversion systems direct to farmers. Their business is called TrackFarmer.com.
Read the complete story →From the archive · Full text
Feature story
Featured source: Mike Toppen
Mike Toppen, Allegan, Mich., tapped the back side of an old Jacobs drill press chuck with 5/8-11 thread, allowing him to also use his DeWalt cordless angle grinder as a right angle drill.
Read the complete story →From the archive · Full text
Feature story
Featured source: Dennis Hartmann
“I salvaged the hydraulic jack off an old dump trailer to build this infinitely adjustable roller stand. I use it with my lathe and mill, and sometimes my welding table when handling long material. It works great to…
Read the complete story →From the archive · Full text
Feature story
Featured source: Dave Auble
“Our new external tire patch for tubeless tires eliminates the need to remove the wheel from the rim to patch punctures or slices in tractor tires and other off-road tires, even if it’s a tear in the sidewall.…
Read the complete story →From the archive · Full text
Feature story
Featured source: Mike Peters
“I recently read a story in FARM SHOW about a portable bench vise that attached at hitch level to a pickup bumper. The operator had to lean over to use it. It prompted me to put together a…
Read the complete story →From the archive · Full text
Feature story
Featured source: Gordon Mariner
“I recently built an overhead crane that’s one of the handiest tools in my 30 by 60-ft. home-built shop,” says Gordon Mariner, Goodlettsville, Tenn.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Pro Eagle
This new “big wheel” off-road floor jack from Pro Eagle is equipped with a pair of large diameter wheels on back, making it much easier to maneuver on uneven ground than a jack with 4 smaller wheels. The…
Read the complete story →From the archive · Full text
Reader shop tip
Butch Beck, Hope, Arkansas
“The use of a 2-post car lift is not only great for working on cars and light trucks, but the arms can be used to hold equipment at a convenient working height. Very handy.”
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Joe Eilert, Jewell, Kan.
“We have had problems with vaporlock in our 427 Chevy trucks. I’ve found the best solution is to avoid gas with ethanol, which boils at a lower temp.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Wess Cornelius, Winlock, Wash.
“When fixing a broken window, you can avoid making a mess inside the house or vehicle by putting duct tape over what remains of the window before removing it. Keeps shards of glass from going everywhere.”
Read the complete tip →From the archive · Full text
Feature story
Featured source: Michael Heron
“I made these garden tractor stands by cutting a wheel rim from a 1/2-ton pickup in half, then welding a pair of wide channel iron brackets onto each half rim. The plates are the same width as the…
Read the complete story →From the archive · Full text
Feature story
Featured source: Lucas Greff
“When working on semi trailer air brakes, it’s difficult to diagnose problems by yourself. You have to walk back and forth from the tractor to activate and deactivate the brakes. Also, with the tractor engine running it was…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: QuickJack
Anyone who does a lot of maintenance work on cars and trucks in their shop will like this new QuickJack portable car lift that eliminates the need for conventional jacks and stands. The electric-hydraulic lift raises and lowers…
Read the complete story →From the archive · Full text
Feature story
Featured source: Lee Johnson
“I built this infinitely adjustable roller stand out of round stock and square tubing. I use it with my bandsaw when handling long material. A trailer jack makes it easy to adjust the height,” says Lee Johnson, Richburg,…
Read the complete story →From the archive · Full text
Feature story
Featured source: Alvin Beechy
When Alvin Beechy started using magnets in his Amish buggy shop to hold windows open or shut, he had no idea others would find so many uses for the magnets. Now his LaGrange, Ind., business carries a large…
Read the complete story →From the archive · Full text
Feature story
Featured source: Steve Beals
“I started the business after looking for parts for my tired old 1974 International Scout II and nobody had them,” says Steve Beals.
Read the complete story →From the archive · Full text
Reader shop tip
Andrew Horst, Excel-ER-ate LLC, 20918 Millers Church Rd., Hagerstown, Md. 21742 (ph 240 382-0459)
“Factory- installed receiver hitches on Chevrolet Silverado 2500 and 3500 pickups made from 2001 to 2010 have experienced failures while towing heavy loads. The hitches just aren’t strong enough,” says Horst.
Read the complete tip →From the archive · Full text
Reader shop tip
Steve Faber, Tiffin, Ohio
“Many spray cans for paint, penetrating oil, and solvents have a dot marking the orientation of the pickup tube inside the can. The dot always seems to get washed away by the contents of the can so before…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Wayne Hamel, Hopwood, Penn.
“I added 3 chain links to my ratchet straps so the ratchet body does not ride on the corner of my trailer frame. Works great.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Wayne Hamel, Hopwood, Penn.
“I also added 4 LED lights to the outside edges of my trailer and 12 small bed lights to help see the trailer and where I’m backing up at night. It’s a big help.”
Read the complete tip →