Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Jim Rist
Cat. 5 wire can be used to make handy, inexpensive multi-purpose ties, says Jim Rist of Granbury, Texas. He recently sent FARM SHOW samples of the ties he makes by pulling wires out of damaged sheathing and then…
Read the complete story →From the archive · Full text
Reader shop tip
A.J. Fries, Oregonia, Ohio
“To get a tire bead to seat on a car, pickup, garden tractor, or other smaller tires, I wrap a ratchet strap around the outer diameter of the tire and tighten it down to bring the bead close…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Don Stewart, Mountain Grove, Mo.
“We put a lot of used tires on our farm vehicles, so slow tire leaks around the wheel rims is a common problem. I came up with a cheap tire seal by filling an empty plastic dish soap…
Read the complete tip →From the archive · Full text
Reader shop tip
Jerry Hawkinson, Gettysburg, S. Dak.
“One of your readers commented in the last issue about how the 50-50 mix of ATF and acetone that he uses as a penetrating fluid keeps evaporating. I use a sturdy metal container from Assman Shop Supply (ph…
Read the complete tip →From the archive · Full text
Reader shop tip
Kevin Ericson, Axtell, Neb.
“I bought a used 2-post car lift at auction for $800. The capacity is 9,000 lbs., which will handle our pickups. I even trust it with my 1935 Ford.”
Read the complete tip →From the archive · Full text
Feature story
Featured source: Eugene Sickler
“The lug nuts on my Kawasaki payloader were so tight and rusted I couldn’t break them loose with a 1-in. impact wrench using 145 lbs. of air pressure,” says North Dakota heavy equipment operator Gene Sickler.
Read the complete story →From the archive · Full text
Feature story
Featured source: Norm Dufresne
Norm Dufresne does a lot of wood working so he doesn’t like to spend a lot of time changing router bits and adjusting the depth. That’s why he put together a portable router table with 4 routers set…
Read the complete story →From the archive · Full text
Feature story
Featured source: Keith Davis
“I came up with this design when a farrier asked me to carry his anvil without having to lift it into his truck,” says welder/fabricator Keith Davis of Cody, Wyo. He designed and built a foldable hitch that…
Read the complete story →From the archive · Full text
Reader shop tip
W. Gray Abercrombie, Broad Run, Va.
“The on-off solenoid switch on my 1994 Dodge pickup equipped with a Cummins diesel engine went bad. I saved money by substituting the push-pull cable off a tractor.”
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Ralph Curtiss, West Grove, Penn.
His tool wagon makes maintenance and repair easy. Instead of running back and forth for tools, he pulls his tools with him.
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Kevin Feller
Ceramic coating of high-heat parts keeps them looking good and working better, according to Kevin Feller. He and his wife Amy run K & A Coatings. While they do powder coatings too, it is the ceramic coatings that…
Read the complete story →From the archive · Full text
Reader shop tip
“In your last issue a reader complained about loose steering on his Chevy Tahoe. I used to be a GM tech and I’ve fixed lots of steering problems on earlier GM trucks. The problem often is in the…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Tony Ryba, Johnstown, Penn.
“My 2001 F-250 Ford pickup with a 5.4 engine, has 144,000 miles and still has the original U-joints, starter and battery. Once a month I lube the U-joints with a motorcycle chain lube, working it into the joint…
Read the complete tip →From the archive · Full text
Feature story
Featured source: Roxanne Winslow
You can sandblast an old tractor, pickup or car without making a mess using a “Bad Dust®” containment bag that completely encloses the workspace inside a bag.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Gale Banks
The Ram-Air intake system from Banks Power promises to boost mileage and power, thanks to the filtered, denser and cooler air it feeds into the engine. The high-performance system has been available for gas and diesel-fueled truck and…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Treadwell Carburetor Co.
Treadwell Carburetor Co. in New York has a long history of rebuilding car, truck, industrial engine and farm tractor carburetors.
Read the complete story →From the archive · Full text
Reader shop tip 2 of 4
Individual tip 2 of 4 from this reader’s published contribution.
Edwin Ruff, Boise, Idaho
“The rechargeable battery on my 12-volt cordless drill went bad, so I attached 2 wires to the end of a wooden block that installs in place of the battery to make contact with the drill’s power plugs. I…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Vernon Knaack, Correctionville, Iowa
“2. The 30 and 40 Series Deere tractors use the same AC compressor as General Motors vehicles did during that time period. This spring a Deere dealer quoted me $550 for a new one. My local NAPA store…
Read the complete tip →From the archive · Full text
Reader shop tip
Bill Reeks, Cromwell, Ky.
“I’ve had trouble over the years with the fuel pump on my 1984 Suburban. I solved the problem by switching to an electric fuel pump. Worked great. This idea can help many older vehicles.”
