From the archive · Full text
Reader shop tip
David Bender, Aylmer, Ont.
“When welding a piece of rusty equipment, it’s sometimes a problem getting a good ground with the ground cable clamp. Here’s a remedy. First clamp a common vise-grip wrench on the rusty spot, and then clamp the cable…
Read the complete tip →From the archive · Full text
Reader shop tip
Elroy N. Lindaas, Mayville, N. Dak.
“This handy hoist, built from a discarded swing set, provides me with a safe and easy way to clean the deck and sharpen the blades on my riding mower. Once the riding mower is on the hoist I…
Read the complete tip →From the archive · Full text
Reader shop tip
Ken Greenia, St. Clair, Mich.
“To remove a stud that has broken off flush, I lay a flat washer over the broken stud and weld the two together. Then I weld a nut to the washer and remove the stud by working it…
Read the complete tip →From the archive · Full text
Reader shop tip
Miles Parkkonen, Negaunee, Mich.
“A while back someone wrote about weld- ing on a compressor tank. I just want to remind people not to weld on any tank that is pressurized. One of my friends got killed when he attempted to do…
Read the complete tip →From the archive · Full text
Reader shop tip
Paul Tierney, Bloomington, Minn.
To make it easier to make tough cuts with his bolt cutters, Paul attached a round piece of plate steel to one handle so he can place it flat on the ground and apply force to the upper…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Tim Hays, Oreana, Ill.
Tim also mounted a metal break and roller on top of a rolling warehouse truck that he bought at a factory closeout auction. The truck is heavy enough to carry the tools easily and handle the pressure applied.…
Read the complete tip →From the archive · Full text
Reader shop tip
Jerry Lanser, Associated Electric Prod- ucts, Inc., P.O. Box 6713, Longmont, Colo. 80501 (ph 800 361-6314;jlanser@assoc- elec-prod.com; www.assoc-elec-prod.com)
“Our Drill Bandit attaches to most pistol-type drills and allows you to put as much pressure as you want on the drill bit simply by squeezing the ratchet. Works great in many difficult-to-drill applications.
Read the complete tip →From the archive · Full text
Reader shop tip
Robert L. Stone, 1504 Dillon Rd., Sey- mour, Mo. 65746 (ph 417 767-4395)
“My multi-purpose Truk-R-Tool is designed for truck drivers but it comes in handy for just about anyone. The 17-in. long, powder-coated tool has a railroad spike welded to a hollow steel pipe handle. There’s a steel retractable hook…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Roger Gutschmidt, Gackle, N. Dak.
He uses a simple trick to get bolts through openings where you can’t get your fingers inside. He wraps a piece of .035 welding wire tightly around a 5/16-in. bolt.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Roger Gutschmidt, Gackle, N. Dak.
“I’ve found endless uses for rare earth magnets around the shop. I have steel walls and cabinets in my shop so I’ve got these little magnets stuck all over the place, holding parts, manuals, etc. They’re so unbelievably…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
“I changed the shape of one of the skid shoes on my Deere 630 Hydra Flex combine header because it wasn’t working as well as I wanted,” says Roger Gutschmidt, Gackle, N. Dak. When combining this year’s soybean…
Read the complete story →From the archive · Full text
Feature story
Featured source:
“We do site prep work for timber companies, and the brush is hard on hydraulic hoses,” says Robert Raymond, Cove, Ark.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Frame walls out of line? Ready to grab a mall or pry bar to bring them back? Contractor Keith Kennedy was tired of pounding on walls, and the only wall puller tool on the market required at least…
Read the complete story →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Gilbert F. Conn, Pittsburgh, Penn.
“A case-hardened bolt broke off on my tractor’s water pump and I wasn’t able to drill it out, so I used a Dremel tool and four small grinding stones to do the job. The grindstones I used are…
Read the complete tip →From the archive · Full text
Reader shop tip
L. Putnam Foley, Bulger, Penn.
“I had problems with hay plugging up in my 1992 New Holland 848 round baler due to worn rollers. I was able to get the bale started, but the rollers were so slippery the hay wouldn’t keep going…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 3
Individual tip 1 of 3 from this reader’s published contribution.
Steve Reeves, Benton, Ky.
“I use the teeth on my 21 hp Kubota backhoe to cut through tree roots. On big roots I use the teeth like a knife blade to shave the root down until it’s thin enough that I can…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Steve Reeves, Benton, Ky.
“Eventually the teeth get dull and don’t do a good job of cutting through the roots. Then I use a hard surface welding rod and build the teeth back up with new metal. I use a grinder on…
Read the complete tip →From the archive · Full text
Reader shop tip
Eric McNutt, Sulphur Springs, Ohio
“My home-built welding table makes use of a simple 2-wheeled dolly and folds up for transport and storage. As a result, the table doesn’t take up much more storage room than the dolly itself.