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Dave Bulawsky, Auberry, Calif.
“I built my own pitman arm puller out of a piece of scrap square tubing. I cut a notch out of one end, welded a 1/4-in. nut on top, and inserted a bolt. It works perfect. I’ve used…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Kevin Lehnert
Kevin Lehnert’s frustration with starting older 6-volt machines led him to a better idea and his own business. He supplies custom CNC-machined battery packs that include a pair of Optima 6-volt AGM Red Top batteries harnessed together in…
Read the complete story →From the archive · Full text
Feature story
Featured source: Lance Hartman
“Our DieselFlex injection system blends measured amounts of CNG or LPG into diesel engines using state-of-the-art fuel management technology,” says Lance Hartman, branch manager of Maxquip, in Saskatoon, Sask.
Read the complete story →From the archive · Full text
Reader shop tip
Andrew Sewell, North Yorkshire, England
“A friend of mine needed a decent-sized tractor to power a pto-powered mobile dryer, but he didn’t have one to spare. However, he had an old unused truck with plenty of power, but no pto output. So he…
Read the complete tip →From the archive · Full text
Reader shop tip
Larry Bultman, Okawville, Ill.
“I buy all sizes of freezer zip lock plastic bags to store miscellaneous parts in my shop area, and in toolboxes on trucks and tractors. Keeps them clean and you can always see what’s inside.”
Read the complete tip →From the archive · Full text
Reader shop tip
Ron Cole, Clive, Alberta
“When we put up silage in late summer there’s always a lot of chaff blowing around that plugs up the radiator on our truck, making it difficult to keep the truck’s engine cool.
Read the complete tip →From the archive · Full text
Reader shop tip
Roger Gutschmidt, Gackle, N.Dak.
“This winter I painted the rubber belts on my round baler with Herculiner truck bed liner.
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Eric Rego
Get a gear reduction starter from Maple Springs Farm and your Oliver won’t grind down the battery on a cold morning. The modern style starter gives the extra cranking speed needed to turn over the engine without running…
Read the complete story →From the archive · Full text
Reader shop tip
Albert Holt, Butternut, Wis.
“I made a handy tool trailer from a 250-gal. fuel oil tank. I cut it in half and welded angle iron around the inside edge. The lower angle iron sticks up 3/4 in. and the upper angle iron…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Jim Kral, New Ulm, Minn. (ph 507 354- 1945; www.kralautoparts.com)
“My new exhaust manifold bolt repair kit is designed to stop exhaust leaks between the exhaust manifold and cylinder head on 1999 and newer model GM trucks and SUV’s equipped with 4.8, 5.3, 6.0 or 6.2-liter engines. The…
Read the complete tip →From the archive · Full text
Reader shop tip
Melvin Stoner, Calumet, Okla.
“I built a handy hitch for my torch cart that lets me pull it with a garden tractor. It’s a lot easier than trying to load the cart into a pickup or loader bucket. I made the hitch…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Brendan Leep
“We call it the Shop Dog and there’s no other machine like it that we know of,” says Brendan Leep, Manhattan, Mont., about the new shop machine he developed with partner Brad Moss. It’s designed to replace the…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Powermaster
The PowerGEN from Powermaster offers the output and reliability of an alternator with the looks of a generator. It’s a great way to update older tractors, cars and trucks.
Read the complete story →From the archive · Full text
Feature story
Featured source: Scott Bruce
When Scott Bruce of Ozark, Mo., found an old straight-six engine block at a dump, he decided to use it to build a heavy-duty workbench.
Read the complete story →From the archive · Full text
Feature story
Featured source: Todd Carlson
Gary Carlson wanted to put a cab on his 1999 Kubota F2560 garden tractor to make blowing snow more comfortable. The Eau Claire, Wis., resident went looking on Craigslist and found an old Kubota cab from a compact…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Dwayne Ditz
If you’ve got a digital display that goes bad, it can cost you thousands of dollars. Instead, you can call Dwayne Ditz, who will repair and reprogram defective instrument clusters that dealers would normally replace. The difference can…
Read the complete story →From the archive · Full text
Reader shop tip
Joe Silcox, Crossville, Tenn.
“One problem with ramps used to work on vehicles is that once the wheels are up on top, the slanted part of the ramps are still in the way of your creeper. I solved the problem by building…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip
Ken Grazier, Havre, Mont.
“I made a ‘pickup’ tool that really comes in handy around my place. It has a magnet at the top for picking up nails, bolts, and other small parts. It’s 4 1/2 ft. long and made from a…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Blane Burnett
If you’re looking for a massive boost in power for cars or pickups, Holley Performance Products have what you need. The Dominator in-line billet fuel pumps can provide up to 1,800 hp EFI or 2,100 hp carbureted. The…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Brendan Cashman
Owners of light trucks, Jeeps and SUV’s should take a look at EBC Brake pads, made from a new material designed to self-clean, stay cooler, grip better and last longer.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Kevin Bealer
PA Performance has been building, customizing and modifying vehicles for more than 20 years. In the process they’ve learned how to upgrade electrical components to provide greater performance.