Read the complete tip →From the archive · Full text
Feature story
Featured source:
“It’s a simple, low cost way to raise our riding mower up in the air so we can easily service it,” says Roger Foster, Tower Hill, Ill., who made brackets for his commercial 10,000-lb. rotary hoist to raise…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Nate Regier, Sutton, Alaska, works at a Bible camp in Alaska where he’s in charge of the auto shop. He recently sent FARM SHOW photos of a system he came up with to collect waste oil in the…
Read the complete story →From the archive · Full text
Reader shop tip
H.R. Heisley, Egg Harbor Township, N.J.
“An easy way to collect metal fines from engine oil is to remove the drain plug, drill a hole through the center of it, and insert a pencil magnet so it sticks up into the oil pan. Glue…
Read the complete tip →From the archive · Full text
Reader shop tip
Roger Gutschmidt, Gackle, N. Dak.
“When I need to make a big spring longer without permanently stretching it, I have a couple of tricks that I use. These ideas work on all springs, little or big. Sometimes you have a really strong spring…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Old combine hydraulic steering motors can be used to make a shop press easier to operate, says Orvie Wideman, Wallenstein, Ontario, who replaced the spool control valve on his shop press with a hydrostatic steering motor off an…
Read the complete story →From the archive · Full text
Feature story
Featured source:
“It hangs on the side of my tractor in a pvc mounting bracket. I find all kinds of uses for it,” says Eric “Moose” Petrevich, Glen Gardner, N. J., about his homemade hammer with a chisel hidden in…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Louis Giesting added 40 hp to his Massey Ferguson 1105 when he switched engines. Repowered and cleaned up, the 1105 is back in the field again and working better than ever with its Fox engine.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Georg Hertz-Kleptow of Dapp, Alberta couldn’t justify the cost of a commercial hydraulic-cylinder sleeve puller, so he made his own. With only about a $360 investment and 12 hrs. of his time, Hertz-Kleptow built a unit that serves…
Read the complete story →From the archive · Full text
Feature story
Featured source:
When his father suggested that Ryan Lusk put a Cummins engine in his 1968 Corvette, Lusk dismissed the idea. But when two friends said it couldn’t be done anyway, Lusk couldn’t ignore the challenge. He proved them wrong,…
Read the complete story →From the archive · Full text
Feature story
Featured source:
With her three patent-pending clamps, Re-nae Becker can easily reconfigure and repair the horse corrals on her California ranch.
Read the complete story →From the archive · Full text
Reader shop tip 2 of 3
Individual tip 2 of 3 from this reader’s published contribution.
Dennis Martin, Live Oak, Fla.
I’ve also used stainless steel 1/2 in. dia. pipe to make a handle for a garden rake, putting a hoe on the other end so I’ve got two units in one.
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Dennis McCarville, Two Harbors, Minn.
“Also, water is the best metal and drill bit cooler there is. Don’t use oil. Water keeps the contact points cool and increases the cutting power of the bit. It’s also a lot less messy to use.”
Read the complete tip →From the archive · Full text
Reader shop tip
Mark Eilers, Tower Hill, Ill.
The steel roof on Mark Eilers’ farm shop leaks over his workbench. It only happens when the wind’s coming from a certain direction.
Read the complete tip →From the archive · Full text
Reader shop tip
Marvin Wells, Spencerville, Ind.
“If you have trouble keeping your chuck key handy for a drill, just take a speaker magnet out of an old radio and stick it to the side of the drill (must have a metal casing). Then stick…
Read the complete tip →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Don Burke
“It’ll grab onto fasteners that standard wrenches can’t handle,” says Don Burke, BurkTek Inc., Kansas City, Mo.
Read the complete story →From the archive · Full text
Reader shop tip
Dean Larson, Tescott, Kan.
“I recently put up some fencing using 5 by 100-ft. rolls of 6 by 6-in. wire. It looks much like concrete reinforcing wire but is heavier gauge and galvanized. To bend the wire around itself I used a…
Read the complete tip →From the archive · Full text
Reader shop tip 2 of 2
Individual tip 2 of 2 from this reader’s published contribution.
Jim Kissock, New Bloomfield, Mo.
“If you have a small hole in a metal water tank, use a roof washer that has metal on one side and a plastic washer on the other side to bolt through the hole. Tighten the nut on…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
Grainhead auger centers get messed up pretty bad over a couple of seasons. Instead of re-placing the entire auger, Marshall Enterprises will just replace the damaged center. Or they can ship you a kit so you can do…
Read the complete story →From the archive · Full text
Feature story
Featured source:
Frank Slapar, Pittsburg, Kansas, used scrap sheet metal and some plastic pipe to come up with a better intake air pre-heater for his 1941 Farmall M tractor.
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: Darrell Boren
Darrell Boren bends 18-gauge metal sheets into Deere tractor hoods, specializing in the styles that are the most difficult to make without using expensive dies and presses.
Read the complete story →From the archive · Full text
Reader shop tip
Elmer Pinkerton, Elmwood, Neb.
“When welding and cutting, it’s quite a chore to keep changing torches and resetting the oxygen gauge. I made it a lot easier by installing a T fitting on the oxygen tank and fitting it with a second…
Read the complete tip →From the archive · Full text
Reader shop tip
Jerry Foster, Magalia, Calif.