Read the complete story →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Lloyd R. Lucas, High Springs, Fla.
“I was going through a lot of air filters on my Kubota UTV until I made this change. I ran a long piece of pvc from the filter up through the roof of the vehicle. Pulls in clean…
Read the complete tip →From the archive · Full text
Reader shop tip
Mark Vroman, Buffalo, S. Dak.
“I mounted a 6-in. vise on a piece of pipe that slides into a bigger pipe mounted on my pickup’s receiver hitch and also into a pipe mounted on two stacked pickup rims in my shop. Let’s me…
Read the complete tip →From the archive · Full text
Reader shop tip
Robert McMahon, Knoxville, Tenn.
“We use a small 4-WD Kubota loader tractor and a 3-pt. mounted, 6-ft. Woods finish mower to cut grass. We farm a lot of rough terrain and when we made a sharp turn with the tractor, we accidentally…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Ron Peck
Ron Peck has driven nearly 1.1 million miles delivering gravel with his Keystone Lime Co. Ford dump truck. They weren’t easy miles. The company quarry is on the west side of the highest point in Pennsylvania, and most…
Read the complete story →From the archive · Full text
Feature story
Featured source: Performance Injection Systems
You can boost horsepower on a 7.3 Power Stroke engine with remanufactured injectors from Performance Injection Systems (P.I.S.). The company offers a variety of options and is expanding to include common rail Dodge/Cummins engines from 2003 to 2007,…
Read the complete story →From the archive · Full text
Feature story
Featured source: John Niesel
John Niesel, Palominas, Ariz., recently sent FARM SHOW photos of the “poor man’s” rack he came up with for his riding mower.
Read the complete story →From the archive · Full text
Feature story
Featured source: Brian McCormick
Pickup owners often complain about their vehicle’s “nose diving” look when there’s no weight in the box. A Nevada company has a solution to that problematic situation with a product called Ready Lift. It’s an easy-to-install leveling kit…
Read the complete story →From the archive · Full text
Reader shop tip
Harold Fratzke, Cottonwood, Minn.
“I made a portable hydraulic press that can be used with any hydraulic jack.
Read the complete tip →From the archive · Full text
Reader shop tip
Dick Clevenger, Letts, Iowa
“The gearbox and shaft wore out on my Aeromotor windmill. To get the windmill running again I ‘repurposed’ the front wheel, spindle, and kingpin assembly off a 1961 GM 1 1/2-ton pickup. I welded them to a length…
Read the complete tip →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
Milan Hochstetler, Cumberland, Va.
“To reach the window crank on the passenger side of my pickup, I attached a short length of pvc pipe to a broom handle.”
Read the complete tip →From the archive · Full text
Feature story
Featured source: Firestone
If you do a lot of hauling or towing, Firestone’s Ride-Rite Air Helper Springs can make the job safer and the ride smoother. The airbag kit levels and balances loads as needed, reduces “bottoming out” and increases stability.
Read the complete story →From the archive · Full text
Feature story
Featured source: Tyler Buchheit
Ask Tyler Buchheit any question about a vintage Deere moldboard plow and chances are he’ll have an answer. Even though Buchheit is only in his mid 30’s, he knows exactly what he’s talking about.
Read the complete story →From the archive · Full text
Reader shop tip
Allen Dilg, Gurnee, Ill. (ardilg@yahoo)
“We do a lot of tractor restorations and came up with an easy way to get rid of crud in a vehicle’s fuel tank. Open the drain on the carburetor, and the fuel should run out in a…
Read the complete tip →From the archive · Full text
Reader shop tip
Anonymous, Richmond, Va.
“Bar chain oil for my chainsaw is about $25 a gallon. So I use old motor oil. After I change oil in a car or truck, I let the oil sit for a day or so in the…
Read the complete tip →From the archive · Full text
Reader shop tip
Chad Travis, Drasco, Ark.
“I made a wheeled bucket stand for a local auto garage. It’s designed to support a 5-gal. bucket of fluid 3 1/2 ft. off the floor, which makes pumping fluid into gearcases a much easier job when the…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
George Kronbach, Yulee, Fla.
“My 1988 Chevrolet 3500 diesel pickup would start only if I sprayed ether in the air intake.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
George Kronbach, Yulee, Fla.
“I use Amsoil products in the same pickup and installed the company’s dual remote bypass oil filter system. It traps the extremely small, wear-causing contaminants that full-flow filters can’t remove. Now I can go about 25,000 miles between…
Read the complete tip →