“In your last issue someone installed an electric plug-in socket on his Lincoln welder so he could use it to operate power tools. He removed the back of the welder and ran wire to the 110-volt socket, including…
Read the complete tip →From the archive · Full text
Reader shop tip
Mark Eilers, Tower Hill, Ill.
He came up with a lightweight metal brake that fits onto the front edge of his workbench. He first lag-bolted a long piece of 1/4-in. thick steel plate to the front edge of the bench, leaving a thin…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
If hammers, flails, rods and screens are failing faster than you think they should, it may be time to check out Doran Manufacturing. Randall Doran says they use higher quality steel than OEM’s and harden it, too.
Read the complete story →From the archive · Full text
Reader shop tip
Gary Combs, Concord, Ohio
“My 1989 Belarus 25 hp tractor used to steer like an old steel-wheeled Fordson. Now it steers so easy I feel like the King of Siam when I’m driving it. I added power steering to my 1989 Belarus…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
If your drill bits are slipping in the chuck, your chuck may be worn. To solve the problem, Joe Gibbs came up with a way to modify bit heads to give the worn chuck something to grip.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Kit Talbot is the CSI facilitator at Schulte Industries of Englefeld, Sask. He recently sent photos to FARM SHOW of a heavy-duty, adjustable welding table he and other employees made from scrap steel.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Sooner or later, all steel fuel tanks are likely to have the same problem. They will begin to rust, flake and develop pinhole leaks.
Read the complete story →From the archive · Full text
Feature story
Featured source:
Mark Musser, Beecher City, Ill., needed a tall work space in his shop building where he could work on big machinery during the winter. But he didn’t want to heat his entire shop. So he built a large…
Read the complete story →From the archive · Full text
Feature story
Featured source:
The loft storage area in Gene Boehler’s shop is much more useable now that he can get there by elevator.
Read the complete story →From the archive · Full text
Feature story
Featured source:
“It works much like larger engine stands designed to hold bigger Cummins and Cat truck engines, but costs much less,” says Kenny Peters about his company’s new portable engine stand that’s designed to handle tractor engines.
Read the complete story →From the archive · Full text
Reader shop tip 3 of 3
Individual tip 3 of 3 from this reader’s published contribution.
John Stava, Bloomington, Ind.
“I’ve read about all sorts of ways to pre-serve a partially filled paint can -everything from sucking out the air with your mouth to using expensive vacuum equipment. The rule to remember is, keep the paint can lid…
Read the complete tip →From the archive · Full text
Reader shop tip
Luther Newman, Clinton, Okla.
“I installed an electric plug-in socket on my Lincoln welder so I can use it to operate power tools. I removed the back of the welder and ran wire to the 110-volt socket, including a ground wire. I’ve…
Read the complete tip →From the archive · Full text
Reader shop tip
Peter Hansen, Gowen, Mich.
“I do a lot of welding and cutting and during the summer I usually wear a short sleeve shirt or T-shirt, which exposes my arms to a lot of sparks and heat. To solve the problem I made…
Read the complete tip →From the archive · Full text
Reader shop tip
Aaron Marley, Nokomis, Ill.
When Marley wants to air up a tire on a piece of farm equipment, he just pulls out a pressure hose from a reel that he attached to the top of his portable air compressor.
Read the complete tip →From the archive · Full text
Reader shop tip
Bob Heslop, Warner, N. H.
“I was putting an old Deere 420C tracked tractor back into working condition. The guide flanges on the front idler wheels were so worn the tracks kept coming off. To remedy the problem without spending a lot of…
Read the complete tip →From the archive · Full text
Feature story
Featured source:
It looks like any other steel building, but the walls of Tom Schuster’s 36 by 40-ft. shop are 40-ft. containers. He had parked two containers 20 ft. apart on railroad timbers in 1995 when he purchased his Pomeroy,…
Read the complete story →From the archive · Full text
Feature story
Featured source:
“I use my bench grinder for many different jobs. One afternoon while working on a project in my shop, I needed a fast cutting grinder for something I was working on. I noticed a few chop saw wheels…
Read the complete story →
Photo: FARM SHOWFrom the archive · Full text
Feature story
Featured source: General Tools & Instruments Co., LLC
You can use this new self-adjusting pipe wrench with one hand. There’s no need to spin a nut to adjust the size of the opening between the jaws. It lets you quickly switch between different sizes of pipe.
Read the complete story →From the archive · Full text
Reader shop tip
Al Smith, Springfield, Vt.
“I came up with a way to fix the 4-WD gearshift lever on my 1995 Ford F-150 pickup. One day the lever wouldn’t move so I pushed it with my foot and unfortunately broke the aluminum metal plate…
Read the complete tip →From the archive · Full text
Reader shop tip 1 of 2
Individual tip 1 of 2 from this reader’s published contribution.
Chad Travis, Drasco, Ark.
“A common problem with front tractor wheel rims is that the lips can get bent, allowing dirt to get under the bead. I use my tractor in the woods to pull logs and also to run a homemade…
Read the complete tip →